H800 Manual - Afinia 3D Printer
Contents
1. 11 Afinia H800 3D Printer User s Manual Getting Ready to Print Starting the Afinia 3D Program Open the Afinia 3D software on the desktop Windows or in the Applications folder Mac tina v25 m a RZEZ eoo 30 Print CELETE lt Windows version Mac version Initializing the Printer Long Press the Power Button or click Initialize in the 3D Print menu The printer will beep the platform and print head will move to the printer s home positions and beep again when it is ready eb nie Tools View Wi Edit View Tools Help Setup etm Calibrate pum qas Platform Calibrate Calibrate Yd ka Platform Calibrate gt Auto Level Auto Level About Nozzle Height Detect Nozzle Height Detect Print Preview Print Preview Print Ctrl P initialize Maintenance Table Heat 15 mins Maintenance Table Preheat 15 mins Print Windows version Mac version TIP If your printer is not responding properly always first try to re initialize the printer 12 Afinia H800 3D Printer User s Manual Preparing the Platform The print platform needs to be prepared so the model adheres to the platform enough to be printed while still being easy to remove from the platform when done Never print directly to the aluminum platform There are several options FR 4 Board Glass reinforced Epoxy Laminate The FR 4 Board also called the Perf board is held in place by the 13 mounting screws and two spring loaded bearings Appl2. Once you have found the calibration point with the lowest nozzle height move to that point and adjust the platform position so the nozzle is just touching the print surface Click Set nozzle height Once the nozzle height is set select the distances from the drop down lists that brings the platform at the other 8 points into contact with the nozzle Once all 9 values have been entered click Apply current values Reset will clear all calibration values Click Quit when you are finished Platform Calibration 1 Move platform to nozzle Move the platform using buttons 1 through 9 below to find the point on the platform that first contacts the nozzle Use the Up and Down buttons to raise or lower the platform as needed Up CurHeight 133 09 Down Set nozzle height 132 88 2 Enter the distance from nozzle to platform at each of the 9 points 1 0 0 2 0 0 3 0 0 4 S 10 0 6 10 0 7 8 0 0 9 10 0 3 Confirm Apply current values Platform Calibration 1 Move platform to nozzle Move the platform using buttons 1 through 9 below to find the point on the platform that first contacts the nozzle Use the Up and Down buttons to raise or lower the platform as needed Up CurHeight 133 09 Set nozzle height 132 88 Down 2 Enter the distance from nozzle to platform at each of the 9 points 1 0 2 7 20 1 7 3 10 1 40 1 7 5 0 0 7 6 0 0 7 700 3 v 8 0 2 7 90 0 7 3 Confirm Apply current value
3. The Print Head is held in place using three guide magnets in the extruder bracket socket t Filament Ribbon cable Entry Filament Entry Metal Plat ux mu Magnets Wind barrier lever n 5 Y E a r Pa Extruder Block a i le Mozzle Mozzle Automatic Leveling Probe Automatic Leveling Probe LEFT HAND SIDE VIEV LEFT HAND BACK VIEVY FRONT VIEW The Print Head is already installed in the Printer You do not need to do any assembly The Control Buttons You can do a lot with your Afinia H800 by using the Control Buttons so it follows your every command You also use the Afinia software to control the Afinia H800 15 mins SINGLE PRESS OW Vo S ee DOUBLE PRESS LONG PRESS Filament Button Power Button Pause Button Afinia H800 3D Printer User s Manual Installing the Afinia H800 3D Printer You will need the USB Cable Power Supply and Cable and Filament Spool to complete the Afinia H800 3D Printer installation Driver and Software Installation Mac Insert the Installation Disc into your Mac Open the disc go into the Mac folder and double click Afinia Mac Setup pkg Follow the prompts through the installation The drivers will be added and the Afinia software will be installed to the Applications folder Windows Insert the Installation Disc into your PC If the installer does not launch automatically start the Afinia 3D Printer setup exe file in the
4. Printing with the H800 3D Printer eesleesseeesee eere nene enne nn nnne nnn nnn nnn 20 ko ding a 5D Ni foo eror 20 MIEWODUONS AGS aaa aes oa OE POPE eae oases veld cine cient WACH 22 Modeliransiormatonsza sn kd Ua OOO aaa Rak 22 Placing Models onto the Build Platforim sscscccssssessecsessesseccncnssssecsecssssectecsscessessessessesssscensess 24 PRR Se UU DY ODEO MS Gw EA OGG DC EOT 25 PEIDUS CRINE S anie AREA PEP OO AO O A AO OE QNID AA A A 25 Part SO CUI OS aka oai o AO ai nnde to ceu piti oto M A UM Lu A W man Rd nU Sad 25 PCNA ad asta ias ds Sa iut uptime tai t UU cubil a 29 PONCODUO S ucisk M 29 Save aS PlOlSCC RENTRER TIT TT 31 Model RemoVal eR 32 Removing Support Material ccccccssscccsssscccessccccsnscccaenseesseaececsenecesseuseeseaeesseuscesseaeeeseaesessaneeeess 33 Maintenance tr M 34 Changins tie FIDE eser path ID oa ties EET EYRRA T REDAPI FU pE aot UR ERSOTAS TAa RP OO E OE 34 CI GNINS tine NOZ Ca 35 Removing Changing the No22zle ated etus Era suada eU INE po aor kw tote A Gadd a ad 35 Cleaning the Extr der OBals ue c uh A AGO es ate s te Uc ique eee 36 Cleaning De Platio rosso eio seat quis AEC IS eR EN 37 E brication ol Extra der Ralls 2 5 bes ti peat A NEAR WA AJ 37 Changins the IEPA FITE ocio ae poete ED tttm m etit EE AP Iu ide 37 Spare ANUS odes ass e ONAR G
5. Restore Defaults Cancel Mac version Windows version Print Settings Z Resolution This setting decides the layer thickness of the printer Options are 0 10mm to 0 40mm thick layers Part Settings Angle The Part Angle sets the horizontal printing orientation for fill printing At 45 Deg the part will be filled in with material printed at 45 degrees to the X and Y axes The orientation of the part itself will not be changed just the angle the fill material and solid layers are printed Surface This setting determines how many layers form the bottom face of a part when it is not solid If you set it to 5 the printer will print 5 complete layers before printing infill You may see more layers printing solidly if you are using very thin layer thicknesses This is normal This does not affect the side wall thickness which will be approximately 1 5mm regardless of the fill mode 25 Afinia H800 3D Printer User s Manual Fill Settings There are four ways to fill the interior of the parts as described below The part is 50 filled The part is 25 filled This Fill setting is recommended for This is the default Fill setting functional engineering parts Mac setting Solid g ERO e Ej Mac setting Loose Mac setting Hollow o E Mac setting Big Hole The part is 17 filled The part is 12 filled using the least amount of material 2 wb D P c bw a 4 4 m a Yee ON 2 Bo C addo wa ni e
6. 0 5096 100 Table pre heating progress or print progress during printing Changing Languages The Afinia software interface can use multiple languages To change the language open the application and enter the correct key sequence from the table below The language will change the next time the application is launched CTRL ALT N PC Default Language CTRL ALT E English CTRL ALT T Traditional Chinese 41 Afinia H800 3D Printer User s Manual Updating the Printer ROM Note This is a function that should only be performed if necessary 1 With the H800 Printer on and initialized select Update ROM from the Tools menu 2 Click OK when asked to confirm that you want to update the ROM 3 Click OK to select the ROM update file 4 Use the browse to find the updated ROM file This file will be located in the C Program Files Afinia System folder The file name will include the ROM version just before the ROM file extension Click Open when the correct file is selected o u Verify that you have selected the correct file and click OK Click OK again to begin the update When notified that the update is complete follow the prompts and power cycle the H800 Long Press the Initialize button on the control panel 9 Select About Afinia under the Help menu PC of Afinia menu Mac and verify that the new ROM version has been applied Troubleshooting Probier or Enor messade amm 0808 Verify power cord is securely
7. To avoid burning or model deformation do not touch the model nozzle or the platform by hand or any other part of the body while the printer is working or immediately after it has finished printing Protective glasses should always be worn when removing support material especially PLA There is a slight smell from ABS when it is being extruded A well ventilated room is recommended however when printing keep the printer away from any drafts as this can affect the warping of ABS prints When ABS is burnt it releases toxic fumes Never set the nozzle temperature high enough to burn the material The following classifications are used in this manual CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury WARNING Indicates a potentially hazardous situation which if not avoided may result in serious injury GLOVES When performing certain maintenance procedures the machine may be hot and gloves are required to avoid burns SAFETY GLASSES Wear safety glasses to avoid injury to your eyes Protecting the Printer The printer must not be exposed to water or rain or damage may occur Do not shut down the Afinia H800 3D System or pull out the USB cable when loading a digital model or the model data may be lost When using the Extrude function keep at least 50mm between the nozzle and the platform If too close the nozzle may get blocked The printer is designed
