User Manual - Comkit Online
Contents
1. The wiring diagram is stuck on the front counterpanel of the appliance In order to gain access thereto unplug the appliance from the power source loosen the screws holding the front panel and slide it away after first opening the door 3 ADVICE ABOUT TRANSPORTATION The net weight and the weight including packaging of the appliance are given on the cover of this instruction manual Please refer to the instructions on the packaging in order to correctly transport and lift the appliance To prevent the oil in the compressor from flowing back into the coolant circuit always make sure that the appliance is kept upright during transport storage and handling Follow the instructions given on the packaging The appliance must be installed by authorized personnel in compliance with the current laws in force and the Manufacturer s instructions Once you have removed the packaging according to the instructions on the box MAKE SURE THAT THE APPLIANCE IS IN A PERFECTLY GOOD CONDITION IF IN DOUBT DO NOT USE IT AND IMMEDIATELY CONTACT THE DEALER who sold it to you All the packaging items plastic bags cardboard polystyrene foam nails etc must be removed and put out of the reach of children as they are potential sources of danger Rest the wooden pallet on the floor and using a hex socket wrench loosen and remove the bolts Fig 2 that fix the appliance to the pallet Lift the appliance using equipment fit to bear its weight Sep2. together with any ice present in the bin must be discarded Complete sanitizing can only be carried out only by the Authorized Technical Service Centres and must be done regularly depending on the conditions of use of the appliance the chemical and physical features of the water and after every period in which the appliance has remained at a standstill for any length of time You are advised to ask your dealer to draw up a scheduled maintenance contract that will cover the following e cleaning the condenser e cleaning the filter located on the water supply solenoid valve e cleaning the ice tray e checking the charge of coolant gas e checking the operating cycle e sanitizing the appliance 10 PERIODS AT A STANDSTILL If you do not intend to use the appliance for a certain period of time proceed as follows e switch off the electric power source by means of the switch 7 in Fig 4 and remove the plug of the appliance from its socket e shut off the water supply by turning off the water supply tap 8 in Fig 4 e carry out all the operations envisaged for scheduled maintenance of the appliance see chapter 9 e clean filter of water supply solenoid valve as described in chapter 9 1 clean filter of air condenser if any as described in chapter 9 2
3. personnel in accordance with the Manufacturer s instructions e this appliance must be only be supplied with cold water for human consumption drinking water e the operating pressure must be between 0 1 and 0 6 MPa e atap must be installed between the water mains and the feed pipe of the appliance so that the water supply may be shut off if necessary e where the feed water is particularly hard you are advised to install a softener Any solid particles e g sand may be eliminated by installing a mechanical filter which must be periodically inspected and cleaned These devices must comply with the standards in force in the Country of use e never turn the water supply tap off when the appliance is working e only new hose sets supplied with the appliance are to be used to connect the appliance to water mains old hose sets should not be reused 5 3 a FILLING WITH WATER Fig 5 Insert the special seals provided 12 in the two threaded ring nuts 11 of the water supply pipe 9 supplied with the appliance Without exerting excessive force otherwise the unions could crack firmly tighten one of the threaded ring nuts on the outlet of the solenoid valve located in the rear of the appliance The other threaded ring nut must be screwed to the water tap 8 this too must be provided with a thread 5 3 b DRAIN Fig 5 Fix the water drain pipe 10 in the housing provided on the rear of the appliance Make sure that e the pipe is a hose t
4. the rear of the appliance and on the cover of this instruction manual 8 OPERATION The appliance is equipped with a thermostat in the ice bin which stops production when the ice accumulated in the bin reaches the probe to which the thermostat is connected When the ice is removed from the bin the thermostat will reactivate production thus creating a new stock of ice 9 MAINTENANCE 9 1 CLEANING THE FILTER OF WATER SUPPLY SOLENOID VALVE Fig 6 Fy at least every two months clean the filter 14 located on the water inlet solenoid valve proceeding as follows e switch off the electric power supply by means of the switch 7 in Fig 4 fitted during installation and disconnect the plug of the appliance from its socket e shut off the water supply by turning the tap 8 in Fig 4 fitted during installation unscrew the threaded ring nut 11 of the water feed hose located at the outlet of the solenoid valve at the rear of the appliance using a pair of pliers remove the filter 14 from its seat without damaging the water feed pipe connector e place the filter under a strong jet of water to remove residue but replace the filter if it is excessively dirty After having carried out the cleaning operations refit the filter and hose pipe taking the necessary precautions described earlier in the instruction manual When the operations have terminated turn on both the electricity supply and water supply 9 2 AIR COOLED MODELS Fig 7 Fo
