Home

D-Link DCS-5 0 User Manual - Dlinkddns.com

1. Security D Link DCS 5220 User Manual Wireless Setup This option can turn off the wireless function The camera server will detect the connection type when booting it will detect a wired connection first and then wireless If wireless is not connected during booting it will not detect again If wireless is disabled the camera will not detect wireless during booting Service Set Identifier is a name that identifies a wireless network Access Points and wireless clients attempting to connect to a specific WLAN Wireless Local Area Network must use the same SSID The default setting is dlink Click on the drop down list and select from the following options Infrastructure connecting the WLAN using an Access Point such as the DWL 2100AP or a DI 624 wireless router Ad Hoc wireless mode used when connecting directly to a computer equipped with a wireless adapter in a peer to peer environment In Infrastructure mode the wireless channel is automatically selected by the camera In Ad Hoc mode the default wireless channel setting is channel 6 Select the channel that is the same as the other wireless devices on your network select the transmission rate on the network Auto is the default setting Preamble Type Short or Long If your wireless network support Short Preamble then enabling it can boost overall throughput However if any wireless device does not support Short Preamble then it will not be able to commu
2. Click Next Select the program folder to install the application software Click Next D Link DCS 5220 User Manual InstallShield Wizard Choose Destination Location Select folder where Setup wall install files Setup will install IF surveillance in the following folder To install to this folder click Mest To install to a different folder click Browse and select another folder Destination Folder C Program Files 0 LinkSIP surveillance Browse H Cancel InstallShield Wizard Select Program Folder Please select a program folder Setup will add program icons to the Program Folder listed below You may type a new folder name or select one from the existing folders list Click Next to continue Program Folders D Link SIP surveilan ce Existing Folders lt Back Cancel 08 section 3 Configuration Click Next The installation is complete Click Finish D Link DCS 5220 User Manual InstallShield Wizard Start Copying Files Review settings before copying files setup has enough information to start copying the program tiles If you want to review or change any settings click Back If you are satished with the settings click Next to begin copying files Current Settings Setup Type Complete Target Folder C Program Files D Link MPF surveillance User Information Name D Link Camera Company D Link InstallShield Cancel InstallShield Wiz
3. Settings Minimize Click this button in order to minimize the playback program window Exit The playback program will be closed immediately when you click on the Exit button D Link DCS 5220 User Manual 106 section 3 Configuration Schedule Video Recording with Motion Detection To schedule video recording with motion detection you must first enable motion detection on the Internet Camera Click the Motion Detection button under the Advanced tab from the Configuration screen to access settings that affect how the DCS 5220 Internet Camera can serve as a security TSE device by recording only when motion is detected Note These settings can be configured in your Web eo ees browser and while logged into the IP surveillance rt of detection before cikg on the Next butt Cl Enable motion detec P F ogr am P Snapshot video or ICS 5220 TCP AV In this window follow the steps below to ensure that motion detection is correctly enabled 1 Check Enable motion detection 2 Click on New to have a new window to monitor video 3 Enter in a window name 4 Adjust the Sensitivity and Percentage levels according to the local environment The highest sensitivity and lowest percentage provides the most sensitive setting 5 After adding the motion window click on save to enable the activity display You can add up to 3 motion windows to trigger recording D Link DCS 5220 User Manual 107 secti
4. 2nd FTP remote folder D Link DCS 5220 User Manual Specify the Domain name or IP address of your second external FTP server This field is optional if you have already filled in the information for the first FTP server Specify the user name to access your backup FTP server Specify the user password to your backup FTP server Specify the destination folder on your external backup FTP server 93 section 3 Configuration For detailed information about each setting please refer to Configuration gt SETUP gt Mail amp FTP in the section titled Using the DCS 5220 With an Internet Browser page 26 Click the save settings button when finished Click the Schedule button under the SETUP tab and select snapshot to set the application settings for the DCS 5220 In this window follow the steps below to set the Schedule settings for snapshots to be recorded to an FIP site 6 Check the Enable snapshot box Select Weekly schedule and setup Time Select Motion Detection and check the motion window name in this case Moto Set the delay to take snapshots after event to capture the direction of the moving object Click Send snapshots by FTP and check FTP put Snapshots with date and time suffix Click the save settings button to save the settings SECURITY Setup FTP or Email notification based on motion or digital input triggering You can configure the dates and times that this schedule
5. Wireless technology as become so popular in recent years that almost everyone is using it whether it s for home office business D Link has a wireless solution for it Home e Gives everyone at home broadband access e Surf the web check email instant message and etc e Gets rid of the cables around the house e Simple and easy to use Small Office and Home Office e Stay on top of everything at home as you would at office e Remotely access your office network from home e Share Internet connection and printer with multiple computers e No need to dedicate office space Where is wireless used Wireless technology is expanding everywhere not just at home or office People like the freedom of mobility and it s becoming so popular that more and more public facilities now provide wireless access to attract people The wireless connection in public places is usually called hotspots D Link DCS 5220 User Manual 134 Appendix A Wireless Basics Using a D Link Cardbus Adapter with your laptop you can access the hotspot to connect to Internet from remote locations like Airports Hotels Coffee Shops Libraries Restaurants and Convention Centers Wireless network is easy to setup but if you re installing it for the first time it could be quite a task not knowing where to start That s why we ve put together a few setup steps and tips to help you through the process of setting up a wireless network Tips Here are a few things
6. IP camera name D Link DCS 5220 User Manual Password for the Administrators account The administrator password must be entered in twice for confirmation Create a new user for accessing the video image A maximum of twenty user accounts can be added The new user name will be displayed in the list of user names for deletion Administrator can edit or delete users here by selecting the user name Remove a user from the user list The name to identify your camera Text entered will be displayed in the black bar above the video window with a timestamp 44 section 3 Configuration Backup and Restore L Turn off the front panel LED Check this option to turn off the LED next to the lens This will prevent anyone from observing the operation of the Internet Camera SYSTEM SETTINGS Jevice Management SCRE SN Restore You can save and restore configuration restore factory settings restart the IP camera and set bid E ear une pee the Administrator timeout Bn rmware Upgate se g ogou Yo ia Ww Restore to Factory Default This option will reset the camera back to its factory default settings This will ae remove all the configuration settings that Restore To Factory were made previously Restore al settings to the factory defaut except settings n New REBOOT Reboot This option will restart the camera poten tho Doves ap Click Apply on this screen to restore the factory default settings After confirmation the
7. In the figure below Week time line is displayed It includes the time line schedule information and the selected day in the week Sun Marking Unmarking the Recording Time on the Week Time Line The corresponding changes for the markers on the week time line will be automatically added to the hour time lines which is shown above You can also mark and unmark the plotted bar by clicking and dragging with the left and the right mouse button Tue BG Ol Ge Os NOs OS Gee Or PGE Ss One S ee ees S 20 rel ee ee Hour Time Line In the figure below the Hour time line is displayed Oa Gt G2 Bs5 E be bee CS et esa eS e ie te iS 20 et 22 es D Link DCS 5220 User Manual 81 section 3 Configuration Marking Unmarking the Recording Time on the Hour Time Line You can apply the one click function by clicking the left mouse button and dragging to mark the time on this time line The operating method for the hour time line is the same as that of the week time lines Please refer to the previous section about marking unmarking on the week time line for more details Schedule with Time Picker Begin and End Time There are three controlling units in both Begin Time and End Time selectors shown below The first unit of these two selectors is the date picker You can select day with it to set the beginning time and the ending time for the recording interval The second and third units are the hour picker and the minute p
8. Installing a DCS 5220 Internet Camera on your network is an easy 4 step procedure 1 Assign a Local IP Address to Your Internet Camera 2 View the Internet Camera Using Your Internet Explorer Web Browser 3 Access the Router with Your Web Browser 4 Open Virtual Server Ports to Enable Remote Image Viewing This section is designed to walk you through the setup process for installing your camera behind a router and enable remote video viewing For the basic setup of the DCS 5220 follow the steps outlined in the Quick Installation Guide D Link DCS 5220 User Manual 113 section 4 Security After you have completed the setup of the DCS 5220 outlined in the Quick Installation Guide you will have an operating camera that has an assigned IP Address Because you are using a router to share the Internet with one or more PCs the IP Address assigned to the Internet Camera will be a local IP Address This allows viewing within your Local Area Network LAN until the router is configured to allow remote viewing of the camera over the Internet 1 Assign a Local IP Address to Your Camera Run the DCC program from the CD included with the DCS 5220 Follow the steps in the Quick Installation Guide to configure the DCS 5220 The camera will be assigned a local IP Address that allows it to be recognized by the router Write down this IP Address for future reference This is the IP Address assigned to your camera Write it down for later use 172 17 5 108 is on
9. and the port number that you gave your camera e g http 70 42 15 9 83 It is not necessary to enter the colon and port number if you are using the default Web server port 80 To access from a computer on your local home network simply enter the local IP Address of the Camera followed by a colon and the port number e g 192 168 0 120 83 If you are following this manual in the order it is presented you should now have an operating DCS 5220 Internet Camera configured with the Installer program This section of the manual will cover how to use the Internet Camera in two methods This section sh ion shows your camera s live video You can control your settings using the buttons below Current resolution is 640x480 e Using the DCS 5220 with an Internet browser and accessing the screens to control and monitor the camera e Using IP surveillance software with the DCS 5220 SECURITY D Link DCS 5220 User Manual 18 section 3 Configuration Using the DCS 5220 with an Internet Browser Open your Internet Explorer Web browser and enter the IP address for your Internet Camera http 192 168 0 120 In the example this address is 192 168 0 120 Your address may differ lf a window appears asking to install a Verisign certificate for authentication click Yes This allows the proprietary MPEG4 video stream to be recognized by Internet Explorer Internet Explorer Security Warning Do you want to install this software
10. if the router or firewall is properly configured for the ports the DCS 5220 is using Refer to page 124 for help in opening the correct ports on a router or firewall for use with the DCS 5220 Other possible problems might be due to the network cable Try replacing your network cable Test the network interface of the product by connecting a local computer to the unit utilizing a Ethernet crossover cable If the problem is not solved the Internet Camera might be faulty 11 Why does the Internet Camera work locally but not externally This might be caused by network firewall protection The firewall may need to have some settings changed in order for the Internet Camera to be accessible outside your local LAN Check with the Network Administrator for your network Make sure that the Internet Camera isn t conflicting with any Web server you may have running on your network The default router setting might be a possible reason Check that the configuration of the router settings allow the Internet Camera to be accessed outside your local LAN Please refer to page 124 for more information D Link DCS 5220 User Manual 130 section 5 Troubleshooting 12 connected the Internet Camera directly to a computer with a cross over cable Ethernet cable and received the following Windows error upon running the Installation Wizard This Windows error will occur if the Internet Camera is connected to a computer that is not bind sock failed X pr
11. 1 Product Overview Hardware Installation Connect an Ethernet cable to the Ethernet connector located on the Internet Camera s back panel and attach it to the network Note It is required that an Ethernet cable is used during initial setup Once your wireless configuration is set you may disconnect the Ethernet cable and begin communicating wirelessly with your DCS 5220 Attach the external power supply to the DC power input connector located on the Internet Camera s back panel labeled DC 12V and connect it to an AC power outlet D Link DCS 5220 User Manual Section 2 Installation Wireless Installation Considerations The D Link Wireless PT Internet Camera lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network Keep in mind however that the number thickness and location of walls ceilings or other objects that the wireless signals must pass through may limit the range Typical ranges vary depending on the types of materials and background RF radio frequency noise in your home or business The key to maximizing wireless range is to follow these basic guidelines 1 Keep the number of walls and ceilings between the D Link adapter and other network devices to a minimum each wall or ceiling can reduce your adapter s range from 3 90 feet 1 30 meters Position your devices so that the number of walls or ceilings is minimized 2 Be aware