8. Top Door Filament feeder tube Filament Spool Magnetic Cover Front Door USB Interface Power Interface Power Switch BACK VIEW Print Head X Axis Z Axis Air Filter LED Status Bar Print Platform Internal View Afinia H800 3D Printer User s Manual Unpacking the Afinia H800 3D Printer The Afinia H800 3D Printer weighs over 40 pounds and should be team lifted Remove the power cord and 4 perf boards from the top foam piece Remove top foam from the box Lift the foam ring from around the printer With two people carefully lift the Printer from the box Lift the foam sheet below the printer and remove the Accessory Pack Power Supply Putty Knife and Snipping Pliers Lift the top cover and carefully lift out the foam above the platform AFINIA Open the front door and carefully remove the two pieces of foam from under the platform Tip each foam piece back until it is lying flat then turn the foam counter clockwise until the left end of the foam is through the door Use the snipping pliers to carefully cut the 6 labeled retaining strap loops from around the Print Head rails near the top of the printer Cut only the straps Next check the Accessories e Reel of Filament 1 Natural White e Power Supply e Power Cable e USB Cable e Extra Nozzle e Nozzle Wrench e Hex Wrenches e Putty Knife e Snipping Pliers Afinia H800 3D Printer User s Manual The Print Head
9. axis button the model will move again For example To move the model 5mm along Z axis or down 5mm 22 Afinia H800 3D Printer User s Manual 1 Click Move E 1 Select the Move option 2 Input 5 in the text box 2 Input 5 in the text box 3 Click the Z axis button 3 Click the Z button Windows TIP If you hold down the Ctrl key you can drag the model to a position Rotating the Model Click the Rotate button on the toolbar choose or input into the text box how many degrees you want to rotate and then choose the axis of rotation Rotate For example To rotate the model around Y axis by 30 1 Click Rotate z 1 Select the Rotate option 2 Input 30 in the text box 2 Input 30 in the text box y 3 Click the Y axis button 3 Click the Y button Positive numbers rotate the model counterclockwise negative numbers rotate the model clockwise Scaling the Model Click the Scale button on the toolbar choose or input in the text box a scaling factor and then scale the model uniformly by clicking Scale If you only want to scale along one axis click the axis around which you want the change to be applied Scale Example 1 Scale up the model uniformly by 2 0 times 1 Click Scale i Select the Scale option 2 Input 2 0 in the text box ale Input 2 0 in the text box 3 Click the Scale button ET Click the Scale Scale button Example 2 Scale up the model by 1 2 times along
10. common plastic used in 3d printing A strong and generally easy material to print with but printing large parts can warp PLA PolyLactic Acid is a biodegradable material derived from corn It warps less than ABS but support removal can be harder PLA is a great material to use in investment casting or lost wax casting Raft The printer lays down a foundation before it starts printing the model The raft is used to anchor the model down onto and into the perfboard as well as correcting any unevenness in the raft Perfboard A reusable and removal build platform that the model is printed onto included Shell The external layers of the printed part much like an egg shell Infill The internal honeycomb structure that gives the part strength Smart Support The Afinia software automatically generates supports scaffold for any overhangs of the model during printing like building a bridge and having scaffolding to support it MEM Melted Extrusion Melting the process of melting plastic and 3d printing like a hot glue gun Wind Barrier A small flap at the bottom of the print head that controls the air flow onto or away from the nozzle Air blowing over the nozzle cools the molten plastic quickly and can improve print quality but may cause weaker parts and warping Warping When a part lifts away from the platform caused by a poorly calibrated platform or the uneven cooling of the part during printing as the material shrinks back to its normal state
11. keeps the platform temperature hot after printing is complete which may make it easier to remove the model from the platform It also keeps the platform heated so you can start your next print more quickly Pause At Enter heights in millimeters to pause the printer at those heights during printing Multiple heights can be entered into the setting separated by commas Entering 13 5 20 27 25 will automatically pause the printing when it has reached 13 5 millimeters 20 millimeters and 27 25 millimeters This can be useful for changing filament or adding a non printed part at a specific point during the printing of the model You do not need to add the height of the raft to the numbers you enter the software will do this for you Use the printer buttons or the Maintenance window during the pause to perform the Withdraw Extrude and Resume Print functions 30 Afinia H800 3D Printer User s Manual Calculating model costs Afinia Calculate the cost of the material that will be used for your model using the Print Preview option under the 3D Print menu The application will Materials 17 7 g calculate the total weight of material used including the raft and any support material Use that weight to determine the cost to print the model using the following formula Cost of Spool Full Filament Weight Cost to Print Weight of Model X Use the weight of the filament that you purchased not the current weight of the spo
12. plugged in Verify the power switch on the back of the printer is on Extrud latf fails t Verify printer has initialized If not Long Press the Power xiruger or pratorm tal S tO button on the control panel to initialize the printer Heater is damaged Contact Technical Support page 46 Material is stuck in the extruder remove the material see page 34 The nozzle is clogged and needs to be cleaned or changed see page 35 reach operating temperature Material not extruding Print Drivers are not installed Run the full installation Printer not initialized use Initialize button on the control panel or Initialize function in software Cannot communicate with Make sure the USB cable is connected to the printer and to printer the computer Contact Technical Support see page 46 42 Afinia H800 3D Printer User s Manual Solution for Winusb dll not found problem Windows If you encounter a Winusb dll not found error message please FE follow the steps below General Computer Name Hardware Advanced Automatic Updates Remote Device Manager Option 1 Uninstall Older Driver and Auto Install New Driver Ur rcs R n EREN Use the Device Manager to change the properties 1 Open the Windows control panel go to the System Properties dialog box and select the Hardware tab Divers Driver Signing lets you make sure that installed drivers are compatible with Windows Windows Update lets you set up how Wind
13. the Up To check the calibration values open the Platform and Down buttons to raise or lower the platform as needed Calibrate option in the 3D Print menu Calibration Up WWE values are in the middle section of that window Down Set nozzle height 132 88 2 Enter the distance from nozzle to platform at each of the 9 points 1 0 2 v 25 0 1 v 30 1 NOTE If the Platform Calibrate window doesn t open 40 11 s lo 0 6 0 0 Mac or any of the values are left empty PC nae CEN qune the platform is out of level by more than 0 9mm OEE ey LIENS dami at one or more points You will need to manually level the platform before running the Platform Calibration again see page 14 _ Apply current values Reset Quit 15 Afinia H800 3D Printer User s Manual Manual Platform Calibration Select Platform Calibrate from the 3D Print menu Click the button labeled 5 to move the nozzle to the center of the platform Use the Up button to raise the platform Hold the button down to move the platform steadily or use single clicks to fine tune the platform height If you are using clips to secure the print surface to the platform be careful to position the clips so they do not interfere with the nozzle or wind barrier Raise the platform until the print surface is just touching the nozzle and note the current height Click the Down button a few times to lower the platform and check the other 8 calibration points
