sp3500 instr new v1
Contents
1. SQUARE e PERFECT CMake every picture perfect STUDIO FLASH SET ovo voco c e Qty 2 Qty 1 Qty 2 Qty 1 Qty 2 Qty 1 Qty 1 Qty 1 Qty 2 SP3500 Professional Series Studio Light Kit SP160 Professional Studio Strobes Accessories 160 Watt Second 75 watt modeling light Qty 1 Collapsible Reflector synch Flash B 45 Watt Second 32 double sided Silver Gold Includes A C screw socket with umbrella holder Qty 1 Four Leaf Barn Door Light Stands extends from 31 to 78 9 Qty1 Set of 4 Color Gels Light Stand extends from 16 to 42 Qty 1 Honeycomb Filter Softbox 20 X 28 9 Qty 1 Snoot attachment Umbrella 33 gold reflecting umbrella 9 Qty 1 4 Channel Wireless Trigger Device Carry case designed to carry all SP3500 included SQUARE BS 1 Backdrop 10 x 20 large fabric backdrop PERFECT Includes light proof carry bag CMake every picture perfect www squareperfect com 2007 All rights reserved Square Perfect Photo Backdrops 6 x 9 one pure black and one pure white Includes light proof carry bag SP3500 Flash Studio Kit Thank you for your purchase of the SP3500 Flash Softbox Studio kit This manual has been written to help you with the assembly operating procedures and accessories Square Perfect s SP3500 Flash Kit is manufactured with the finest material available Your flash kit will provide many years of quality service with2. proper care and handling SP803 professional duty adjustable light stand Small stand for highlight fill strobe flash SP160 lamp body 12 power cord Four leaf barndoor Snoot will direct light to exact spot without affecting surrounding area 1 set Red blue yellow frosted and honeycomb filter Easy snap on attachment If fill strobe is not working be sure to check the on off switch Located on the back of the lamp holder Please read this manual carefully before use and keep it handy for use during break down of equipment Please read and heed all safety precautions listed in this manual For ordering spare bulbs or replacement parts contact us at info squareperfect com Also check out our extended line of photo equipment now available Varigated dye backdrop Four panel softbox set SP 4 lamp Black backdrop connector White backdrop Sa at Four leaf barn door set with color filter attached to the SP160 flash head on the SP803 stand 1 Swivel screw 2 Umbrella rod mount 3 Mounting screw Remove protective cover from mounting tip before attempting to place flash head on stand 2007 All rights reserved Square Perfect Photo SP160 Lamp Head Operation m 5 Flash test 6 Sync receptacle 7 Safety fuse 8 Charging lamp 1 On Off electric supply 2 Variable flash dial 3 On Off model lamp 4 On Off flash ready beep SAFETY PRECAUTIONS
3. Become thoroughly familiar with this product before use Run through at least one practice assembly and breakdown before you schedule a shoot Make sure that the main voltage corresponds to that stated on the SP lamp Account for number of lamps in use Never leave the lighting unsupervised when in use Keep children or incompetent persons away from lighting equipment f the lamp or the cord show sign of wear or damage it should be replaced or repaired by a qualified electrician before use Softbox Assembly T v 1 Pictured is the SP4 lamp ring 2 Small end of flex rod fit into connector shown with the corner pocket on the softbox large end of the flex rod inserted tent 7 Now close the velcro flaps as shown in the picture 6 Push the velcro strap into place just below the lip of the tent Note the rods take a good deal of force to flex into position 3 With three rods inserted into the ring and corners fold the SP 4 ring into the tent 8 The SP 4 ring can now be attached to the SP 160 flash unit lense with the velcro straps DO NOT over tighten Specifications Power Input AC110 130 volt 60 Hz Flash Power 160ws joule in full Guide No 120ft 36m ISO100 Color Temperature 5600K Flash Tube Lifetime over 8 000 typical flashing Flash Power Setting 1 16 to full Recharge Time 0 5 3 seconds in full Flash Duration 1 600 sec 1 1000 sec Slave Range 35ft 10m Lighting Ran
4. ge 55 degree Modeling Power Halogen 75w Bulb Base E 14 screw Synch Voltage 5 volt Fuse 5A Dimension 4 x 7 1 2 Weight 1 8 Lb 800g 9 Flash ready lamp 10 Slave dome 11 Flash ring 12 Model lamp Wait until the bulb is completely cool before touching or removing it Never use the SP lamp outside in a wet environment Never move the appliance by pulling the cord Make sure the cords do not come in contact with halogen bulb Do not wind the cord around the appliance Stand the SPon a flat surface only to prevent toppling Do not touch the metal parts on the lamp while in use these metal parts will become very hot 5 Insert the forth rod into the pocket on the velcro strap 4 Next insert the fourth rod into the SP 4 ring Note Keep the velcro flaps at the ring open to allow sufficient slack 9 Next attach the inner diffusion 10 Attach the outer diffusion lense to velcro patches on the outer edges 122007 All rights reserved Square Perfect Photo Electronic Radio Trigger Device The SP3500 Flash Kit is shipped with the a Wireless Triggering Device for your convenience It is an easy to use device that will give you extra control in the photographic studio environment The Wireless Triggering Device is designed to work with a variety of flash units We provide a wide range of sync cord adaptors to fit most popular brands The Wireless Triggering Device has four channels and u
5. re attempting any of the following procedures UNPLUG the unit Next check the fuse found on the back of the unit If it is tripped replace it Plug the unit in and recheck the flash bulb If it is determined the bulb is faulty a replacement can be ordered from info squareperfect com BULB replacement is simple and easy Before handling new bulbs remember to wear clean cotton glove Oils from skin will cause premature bulb failure Hold bulb close to base Gently push the two prongs into the receiving holes Next attach spring retaining strap Strobe flash bulbs may vary in appearance and shape from model to model replacement procedures remain the same unless noted
6. ses a 23A battery installed The receiver uses two AAA batteries not included To use the Wireless Triggering Device first slide the trigger into the hot shoe found on top on your camera If a hot shoe is not available use the sync cord attachment found on the side ofthetrigger device 2 Attach the receiver to a remote flash unit Use the proper sync cord adaptor provided plug into sync cord socket 3 Switch the receiver unit ON OFF button to the ON position Press the test button located on the top of the trigger unit You will see a twinkling of the LED on the receiver unit This indicates the trigger is working properly and is locked in on a working channel of the receiver 4 Switch the remote flash unit power switch to the ON position with the receiver attached Push the test button on the trigger it should trigger the remote flash unit 5 To change channels on the trigger slide the channel switch on the side of the trigger device to one of four positions Next press the power switch on the receive unit twice to reset the receiver if Roey F SQUARE o PERFECT www squareperfect com 2007 All rights reserved Square Perfect Photo Replacement Bulbs For ordering spare bulbs or replacement parts contact us at info squareperfect com Also check out our extended line of photo equipment Before replacing bulbs be sure to read the instructions and follow the safety procedures Befo
Download Pdf Manuals
Related Search