12. Auto alarm in multiple modes Account password protection Multiple recording modes Event driven Scheduled and manual recording for each camera Just in time snapshot Motion detection with 3 alert windows for each camera D Link DCS 5220 User Manual 64 section 3 Configuration Application Layout and Functionalities This section demonstrates a global view of the monitor program shown below The components of the monitor tool will be introduced in detail in the following sections Misc Functions oa E woe 4 a Channel Area eow e e 6 So W 1 Tae SA 15 Layout Area a a T Hard Disk Status o s FresSagce ZEB S272 E Common Control Area ao vy rasp 1 Aer ida DI DO Control t de Ae E ie Cees a Ea F D a Ee be Ex Bim a E a Alert Message TEM lss D Link DCS 5220 User Manual Eiee yan in dea Bt li Pawei vorson3 J Video Area 65 section 3 Configuration There are several parts in the monitor tool Misc Functions Channel area Video area Layout area Hard disk status Common control area DI DO control Alert Message These include application exit minimization full screen monitoring lock stop alert and configuration menu for camera configurations global settings scheduler settings and the user information of this application software Tips for these operations are provided when you move the mouse cursor over each icon This area d
13. Configure for mobile viewing im Jate yf 4 ie San Ci l no i VIDEO SETTINGS Frame size Max frame rate Key frame interval Video quality control Fixed bit rate 512 Kbps v Fixed quality Good AUDIO SETTINGS O mute Aac Bit Rate 128Kbps GSM AMR Bit Rate 12 2Kbps x SECURITY 120 section 4 Security Play from RealPlayer The following steps are based on a Nokia 6630 cell phone Press the Menu button and select Media Select Open Select RealPlayer D Link DCS 5220 User Manual 121 section 4 Security Select Open When RealPlayer opens press Options D Link DCS 5220 User Manual 122 section 4 Security Select Download Select Video Clips Note 71 34 50 5 is the camera s IP address in this sample Press Options D Link DCS 5220 User Manual 123 section 4 Security Select Navigation Options Select Go to web address Input your rtsp address D Link DCS 5220 User Manual 124 section 4 Security Press Yes and allow Connection and Loading of the streaming video Enjoy streaming video on your cellphone D Link DCS 5220 User Manual 125 section 4 Security Play from PVPlayer Press the Menu button and select PVPlayer 7 o B3 D Link DCS 5220 User Manual section 4 Security Select Open location Input your rtsp address Note 71 34 50 5 is the camera s IP address in this sample D Li
14. Connection Setup Audio and Video Mail and FTP Th e M A N T N A N C a e S u S e d f O r G e rve r S ste m Motion Detection In this section you can setup the camera s Motion Detection settings If you are configuring this Ea p Q y mean Date device for the first time D Link recommends that you click the Setup Wizard button and follow PAG the instructions on screen If you wish to modify or configure the Motion Detection manually Man m al n t eC n a n C Schedule click manual setup to enable the Motion Detection setup E Motion Detection Setup Wizard Manual Motion Detection Setup The STATUS page will show the camera s status and logs The HELP page contains useful information about the setup and features of the DCS 5220 The Setup page provides the following configuration options Wizard Network Setup Wireless Setup Dynamic DNS Image Setup Audio and Video Mail and FTP Motion Detection Time and Date Schedule Access List Camera Control and Logout D Link DCS 5220 User Manual 22 section 3 Configuration Internet Connection Settings Internet Connection Setup Wizard Manual Internet Connection Setup Camera Motion Detection Settings Motion Detection Setup Wizard Manual Motion Detection Setup D Link DCS 5220 User Manual Wizard This section will help you to connect to Internet This wizard can help you set up the Internet connection step by step If you don t have enough inf
15. Mame RTSP MPEGS SP Control Publisher D Link Corporation More options Install Don t Install While Files From the Internet can be useful this File type can potentially harm vour computer Only install software From publishers you trust whats the risk D Link DCS 5220 User Manual 19 section 3 Configuration Client Setup Logout Pan Tilt Go to Pan Tilt Speed Auto Pan Stop Auto Patrol Snapshot Home Page Screen The image from the DCS 5220 should be visible from the device s Home page on your web browser Click on the Client Setup button to change settings related to the camera connection Click on the Logout button to logout from the camera server and close the browser Click the Pan Tilt button to control the camera s pan or tilt The Home button can move the camera to the preset home position Select from the preset drop down list to quickly move the camera to the desired preset position Please refer to camera control setup for the preset list function This can change the camera Pan Tilt speed Press this button and the camera will start to pan from left to right one time This will stop Auto Pan and Auto Patrol Click this button to quickly move the camera to the desired patrol setup according to preset positions Please refer to camera control setup for the preset list function Click on the Snapshot button to capture a snapshot image The image wil
16. WILL LICENSE THE SOFTWARE TO YOU ONLY IF YOU FIRST ACCEPT THE TERMS OF THIS AGREEMENT BY INSTALLING AND OR USING THE SOFTWARE YOU AGREE TO THESE TERMS IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT PROMPTLY RETURN THE UNUSED Do you accept all the terms of the preceding License Agreement IF you choose Mo the setup will close To install IP surveillance you must accept this agreement Installshield Click Yes D Link DCS 5220 User Manual 56 section 3 Configuration InstallShield Wizard Enter your User Name and Company Name information Customer Information Please enter your information User Mame Note This User Name is not the User Name to log into the IP qe D Link Camera surveillance program Company Hame D Link Install this application for f Anyone who uses this computer all users Only for me D Link Camera lt Back Cancel Click Next You must setup the administrator s password in order to proceed S Input and confirm your password in the window shown below Administrator Password Setup F e e x k k You must set admin password before you could use thie program Please type the password in the following Password Confirm lt Back Next gt Cancel Click Next D Link DCS 5220 User Manual 57 section 3 Configuration Select the installation directory for the IP surveillance software You can change the installation directory by clicking Browse
17. access to a wireless network based on a computer s hardware specific MAC address which is relatively simple to be sniffed out and stolen EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network WPA PSK WPA2 PSK uses a passphrase or key to authenticate your wireless connection The key is an alpha numeric password between 8 and 63 characters long The password can include symbols amp _ and spaces This key must be the exact same key entered on your wireless router or access point section 4 Security Setting Security At this point it is highly recommended that you click on the Configuration button on the Home screen and then Device Management the Tools tab to bring you to the Admin screen Enter a oe r ee access to the IP camera password for security purposes panardo ADMIN PASSWORD SETTING Password Retype Password Blank admin password will disable user authentication ADD USER User name To ensure the highest security and prevent unauthorized a use of the Internet Camera the Administrator has the exclusive privilege to access the System Administration TER settings to allow users entry and authorize privileges for all users The Internet Camera supports multi level IP camera name DCS 5220 password protection access to the Internet Camera that can be restricted to defined users who have a User Name and User Password wh
18. add the prefix to the video clip file name C FTP put viia cl wath diba ane bere sufi Video clip max file size This option sets the maximum file size for the video Oo E clip If you don t have enough upload bandwidth the SS video clip file will not complete uploading during the time interval and the upload file will not able to playback To avoid the problem please reduce the maximum file size or enlarge the time interval Motion detection This option enables motion detection triggering for video clip uploading D Link DCS 5220 User Manual 37 section 3 Configuration Detect Motion in Sequential Video Clip interval Email FTP FTP put video clip with date and time suffix Enable snapshot Weekly schedule Always From 00 00 to 00 00 Snapshot file name prefix Motion detection D Link DCS 5220 User Manual Check the motion detection window s to enable motion triggering The window s can be created in the Advanced gt Motion Detection page This option enables continuous Video Clip uploading The time interval for continuous Video Clip uploading This option enables the camera to send the Video Clip via e mail This enables the camera to send the Video Clip to a FTP server This option will add a date and time indicator to the snapshot file name For instance Video 20060102030405 jpg indicates that the Video Clip was captured at Year 2006 Month January Date 2nd Time 03 04
19. and recording Note The digital input output is not available for the DCS 5220 model This application software provides options for you to define the triggering criteria for the digital input of the camera The alert of the digital input can be defined as high level triggered or low level triggered Note The digital input output is not available for the DCS 5220 model Recording Settings Once the automatic video recording has been activated you can change this setting to regulate the recording of triggered events Recording will start from the specified number of seconds before the alert event has been invoked Recording will last for the specified number of seconds after the alert event has been invoked You can specify which media type you want to record Video Audio or both Changing the Camera Order in the List You can drag and drop in the grid area of the camera list to change the sequence of the connected Network Cameras which is shown below This will allow you to rearrange the cameras in an order of your choice Once the camera is moved to a specified location the proceeding cameras will then move 1 position up or 1 position down depending on which direction the selected camera was moved D Link DCS 5220 User Manual 12 section 3 Configuration Press and hold the left mouse button at the gray index field of the camera you would like to move ea Informatior Front Door 192 168 0 100 80 Drag the mouse t
20. applies as well as how the event is triggered and what function to perform when it is triggered Save Settings e Settings Don t Save Settings Save Don t Save Settings SNAPSHOT y J Selec edule to c DNS enable or Email mage Setup Audio and Video Even i Audio and Video S Enable snapshot ase r Mail anc input eguen n otion Detection shot WEEKLY SCHEDULE O sun O mon O Tue O Wed O Thu O fri CO Sat Time Always From 00 00 to 00 00 hh mm Snapshot file name prefix TRIGGER Motion detection Detect motion in Note Please configure Motion detection first Send 1 pre event image s Send 1 post event image s Delay 3 second s before detecting the next event Sequential Snapshot interval 5 second s Send snapshot by Email O FTP C FTP put snapshots with date and time suffix Click the save settings button when finished You are now able to record snapshots to your FTP server when motion detection is triggered D Link DCS 5220 User Manual 54 section 3 Configuration Installing the Multicamera Managenent Software The IP surveillance software on the CD included with the DCS 5220 Internet Camera converts the DCS 5220 into a powerful yet flexible surveillance system for home or business with these features e Real time Monitoring e Video Recording to hard disk e High quality video e High video compression ratio e Maximum of 16 cameras with diffe
21. camera s Web interface Product Page DCS 5220 Firmware Version 1 03 DCS 5220 LI E IDEO SETUP MAINTENANCE STATUS Live Video e Live Video e Setup e Tools Maintenance e Status Setup Status LIVE VIDEO Logout e Snapshot e Zoom e Connection Type e Configuration Network Setup Dynamic DNS Image settings Audio and Video settings Mail and FTP settings Motion detection Schedule Access List MAINTENANCE e Device Management e Backup and Restore e Firmware Update STATUS e Device Information e Logs D Link DCS 5220 User Manual 49 section 3 Configuration Record Snapshots to your FTP server with Motion Detection Administrators can combine options on the application page to perform many useful security applications To upload the snapshots users can choose either email or FTP according to the user s needs Both e mail and FTP use the network settings on the network page This section describes how to enable motion detecting and record snapshots to an FTP server Administrators can utilize the built in motion detection to monitor any abnormal movement and then record the snapshots to an FTP server D Link DCS 5220 User Manual 50 section 3 Configuration In this window follow the steps below to ensure that motion detection is correctly enabled 1 Check Enable motion detection product Page DCS 5220 SE 2 Click on New to have a new window to monitor video a ee In order to use
22. camera for the video channel the color of the channel number will be gray There is a unique light signal associated with each channel number It indicates the status of the dedicated video channel which is depicted as follows Off The video channel is not connected with any DCS 5220 yet Green The green light means the DCS 5220 associated with this channel number is connected and the video is monitored in the video area Red The red light indicates the video from this channel is recording into the video database In this mode you don t have to drag and drop the channel to the video area This means that this application software supports real time recording with and without real time monitoring for the dedicated video channel oBMNBAN Blink With the motion detection mechanism set in the DCS 5220 the light of the corresponding channel will blink once the motion event is triggered If you do not want to monitor one video you can drag and drop the video in the video area to the trashcan in the common control area of the monitor program The following section will demonstrate the procedures for drag and drop step by step D Link DCS 5220 User Manual section 3 Configuration Show the video of a specified channel This section depicts the method of how to show the video of a specific channel in a display window Step 1 Move the mouse cursor to the camera you would like display in the window Step 2 Press and ho