14. the part in Normal Fast or Turbo mode e f printing multiple parts at once reduce the number of parts that are being printed Changing Filament while printing If you need to change the filament during printing Double Press the Play button on the control panel When paused Double Press the Filament button to remove the current filament After changing filaments insert the new filament and Long Press the Filament button to load your new filament If you are changing colors you may need to extrude a few times to remove the last of the previous filament color Keep the extruded filament string connected to the nozzle pull it from the nozzle just before the nozzle contacts the print surface after resuming the print by Double Pressing the Play button again this helps keep stray strands from sticking to your model Model Creation What does Manifold mean For any model to print correctly it should be a manifold object What this means is as simply as possible is that each edge must be in contact with two and only two surfaces Most design software will allow you to create non manifold objects which can result in print problems The most common way for a model to become non manifold is when several objects are joined together creating surfaces in the model that are in contact with or crossing through each other Fix in the Edit menu of the Afinia 3D software may repair the non manifold problem areas but the best solution is t
15. to work properly at an ambient temperature of between 60 F and 85 F and humidity of between 20 and 50 Operating outside these limits may result in low quality models Afinia H800 3D Printer User s Manual Overview The Afinia H800 was designed specifically for educators and professionals looking for fast hassle free 3D printing with exceptional quality The Afinia H800 boasts a host of features from Smart Support user friendly software and automatic leveling to paper thin layer HD resolution with a heated build platform Everything about this printer is geared towards creating high standard professional 3D models Print a working bearing in one design make a part for a dishwasher or just unleash your creativity and bring your designs to life with your new Afinia H800 One Button Filament Change out 100 Micron High Definition Detail Smart Support Technology Large 10 x 8 x 8 Build Platform Easy Filament HEPA Air Replacement Filtration System Fully Automated Calibration 51dB Quiet and Fast The Afinia 3D software sends the print data from a Mac or PC to the Printer over a single USB cable The Extruder delivers the Filament from the Spool into the Nozzle which heats the filament to printing temperature and deposits it on the Platform Afinia H800 3D Printer User s Manual The Afinia H800 with HEPA filter is packed with advanced technologies in a stylish and robust design Control buttons
16. AFINIA3D H800 3D Printer Version 1 2 Afinia H800 3D Printer User s Manual Afinia H800 3D Printer User s Manual TABLE OF CONTENTS Salety PIOCAULUONS sui E Baer EDR o CZ aaa 5 Protecting tne Printer acid OKE elk awk kika dw ch ck 5 BRI n 6 Whipackine the Alinia H800 SD Printe os eis eh sib lev er e a o vo i eed ev 8 ThePrpnt Hedgd iaceo mop O O ani as contu eder da da 9 PHS Control BUTTONS scare D kz i kad ka OO At 9 Installing the Afinia H800 3D Printer leeeseeeeeeeeee eese ne enne nennen 10 BDIWeEro asSotwareSta AL ON ania Cres no einsam nea oc a Ceca e Ebo edv uen tax ont edm ett Cuna loe aat 10 Staliet E PIDE oss doe O O ER dios Czad ES 10 Eosding the FIISEnS DIE a o A Alo m raus sentem do O sA 11 GEMNG Ready CO iul A H 12 Starting the Afinia 3D Progra M arenei oO EE vp eta qve pl Ute esaet uetales ede i eta du t p en bea 12 Initializing the PEIBEGE ooi vere Eon P Uno IAN FON A es does ER dU NU Ede pes UA Re Tees P Ue dl Un Qu EEUU ped 12 PEED AUIS tne PAU OG w RE DO tm 13 ksyvelnSThE Prine PISO ij ann O O a a na Olafa 14 PISUGTM CALIBIALNON sacz aoi ad OGR OE O GRE E AAAA 15 Automatic Plator Cala OM ico WG R AO A 15 Manual Platform Calibra Ol adko GE Eos GG Ok doi OK 16 Calibrating the Nozzle Height cierna enai NE E a E E OE AEEA 17 Other Maintenance OPUONS wawa wra adi w da 18
17. All materials expand when heated and shrink when cooled The larger the part the worse the effect ABS is more prone to warping than PLA Air Printing When the printer is moving and acting as if it is printing but nothing is being extruded out of the nozzle Check the trouble shooting section for help 46
18. D Model Click File Open or the Open icon on the toolbar Windows only and select the model you want to open The Afinia 3D Printer software only supports STL files UP3 and UPP formats Mac Software Windows Software You can open several models and print them all at the same time see Placing Models onto the Build Platform page 24 Insert Copy Add multiple copies of the same model to the platform by selecting Insert Copy from the right click options Windows or by selecting Copy from the Tools menu Select the number of copies to add from the list You will need to reposition the models after the copies have been added Unloading the Model Windows Left click a model and then click Unload on the toolbar to remove the selected model You can also right click anywhere in the software window then choose Unload by the selected model name or Unload All models if you want to clear everything Unloading the Model Mac mper naan e B Bs Use either the Unload or Unload a All button in the right tool pane Click the Unload button to remove the currently selected model or Unload All to clear all models from the workspace Unload 260 00222 01 Unload All 20 Afinia H800 3D Printer User s Manual Note on STL files For a model to print correctly all the faces of the models need to have their normals facing outwards The Afinia H800 3D Printer software uses model color to show problems if any part of the model i
19. Dials under the platform arm to level the print platform Turning a dial clockwise will raise the platform above that dial Leveling Dials Always recalibrate the platform and nozzle height after leveling the Viewed from under platform platform The more level your platform is the better your print will be 14 Afinia H800 3D Printer User s Manual Platform Calibration Along with manual leveling the platform the Afinia software can run a Platform Calibration to adjust the printing of the raft laying down a level foundation for your model to be printed on This process is not intended to replace physically leveling the platform but to work with the leveling Note The Platform Calibration will only affect printing when using a raft If you are printing without a raft the Calibration is not used You can calibrate the platform automatically or manually Automatic Platform Calibration The automatic process will check the height of nine calibration points on the platform Select Auto Level from the 3D Print menu The differences in height between the nine calibration points are used to build up the raft to give your model a level foundation on which to print Afinia After the Calibration is complete the Nozzle Height will be automatically set Platform Calibration 1 Move platform to nozzle Move the platform using buttons 1 through 9 below to find the point on the platform that first contacts the nozzle Use
20. EE LO ROEE R e ia Oka 37 VERTICAL Call Ration GO EET N OGAE T 37 MPS amp ICK S ORA O KE a GE RC W OE WE A 39 Status NAIC ALOR A zacna cat awa ED DD 41 Changing Eanguag6es i ach kick iv Rr EY irak a cika 41 Updating the Printer RON iacu corn iue ic e stk a eoi ai a o acus oc aai a eU widnia 42 TFOUDICS MOO UING tee 42 DSDECIF CATIONS wawa wia GG ESC ei ea 45 Technical Suppor Gai ii BRE A n 46 Acronyms arnda Jargon zie Z alei sio Vois code o ovas du esu toe o GU za OLC dwa asd 46 Afinia H800 3D Printer User s Manual Afinia 1 Year Limited Warranty Below is the one year limited warranty included with this Afinia product Afinia prides itself on its outstanding product line and its technical support If for some reason your product fails Afinia a division of Microboards Technology LLC stands behind its warranties and assures you the best service possible in a quick and timely manner Afinia warrants to the original purchaser that this product is free from defects in material and workmanship Afinia will for one year at its option repair or replace at no charge for parts and labor from the date you purchased the product from an authorized Afinia reseller Nozzles and Cell Perf Boards are warranted for ninety 90 days e Warranty registration must be completed within 30 days of receipt of the product in order to validate the warranty Afinia a division of Microboards Technology LLC reserves the right to determine the val
21. H800 3D Printer User s Manual Option 2 Update the driver manually 1 Install the latest Afinia H800 3D Printer software Device Manager File Action View Help lt gt Bree A RH MB Processors lt gt SCSI and RAID controllers Sound video and game controllers 2 Find the 3DPrintQFreeMC IM Semas driver in the Device i Update Driver Manager dialog box it Hebe should be located in the USB TEn ME amp Standard Unive Uninstall section s Standard Unive Scan for hardware changes amp Standard Unive amp USB RootHub Properties l l amp USB Root Hub 3 Right click the entry and amp USB Root Hub select Update Driver USB Root Hub amp USB Root Hub Launches the Hardware Update Wizard for the selected device Found New Hardware Wizard 4 Select the Afinia H800 3D Please choose your search and installation options Driver folder the default is C P rogram 8 Search forthe best driver in these locations Files Afinia Afinia 3D Wise the check boxes below to limit or expand the default search which includes local paths and Printer Drive rs removable media The best diver found will be installed Search removable media floppy CD ROM Include this locaton in the search v 5 A Free Motion Card entry C Program Filestafinia Afinia 3D PrintertDrivers m should appear in the Device Don t search will choose the driver to install Manager list Choose this option to