5. 24480 ed 06 2012 AUTOMATIC ICE FLAKER INSTRUCTIONS AND WARNINGS Ce It is strictly forbidden to reproduce this instruction manual or any part thereof an MOP TINTOS LY B ON A Sy a os ax N Dear Customer congratulations on choosing a top quality product which is sure to live up to your expectations Please read this instruction manual carefully before using your new automatic ice flaker TABLE OF CONTENTS 1 IMPORTANT ADVICE AND RECOMMENDATIONS TECHNICAL SPECIFICATIONS ADVICE ABOUT TRANSPORTATION UNPACKING INSTALLATION 5 1 CONNECTION DIAGRAM 5 2 POSITIONING 5 3 CONNECTION TO WATER MAINS 5 3 a WATER SUPPLY 5 3 0 DRAIN 5 4 CONNECTION TO THE ELECTRICITY MAINS 6 START UP 6 1 CLEANING INTERNAL PARTS 6 2 START UP 7 MAIN CAUSES OF OPERATING FAILURE a bb Y N 8 OPERATION 9 MAINTENANCE 9 1 CLEANING THE FILTER OF WATER SUPPLY SOLENOID VALVE 9 2 AIR COOLED MODELS 9 3 CLEANING AND SANITIZING OPERATIONS 10 PERIODS AT A STANDSTILL The figures in this manual are of a general nature Some details may therefore differ depending on the specific model The Manufacturer declines all liability for any inaccuracies in this instruction manual due to printing or transcription errors The Manufacturer also reserves the right to make any modifications to the products that may be necessary or useful also in the interests of the user without impairing the products essentia
6. arate the appliance from the wooden pallet and fit the supplied feet into the housings on the base plate provided for the purpose 6 in Fig 3 Use a spirit level to ensure that the appliance is standing perfectly level If necessary adjust the feet 5 INSTALLATION 5 1 CONNECTION DIAGRAM Fig 4 7 electrical connection controlled by omnipolar circuit breaker with residual current device 8 water tap 9 water supply pipe 10 water drainage pipe 5 2 POSITIONING 8 The appliance must be installed in a hygienically clean location avoid premises such as cellars and storerooms because poor hygiene promotes the formation and proliferation of bacteria in the appliance The appliance can operate at an ambient temperature of between 10 C and 43 C The best performance will be obtained by installing the appliance in a place with an ambient temperature of between 10 C and 35 C and a water temperature of between 3 C and 25 C Avoid direct exposure to sunlight and do not install near heat sources m This appliance must be installed in a place where it can be supervised by skilled personnel must not be used outdoors e must not be installed in damp places or where it is liable to be sprayed with water e must not be cleaned with jets of water must be allowed a clearance of at least 5 cm all around 5 3 CONNECTION TO THE WATER MAINS w IMPORTANT e the appliance must be connected to the water mains by professionally qualified
7. d check that it is not crushed in any way e should the supply cable be damaged it must be replaced by a specialized technician using a special cable available from the Manufacturer or from the Technical Service Centres 6 START UP 6 1 CLEANING INTERNAL PARTS The appliance will have already been cleaned in the factory However you are advised to wash the internal parts again before using the appliance Make sure that the power supply cable is unplugged before carrying out the above cleaning operation See cleaning and sanitizing manual for information regarding cleaning operations Use ordinary washing up liquid or a water and vinegar solution for cleaning operations after cleaning rinse thoroughly with cold water and discard the ice produced during the first 30 minutes after cleaning together with any ice present in the bin It is advisable to avoid using abrasive detergents or powders since these might damage the finish 6 2 START UP Once the appliance has been correctly connected to the electricity mains water mains and water drain system it can be started up as follows a turn on the water supply tap 8 in Fig 4 b insert the plug in the socket and switch on the power supply by means of the relative switch fitted during the installation phase 7 in Fig 4 Switch on appliance by pressing the luminous switch 13 in Fig 3 7 MAIN CAUSES OF OPERATING FAILURE Should the appliance fail to produce ice before calling on the Aut
8. he internal diameter is 22 mm as required e the water drain hose is not throttled at any point throughout its length e the drain hose slopes downwards by at least 15 It is advisable to drain the water straight into an open drain trap 5 4 CONNECTION TO THE ELECTRICITY MAINS sa IMPORTANT e the appliance must be connected to the electricity mains by professionally qualified personnel in accordance with the Manufacturer s instructions e before connecting the appliance to the electricity mains make sure that the mains voltage rating corresponds to the value indicated on the rating plate e make sure that the appliance is connected to an efficient earthing system e make sure that the capacity of the power supply system suits the maximum power value indicated on the rating plate of the appliance e the appliance is supplied with a plug prepare a socket controlled by an omnipolar circuit breaker 7 in Fig 4 with a contact opening gap of not less than 3 mm in accordance with national safety standards currently in force This switch must be equipped with fuses with the associated residual current device positioned in such a way as to be readily accessible Insert the plug into the socket controlled by the switch 7 in Fig 4 e the plug must only be replaced by professionally qualified and authorized personnel and the new plug must comply with current national safety standards e make sure that you fully uncoil the power supply cable an
9. horized Technical Service Centre first check carefully that e the water supply tap 8 in Fig 4 fitted during the installation phase has been turned on e electric power is reaching the appliance the plug is properly inserted in the socket the switch 7 in Fig 4 is in the ON position and the push button 13 in Fig 3 is lighted up Furthermore e if there is excessive noise make sure that the appliance is not touching furniture or sheet metal which can give rise to noise or vibrations should any trace of water appear check the drain hole of the container to ensure that it is not clogged that the water fill and drain pipes are correctly connected and are not throttled or damaged make sure that the temperature of the air or water does not exceed the installation limit values see paragraph 5 2 make sure that the water inlet filter is not clogged see paragraph 9 1 If the fault still persists after the above inspections have been made turn off the electric power source by means of the switch fitted during the installation phase pull out the plug from its socket turn off the tap connecting the appliance to the water mains and contact the nearest Authorized Technical Service Centre To obtain a faster and more efficient reply when you call the Centre state the model of the appliance precisely together with its serial number or manufacturing number This information is given on the serial N plate Fig 1 affixed to