23. is 21 It depends on the FTP server s setup 2nd FTP user name The account name to access the FTP server 2nd FTP password The password that was setup with the account to access the FTP server 2nd FTP remote Folder The directory that the images will be uploaded into e g pub images 2nd FTP passive mode Check it to enable passive mode in transmission Note The second FTP setting only activates when the first FTP setting fails Invalid settings may cause the DCS 5220 to not respond Change the configuration settings only if necessary Consult with your network administrator or your Internet Service Provider ISP if you do not have the necessary information lf you cannot connect to the camera refer to page 8 for camera reset and restore factory settings procedures D Link DCS 5220 User Manual 33 section 3 Configuration Motion Detection Click the Motion Detection button on the left side of the Setup screen to enable the motion detection function of the DCS 5220 Internet Camera Enable motion detection Check this option to turn on motion Product Page DCS 5220 oe detection New Adds new windows that monitor a S pec ifi C a rea of th e I m ag e WI n dow 7 U p In order to use motion detection you must first check the Enable Motion Detection checkbox 4 t O 9 m ot j O n d et e ct j O n wi n d OW S C an b e m pills of 3 windows can be created each with their own separate Sensitivity and Percentage added o C Enable motion d
24. move to preset locations Left Up Right Down amp Home Zoom Pan Speed Tilt Speed Auto Pan Patrol Speed Current Position Preset Position Home definition Patrol Selection D Link DCS 5220 User Manual Home aims the camera to the center and the other buttons aim the camera accordingly F aT setup Here you can set preset locations and change the default location of your home button 6 JJ controls the zoom out function Zoom automatically returns the lens to normal view controls the zoom in function Select the speed at which the camera will pan for a full cycle from the drop down list Select a value between 5 and 5 5 being the slowest setting Select the speed at which the camera will tilt for a full cycle from the pull down menu erie Select a value between 5 and 5 5 being the slowest setting Select the speed at which the camera will pan during auto patrol Select a value between 1 and 5 1 being the slowest setting Enter a name for the position at which you would like to preset the DCS 5220 Click Add to add the new preset position to the Preset Locations list Using the drop down list you can delete a preset position by selecting it and clicking Delete Use the Save as home button to set the current position as the home position The Home position is the first position the camera goes to after the camera boots You can also recall the def
25. program except the page control In this mode the two labels under the pull bar show the starting and the ending time of the interval individually as shown below lf 3204 AM 04 58 21 1 3 2004 AM 04 58 38 1 NS i r2 2 ay 2 ae afal rye bet vY b et Ea w uy H Ww D Link DCS 5220 User Manual 101 section 3 Configuration Histogram Area The histogram area in the normal display single frame mode only shows the events occurred time and the percentage of motion detection with red bars If you want to access the histogram area you must change the area selection indicator to the histogram area You can mark one time interval you want to see with a color inverted region by dragging your mouse with the left button pressed as shown below When you release the left button the color inverted region will be enlarged to the whole histogram area This color inverted region will be the new period the program is going to display If you change your mind and don t want to see that period you can cancel it by just pressing the right button of your mouse with the left button still pressed If you click on the left button without dragging it the action will be the same as clicking on the pull bar in the same x axis position That means the playback system will shift to the pointed time and show video on the displaying frame Besides the dark regions in the histogram area mean there is no existing vid
26. quality and select a video quality level This setting will utilize more bandwidth to send the maximum frames when images change drastically D Link DCS 5220 User Manual 30 section 3 Configuration Fixed bit rate Fixed quality Mute AAC GSM AMR These settings are to optimize your camera performance with your available bandwidth Select a fixed bandwidth for your camera operation This option allows the user to select a custom frame rate suitable for the bandwidth and the storage space Selecting fixed quality will roughly select your image quality and will not be as accurate as setting by bit rate This setting is easier to use when image quality does not have to be precise Below is a typical file size after 1 minute of recording at 30fps frames per second This is only an average measurement your file size may differ due to lighting black white or color setting and frame rate Medium Standard Good Detailed Excellent 2 589MB 2 857MB 3 571MB 4 598MB 5 357MB This will mute the audio for all connections Advanced Audio Coding A wide band audio coding algorithm that exploits two primary coding strategies to dramatically reduce the amount of data needed to convey high quality digital audio Select a higher bit rate number for better audio quality A standard adapted audio codec by the 3GPP video 8rd Generation Partnership Project It is an Adaptive Multi Rate Narrow Band AMR NB speech codec Select a higher bit
27. quickly If the CD Autorun function does not automatically start on your computer click Windows Start gt Run In the Run command box type D DCS5220 exe where D represents the drive letter of your CD ROM If it does start proceed D Link Click n Conenct DCC DCC will show the MAC address and IP address of your DCS 5220 If you have a DHCP server on your network there will be a valid IP Address displayed at the end of DCC process You can begin to use the IP camera now D Link A DHCP server is a device that supplies IP Addresses to its clients that are on the same network a View QIG a gt View Manual FAES gt gt Multicamera Management f gt gt Install Acrobat Reader LC gt Technical Support SEA DCS 5220 Wireless Network Camera Click Start D Link DCS 5220 User Manual 11 section 3 Configuration Enabling UPnP for Windows XP UPnP Universal Plug and Play is a networking architecture that provides compatibility among networking equipment software and peripherals The DCS 5220 is an UPnP enabled Internet camera If your operating system is UPnP enabled the device will be easier to configure If you do not want to use the UPnP functionality it can be disabled by unchecking the Enabled UPnP checkbox in the Advanced gt Network page see page 32 Use the following steps to enable UPnP settings only if you are running Windows XP If you are running Window
28. system will restart and require the DCC program to locate the IP address of the DCS 5220 D Link DCS 5220 User Manual 45 section 3 Configuration Firmware Update File Path This option allows you to upgrade the firmware via a web browser Click on Browse to locate the i 1 i Device Management Helpful Hints firmware file and then click on Upgrade to apply cK A new firmware upgrade may be available for your name It is recommended to keep your th e fi rm W a r e t O th e Cc a m e r a Firmware Update name firmware up to date to maintain and improve the functionality and performance of your IP Camera Click here_D Link Support Page to check for the latest firmware version available Logout To upgrade the firmware on your name please download and save the latest firmware version from the D Link Support Page to your local hard drive Locate the file on your local hard drive by clicking the Browse button Once you have found and opened the file using the browse button click the Upload button to start the firmware upgrade FIRMWARE INFORMATION Current Firmware Version 1 03 Current Firmware Date 18 Sep 2007 FIRMWARE UPGRADE File Path EE upload D Link DCS 5220 User Manual 46 section 3 Configuration Status Device Info The Device Info screen lists the following important settings that are currently set for the DCS 5220 Se All of your WAN and LAN connection details are displayed here e P ca
29. t Save Settings MEDIA OPTIONS Video amp Audio O Video Only Audio Only PROTOCOL OPTIONS The auto detection order of transmission protcol is UDP gt TCP Please select one protocol as the default protocol Oupp tTcp RECORD OPTIONS Name CLIP File Name Prefix M Add date and time suffix to file name quality However packet losses will diminish image quality when bandwidth becomes restricted TCP Protocol Packet loss is less likely to occur compared to UDP when bandwidth is restricted HELP Allows you to specify where the video image will be saved on your local hard drive when recording video directly from the web interface D Link DCS 5220 User Manual 21 section 3 Configuration DCS 5220 Configuration Setup Product Page DCS 5220 Firmware Version 1 03 There are 5 tabs across the top of the Configuration screen The LIVE VIDEO page is used for viewing live video and audio In this section you can setup the camera s wired and wireless network interface settings If you Th e S ET U P a e S u S e d fo r b a S C S et u of th e D C S Wir Sahin are configuring this device for the first time D Link recommends that you click the Setup Wizard D Q p D button and follow the instructions on screen If you wish to modify or configure the camera yynamic settings manually click manual setup to enable the Camera connection setup yna 522 0 n Internet Connection Setup Wizard Manual Internet
30. time and a warning message will be displayed Playback Method Selector since the program will record the previous start and end time in Time Period and Events Preview mode whenever you want to change the period selector to see the other periods you must change the playback method selector to the mode you want to use first Otherwise the period selector will revert back to the previous period set the last time you changed the playback method selector Full Range If you select this method the database will be displayed from the beginning to the end of this location Any change in the period selector will have no effect except when you change this selector to Time Period Time Period If you change the playback method to Time Period you can modify the start and end time in the period selector When you click on the Play button in the jog dial the period you selected will be displayed Alert Area Selector In the preview mode the playback program can show the information of total events of only one alert window each time If you want to see the events of the other two alert area windows you must change the alert area selector to the other window numbers In the normal display mode the alert window that the alert area selector indicates will be highlighted with red rectangle if you checked that window in the settings dialog The alert area selector will be changed to alert window O by default settings when you ch
31. to the area you intend to select When you select the display area the display adjustment tool will appear in the control area If you select the histogram area the display adjustment tool will disappear and the searching range adjustment tool will be shown in the same place of the control area D Link DCS 5220 User Manual 98 section 3 Configuration Pull Bar The pull bar is a fast flexible control for seeking data in the selected time period It represents the total length of time in that period You can pull the indicator on the pull bar to the specific time point you would like to view The displaying video will halt and then restart playing the video sequence from the point you selected If the video sequence has been paused the display area will show the point you selected without playing Note that the pull bar will only function under the normal display mode Settings After the main window is shown on the screen you must modify the settings to make it to work properly Click on the Settings button shown below in the system control tool and the setting dialog will appear on the screen C WrmssAV DB Record Ci Yrmss YDB AYI po C rmssAVDB Snapshot TO D Link DCS 5220 User Manual 99 section 3 Configuration The items in the settings windows are Database Location The most important item in the settings dialog is the database location setting You must set it to the directory that contains the sur
32. to connect wirelessly so you have the freedom to connect computers anywhere in your home or office network Why D Link Wireless D Link is the worldwide leader and award winning designer developer and manufacturer of networking products D Link delivers the performance you need at a price you can afford D Link has all the products you need to build your network How does wireless work Wireless works similar to how cordless phone work through radio signals to transmit data from one point A to point B But wireless technology has restrictions as to how you can access the network You must be within the wireless network range area to be able to connect your computer There are two different types of wireless networks Wireless Local Area Network WLAN and Wireless Personal Area Network WPAN Wireless Local Area Network WLAN In a wireless local area network a device called an Access Point AP connects computers to the network The access point has a small antenna attached to it which allows it to transmit data back and forth over radio signals With an indoor access point as seen in the picture the signal can travel up to 300 feet With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants industrial locations college and high school Campuses airports golf courses and many other outdoor venues D Link DCS 5220 User Manual 133 Appendix A Wireless Basics Who uses wireless
33. to easily regulate a schedule for each video channel The main features of the scheduling tool are Friendly graphic user interface for schedule editing Flexible schedule scheme suitable for all applications Individual schedule for each video channel Periodic automatic recording D Link DCS 5220 User Manual 18 section 3 Configuration Start the Scheduler The scheduler will not be accessible until at least one camera has been added to the camera list Go to the configuration menu and click on Scheduler to launch the Scheduler Camera Configuration Global Settings Display amp UI Settings Scheduler The Layout and Functionalities Introduction The layout of the scheduler and its components shown below will be described The layout of the scheduler is roughly divided into 4 parts Video Channel Selection Area Primary schedule settings Secondary schedule settings and Operation Buttons Suny do ae BB indas BB indo Ligital iret O Eo Ea EE D Link DCS 5220 User Manual section 3 Configuration Video Channel Selection Area Primary Schedule Secondary Schedule Operation Buttons The video channel selection area provides the IP addresses and location information of the connected video channels for the user s reference You can select a video channel in this area and create a schedule for it The Primary schedule consists of the day time line week time line begin time sel