22. PC directory on the installation disc Note This installs the Afinia 3D Printer software the Afinia 3D Printer drivers and the Afinia 3D Printer sample files into your Program files Afinia Afinia 3D Printer folder Follow the instructions in the Installer to be sure the drivers and software are all in place before attempting to use the Printer The instructions below will follow the same order as those in the Installer Installing the Printer Connect the power adapter as shown with the flat side out and turn on the power switch Long Press the Power button on the control panel to initialize the printer USB connection Connect the printer to your computer using the supplied USB cable The Printer will be recognized and automatically installed when it is connected to your PC or Mac 10 Afinia H800 3D Printer User s Manual Loading the Filament A Insert the end of filament into one end of the Filament tube which is on the upper right side of the spool holder B Feed the filament through the tube until about 4 inches of filament protrudes from the tube C Put the Filament Spool onto the holder with the end of the filament pointing up from the back D Feed the filament into the extruder head as far as it can go about 2 inches E Long Press the Filament button a If the filament doesn t start feeding when the printer beeps gently push in the filament F Replace the magnetic filament cover
23. R 4 Board once the printed model and raft have been removed Removal from Borofloat Glass After removing the glass from the printer platform allow the glass to cool completely As the glass cools you may hear cracking sounds this is the ABS film releasing from the glass If the model doesn t release from the surface of the glass spray a small amount of ammonia based window cleaner onto the surface of the glass near the edge of the model After a few moments the model should release You might need to reapply the ABS film to the glass after each print TIP Depending on the platform preparation method you are using the model may be easier to remove from the printer when it is still hot If you want to heat the platform before removing your model use the Table Heat option from the 3D Print menu CAUTION It is strongly recommended that you do not attempt to remove the model from the platform while the platform is still attached to the printer Doing so may damage the printer or affect the platform level and nozzle height calibration GLOVES It is recommended that gloves be worn as the platform may still be hot and to prevent injury from any tool being used to help remove the model from the platform 32 Afinia H800 3D Printer User s Manual Removing Support Material You will most likely need to remove any supports printed along with your model The support material is the same material as the model material but print
24. dm p lt aon B Shell For no fill select Shell Checking the Shell setting will reduce the material use and print time by not printing the fill material Some models may not be suited to printing with the Shell setting checked This will not affect the printed model s wall thickness or support material requirements Surface The Surface setting will print a model as a single layer outline of the model perimeter Note that this setting will not work with models having a base solid top or requiring any inner fill structure 26 Afinia H800 3D Printer User s Manual Support Settings Dense This sets how many layers of dense support material are printed directly beneath the model More layers of dense support makes for a more stable print but takes longer to print Non solid support 1 Angle Non solid support The Support Angle setting specifies the maximum Angle at which support material will be printed If the angle from horizontal is smaller than the selected setting the printer will add solid support layers under the part surface If the setting is 10 Deg only surfaces that are less than 10 degrees from horizontal will be given support Changing the value to 50 Deg will print support material to hold up surfaces that are less than 50 degrees from horizontal 45 Angle set to gt 50 500 Increasing this value adds more material and time to the print Decreasing this value may resul
25. e The Afinia 3D Software includes a feature that allows you to avoid most support material When specifying the Print Preferences select Only Base for the Support Area setting see page 27 28 Support material around the bottom of the model will still be generated but the amount of support material will be greatly reduced 39 Afinia H800 3D Printer User s Manual Tighten the Platform Screws Over time the screws holding the perf board to the platform may loosen Tighten them occasionally with the perf board installed but leave them loose enough to remove the board Shell Setting Tips The Shell option for the print Fill setting can be used to create truly hollow prints saving time and filament However not all models can be printed with this fill setting Models with relatively small horizontal or near horizontal surfaces are potential candidates for shell printing as these surfaces require little or no internal support to be successfully printed Remember each model is different you may need to experiment with each model to find out if it can be used with Shell printing Decrease print time where possible The faster you can print parts the less lifting from the platform you are likely to get Some ways to increase print quality include e f possible try to avoid printing large parts in solid mode e Set the layer resolution to as large a value as possible while still keeping the quality needed for the finished part e Print
26. e Auto Place option in the File menu to automatically position the model on the platform when the model file is opened By Hand Windows Press the Ctrl key and choose the target model by pressing and holding the left mouse button Move the mouse and drag the model to the desired position Using the Move button Click the Move button Windows or the Move parameter Mac on the toolbar choose or input the distance in the text box and then choose the axis for the direction in which you want to move NOTE When more than one model is open the gap between each model should be kept to at least 12mm to prevent the models sticking together or rafts from overlapping 24 Afinia H800 3D Printer User s Manual Print Setup Options Click the Setup option in the 3D Print menu or the Preferences button on the Print and Print Preview windows Setup sc sne7o002000 W m Z Resolution 0 15mm Fill MM Part Angle lt 45 Deg a Print Setup e Z Resolution 0 15 mm 7 t Part Fill Surface 3 C Shell C Surf goli ayers e urface Angle lt 45 Deg Solid Loose Support LS Yn pp Surface 3 Layers Hollow Big hole Dense 3 Layers v Angle lt 39peg jShell Surface Space js Lines Support Area gt 3 mm2 Dense 3 Layers Angle lt 30 Deg 7 Stable Other Space 8lines Area gt Smm2 Stable Support Printer Name My Printer Restore defaults Cancel OK
27. e Users user name Afinia Calibrate96 UP3 directory off the root of the main drive on Macs After the calibration model is printed remove the platform without removing the parts 37 Afinia H800 3D Printer User s Manual Calibrate XY 0 0 Deg XZ 0 0 Deg Open Calibrate from the 3D Print menu Measure the X1 and X2 length as shown in the pictures below IMPORTANT NOTE Before you enter any new calibration values the bar at the very top of the screen should read XY 0 00 deg XZ 0 00 deg If not click the Reset button Measure the calibration print from front left to rear right corners of the printed parts on the platform for the X1 measurement and the rear left to front right for the X2 measurement Do not include the raft or support material when taking these measurements Enter the X1 and X2 measurements into the labeled boxes Next carefully remove the Front Center L shaped component from the platform and check the inside angle If it is not 90 measure the exact distance in millimeters that the end of the long arm of the part needs to move to get the angle to be 90 enter that distance into the Z box If the angle is less than 90 the value to be put into the Z box will be positive If the angle is more than 90 the value will be negative For example if the end of the long arm is 1 3 mm above the surface enter 1 3 in the Z box Finally measure the long arm of the Front Center compone
28. ed at a lower density making it easier to remove and identify The left picture above shows the teapot with its support material still attached while the right picture shows the teapot with support material removed The support material can be removed using a number of tools and some can easily be removed by hand Wood carving chisels long nose pliers or wire cutters work well to remove support material GLOVES SAFETY GLASSES The support material and the tools are sharp Wear gloves and safety glasses when removing the part from the printer ALWAYS WEAR GLOVES AND SAFETY GLASSES WHEN REMOVING THE SUPPORT MATERIAL 33 Afinia H800 3D Printer User s Manual Maintenance Changing the Filament Changing the filament can be done either in the software or using the control panel 1 2 10 Remove the magnetic Spool Cover Select Maintenance from the 3D Print menu and click Withdraw or Double Press the Filament button Insert the end of filament into one end of the Filament tube which is on the upper right side of the spool holder Feed the filament through the tube until about 4 inches of filament protrudes from the tube Put the Filament Spool onto the holder with the end of the filament pointing up from the back Feed the filament into the extruder head as far as it can go about 2 inches Click Extrude in the Maintenance window or Long Press the Filament button If the filament doesn t start feedin