10. iance to be used by children incapable or inexperienced persons unless they are supervised or instructions have been issued about the use of the appliance by a person responsible for their safety e supervise children to ensure that they do not play with the appliance Should you decide to scrap appliance first disconnect the power cable from the mains and then cut the cable off In addition proceed as follows e break off and remove the door in order to prevent the possible danger of a child getting trapped inside do not allow the coolant gas and oil in the compressor to disperse into the environment e dispose of or recover the various materials according to the provisions established by the current laws in force in your Country This appliance does not contain coolant that damages the ozone layer This appliance contains fluorinated greenhouse gases covered by the Kyoto Protocol The Manufacturer shall not be liable for any damage to the environment animals persons or objects caused by incorrect installation 2 TECHNICAL DATA Fig 1 The voltage and frequency are given on the data plate on the appliance Refer to this data plate to check compliance Voltage 1 power 2 model 3 serial No 4 Manufacturer 5 The weighted equivalent continuous sound level A of this appliance is less than 70 dB A The measurements were taken 1 metre from the surface of the appliance and 1 60 metres above ground during ice production
11. ing poor operation may also cause serious damage to the appliance e ifthe appliance breaks down and or operates in a faulty way switch it off by means of the main switch fitted during the installation phase remove the plug from the socket and turn off the water tap Do not make any attempt to repair the appliance yourself Contact only professionally qualified and authorized personnel e in addition to rendering any form of warranty null and void modifying or attempting to modify this appliance is extremely dangerous e open and close the door carefully without slamming it do not use the ice bin to cool or store food or drinks because these operations could obstruct the drainage outlet causing the bin to fill up with water and overflow e inthe event of a failure contact the dealer who sold you the appliance he will be able to give you the address of your nearest Authorized Technical Service Centre Always insist on having original spare parts mounted e any specific information or diagrams regarding particular models will be attached to this instruction manual Fal Use of this electrical appliance requires compliance with certain fundamental rules in particular do not touch the appliance with wet or damp hands or feet e do not use the appliance when you are barefoot do not use extensions in premises such as bathrooms or shower rooms do not tug on the power supply cable to disconnect it from the mains do not allow the appl
12. l features of functionality and safety 1 IMPORTANT ADVICE AND RECOMMENDATIONS This instruction manual forms an integral part of the automatic ice flaker subsequently referred to as appliance and should be kept for future consultation In the event of the appliance being sold or transferred to another person this manual must be handed over to the new user in order to enable him to become familiar with the operation of the equipment and the corresponding advice and recommendations Before installing and using the appliance read the advice and recommendations contained in this instruction manual very carefully They are given in order to ensure safe installation use and maintenance of the appliance e always remove the plug from the power socket before proceeding with any cleaning or maintenance operations e to ensure the appliance operates efficiently and correctly it is essential to comply with the Manufacturer s instructions and to make sure that maintenance is performed by specially qualified personnel e donot remove any of the panels or grilles e donot rest objects on the appliance or in front of the ventilation grilles e always lift the appliance to move it even slightly Do not push or pull it e any use of the appliance other than the ice production using cold drinking water will be deemed improper e do not obstruct the ventilation and heat dissipation grilles since poor aeration in addition to reducing efficiency and caus
13. r air cooled models it is very important to keep the finned condenser and its external filter if any clean Have the finned condenser cleaned at least once every two months by an Authorized Technical Service Centre which can include this operation in the scheduled maintenance programme The external filter if any must be cleaned at least once a month as follows e switch off appliance and cut off power supply with the switch 7 in Fig 4 fitted at the installation stage open plastic grille e remove filter and keep it at a distance form the appliance e remove dust from filter by blowing with compressed air e replace filter in its seat and close plastic grille 9 3CLEANING AND SANITIZING OPERATIONS A cleaning and sanitizing kit specifically designed for this appliance is available from your dealer Do not use corrosive substances to remove limestone from the appliance because this will invalidate the warranty and may cause serious damage to the materials and components of the appliance Do not use jets of water to clean the appliance All cleaning operations must be carried out only after the electric power and water supplies have been disconnected as described previously by professionally qualified and authorized personnel Follow the instructions given in the cleaning and sanitizing manual supplied with the appliance IMPORTANT Allthe ice produced during the first 30 minutes after cleaning and sanitising operations
Download Pdf Manuals
Related Search