34. to keep in mind when you install a wireless network Centralize your router or Access Point Make sure you place the router access point in a centralized location within your network for the best performance Try to place the router access point as high as possible in the room so the signal gets dispersed throughout your home lf you have a two story home you may need a repeater to boost the signal to extend the range Eliminate Interference Place home appliances such as cordless telephones microwaves and televisions as away as possible from the router access point This would significantly reduce any interfere that the appliances might cause since they operate on same frequency Security Don t let you next door neighbors or intruders connect to your wireless network Secure your wireless network by turning on the WPA or WEP security feature on the router Refer to product manual for detail information on how to set it up D Link DCS 5220 User Manual 135 Appendix A Wireless Basics Wireless Modes There are basically two modes of networking e Infrastructure All wireless clients will connect to an access point or wireless router e Ad Hoc Directly connecting to another computer for peer to peer communication using wireless network adapters on each computer such as two or more DCS 5220 wireless network Cardbus adapters An Infrastructure network contains an Access Point or wireless router All the wireless devices or
35. 05 Schedule gt Snapshot Check this option to enable the snapshot for motion detection and sequential snapshot Setup FTP o Bad r based ori moter or chgtal ingeut wigger wou can cordoue the fiiia e eai i kr aa aiian dabes ar A a r dis ae e hoe the ewent amp biggered and ahat fon fo parum when it E Giggersd Select the day s according to when you want the camera to take snapshots This enables the camera to take snapshots continuously The time range specified for the snapshot For example the snapshot will start at eight o clock in the morning and stop at five o clock in the afternoon onsen when the following time period is input From 08 00 na aaan to 17 00 scandir before detecting tha rast avent This option will add the prefix to the snapshot file name If you don t have enough upload bandwidth the video clip file will not complete uploading during the time interval and the upload file will not able to playback To avoid the problem please reduce the maximum file size or enlarge the time interval C ETE put sacehots with dube wd ire suite SECURITY This option enables motion detection triggering for snapshot uploading 38 section 3 Configuration Detect Motion in Check the motion detection window s to enable motion triggering The window s can be created in the Advanced gt Motion Detection page Sequential This option enables continuous snapshot uploading Snapshot inte
36. 220 User Manual 131 Appendix A Wireless Basics Wireless Basics D Link wireless products are based on industry standards to provide easy to use and compatible high speed wireless connectivity within your home business or public access wireless networks Strictly adhering to the IEEE standard the D Link wireless family of products will allow you to securely access the data you want when and where you want it You will be able to enjoy the freedom that wireless networking delivers A wireless local area network WLAN is a cellular computer network that transmits and receives data with radio signals instead of wires Wireless LANs are used increasingly in both home and office environments and public areas such as airports coffee shops and universities Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users Under many circumstances it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers printers or an Internet connection supplied through the wired LAN A Wireless Router is a device used to provide this link D Link DCS 5220 User Manual 132 Appendix A Wireless Basics What is Wireless Wireless or WiFi technology is another way of connecting your computer to the network without using wires WiFi uses radio frequency
37. 2nd recipient email address Sender email address FTP SERVER SETTINGS Local FTP server port ist FTP server 1st FTP server port 1st FTP user name ist FTP password ist FTP remote folder ist FTP passive mode 2nd FTP server 2nd FTP server port 2nd FTP user name 2nd FTP password 2nd FTP remote folder 2nd FTP passive mode The e mail address of the recipient for the secondary server The senders email address that appears in the mail alert lt can be another value other than default port 21 If you find that you want to change the port to a port number other than 21 you will need to specify the port when connecting to the FTP server For example FTP 68 5 1 81 60 if you are to use port 60 for your FTP server port D Link DCS 5220 User Manual 32 section 3 Configuration 1st FTP server The host name of the FTP server tst FTP server port The port of the FTP server Usually the port number of an FTP server is 21 It depends on the FTP server s setup tst FTP user name The account name to access the FTP server 1st FTP password The password that was setup with the account to access the FTP server 1st FTP remote folder 2nd The directory that the images will be uploaded into e g pub images 1st FTP passive mode Check the checkbox to enable passive mode in transmission FTP server The 2nd FTP server serves as a backup FIP server 2nd FIP server port The port of the FTP server Usually the port number of an FTP server
38. 3 2 MB 5 Other Network File and Print Services 0 0 MB A Nutlank Fxnress noma Description Contains a variety of specialized network telated services and protocols Total disk space required 54 7 MB Space available on disk 1926 8 MB Click Next Windows Components Wizard Configuring Components Please wait while Setup configures the components Setup is making the configuration changes you requested Please wait while Setup configures the components This may take several minutes depending on the components selected Status Completing configuration of Internet Information Services IIS Windows Components Wizard Completing the Windows Components Wizard You have successfully completed the Windows Components Wizard To close this wizard click Finish Click Finish D Link DCS 5220 User Manual 14 section 3 Configuration To view your DCS 5220 Internet Camera in an Internet browser go to your Desktop and click My Network Places T My Network Places Click DCS 5220 192 168 0 120 ae mn ress My Network Places Local Network Network Tasks G Add a network place D Link Router BB 0cs 5220 192 168 0120 View network connections s i Set up a home or small office network Ee View workgroup computers Other Places Desktop i My Computer My Documents Shared Documents QA Printers and Faxes D Link DCS 5220 User Manual 15 sect
39. 30 If the image quality is low select a lower frame rate above 15 If the image quality is still not improved select a lower bit rate D Link DCS 5220 User Manual 40 section 3 Configuration Access List Click the Access List button from the left side of the Setup screen to access Access List settings Allow List Start IP Address The starting IP Address of the devices Such as a computer that have permission to access the video of the camera Allow List End IP Address The ending IP Address of the mees ALLOW LIST A art IP address devices such as a computer that have permission to access the video of the camera Delete Allow List 1 0 0 0 255 255 255 255 v Delete DENY LIST Start IP address End IP address Delete Allow List Remove the customized setting from the Allow List Delete Deny List Deny List Start IP Address The starting IP Address of the devices such as a computer that don t have permission to access the video of the camera SECURITY Deny List End IP Address The ending IP Address of the devices such as a computer that don t have permission to access the video of the camera Delete Deny List Remove the customized setting from the Deny List D Link DCS 5220 User Manual 41 section 3 Configuration Camera Control Click the Camera Control button from the left side of the Setup screen to access settings that affect how the DCS 5220 Internet Camera can pan and
40. 655 Quick Installation Guide 3 Access the Router with Your Web Browser If you have cable or DSL Internet service you will most likely have a dynamically assigned WAN IP Address Dynamic means that your routers WAN IP address can change from time to time depending on your ISP A dynamic WAN IP Address identifies your router on the public network and allows it to access the Internet To find out what your router s WAN IP Address is go to the Status menu on your router and locate the WAN information for your router as shown on the next Your WAN IP Address will be listed on the router s Status gt Device Info page MAC Address 00 19 50 03 04 58 Network Name SSID dirk Channel 4 Security Mode Deobled Wi Fi Protected Setup Enabled Not Configured IP Address 192 168 0 155 WIRELESS D Link DCS 5220 User Manual 117 section 4 Security Note Because a dynamic WAN IP can change from time to time depending on your ISP you may want to obtain a Static IP address from your ISP A Static IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote location The Static IP Address will also allow you to access your camera attached to your router over the Internet 4 Open Virtual Server Ports to Enable Remote Image Viewing The firewall security features built into the DIR 655 router prevent users from accessing the video from the D
41. CAM Seo 21 19 04 04 IP CAM D Link DCS 5220 User Manual Serial number 001346DBD59C Sep 21 18 20 35 SYS System starts at Fri Sep 21 18 20 35 CST 2007 Sep 21 18 20 36 NET NET INFO Sep 21 18 20 36 NET Host IP 172 17 5 156 Sep 21 18 20 36 NET Subnet Mask 255 255 255 0 Sep 21 18 20 36 NET Gateway 172 17 5 254 Sep 21 18 20 36 NET Primary DNS 192 168 168 210 Sep 21 18 20 36 NET Secondary DNS 192 168 168 201 RTSP Server Start one session IP 172 17 5 170 RTSP Server Stop one session IP 172 17 5 170 RTSP Server Start one session IP 169 254 1 112 RTSP Server Stop one session IP 169 254 1 112 RTSP Server Start one session IP 169 254 1 112 RTSP Server Stop one session IP 169 254 1 112 RTSP Server Start one session IP 169 254 1 112 RTSP Server Stop one session IP 169 254 1 112 RTSP Server Start one session IP 169 254 1 112 RTSP Server Stop one session IP 169 254 1 112 RTSP Server Start one session IP 169 254 1 112 RTSP Server Stop one session IP 169 254 1 112 RTSP Server Start one session IP 169 254 1 112 RTSP Server Stop one session IP 169 254 1 112 RTSP Server Start one session IP 169 254 1 112 UL Firmware Version 1 03 Helpful Hints DCS 5220 LI E IDEO SETUP MAINTENANCE STATUS HELP Dev fo Check the log frequently to detect unauthorized network usage 48 section 3 Configuration Help The help page provides detailed information for the
42. CS 5220 over the Internet The router connects to the Internet over a series of numbered ports The ports normally used by the DCS 5220 are blocked from access over the Internet Therefore these ports need to be made accessible over the Internet This is accomplished using the Virtual Server function on the DIR 655 router The Virtual Server ports used by the camera must be opened through the router for remote access to your camera Virtual Server is accessed by clicking on the Advanced tab of the router screen Follow these steps to configure your router s Virtual Server settings 1 Click Enabled 2 Enter a different name for each entry 3 Enter your camera s local IP Address e g 192 168 0 120 in the example in step 2 on page 122 in the Private IP field 4 Select TCP for HTTP port both TCP and UDP for RTSP and both TCP and UDP for 5556 5559 ports 5 Ifyou are using the default camera port settings enter 80 into the Public and Private Port section click Apply 6 Scheduling should be set to Always so that the camera images can be accessed at any time D Link DCS 5220 User Manual 118 section 4 Security Repeat the above steps adding the port 554 to both the Public and Private Port sections A check mark appearing before the entry name will indicate that the ports are enabled Important Some ISPs block access to port 80 and other commonly used Internet ports to conserve bandwidth Check with your ISP so that you can ope
43. Domain Name Service is a method of keeping a domain name linked to a changing dynamic IP address With most Cable and DSL connections you are assigned a dynamic IP address and that address is used only for the duration of that specific connection With the DCS 5220 you can set up your DDNS service and the DCS 5220 will automatically update your DDNS server every time it receives a different IP address Enable DDNS Select to enable or disable the DDNS function Provider Select your Dynamic DNS provider from the drop down list Hostname Enter the host name of the DDNS server Username Email Enter your username or e mail used to connect to the DDNS server Password Key Enter your password or key used to connect to the DDNS server D Link DCS 5220 User Manual 28 section 3 Configuration Image Setup Click the Image Setup button on the left side of the Setup screen to access additional settings that affect how the video image appears From this screen you can fine tune the video image Color Select the option for color or monochrome video display a 7 A ae lt setup Note If parameters are changed without saving they will be effective until the next system Power line frequency This option allows you to choose the OET oe frequency of the power line for different regions Power Line Frequency in US aiai a Mail and FTP 60HZ Video orientation Flip Vertically rotate the video Mirror Horizontally rotate the vi
44. Enable Disable the time displaying on the video image Allows the user to pan and tilt the camera from the video image Camera Configuration Global Settings You can load a custom wav file for the alert triggering sound or you can selecta uyssseeeyyreerresee sound file from the Windows sound file directory Seb Saree Backup About Display amp Ul Settings 12 hour Format D Link DCS 5220 User Manual 76 section 3 Configuration Display Options In the video displaying frame of each channel there are two status bars The upper bar contains Location channel number camera name and Remote Time The lower bar contains Connection Time Day Hour Min and Recording time Day Hour Min All of them shown in the figure below can be enabled or disabled here individually for the status indication Apply to full screen mode can also be turned on here Once it has been checked the status bar in each channel showing date location connection and recording time will be shown in both display frame mode and full screen mode 01 Front Door 200a A26 22 40 02 D Link DCS 5220 User Manual T1 section 3 Configuration Using the Scheduler This section discusses the method of how to use the scheduler The scheduler allows the user to schedule recordings from the selected video channel of the DCS 5220 Through both the graphic user interface and time period selection options you will be able
45. Statically Assign an IP Address If you are not using a DHCP capable gateway router or you need to assign a static IP address please follow the steps below Step 1 Windows XP Click on Start gt Control Panel gt Network Connections Windows 2000 From the desktop right click My Network Places gt Properties Step 2 Right click on the Local Area Connection which represents your D Link network adapter and select Properties Step 3 Highlight Internet Protocol TCP IP and click Properties Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router Internet Protocol TCP IP Properties Example If the routers LAN IP address is 192 168 0 1 make your IP address You can get IP stings assigned automaticaly your network suppots 192 168 0 X where X is a number between 2 and 99 Make sure that the number you choose is not in use on the network Set Default Gateway the same as the LAN ashan biasane IP address of your router 192 168 0 1 P addes 2e oe Subnet mask 255 255 255 0 Default gateway 192 168 0 ji Set Primary DNS the same as the LAN IP address of your router 192 168 0 1 The secondary DNS is not needed or you may enter a DNS server from your ISP Use the following DNS server addresses Preferred DNS Ei 92 1 68 AR a E Alternate DNS ii Step 5 Click OK twice to sav