29. er Once you click this button the current model being printed is cancelled You CANNOT resume a print job once the printer has been stopped Pause Print This button will pause a print in mid progress while allowing you to resume the print job where it left off This is useful if you want to change the material color mid print or to allow fasteners to be inserted into printed cavities and then printed over to lock the fastener into place This option is only available when the printer is printing and above the first four printed layers Table Heat 1 hr Click the Table Heat 1 hr button to heat the table for a full hour to the correct temperature for the selected filament type The Status bar will show tte OO OOOO00000000 progress of the platform heating 0 50 100 Heating the platform will not take the full hour but the longer the platform heats the more the outer edges of the platform will be heated For prints extending close to the edge of the platform this will help prevent warping of the model during printing Note You should always preheat the platform prior to printing to ensure the best results Stop Preheat Windows Stop Heat Mac This button halts any heating of the table either the 1 hour heat or the 15 minute preheat from the 3D Print menu or control panel This option only appears when the table is being heated 19 Afinia H800 3D Printer User s Manual Printing with the H800 3D Printer Loading a 3
30. es or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Afinia H800 3D Printer User s Manual Safety Precautions Please read this section carefully before using the printer The printer can only be used with the power adapters supplied by this company or the product may be damaged with a risk of fire
31. g when the printer beeps gently push in the filament Replace the magnetic filament cover Printer Prepared for Printing Matrial ABS 217 New Spool If you are changing filament types click Extrude New Spool in the Maintenance window Material ABS gt select the filament type and enter the ZEM weight of the new spool a gj Weight 700 gram Center This must be done in the software not from the control panel TIP If you are loading a different color filament than the last spool run Extrude a few times before you start printing This will help remove any left over filament of the previous color CAUTION If the nozzle is blocked remove the nozzle and clean it GLOVES The extruder and platform are hot Use gloves when working in this area of printer 34 Afinia H800 3D Printer User s Manual Cleaning the Nozzle The outside of the nozzle can get covered with a layer of filament during regular use When the printer is printing this layer may melt on the nozzle and leave discolored spots in the model or even clog the nozzle To avoid this regularly clean the nozzle Click To Bottom in Maintenance and then click Extrude to heat the extruder and melt the coating of filament Wait until the filament is finished extruding then remove the extruded filament from the nozzle Use a heat resistant material such as 100 percent cotton cloth or soft paper and a pair of pliers With the material bet
32. ges rather than in the Print dialog Quality Options are Normal Fast Fine and Turbo which affects the speed at which the printer moves Generally the slower you print the better the quality of the parts For tall narrow parts running at Fast or Turbo speed can put down layers too fast if the last layer hasn t yet hardened the part may distort 29 Afinia H800 3D Printer User s Manual For large surface area parts the Fine setting will take longer to print and the corners of the raft may lift from the platform UnSolid Model Not all STL files are going to be perfect A perfect STL file is a fully enclosed surface with no gaps in the surface skin and no overlapping surfaces If your file is not perfect this option should allow you to print it anyway The software will auto detect models that may require this setting and check this option You can remove the check to de select this function if needed Thin Wall PC Only If your model has places where the thickness of the part is less than about 0 75mm this option will force the printer to include the wall when printing rather than potentially leaving it out This option is only available in the PC software at this time No Raft You can print without a Raft but it is not recommended The raft improves adhesion to the platform Also the Platform Calibrate feature see pages 15 16 is bypassed if the raft is not printed Heat Platform after finish Checking this option
33. idity of all warranty claims Warranty is void if the product serial number has been altered or removed Warranty is void if the product has been misused or damaged or if evidence is present that the product was altered modified or serviced by unauthorized service people The above stated warranty is exclusive and replaces all other warranties express of implied including those of merchantability and fitness for a particular purpose Afinia a division of Microboards Technology LLC will not be liable for any other damages or loss including incidental or consequential damages and loss of profits or revenues from whatever cause including breach of warranty or negligence This product has been thoroughly tested and inspected at the factory prior to shipment Nevertheless inspect your product completely for any damage or loss of parts that may have occurred during shipment Notify the delivering carrier promptly if damage claims are to be filed Afinia reserves the right to modify or update its product without obligation to replace any equipment delivered prior to any such change To register your warranty please visit www afinia com register FCC ID 026 H800 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Chang
34. ion To manually set the correct nozzle height 1 Open Maintenance from the 3D Print menu The current nozzle height is shown in the Maintenance dialog images below In the Windows example the platform is at the bottom of the printer the Mac example has the platform 135 5mm from the bottom Matrial ABS 217 g Total 4 14 Kg Heater Nozzle 25 3C withdraw New Spool Nozzle 118 2C Extrude Withdraw New Spool TE Platform 79 2C E 3 Table heat 1hr Stop All FL FR To 121 FL FR To 135 5 Stop All Center To Bottom Table heat 1hr Center To Bottom NL NR Set Nozzle Height Quit NL NR Set Nozzle Height Matrial ABS 250 g Total 4 11 Kg Status Quit J Windows version Mac version 2 Click the Center button 3 Raise the platform by entering a value into the To textbox and click the To button 4 Check the distance between the nozzle and the print surface If the platform is more than 0 2mm from the nozzle slowly raise the To value and click the To button each time Small changes will help avoid striking the print surface into the nozzle 17 Afinia H800 3D Printer User s Manual 5 Repeat until the print surface is 0 2mm from the nozzle about the thickness of a piece of paper folded in half 6 Check the nozzle height at all four corners of the platform If any of the corners is closer to the nozzle than the center u
35. ld be lubricated with lithium grease such as Mobil XHP 220 e For the Left to Right rails use lubricating oil such as Mobil SHC 630 When lubricating the bearings clean the rails as much as possible before applying new lubricant Slide the extruder several times in the all directions to spread the lubricant evenly If you have any questions about lubricating the rails please contact Technical Support see page 46 for contact information Changing the HEPA Filter We recommend changing the HEPA filter after 300 hours of printing M or 6 months whichever comes first 1 Rotate the filter cover counter clockwise to remove 2 Remove the old filter 3 Install the new filter in the guide brackets 4 Replace the filter cover and rotate clockwise to lock The HEPA filter should be replaced by a Class 7 or better filter Spare parts Some of the plastic parts on the printer can be printed by the Afinia H800 3D Printer itself If you need spare parts for your printer the files for the printable parts can be found in the C Program Files Afinia Example Spare Parts H800 folder on PCs and in the Afinia directory off the root of the current User directory on Macs Vertical Calibration The Vertical calibration procedure allows you to ensure that the printer platform is perfectly horizontal and that the printer prints consistently in the X Y and Z directions Open the file C Program Files Afinia Example Calibrate96 UP3 on PCs or in th