46. USER MANUAL DCS 5220 VERSION 2 0 P SECURITS Table of Contents Table of Contents Product OverviewW igcceicscect ve crmseecccsecencsseeandececareesiaespaeen 4 Package Content ccccccecseeeeeeeeeceeeeeeeeseeeeeees 4 System Requirements ccccseccceeeceeeeceeeeeeeseeees 4 rod UON ee merreni E EEEE E NEENA ETIESE 5 Features 00 ccc cec cee ecceeceeceeceeceeceeceeeeesesaeeeeeesaeeaeeas 6 Hardware OVErVieW cccceecceseceeeteeeeeeeeeneeteeeteeeeees 7 Hardware Installation ccccccccceeeeeeeeeeeeeeeeeeeeees 9 Wireless Installation Considerations 10 Configuration os iscstsonerncucunantescopneacenenseseesacseuseeneveenneteaes 11 D Link Click n Conenct DCC ceeeeeeeeeeeeeees 11 Enabling UPnP for Windows XP 00ceee 12 Testing the DCS 5220 1 00 ccecccceeceseeeesseeeeseeeesaaes 17 Viewing Your DCS 5220 ccccccececseeecseeeeseeeeeeees 18 Using the DCS 5220 with an Internet Browser 19 Home Page Screen ccccccseeeeceeeeeeeeeeeeeeees 20 Client Setup cc cece eececeeeteeeeeeeteeeeseeeeeeeteeeeees 21 SD EEEE E EEE 22 AATE E E E E E rucivens 23 Network Setup cccecceceeseeeeeseeeeeeeeeeeeeeeaeees 24 Wireless S tUP cccceccseceteeeeseeeeeeteeeeaseeaness 26 Dynamic DNS esses teeters evecare tudes beeenseeecnanues 28 Image Setup sco seic een settestawansseumeecdaseseoceearel wend 29 Aud
47. address of the camera and also the port that is opened on the camera port 80 in this example The selected camera has been added to the selection list Enana vice less DCS 5220 A1 192 168 0 120 5220 D Link DCS 5220 User Manual 70 section 3 Configuration Delete Highlight the camera that you want to delete from the list and click on the Delete button The selected camera will be deleted History Clicking the History button will popup a historical camera list which lists fee the latest 16 cameras you have inserted into the camera list Clicking on 2 one camera in the history list will insert the camera into the camera list The hisrtory list is shown here Address 192 168 0 120 80 1 DCS 5220 Alert and Recording Settings D Link DCS 5220 User Manual 71 section 3 Configuration Alert Settings Specific alert actions can be performed by setting the options in this window Enable motion detect Enable digital input Digital input alert Record secs before event Record secs after event Media Type This will trigger an alert sound that has been specified in the section titled Display amp UI Settings Local Alert Settings Check this option to enable audio alerts for the selected camera This function is similar to Enable Motion Detect mentioned above Once this option has been checked a digital input device will be able to trigger an alert sound
48. al admin s password dialog looks like this User Management The User Management utility looks like this admin D Link DCS 5220 User Manual 62 section 3 Configuration Monitor Starts up the Monitor program If the Monitor program is already running clicking this button will re open the Monitor window Playback Starts up the Playback program If the Playback program is already running clicking this button will re open the Playback window Logout Logs out user from IP surveillance After logging out if the user wants to return to the menu and clicks the Launcher icon the authentication box will appear prompting for username and password again Exit Exits Launcher If users choose this option Launcher will show a message box prompting to confirm if users really want to exit and warn users that exiting Launcher will also close Monitor and Playback D Link DCS 5220 User Manual 63 section 3 Configuration Monitor Program Features of the Monitor Program Traditional Surveillance Features Real time monitoring Pan and Tilt control Recording Special Features The digital surveillance system supports not only the features listed above but also the following features which make the system more powerful and convenient Simultaneous real time monitoring and recording audio and video High quality video up to full screen display High compression ratio Maximum of 16 cameras with different monitor layouts
49. ange the location selector to another window D Link DCS 5220 User Manual 103 section 3 Configuration Play Control For the play control the jog dial shown in the figure below is used to provide the easiest method of controlling the video sequence display All buttons can control the displaying frame in the normal display mode Play Stop Pause Resume Forward Fast Play and Slow Play D Link DCS 5220 User Manual The supported Play button is an intelligent play user interface The functionality of this button can vary to fit different circumstances In the normal display mode clicking on the Play button can restart the displaying video sequence When you want to stop the displaying video sequence you can click on the Stop button Note that once you press the Stop button the start point will be reset to the start of the present period The Pause button provides you a way to pause the video sequence display When the displaying video is paused click on the Pause button again to resume the video display This button is only valid when the displaying video sequence is paused It will display the next frame in that period when you click on the Forward button one time The camera supports a maximum of x16 fast forward play and minimum of 16 slow forward play This function helps you browse the surveillance database with more flexibility If you want to change the playing s
50. ard InstallShield Wizard Complete i i Setup has finished installing IF surveillance on your computer 59 section 3 Configuration Using the Multicamera Management Software Before you begin installing this application software the hardware system requirements must be checked first The minimum system requirements recommended for this application are as follows e Windows 2000 XP or Vista e At least 256MB of memory 512MB recommended e A wireless 802 11b or 802 11g or Ethernet network e Internet Explorer 6 x or higher Internet Web Browser e VGA card resolution 800x600 or above e CPU 1 3GHz or above processor 2 4GHz processor or higher with 512MB memory and a 32MB video card is required for multiple camera viewing and recording in IP surveillance program Launcher Launcher is a controller program that allows users to invoke Monitor or Playback quickly System Tray Icon The Launcher icon reflects current state of IP surveillance The g icon in the system tray signifies that the IP surveillance software is currently active on the system Security for Launcher When Launcher starts there is no need to undergo a username password check But when users want to click on the icon of Launcher on system tray Launcher will pop up a username password dialog the first time for menu popup or when Username admin 0000 Launcher is locked If a user fails to pass the authentication check no menu will sh
51. arranty for this product If any of the above items are missing please contact your reseller system Requirements e Windows 2000 or XP e At least 256MB of memory 512MB recommended e A wireless 802 116 or 802 119 or Ethernet network e Internet Explorer 6 x or higher Internet Web Browser e VGA card resolution 800x600 or above e CPU 1 3GHz or above processor 2 4GHz processor or higher with 512MB memory and a 32MB video card is required for multiple camera viewing and recording in IP surveillance program D Link DCS 5220 User Manual 4 Section 1 Product Overview Introduction The D Link SECURICAM Network DCS 5220 Wireless PT Internet Camera is a powerful surveillance system that connects wirelessly to your 802 11b g network The DCS 5220 features enhanced 802 11b g and connects wirelessly at arate of up to 54Mbps Megabits per second The DCS 5220 differs from a conventional PC Camera because it is a standalone system with a built in CPU and Web server providing a low cost solution capable of solving demanding security and home office monitoring needs Snapshot enables you to save images directly from a Web browser to a local hard drive without installing any additional software With 1 lux light sensitivity the DCS 5220 is capable of capturing video in rooms with minimal lighting You can also zoom in with the DCS 5220 s 4x digital zoom feature The DCS 5220 gives you the ability to monitor video and audio in your home o
52. ation Main Areas Display Area The display area is able to show the surveillance database of each camera by time You can change the video size through the display adjustment tool and the playback method through the play control tool Under the normal display mode as shown in the figure below you can just double click on the frame area to change the frame size to 1 1 or 2 25 1 Histogram Area The histogram is an interactive control Not only can you get the event s location in time domain and its quantity of the motion percentage but you can also select a group of events or a period from the event histogram area and show it on the display area Control Area The control area contains almost all the control selectors and toolboxes you need to browse the database These control tools include location selector period selector playback method selector jog dial display adjustment tool searching range adjustment tool exporting tool and system control tool Status Area The status area is located at the bottom of the main window It tells you the program status information including display mode display size display speed exporting file format and exporting file name Indicators Area Selection Indicator In the main playback window the display area is surrounded by a blue rectangle This rectangle is the area selection indicator This indicator can be set to either display area or histogram area as long as you move your mouse cursor
53. ault home position use the Default home button To use the Auto Patrol feature select the desired preset positions from the Preset Locations list and add them to the Selected Locations list by clicking Select You can then select the order in which the camera will patrol through the preset locations by selecting a location and clicking UP or DN Click Remove to remove a location from the list 42 section 3 Configuration Maintenance Click on the Maintenance tab to access 3 utility screens for controlling and administering the DCS 5220 The default screen for Maintenance is Device Management Device Management The DCS 5220 is setup without any passwords by default This allows the ability to access the DCS 5220 including the Setup by anyone as long as the IP address is known aa cee It is recommended that you enter a password to restrict ae Eo itr others from accessing your camera ne Type a password in the Admin Password field to enable protection and then confirm the password in the Retype New Password Retype Password Password field User name no user This password is used to identify the administrator You Seer can add accounts with User name and User Password nane for other users in the Add user section A maximum of 20 user accounts can be added D Link DCS 5220 User Manual 43 section 3 Configuration Administrator s password User name User List Delete user
54. ayback Powerful play control tool e Play e Stop e Pause e Step forward e Fast play from x1 to x16 e Slow play from 1 to 16 Convenient display adjustment tool e Zoom in from 1 1 to 2 25 1 e Zoom out from 1 1 to 1 2 e Full screen Flexible searching range adjustment tool e User input from full range to 1 second e Zoom in from full range to 10 seconds e Zoom out up to full range e Full range system control tool e Program locking e System settings D Link DCS 5220 User Manual 96 section 3 Configuration Logging In Before you start the playback program it is necessary for you to log in to the application software The figure below shows the login dialog For security concerns only the admin account can log in to this program To change the password of the admin account please refer to the section titled Logging In on pace 72 Authentication Layout When you successfully log in to the playback system the main window will be shown on the top of the screen and the display resolution will be changed to 1024x768 automatically There are four main areas i e display area histogram area control area and status area There are also three visualized controls i e area selection indicator frame selection indicator and pull bar These features provide much more convenience while searching recorded video in the IP surveillance database D Link DCS 5220 User Manual 97 section 3 Configur
55. cation information from your ISP into these fields Note he Internet WAN IP Address of the PPPoE will be sent through e mail 24 section 3 Configuration HTTP Port Enable RTSP authentication Access name for computer viewing Access name for mobile viewing RTSP port RTP port for video RTCP port for video RTP port for audio RTCP port foraudio D Link DCS 5220 User Manual Can be set to another value other than the default port 80 When the administrator changes the HTTP port of the DCS 5220 which has an IP address of 192 168 0 100 from 80 to 8080 you must type http 192 168 0 100 8080 in the web browser address field to reach the web configuration page This option will turn on the authentication of RTSP You need to specify access name to login camera like this rtps cameraip live sdp This option allows you to specify the file name for RTSP streaming thru computer This option allows you to specify the file name for RTSP streaming thru mobile phone This option allows you to set a port other than the default UDP port 554 The video channel port for RTP It must be even number The video channel port for RTCP It must be the port number of video RTP plus 1 The audio channel port for RTP It must be even number The video channel port for RTCP It must be the port number of video RTP plus 1 25 section 3 Configuration Disable Wireless SSID Wireless Mode Channel TX Rate Preamble
56. ccess the settings from the left side of the Setup menu Time zone Used to adjust the hour of time servers for Pre eee DCS 5220 EEEE local settings Enable Daylight Saving Check this to enable daylight saving ti m e j The Time Configuration option allows you to configure update and maintain the correct time on ie f i the internal system clock From this section you can set the time zone that you are in and set chi schools See eee H wk oe ee Server Daylight Saving can also be configured to automatically Fase a Dy jus i Daylight Saving Dates Set daylight saving time start and end date S25 initi jeter death Sao TIME CONFIGURATION by your local definition a pee ee e Current Server Time 21 Sep 2007 03 06 08 Motion Detection Time zone Enable Daylight Saving C Schedule Daylight Saving Dates Month Week Day of Week Time a a a n Access List DST Start Lst Mon 12a Automatic Time Configuration a F E AUTOMATIC TIME CONFIGURATION Enable NTP Server Synchronize with the NTP server over the th E Internet whenever the DCS 5220 starts Update interval up It will fail if the assigned time server SET THE DATE AND TIME MANUALLY Year 2007 v Month 09 Day cannot be reached be EM i E S E NTP server Used Assign the IP address or domain name of the time server Leaving the text box blank will let the DCS 5220 connect to default time servers Update interval Used to adjust the hour of time servers for local sett
57. clients will connect to the wireless router or access point An Ad Hoc network contains only clients such as laptops with wireless cardbus adapters All the adapters must be in Ad Hoc mode to communicate D Link DCS 5220 User Manual 136 Appendix B Networking Basics Networking Basics Check your IP Address After you install your new D Link adapter by default the TCP IP settings should be set to obtain an IP address from a DHCP server i e wireless router automatically To verify your IP address please follow the steps below Click on Start gt Run In the run box type cmd and click OK At the prompt type ipconfig and press Enter lt C WINDOWS system32 cmd exe Microsoft Windows AP Version 5 1 2600 GC Copyright 1985 2661 Microsoft Corp This will display the IP address subnet mask and the default gateway of your adapter C Documents and Settings gt ipconfig Mindows IP Configuration If the address is 0 0 0 0 check your adapter econ aod teas manne rey installation security settings and the settings TE Addo a ee Ee on your router Some firewall software programs a _ may block a DHCP request on newly installed adapters C Documents and Settings gt _ lf you are connecting to a wireless network at a hotspot e g hotel coffee shop airport please contact an employee or administrator to verify their wireless network settings D Link DCS 5220 User Manual 137 Appendix B Networking Basics
58. creen When you click on the Full Screen button the video sequence will be enlarged to the whole screen instantly You can double click on any place or the ESC key to return back to the normal screen When you switch to the full screen display you can press the Alt and Space keys together to pop the jog dial to control the displaying video sequence Press the same keys again to close the jog dial You can also press the Alt and Enter keys together to switch between the normal display and full screen display at any time when the program is under the normal display mode D Link DCS 5220 User Manual 105 section 3 Configuration System Control Toolbox The system control toolbox provides some basic operations for the playback program The figure below shows the three elements of the system control toolbox i e Lock Window Settings Minimize and Exit Lock Window If you are away from your computer for security reasons we recommend that you to close the playback program or you can just click on the Lock Window button to lock the main window Once you click this button the main window will be hidden and the login dialog will appear To return to the main window you need to re enter the admin s password again Settings The settings dialog will pop up when you click the Settings button For more information about setting this program please refer to the section titled
59. deo Check both flip and mirror if the DCS 5220 is installed upside down IMAGE SETTING White Balance White Balance is related to the color pre eae temperature Color temperature is a way of OO measuring the quality of a light source It is moes based on the ratio of the amount of blue light to the amount of red light while the green light is ignored The unit for measuring this ratio is in degrees Kelvin K Light with a higher color temperature i e larger Kelvin value has more blue light than a light with a lower color temperature The default setting for white balance is Auto SECURITY Brightness Image Brightness is adjustable you can set from among eleven levels ranged from 5 to 5 The default setting is zero D Link DCS 5220 User Manual 29 section 3 Configuration Audio and Video Click the Audio and Video button on the left side of the Setup screen to access audio and video settings that affect how the audio and video appears Configure for computer Select this option to switch to computer viewing viewing S e e ct th l S O pt l O n to S W l tc h to m O b l e d eV l ce This section allows you to configure the sound and video of your IP camera You can configure viewing The frame siZ e will ch ang e t O 176x1 4 4 Gc cen a calla settings depending on whether you are viewing content from aPC or a Mobile Phone Sa a z yN INS _ Save Settings _ Settings 5 FPS and 40kbps video quality
60. dmin administrator to use this application Enter the password for the administrator Note The password is the one you provided during installation Authentication The Admin Privilege In the Monitor program the admin has the right to access the DCS 5220 Network Camera through this application software and change the local settings as well But the admin password for the software is not the same as the admin password for the Internet camera You can change the settings of each selected Internet camera from the Monitor program only if you have the admin password for the Internet camera If you have the admin privilege you have the right to do the following tasks e Run the configuration tool e Change the recording schedule e Change the local settings Again if you need to change the settings of the DCS 5220 you must have the administrators password for the camera itself D Link DCS 5220 User Manual 67 section 3 Configuration Camera Configurations When you log in for the first time you should configure this application software to connect the DCS 5220 in Configuration Menu gt Camera Configurations shown in the figure below You will need the admin administrator password of the Camera in order to run the configuration Global Settings Display amp UI Settings l om E About Once you click Configuration Menu gt Camera Configurations for setting each camera all recording processes will be sto
61. e Internet Camera is not weatherproof and needs to be equipped with a weatherproof case in order to be used outdoors recommended 6 When physically connecting the Internet Camera to a network what network cabling Is required The Internet Camera uses Category 5 UTP cable allowing 10 Base T and 100 Base T networking 7 Can the Internet Camera be setup as a PC cam on a computer No the DCS 5220 Internet Camera is used only on a wireless 802 11b g Ethernet or Fast Ethernet network D Link DCS 5220 User Manual 129 section 5 Troubleshooting 8 Can the DCS 5220 be connected to the network if it consists of only private IP addresses Yes the Internet Camera can be connected to a LAN with private IP addresses 9 Can the DCS 5220 be installed and work if a firewall exists on the network lf a firewall exists on the network port 80 needs to be opened for ordinary data communication The DCS 5220 uses HTTP port and RTSP port to stream video data These ports or the ports you specify from the Advanced Tab in the Configuration screen if you change the default ports need to be opened in the firewall device Please refer to page 124 for more information 10 Why am I unable to access the DCS 5220 from a Web browser lf a router or firewall is used on the network the correct ports for the DCS 5220 may not be configured on the router or firewall To correct the problem you need to determine if the DCS 5220 is behind a router or firewall and
62. e your settings D Link DCS 5220 User Manual 138 Appendix C Technical Specifications Technical Specifications Remote Management e Configuration Accessible via a Web Browser e Take Snapshots and Save to a Local Hard Drive via a Web Browser Networking Protocols e TCP IP HTTP SMTP RTSP FTP NTP DNS DHCP UPnP DDNS PPPoE Connectivity e 802 11b g Wireless with WEP WPA security e 10 100Mbps Fast Ethernet Auto Negotiation Camera Specification e 1 4 CMOS Sensor e 1 Lux F2 0 e AGC AWB AES e Electronic Shutter 1 60 1 15 000 sec e Standard Fixed Mount Type Lens 4mm F2 0 e Viewing Angle 48 45 Horizontal 37 29 Vertical Video Algorithm Supported e 3G Video Support e Enhanced Video Compression Using MPEG4 Simple Profile Video Resolution e Up to 30fps at 160x120 e Up to 30fps at 176x144 e Up to 30fps at 320x240 e Up to 30fps at 640x480 Audio e 16kbps 128kbps AAC e 4 75kbps 12 2kbps GSM AMR Security e Administrator and User Group Protected e Password Authentication IP Surveillance Software e Remotely Manage and Control up to 16 DCS 5220 Internet Cameras e View Up to 16 Cameras on one screen e Supports all Management Functions Provided in Web Interface e Scheduled Motion Triggered or Manual Recording Options Recording Method e Support video clips snapshot upload FTP Email e Support NAS recording e Homepage Recording Snapshot e Bundled PC software IP surveillance recordin
63. eceistaccccascsssscasscaesaessactecantessezecssceus 110 What is WEP pac ercancnetreestenneapmaseomeynieentnteveneestinens 110 What is WPA cccccccceceececeeeeeeeeeeseeeeseeeteneeeaes 111 Setting Security circcteeneen co eacctumonmesseeeraencaueceeemeee sass 112 Using amp Configuring the DCS 5220 with a NAT Router113 Router Set Up and Installation 0 117 Using amp Configuring 3G Compatible Cell Phones 120 Play from RealPlayer secccacasee cae reeeninaneccemeoseaie 121 Pay WOM VAY GP oes sconteepseregesiveveceetastgien est 126 Troubleshooting cesta ccccsis icc see toceentecdvacawenneceresuandees 129 Wireless BASICS nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 132 Wireless Modes c s cesccescenssesscessenssenseesseeseoneees 136 Networking Basics ccscsscsssesssessesensseeeenseeeeeeees 137 Check your IP Address cccccccceeeeseeeeeeeeeeeees 137 Statically Assign an IP Address 0cceeeeee 138 Technical Specifications ccsscesseeeseeeeeseeeees 139 D Link DCS 5220 User Manual Section 1 Product Overview Package Contents e D Link DCS 5220 Wireless PT Internet Camera with 3G Mobile Video Support e CAT5 Ethernet Cable e Power Adapter e Antenna e Manual and Software on CD e Quick Install Guide e Camera Stand Note Using a power supply with a different voltage than the one included with your product will cause damage and void the w
64. ector end time selector and event mode settings The Secondary schedule consists of event mode settings The operation buttons allow the user to manipulate the edited schedule of the selected video channel The scheduler can be closed from here The Functionalities of Configuration Components The four main parts of the scheduler have been briefly described above The four parts will be described in detail in the following section Video Channel Selection Area In this area you will select the video channel that you want to set a schedule for Each video channel will display a name an IP address and the location Please note that when you switch between video channels in this area the changes in the schedule of the previous video channel will be saved automatically D Link DCS 5220 User Manual Camera 1 192 168 0120 5220 IC i z F A A DCS 5220 Camera 2 dA 80 section 3 Configuration Primary Schedule schedule with Time Lines There are two different time lines hour unit time line and week unit time line You can make your own schedule by plotting markers in all time lines These two time lines are associated with each other That is if you make changes in one time line the corresponding changes will be applied with scale to the other three time lines in the same schedule Before you begin make sure that you select Once page 85 if you want to choose the days to record on Week Time Line
65. eo data in that interval If you click on those regions nothing will happen except a warning message will pop up aaea al Using Tools In this section the method of how to use the tools in the control panel Shown in the main playback window will be discussed Location Selector Tools T The figure below shows the selector tools They are location selector period selector for the E selection of the beginning time and the ending time playback method selector and alert area L704 selector AM O4SE21 Period End Time 17 32004 zl AM 04 58 38 Playback Method Alert Area Selection i D Link DCS 5220 User Manual 102 section 3 Configuration Location Selector The location selector is a control that lets you select the camera you want to see refer to the figure above The location name is the same as the camera name text on video unless you have specified otherwise Period Selector Period selector provides you a precise way to choose the start time and the end time of a new period The end time must be later than the start time After you provide the correct start and end time clicking on the Play button in the jog dial will play the new period in the display area with changing the period start and end time label Besides the pull bar and histogram area will change too If the selected period is not present in the database the data in the period selector will change to the previous correct start and end
66. etection Save Saves the new windows settings Window Name The name of the motion detection window Sensitivity Adjusting the sensitivity allows you to set the amount of motion required to trigger motion detection If you want to detect most or all movement use a high sensitivity If you want to ignore smaller amounts of movement use a SECURITY low sensitivity Percentage Adjusting the percentage allows you to set a requirement on how much of the motion window must be filled by movement Example If you set this to 50 then the selected window must be half filled by a moving object before it triggers motion detection D Link DCS 5220 User Manual 34 section 3 Configuration To display motion detection a graphic bar will rise or fall depending on the image variation A green bar means the image variation is under the monitoring level and no motion detection alert is triggered A red bar means the image variation is over the monitoring level and a motion detected alert is triggered When the bar goes red the window that the motion is detected in will also be outlined in red Note remember that you can have up to 3 windows selected for motion detection You can return to the DCS 5220 Home Page and the monitored window will not be visible but the red frame will show on the home page when motion is detected D Link DCS 5220 User Manual 35 section 3 Configuration Time and Date Click on the Time and Date button to a
67. ffice using an Internet browser from any where in the world Simple installation procedures along with the built in Web based interface offers easy integration to your network environments Customers also have the ability to view live video streams from a compatible 3G cell phone The live camera feed of the D Link Wireless PT Internet Camera can be pulled from the 3G cellular network by using a compatible cell phone with a 3G video player From anywhere within the 3G service area both consumers and small businesses are offered a flexible and convenient way to remotely monitor a home or office in real time Note Use of audio or video equipment for recording the image or voice of a person without their knowledge and consent is prohibited in certain states or jurisdictions Nothing herein represents a warranty or representation that the D Link product provided herein is suitable for the end user s intended use under the applicable laws of his or her state D Link disclaims any liability whatsoever for any end user use of the D Link product which fails to comply with applicable State local or federal laws 1 Maximum wireless signal rate derived from IEEE Standard 802 11b g specifications Actual data throughput will vary Network conditions and environmental factors lower actual data throughput rate 2 4x digital zoom enlarges an image by magnifying the pixels in a selected portion of the image by 4 times 3 3G phone must be equipped with 3G