36. lk you through these steps 13 Afinia H800 3D Printer User s Manual Leveling the Print Platform Before calibrating the nozzle height check the vertical nozzle distance at each corner and center of the print platform Open Maintenance from the 3D Print menu and click the Center button ___ Matrial ABS 217 g Total 4 14 Kg Heater Matrial ABS 250 g Total 4 11 Kg Status gt zag Nozzle 25 3C Withdraw New Spool Nozzle 118 2C Extrude Withdraw New Spool Pom o Platform 79 2C Table heat 1hr MRSC i A am Nozzle 8 Platform Max 136 10 Cur 0 00 Nozzle amp Plataro Stop All z a on LER Tox 135 5 Stop All Center To Bottom Table heat 1hr Center To Bottom NL NR Set Nozzle Height Quit NL NR Set Nozzle Height 1 Quit Windows version Mac version If you know the nozzle height enter that height in the To box then click the To button If you don t know the nozzle height click the To button to bring the platform to the displayed height then slowly increase the height until the platform is about 0 2 mm from the nozzle clicking To after each increase Use the five position buttons to check that the platform at all four corners and the center are close to the same distance from the nozzle If the platform is not close to the same distance from the nozzle at all five points adjust the platform until it is as level as possible Use the 3 Leveling
37. mum of support material In many cases no support material other than that needed to support the base of the model will be used The 0 mm setting will create support material when the Angle setting is met no matter how small the surface area Printer Name PC Only Enter in a name for your printer This makes it easier to identify when you have more than one Afinia 3D Printer connected to your PC Other Settings Stable Support Stable support creates support that is more solid so the model is less likely to distort This can be useful where tall narrow support is needed TIP Setup and configuration settings except for the Nozzle Height Calibration and Platform Leveling are stored in the software not on the Afinia H800 3D Printer If you move the printer to another computer repeat the calibration and setup procedures 28 Afinia H800 3D Printer User s Manual Printing TIP Two keys to successful printing on the Afinia H800 3D Printer are platform preparation and preheating The best results will be achieved if e he platform has been leveled and calibrated e The nozzle height is correctly set e The printer is in a room that is warmer than 65 F and free of drafts e The platform is very well preheated Click Table Preheat 15 mins in the 3D Print menu or Short Press the Filament Button on the panel Click Table Heat 1 hr in the Maintenance window to preheat the platform for one hour When printing with ABS let the platform hea
38. nt from the inside of the angle to the end which should be 40mm Enter the exact measured value into the H box of the Calibrate dialog box Click OK to record all these values and exit the calibration 38 Afinia H800 3D Printer User s Manual Tips 6 Tricks Preheat the platform before printing Large parts can sometimes have corners lift from the platform which causes the part to distort Preheating the platform see page 29 to at least 90 C when printing with ABS is a step you don t want to miss Having the platform heated before print starts helps keep the model adhered to the platform during printing Monitor the platform temperature in the Maintenance window Level Platform and Correct Nozzle Height Two keys to successful printing and removal of the print raft is to make sure the platform is level and that the nozzle height is set correctly Use the Maintenance window to bring the nozzle close to the print surface manually level the platform as much as possible then run the Platform Calibration or Auto Level utilities to calibrate the platform and set the nozzle height see pages 15 18 Be sure to use the calibration utility to build a flat raft surface right below your model Position the parts as close to the center of the platform as possible The center of the platform is where the heating is most regulated which helps to keep the support raft adhered to the platform Try to avoid printing any object near the edges
39. o correct problems in your design software Many software packages can check for and repair non manifold models consult the documentation for your software Model Creation What does Surface Normalization mean The outer layer of every 3D printed object is actually composed of an outer surface and an inner surface Surface Normalization means these surfaces are pointing the correct way If you have an outer surface buried inside your model or have an inner surface on the outside of the model you will need to normalize the surfaces The most common reason for non normalized surfaces is when two surfaces cross each other Fix in the Edit menu of the Afinia 3D software may resolve the surface problems but the best solution is to correct the problem in your design software Many software packages can check for and remove non normalized surfaces consult the documentation for your software 40 Afinia H800 3D Printer User s Manual Status Indicator The table below explains what each Status Indicator state means STATUS DISPLAY Yellow Printer switched on Pulsing waiting to be initialized Green Printer initialized Pulsing waiting for job Blue Letter Fast Print job spooling Rotation Slow Printing Blue Pulsing Red Pulsing Error Single letter remains on L sp CARD ERROR PLATFORM TEMPERATURE ERROR Printing Paused PRINT HEAD TEMPERATURE ERROR MOTION SYSTEM ERROR PRINT HEAD ERROR 00000000000000
40. of the platform Model Orientation Tips Generally follow these three simple tips on model orientation for better print results a Position the model so the largest flat surface is on the bottom b If your model has any cylindrical parts either solid or holes position them so they are vertical c Minimize support material by orienting the model with as many concave surfaces up as possible Remember these orientation tips may not apply to all models Each model is unique and has its own best orientation for printing Scaling your Model Not only can the Afinia 3D software scale your model in all three dimensions you can use the Scale function to change the size in any one of the three dimensions independently For instance you can make your model taller by setting the scale factor and clicking just the Z Axis button without affecting the width or depth see page 23 Minimum Model Cross Section Due to the width of the extruded filament models with portions that have a horizontal cross section of smaller than 0 8mm to 1 0mm may have missing print areas Merging and Rafts Positioning multiple models too closely in the software can result in overlapping rafts leading to print failure Use Merge in the Edit menu before printing to have the software eliminate that problem by creating a single raft instead of several Be sure to save these merged models if you will be regularly printing them as a group Minimal Support Material Us
41. ol If you are using a 500g spool of Afinia Premium Plus ABS filament divide the cost of the spool by 500g to get the cost per gram of material The Fill and Support settings affect the amount of filament used more than anything else Say you are printing a cube measuring 30mm x 30mm x 30mm with a layer thickness of 0 15mm The amounts of material will be used for each of the four Fill settings would be PC Fill Setting Mac Fill Setting Fill Percentage Weight of Model a 3 Gm 2 tag e m sig ewe m oaz Note Shell and Surface fill settings results are not shown The cube printed at the lowest density will be about half the cost of printing it at the highest but this may not apply to all models each model will have a different ratio of surface to infill Run a Print Preview to calculate the printing costs of any given model TIP Once the print has started you can disconnect the USB cable to printer The print job is stored in the printer s internal memory so the computer is no longer required Most actions can be done using the button panel on the computer pause printing for instance but you will need to reconnect the printer to see the exact layer being printed or the nozzle and platform temperatures Save as Project Once your model is on the platform and the print settings the way you want them you can Save as Project option under the 3D Print menu to create a 3D print project All of the settings wi
42. ows connects to Windows Update for drivers Driver Signing Windows Update 2 Click the Device Manager button to open the following dialog Tay box Find the 3DPrinter FreeMC in the USB section Eo oco a E Hardware Profiles 3 Click the right mouse button and select the Uninstall option The confirm dialog box will appear Click OK Doae forge SE 4 Install the latest Afinia H800 3D software ZACIECECIGT 58 Processors 5 Unplug the USB cable then plug it back in Windows sepes Sound video and game controllers will find a new device Manually select the driver folder 25 7 7 the default location is C Program Files Afinia Afinia ECL 3 D P ri n te n D ri vers i amp Standard Universal PCI to USB Host Controller 3DPrint FreemMc Standard Enhanced PCI to USB Host Controller amp Standard Universal PCI to USB Host Controller amp Standard Universal PCI to USB Host Controller amp Standard Universal PCI to USB Host Controller amp USB Root Hub amp USB Root Hub amp USB Root Hub amp USB Root Hub amp USB Root Hub A Device Manager File Acton View Help 5 8 WWW FA6FA301602 6 There should now be a new amp Computer driver section in the device swe Disk drives manager as shown to the en DVD CD ROM drives Floppy disk controllers Free Motion Card 3 3D Printer FreeMotion me IDE ATA ATAPI controllers dal Infrared devices e Keyboards right 43 Afinia