68. g Viewer e ActiveX control plug in for Microsoft Internet Explorer with D Link digital certificate RealPlayer e Apple Quicktime Browser e Internet Explorer v6 LEDs e Power LED red Link LED green Power D Link DCS 5220 User Manual 139 Appendix C Technical Specifications e External Power Supply e 12V DC 1 5A e Power Consumption 4 8W Dimensions e 4 33 L x 4 13 W x 4 41 H without Antenna Temperature e Operating 0 40 C 32 104 F e Storage 20 70 C 4 158 F Humidity e 20 80 RH non condensing Warranty e 1 Year 1 4X digital zoom enlarges an image by magnifying the pixels in a selected portion of the image by 4 times Maximum wireless signal rate derived from IEEE Standard 802 11b g specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Environmental factors will adversely affect wireless signal range D Link DCS 5220 User Manual Version 2 0 10 25 2007 140
69. g snapshots in bmp format from video channels of the monitor tool and playback programs The directory for storing the recorded video data from video channels The directory for storing the default and user customized schedules for the scheduled recording of each channel Record Diskspace Usage Settings When you turn this setting on the video database system of this application will overwrite the oldest data if the specified path has become full That means it will record video data in a loop If this setting is unchecked all recording will stop when the limit of the hard disk usage is reached Indicate the size of the hard disk that will be reserved for other Windows applications at least 300MB The remainder of the hard disk space will be available for recording The more space you have reserved the less there will be available for your camera s to record to As you move the bar to the right more space will be available for your camera s and conversely less space will be available for your other applications If the recording data exceeds this limitation the new video data will replace the oldest data on a First In First Out FIFO basis when Cycle Recording has been checked 19 section 3 Configuration Modulation Mode Display Option Misc Alert Sound Display amp UI Settings You must select the input signal format NTSC or PAL for displaying the original resolution of video stream from DCS 5220
70. hown below The icons from left to right are Quit Minimize Full Screen Lock Stop Alert Sound and Configuration Menu D Link DCS 5220 User Manual 93 section 3 Configuration Quit By clicking this button IP surveillance will be closed with the latest settings saved Minimize Minimize the Monitor program Full Screen With this function you can enlarge the selected video channel to a full screen display Pres the ESC key on the keyboard or double click the mouse on the screen to return to a regular display Lock When this item is selected Launcher will enter lock mode In lock mode whenever users want to invoke the menu a dialog asking for ID and password will appear Stop Alert Sound If an alert is triggered the alert sound will start to play After being informed of the situation you can press this button to stop the alert sound It will also switch the I O Control to the Alert Message receiver so that the alert messages can be reviewed Configuration Menu The menu includes Camera Configuration Global Settings Scheduler and About options Common Control Functions This section will describe the common control functions of the icons shown below These functions only apply to the currently selected channel The icons from left to right are Volume Record Stop Record Snapshot Printer and Trash Can Volume Control Click on this button to adjust your volume settings Record By clicking on this button
71. ich is assigned by the een Administrator The Administrator can release a public user name and password so that when remote users access the Internet Camera they will have the right to view the image transmitted by the Internet Camera When the Internet Camera is used for the first time it is highly recommended that the Administrator set the Administrator s Password to constrain user access to the Internet Camera since the Default settings are Null String no password Once the Password is defined only the Administrator has access to the management of the Internet Camera This procedure should be done as soon as possible since the security features of the Internet Camera will not be enabled until the Administrator Password is defined D Link DCS 5220 User Manual 112 section 4 Security Using amp Configuring the DCS 5220 with a NAT Router D Link s DCS 5220 is a versatile and cost effective Internet Camera offering both video and audio monitoring It can also serve as a powerful surveillance system in security applications The DCS 5220 can be used with any wired or 802 11b g wireless router This section explains how to view the camera from either the Internet or from inside your internal network Materials Needed e 1 DCS 5220 Internet Camera e 1 Ethernet Cable e A Wired or Wireless router such as the D Link DIR 655 Wireless Router e Ethernet based PC for system configuration Setting up the DCS 5220 for Use Behind a Router
72. icker You can change the hour and minute settings for the beginning and ending time with them 9 9 9 Begin Tuesday 4 ifo 4 End Tuesday E H fo Note The time set in Begin time must be earlier than that in End time Otherwise the settings will not be applied Apply and Erase Buttons After you have selected the time period with Begin time and End time picker you can apply the period picker shown in the figure below to set the periodical types of the time interval set previously After the settings in Begin Time End Time and Period Picker are all done you should click the Apply button or Erase button on the right to add or clear this scheduling information to the editing schedule scheme Note that only after you click on the Apply button the scheduling information settings will be written back into the whole editing schedule scheme That means this edited scheduling time interval is valid only after you Apply the changes f Once Every day D Link DCS 5220 User Manual 82 section 3 Configuration Schedule in Event Mode You can select to record in Event mode or Continuous mode by the Schedule mode selector as shown in the figure below There are two types of event recording Please refer to the following two sections for more information Motion Detection As shown below you can check the windows that you would like to record while the motion detecti
73. ings The time interval for the camera to update the time settings from a NTP server Set the date and time manually Adjust the date and time according to what is selected by the administrator Copy Your Computer s time Settings Synchronize the date and time of DCS 5220 with your local computer The date and time of the PC is displayed and updated in the DCS 5220 D Link DCS 5220 User Manual 36 section 3 Configuration Schedule Click on the Schedule button to access the Schedule settings Kom gil gil side of the Setup menu Video Clip This option enables the camera to record video clips Snapshot This option enables the camera to take snapshots WEEKLY SCHEDULE ry Sun Mon Tue Wed mu Fr Sat Time Trigger Send video Clip aways motion mal always motion mal schedule gt Video Clip Enable video clip Check this option to enable video clip for motion detection and sequential video clip Weekly schedule Select the day s according to when you want the C ee eee a hiai nus leer feat nar ee EA arene prepa cue iPada ie yous camera to make a video clip re l Always This enables the camera to make video clips continuously From 00 00 to 00 00 The time range specified for the video clip For example the video clip will start at eight o clock in the morning and stop at five o clock in the afternoon when the following time period is input From 08 00 to 17 00 Video clip file name prefix This option will
74. io ANC Video c cece eeccecceeeeeeeeeeeeeseeeeeeaees 30 Mailand FIP Sesoapsscctcocresvetasaanernueepenrdevenceecemess 32 D Link DCS 5220 User Manual Motion Detection ccccccecceeceeeeeeaeeeeeeeeeeees 34 ime and Date ve sitancatintinadcwapaunsdsenssiaeedeuesntencease 36 10 210 0 seerne E eee EE 37 WIGS OO ccs E E E oF SHADSNOL viieswaparseucesareswcheainepetddnasrannenwseanounns texas 38 PROC CSS LS Use depose Er enc EEE EEFE 41 Camera Control scnsssiuaesties carnenratesacteeerecsssorstine 42 Maintenance cceccecceeceeceeceececeecaeceeeceeaeeseeeeesenseesaees 43 Device ManagemMen ccccseccseeseeeeeeeeeeeeeeneeens 43 Backup and Restore ccccceeceeceeceeeceeseeeeeseeees 45 Firmware Update ccccccceccecceeeeeeeeeeseeseeeeeeaeees 46 IS A EE A 47 Device INFO 0 cec cece eecceeceeeceeteeeeeeeeesaeeeeeeeeeeeeaeeees 47 OO oe celvacs use aemenoices E 48 PVC EE N E A EA A 49 Record Snapshots to your FTP server with Motion Detection cecceccecceeceeceeceeceecaesaeeaeeeeeceesueeeeseeseesaesaees 50 Installing the IP surveillance Software 008 55 Using the Multicamera Management Software 60 LIC OM aaen ENE ENNES EERE EAEE EEEE 60 Monitor PrOQram ccccccscccscceeeceeeseeeeeeeeeeseeeaeeeeees 64 Playpack PIOOI AIM sooner ireen EREE EPEE 96 Schedule Video Recording with Motion Detection 107 Table of Contents Wireless DOC UU s
75. ion 3 Configuration After you click on the DCS 5220 icon your Internet browser will automatically be opened to the IP Address of the DCS 5220 in this example it is http 192 168 0 120 Your DCS 5220 may have a different IP Address D Link DCS 5220 User Manual Product Page DCS 5220 Firmware Version 1 03 LI E IDEO SETUP MAINTENANCE STATUS HELP Select One LIYE VIDEO Pan Speed Tilt Speed Auto Pan Stop Auto Patrol Snapshot J 2 I E o SECURITY 16 section 3 Configuration Testing the DCS 5220 Open your Internet browser and type in the IP address of the DCS 5220 In this example the address is http 192 168 0 120 your DCS 5220 may have a different IP address based on what you used in the DCC program 2 1 B t SECURITY The window in the center of your browser is the camera image window You should now see a video image and hear the audio over your computer speakers from the DCS 5220 If you are having problems please consult the Troubleshooting section of this manual page 128 D Link DCS 5220 User Manual 17 section 3 Configuration Viewing Your DCS 5220 After all the router settings have been entered correctly a PC user inside or outside your network will have access to the camera through the Internet Explorer Web browser To access the camera from the Internet type the IP Address of the router given to you by your ISP followed by a colon
76. irectory This is the directory where backup data will be saved You can select the location by clicking on the folder icon Size You can set the size limit of the data that will be backed up The default size limit is 10MB The maximum value for this setting depends on the amount of Free Space available on your hard drive This value can be found under the Record Disk space Usage Settings section of the global settings window Backup Location Select Select the locations to backup by clicking the checkbox next to the location camera name To delete a location select the location and click the Delete button to the right of the Backup Location Select window After you have set your backup settings in the global settings window you can backup recorded data by clicking Backup in the Configuration Menu as seen below Camera Configuration Global Settings Display amp UT Settings Scheduler Abouk D Link DCS 5220 User Manual 86 section 3 Configuration Using the Monitor Program This section depicts in detail how to manipulate the monitor tool Connection of the DCS 5220 Once you have the privilege to connect to the DCS 5220 the cameras will automatically appear in the video area in the order they are connected Once you have set up the camera in the video channel the color of the channel number will turn green indicating that the camera has been added to IP surveillance If you do not set up the
77. isplays the status of each video channel The information indicates the status of connection recording selection and alert event trigger In this area you can see the video of the selected channel in the display frame The number of the display frames in the video area depends on the layout chosen by the user You can also use convenient controls to alter the video display You can change the monitoring layout in this area There are six kinds of layouts 1 4 6 9 13 or 16 video display windows in the video area In this area you can get the status of the hard disk in which the video database resides The status reminds you of the available storage space remaining on the hard drive you have selected to record to This area includes volume control manual recording video printing snapshot and trash can to remove video from display windows This tool receives the digital input signal and sends digital output signal to the remote Video Server Network Camera series product associated with the dedicated video channel This tool will display the latest alert messages received by the remote Video Server Network Camera series product associated with the selected video channel D Link DCS 5220 User Manual 66 section 3 Configuration Logging In You need to login the first time when you start the Launcher The authentication window is shown below If you do not have an account the monitor tool will not execute You must log in as a
78. l TCP v 6 Schedule Inbound Filter Allow All Schedule Always Inbound Filter Allow All Schedule Inbound Filter Allow All SETUP ADYANCED TOOLS STATUS SUPPORT VIRTUAL SERVER Helpful Hints Check the Application Name drop down CK T ext to own menu to fill out the corresponding field You can select a computer from the list of DHCP clients in the Computer Name crop down menu or you Y t 7 computer at which you would like to open the specified port Select a schedule for when the virtual server will be enabled If you do not see the 119 section 4 Security Using amp Configuring 3G Compatible Cell Phones Before you start please refer to page 30 to find the Access Name of the RTSP protocol To enter the RTSP streaming address please follow this format rtsp io address of the camera live sdp To enable mobile device video streaming you will need to select Configure for mobile viewing see sample screenshot to the right D Link DCS 5220 User Manual Product Page DC Firmware Version 1 03 LI E IDEO SETUP MAINTENANCE STATUS HELP Setu This section allows you to configure the sound and video of your IP camera You can configure different settings depending on whether you are viewing content from aPC or a Mobile Phone Save Settings Don t Save Settings mage Setup GENERAL i 4 Mail and ETP Configure for computer viewing sl Roker Dekection
79. l pop up in a new window This image can be saved to your local hard drive D Link DCS 5220 User Manual DCS 5220 LI E IDEO SETUP MAINTENANCE STATUS HELP Client Setup Tilt Speed 4uto Pan ___ Auto Patrol Snapshot 2 1 B t o SECURITY 20 section 3 Configuration Media Options Protocol Options Record Options Client Setup You can disable audio when viewing video disable video while keeping audio or have both video and audio present Most users should use the UDP protocol Generally the client computer will automatically try these protocols in the following order UDP gt TCP After the client connects to the DCS 5220 successfully the working protocol will be displayed in Protocol Options The chosen protocol will be saved in your PC and used for the next connection If the network environment is changed or users want to let the Web browser automatically detect the protocol select UDP manually and click Save to change the setting and return Home to reconnect with the new setting Options UDP Protocol Offers the highest image and video Product Page DCS 5220 DCS 5220 LI E IDEO SETUP MAINTENANCE STATUS Camera Client Setup Firmware Version 1 03 Helpful Hints e UDP Protocol This Here you can configure the audio and video settings as well as the type of connection your llows quality real time camera uses when viewing it on a network Save Settings Don