43. s Reset Quit In the example above the print surface is slightly warped with the center higher than both the front and back edges The manual leveling process would not be able to account for the warp but the Platform Calibration can 16 Afinia H800 3D Printer User s Manual Calibrating the Nozzle Height This section is one of the most important of the entire manual Please read it carefully to help you understand the nozzle height setup procedure To print successfully the platform should be 0 2mm from the nozzle As each printer is slightly different this distance needs to be calibrated before starting to print You can set the nozzle height either automatically or manually If you are using any print surface other than the supplied FR 4 Perf Board you will need to set the Nozzle Height manually Automatic Nozzle Height Calibration The Automatic Nozzle Height Calibration process will only work with the supplied FR 4 perf board as the print surface If you are using any other surface or the perf board with Build Tak or any other surface adhered to the board manually set the nozzle height Afinia Select Nozzle Height Detect from the 3D Print menu The extruder will move to the back left of the printer and the platform will lift until the nozzle contacts the Nozzle Sensor The detected nozzle height will then be displayed Click OK to close the window and your nozzle height is set Manual Nozzle Height Calibrat
44. s red the normals are facing the wrong direction in that place See page 40 for more information on Surface Normals and Model Manifold requirements Fixing STL Files The Afinia 3D Printer software includes a Fix option that will try to fix any bad surfaces in your model Under the Edit menu in Windows you will see Fix and under the Tools menu in Mac will be the Autofix option Select the model and click Fix or Autofix to attempt a repair of the bad surfaces Saving the model Choose the model and select Save from the File menu The file is saved in UP3 format with the file size being 13 18 of the original STL file size This is a convenient format for users to archive or transfer files Saving the model as a project Choose the model and select Save As Project from the File menu All of the settings within the Setup or Preferences will be saved as well as the Quality and No Raft settings The settings that are not saved within a project include the Nozzle Height UnSolid Model Heat platform after finish and Pause at settings The project file is saved with an extension of UPP This file can be copied to other locations or computers without needing to include the original STL file or files Merging Models If you have loaded more than one part onto the Multiple parts platform combine them into a single print by Mac Software using Merge from the Edit menu in Windows or the Tools menu in Mac Open all the models yo
45. se that point to set the height 7 With the print surface 0 2mm from the nozzle click the Set Nozzle Height button to save the current nozzle height If you haven t manually re leveled the platform since the last time the Auto Level was run you can stop here If you have manually leveled the platform follow the next 4 steps 8 Take note of the nozzle height you may need to reset the height when you run the Auto Level feature again 9 Select Auto Level from the 3D Print menu 10 After the Auto Level finishes the automatic Nozzle Height detection will be run again 11 Once that is complete go back into the Maintenance window set To to the value from step 7 and click the Set Nozzle Height button TIP If the print surface contacts the nozzle while making height adjustments re initialize the printer and before undertaking any other operations Other Maintenance Options Extrude heats the nozzle and loads material into the nozzle When the temperature is high enough the material is squeezed out of the nozzle The printer beeps before material starts extruding and it beeps again when finished Withdraw clears the filament from the nozzle when you change the filament or if the nozzle needs to be cleaned When the nozzle is up to temperature and the printer beeps gently pull out the material New Spool is used by the software to keep track of how much material has been used on the spool and will warn you if you don t ha
46. select the device driver from a list Windows does not guarantee that the driver vou choose will be the best match for your hardware R 44 Afinia H800 3D Printer User s Manual Specifications Printer Physical Characteristics Printer Weight 42 Ibs 19 KG Net 60 Ibs 27 KG Gross Printer Size 19 5 x 19 5 x 20 5 In 495 x 495 x 520 mm Power Requirements 100 240 VAC 50 60 Hz 220W Specifications a PC Intel Core 2 Duo or equivalent Minimum Processor Mac Intel based only PC 32 bit Win XP Vista 7 8 PC 64 bit Win Vista 7 8 Mac Intel based OS 10 6 10 10 Environmental specifications Ambient temperature 60 F 85 F Operating System Compatibility Relative humidity 20 5090 45 Afinia H800 3D Printer User s Manual Technical Support For technical questions or support issues contact Afinia Technical Support PH 952 279 2643 support afinia com www afinia com Please have the Model and Serial Number of your Afinia H800 3D Printer available when contacting Technical Support Date of Purchase Place Purchased Serial Number Located on back of Printer Acronyms and Jargon STL Additive Fabrication STereoLithography is the common file format used for sharing and printing 3d files The technical term used for the more user friendly term of 3D printing ABS Acrylonitrile Butadiene Styrene is a lightweight thermoplastic with resistance to high heat and is the most
47. t in poor printing of overhanging surfaces There is a balance between minimizing the amount of support material and maintaining the quality of the part as well as minimizing the difficulty of removing support material The orientation of the part on the print platform also determines how much support material is printed and how difficult the support Angle set to gt 10 49o material will be to remove Support Material Bulle Material As a general rule it is easier to remove support material from the outside of a part than from the inside In the picture to the right the part would use a lot more support material if printed with the opening facing down than if it were facing up Space Space sets the distance between the lines of support material Changing this value will change how the support material is printed removal of support material and print quality can be affected Only advanced users should change the Space setting 27 Afinia H800 3D Printer User s Manual Area This setting specifies the surface area above which support a WE isa mp material is printed Choose 5 mm and there will be no support a if the overhanging area is less than 5mm Lower values in this setting can save time and filament but the stability of the part during printing can be reduced Two special options for the Support Area setting are also available The Only Base setting will use a mini
48. t to at least 90 C before sending the print Maintenance in the 3D Print menu displays the platform and nozzle temperatures Click Print in the 3D Print menu Printer 3D Printer Printer H480 90004149 Preference v Preferences Printer My Printer H800 70002000 __ Preferences Rom Ver 6 09 Firmmare 3 06 Status Preview Layer thick 0 15 mm Fill Solid Opti 0 15 L Fill Nozzle Material ABS ptions 0 15mm Loose Fi m ki 211 71 Material ABS Height Nozzle Height 132 5 Options Options Quality Normal v Unsolid Model 7 OK UnSolid Model Quality Normal Heat platform No Raft Thin wall after finish No Cancel No raft Heat platform No z Pause at after finish Enter the heights to pause separated by commas Pause at e g 7 6 13 38 2 Enter the heights mm to pause separated by commas e g 7 6 13 38 2 The software sends instructions for printing each layer of the model to the printer When that is complete the material usage and estimated print time is 4 displayed Finish 06 Friday 15 35 The USB connection to the printer can be unplugged at this point Print Options Nozzle Height You can make changes to the Nozzle Height using this setting for the current print only but it is not recommended unless you know that the value you are entering is correct It is recommended that you use the Calibrate Nozzle Height process as listed on page 17 to make any chan
49. the Z axis only 1 Click Scale a 1 Select the Scale option 2 Input 1 2 in the text box 2 Input 1 2 in the text box 3 Click the Z Axis button 3 Click the Z button Example 3 Scaling to convert inches to mm 23 Afinia H800 3D Printer User s Manual Occasionally an stl file may appear much smaller or much larger than designed This is due to the design software saving the units of measure as inches rather than millimeters the Afinia 3D software uses millimeters only so a 1 inch model would appear as 1 millimeter This is simple to resolve with these steps Click Scale Select the Scale option Select or input 25 4 in E Input 25 4 in the text box 1883307 E 3 Click the Scale Scale Click the Scale button button If the model initially appears much too large convert the size from millimeters to inches by selecting PC only or entering 0 03937 into the text box and clicking the Scale button This does not actually change the model s measurements just scales it in the software Placing Models onto the Build Platform Where you put your models on the platform can affect print quality TIP In general try to place your model in the center of the platform Auto Place Click Auto Place on the far right of the toolbar to center the model on the platform or arrange multiple models When there is more than one model on the platform using Auto Place is recommended Windows TIP Check th
50. thin the Setup or Preferences will be saved as well as the Quality and No Raft settings Settings that are not saved in a project include the Nozzle Height UnSolid Model Heat platform after finish and Pause at settings The project file will be saved with an extension of UPP This file can be copied to other locations or computers without needing to include the original STL file or files 31 Afinia H800 3D Printer User s Manual Model Removal You should never attempt to remove the finished model from the print surface while it is still in the printer Doing so may affect the platform leveling or bend the entire platform assembly so that it is no longer perpendicular to the printer head Use gloves when removing the print surface and model from the printer as the print surface and model may still be hot The gloves will also protect your hands from any tools being used to release the model from the print surface If you are using the Perf board press the front corners slightly and pull the board forward to release it If you are using any method that clips another surface to the printer platform simply remove the clips holding the surface to the platform and remove the entire print surface Removal from FR 4 Perf Board Gently slide the supplied putty knife under the model and slowly wiggle it back and forth to lift the support material from the print surface Be sure to clean any remaining material from both sides of the F
51. u want to merge arrange them the way you want on the platform and click the Merge option If you save the file all the components will be saved as a single UP3 file 21 Afinia H800 3D Printer User s Manual View Options The mouse can be used to rotate pan or zoom the view of the models Rotate Press the middle mouse button and move the mouse to rotate the view Pan Press Ctrl and the middle mouse button at the same time and move the mouse to pan You can also use the arrow keys to pan the view Scale Rotate the mouse wheel The view will zoom in or out View The system has eight preset standard views the default view being Fit Click View on the toolbar Hide Toolbar X 38T Customize Toolbar Windows or the View menu to select the View Animate options Top iA The caption under the View button will show the Bottom Bottom selected view name Front Front Back Left Right ISO Back Left RI g ht 150 Windows version Mac version Model transformations Models can be moved rotated or scaled using the Edit menu or the toolbar v Move Parameter 9 Move 0 Scale Rotate Scale Auto Placement input BOJU Os Ou Move Rotate Scale Ml X Axis Axis O20 O50 Tranform 5 Windows version Moving the Model Click the Move button and choose or input into the text box the distance you want to move Then choose the axis direction in which you want to move Each time you click the
52. ve enough material left to print your model Click the button and enter the grams of material on the spool If it is a new spool enter the weight of the filament in grams Also select the filament type to set the nozzle and platform temperatures Printer Prepared RB Brandan Printer Prepared for Printing Layer 0 Matrial ABS 217 g Total 4 14 Kg Heater Matrial ABS 217 New Spool atti md Extrude 20 Extrude Material ABS Y Material ABS Nozzle 8 Platfornj Nozzle amp Plataro FL Weight 700 Center NL Quit Windows version Mac version 18 Afinia H800 3D Printer User s Manual TIP An empty Afinia Premium spool weighs about 280 grams If you are installing a partially used Afinia Premium filament spool weigh it and subtract 280 grams from the weight Enter that value into the material Weight text box Status This area displays the current temperature of the nozzle and platform and if either element is currently being heated Nozzle amp Platform Position Controls The five buttons FL FR Center NL NR control the position of the nozzle and the platform The To button controls the height of the platform and is used in the manual nozzle height calibration procedure described on page 17 Bottom returns the platform to the lowest position Set Nozzle Height Uses the value in the To box and saves it as the Nozzle Height Stop All Stops heating and all the movement of the print
53. ween the pliers and the nozzle apply gentle pressure and turn the pliers to remove the filament material Do not apply heavy pressure Remember the nozzle can heat up to 260 C 500 F that s over two and a half times the boiling point of water Do not touch the nozzle or nozzle mount with bare skin If this does not clear up any issues remove and soak the nozzle in acetone overnight to remove excess ABS material from the nozzle Ultrasonic cleaning baths also work Removing Changing the Nozzle If the nozzle becomes blocked you will need to remove the nozzle in order to unblock or replace it Lower the platform to the bottom Click the Withdraw button on the Printer or Maintenance dialog box to remove the filament from the nozzle Once the Withdraw has completed and before the heater has a chance to cool below 200 C use the nozzle wrench provided in the toolkit to remove the nozzle Use the same process to replace the nozzle being sure to heat the extruder to at least 200 C before tightening the nozzle back down Do not apply too much torque to the nozzle to avoid twisting the heater assembly 35 Afinia H800 3D Printer User s Manual Cleaning the Extruder Gear The gear in the extruder may occasionally need cleaning to keep the filament feeding smoothly 10 11 12 13 14 15 16 Long Press the Initialize button on the Control Panel to put the printer in sleep mode Turn off the power s
54. witch on the back of the printer Lift the Cable Cover from the top of the Print Head Disconnect the Ribbon Cable from the Print Head Disconnect the fan Slide the Print Head Cover off the Extruder Motor Remove the two screws on the Extruder Gear Cover and remove Cover Clean any filament debris from the teeth of the Extruder Gear Replace the Extruder Gear Cover and screws Replace the Print Head Cover Slide it into place until the Cover clicks Reconnect the fan Replace the Print Head into the Print Head mount making sure all three magnets are secure Reconnect the Ribbon Cable Replace the Cable Cover Turn on power and Long Press the Initialize button 36 Afinia H800 3D Printer User s Manual Cleaning the Platform Regardless of your method of preparing the platform a smooth surface will improve your results e f you are using the FR 4 Board as the print surface you should remove any remaining filament material from both sides of the board before printing again e f you are using blue painter s kapton or other type of tape on the platform replace the tape once it becomes uneven Remove excess adhesive from the platform before replacing the tape Lubrication of Extruder Rails The extruder rails on the Afinia H800 3D Printer requires lubrication every 4 6 months to keep it operating smoothly Different lubricants are required for the two rail bearing types e he Front to Back rails shou
55. y slight downward pressure on the two spring bearings when sliding the perf board back into place The heads of all 13 mounting screws will lock down the board when installed correctly 20 0 0 65 O Unlocked Locked Borofloat Glass Many people use Borofloat glass as the print surface brushed with an ABS acetone slurry and allowed to dry into a thin ABS film The ABS film will hold the model to the glass and release from the glass as the glass cools If the model does not easily release spray a small amount of ammonia based glass cleaner around the model The same glass cleaner can be used to clean the film from the glass It is recommended that you clean and recoat the print surface after each print The Borofloat glass can be placed directly on top of the installed perf board or on the platform screws Use office clips to hold the glass in place BuildTak Print Surface BuildTak is a print surface that self adheres to the Perf board or to glass If adhering to glass be sure that no air is trapped between the glass and the BuildTak Position the BuildTak surface on the actual print zone the Perf board is larger than the surface with the perimeter outside of the print zone Borofloat glass and BuildTak are available at store afinia com Whichever platform preparation method you use having a well leveled platform a correctly set nozzle height and a pre heated print surface will improve your results The next few pages wa
Download Pdf Manuals
Related Search