80. ld the left mouse button and then drag it to a display window in the video area on the right side of the screen Note that the cursor will change according to the area in order to indicate whether the area is droppable or not T D1ink A a i IP surveillance Step 3 Release the left mouse button while on top of a display window The video will appear in the display window as shown below In each display layout only one window can be assigned to a camera Also each camera must have its own separate window when displayed Once the video is in a display window it can be dragged and dropped to other windows If you drag one camera s video to a window that already has its own camera s video the two cameras will trade display windows Dragging and dropping is a very convenient way to manipulate the video channels in the IP surveillance Software D Link DCS 5220 User Manual 88 section 3 Configuration Removing video from a display window Step 1 Move the mouse cursor to the display window that contains the video channel you wish to remove AE Ea 2005 12 08 12 55 48 PM Step 2 Note that the cursor will change to the hand shape when it has been moved onto the displaying frame After that press the left mouse button and hold it Step 3 Move the cursor while still holding the left mouse button to the trashcan in the common area of the monitor program n iis D Link IP surveillance Step 4 When the cursor shape changes t
81. le camera environment Product Page DCS 5220 Firmware Version 1 03 Note Ports 5556 5559 and both HTTP port and RTSP Wizard Helpful Hints port are required to be opened for the DCS 5220 Please You can configure your LAN and Internet settings from here refer to page 112 on how to open ports in the router el GENERAL Audio Video LAN Settings DHCP Fixed IP IP Address Subnet Mask Mail and FTP Time and Date schedule Default Router Primary DNS 192 168 168 210 Secondary DNS L92 Enable UPnP presentation C Enable UPnP port forwarding O PPPoE Settings User name Password Confirm password Connect status PORT DETAIL SETTINGS HTTP Enable RTSP authentication Access name for computer viewing live sdp Access name for mobile viewing ep live 3qp RTSP port 554 RTP port for video RTCP port for video RTP port for audio 5556 RTCP port for audio 55 Note ATP video port and ATP audio port must be an even number RTC video port and RTOP audio port must be RTP video port and RTP auaio port ada I inalviduady Save Settings Don t Save Settings SECURITY D Link DCS 5220 User Manual 116 section 4 Security Router Set Up and Installation The following steps generally apply to any router that you have on your network The D Link DIR 655 is used as an example to clarify the configuration process Configure the initial settings of the DIR 655 by following the steps outlined in the DIR
82. ly an example You will probably have a different IP Address D Link Congratulations vee 2 Setop Devici You have completed the Network Camera Installation ere Please find your Camera IP address listed below Enter this URL into gt gt 6100 Complete any web browser to access your camera settings URL https 172 17 5 108 Installation is now complete Click on the EXIT button to close the program now or the ADVANCED Options button should you want to configure the advanced camera options Video of selected IP camera a ADVANCED Options D Link DCS 5220 User Manual 114 section 4 Security 2 View the Internet Camera Using Your Internet Explorer Web Browser Run your Internet Explorer Web browser In the address bar type in the IP Address that was assigned to the Internet Camera by the DCC program The DCS 5220 Live Video Page appears with a window displaying live video from the camera You are able to view this screen from any PC running Internet Explorer on your LAN Click on the Setup button on the left side of the display Scroll to the bottom of the Network Setup page see page 24 to display the ports used by HTTP and Streaming audio and video 2 1 we oe SECURITY D Link DCS 5220 User Manual 115 section 4 Security The Setup gt Network Setup page displays the port settings for your camera If necessary these ports can be changed if they are already in use by other devices e g in a multip
83. matically in your environment you may slow down the maximum frame rate to 20 to decrease the transmitted data for better video quality Since the human eye can not easily differentiate between 20 and 25 or 30 frames per second the slower frame rate will not be noticed If your network bandwidth is below 384 Kbps you should adjust the bit rate according to your bandwidth and experiment to allow for the best frame rate that can be achieved The faster frame rate in a slow network will blur the images You may also try to choose 320x240 in size option for better images or 640x480 for larger image size Because the network has burst constraints and everyone s environment is different any poor connection will impair normal performance Recording settings for clear identification for each image To have the best video quality you should set Fixed quality to detailed or excellent and tune the Maximum frame rate to suit your network bandwidth If you get some broken pictures in a slow network you can set TCP protocol in Connection type for a more accurate transmission but the received images may have a lag Note that any slow connection with multiple users will impair performance Recording settings to compromise between real time and clear images If you have a broadband network set Fixed quality to Good image quality or higher instead of setting the Bit rate Otherwise fix the bit rate according to your actual network speed and set the frame rate to
84. me subnet The default value is 255 255 255 0 Enter the IP address of the router gateway Invalid router settings may cause failedtransmissions to a different subnet The primary domain name server that translates names to IP addresses The secondary domain name server to backup the primary one Universal Plug amp Play This option allows a computer to find this camera through UPnP which will show up under Network Neighborhood without configuration UPnP is based on TCP IP and Internet eee UPnP is a networking architecture that provides compatibility among Delat Miber Primary D NS Storey WS liinabia UPnP presentation LO rabie UPA port donating DPPP Setting Lie naa Pacrerond Confirm paraad PORT DETAIL SETTINGS HTTP E Grable ATSP authentication ACCES Mane for papu vara ARK AT HRS pon amg ATE dud oot oT Oe an Sra murba ATCO Meee ot ang ATC ARDO port mia ba RTP Mie port ang RATE aul pert aod Ul naoa SECURITY networking equipment software and peripherals The camera is a UPnP enabled device and it will work with other UPnP devices and software The camera will add the port forwarding entry into the router automatically when this option is enabled Point to Point Protocol over Ethernet Select this option if the camera is directly connected to the Internet through a DSL modem and the ISP Internet Service Provider requires you to use PPPoE for the Internet connection Enter the authenti
85. mee Configure for computer viewing t Frame size There are 4 options for the size of the video Teada T Configure for mobile viewing VIDEO SETTINGS display You can select 160x120 176x144 ECE mam a 320x240 or 640x480 The maximum frame rate cme ar is 30fps for all resolutions E Fixed quality Good iv Maximum Frame Rate Limits the maximum refresh frame rate The AUDIO SETTINGS frame rate is used with the Video quality control Zia sales setting below to optimize bandwidth utilization cama Bit Rate 12 2Kbps v and video quality Key frame interval Determines how many repeated P frames will appear after one frame A large key frame interval can reduce the bit rate but cause image to be corrupted longer if there is packet loss while transmitting The video quality may be poor due to the sending of maximum frame rate within the limited bandwidth when images are moving rapidly Consequently to ensure detailed video quality quantization rate regardless of the network it will utilize more bandwidth to send the maximal frames Video quality control Used when images change drastically To fix the bandwidth utilization regardless of the video quality choose Fixed bit rate and select the desired bandwidth The video quality may be reduced in order to send maximum frames with limited bandwidth especially when images change drastically For higher video detail regardless of the bandwidth selection select Fixed
86. mera name ci INFORMATION 7 IP camera name DCS 5220 e Time and Date Hct Seep CeRSRSS Firmware Version 1 03 18 Sep 2007 Fi rmwa re Ve rsion IP address 172 17 5 156 IP Subnet mask 255 255 255 0 Default Gateway 172 17 5 254 IP address pays este e IP Subnet mask PPPoE E e Default Gateway e Primary DNS e Secondary DNS PPPoE e DDNS D Link DCS 5220 User Manual 47 section 3 Configuration Log The content of the log file reveals useful information about the current configuration and connection logged after the DCS 5220 starts up Enable remote log IP Address Port Current log Product Page DCS 5220 This option enables the camera to send camera log files to a remote server The IP address of the remote server Inf The port number of the remote log server The default port is 514 SETTINGS C Enable remote log Log server settings IP address Port View the system log file The content of the file reveals useful information about camera configuration and connectivity status after the camera boots up CURRENT LOG Sep 21 18 20 35 SYS Sep 21 18 38 36 IP_CAM Sep 21 18 38 41 IP_CAM Sep 21 18 47 50 IP_CAM Sep 21 18 48 01 IP_CAM Sep 21 18 48 31 IP_CAM Sep 21 18 52 02 IP_CAM Sep 21 18 52 54 IP_CAM Sep 21 18 53 42 IP_CAM Sep 21 18 54 06 IP_CAM Sep 21 18 55 36 IP_CAM Sep 21 18 57 21 IP_CAM Sep 21 18 58 02 IP_CAM Sep 21 19 02 48 IP_CAM Sep 21 19 03 58 IP_
87. motion detection you must first check the Enable Motion Detection checkbox maximum of 3 windows can be created each with their own separate Sensitivity and Percentage ranges 3 Enter in a window name C Enable motion detection 4 Tune the Sensitivity and Percentage 3 22030 according to the local environment a Combined higher sensitivity with lower DER percentage gives you high sensitivity for the ZS kean motion detection MEF Sensitivity 5 Click on save to enable the activity Next click the Mail and FTP button under the Setup tab to set the FTP server settings for the DCS 5220 D Link DCS 5220 User Manual 51 section 3 Configuration In this window enter the settings for the FTP server you wish to upload the image to Optionally you can enter settings for a secondary backup FTP server Local FIP server port 1st FTP server 1st FTP user name 1st FTP password 1st FTP remote folder D Link DCS 5220 User Manual The Default port is 21 To connect to an FTP server it is recommended that you do not change the port number unless your camera is behind a router If your camera is behind a router you can assign any port number to this field but you must enable port forwarding on the router Please refer to your router manual for more information on port forwarding If you are going to upload snapshots to an FTP server you will need to fill in the Domain name or IP address of your inte
88. n in the upper left corner of the video area will switch to the previous selected multi camera layout The position that each video channel is in for every layout will be saved for the next time the layout is selected Input Output Control Tools IP surveillance includes DI DO control Digital Input Digital Output control and an alert message receiver Each of these are described in detail on the following pages Note The DI DO is not available in the DCS 5220 camera 2 P r 13 a wao e 2 Ea D Link DCS 5220 User Manual 91 section 3 Configuration Clicking on the DI DO button shown below you can switch to the DI DO controls The color of the channel number indicates the status of the camera s DI Digital Input You can click the Switch button to change the HI LOW state of the DO Digital Output With these features you can monitor the remote sensor input from DI and also trigger the camera by DO switch 3 PI LE nT RT LILA a we i a 1 a E J ions Eee Teor When the color of a DI DO channel number is gray that means the video channel has not yet been connected to a camera Alert Message If you have checked the box Enable Motion Detect or Enable Digital Input onthe Camera 12 16 45 dev 1 closed Configurations gt Alert Settings screen the alert message will show in the window shown Rerenneng ced abo
89. n the appropriate ports accordingly If your ISP does not pass traffic on port 80 you will need to change the port the camera uses from 80 to something else such as 800 Not all routers are the same so refer to your user manual for specific instructions on how to open ports Enter valid ports in the Virtual Server section of your router Please make sure to check the box next to the camera name on the Virtual Server List to enable your settings D Link DCS 5220 User Manual Product Page DIR 655 PORT FORWARDING APPLICATION RULES QOS ENGINE NETWORK FILTER WEBSITE FILTER INBOUND FILTER FIREWALL SETTINGS ADVANCED WIRELESS LUTE 1S WIS Hardware Version 41 Firmware Version 1 02 The Virtual Server option allows you to define a single public port on your router for redirection to an internal LAN IP Address and Private LAN port if required This feature is useful for hosting online services such as FTP or Web Servers Save Settings Don t Save Settings 24 VIRTUAL SERVERS LIST Name DCS 5220 IP Address 192 168 0 120 Name DCS5 5220 IP Address 192 168 0120 Name IP Address 0 0 0 0 A A A A A A A A A A A A Public HTTP 20 Private Computer Name v 80 Public Application Name v 554 Private Computer Name v 554 Public Application Name v oO Private Computer Name v Oo Port Traffic Type Protocol TCP v 6 Protocol TcP v 6 Protoco
90. nicate with your network If you are not sure whether your radio supports the Short RF preamble then make sure you disable this feature Long Preamble is the default as it is a required setting for Wi Fi compatibility select the encryption type from the drop down list The default setting for encryption is None which means the security is disabled 26 section 3 Configuration Auth mode Key length Key format Key index Pre shared key D Link DCS 5220 User Manual If the encryption type selected is WEP from the Security drop down list choose one of the authorization modes Open communicates the key across the network Shared allows communication only with other devices with identical WEP settings select the key length either 64 bits or 128 bits select an ASCII or HEX hexadecimal key format You can create up to 4 different security keys The Key allows the camera to connect to other devices by using WPA PSK encryption Pre shared key must be 8 63 characters or 64 hex characters 2 section 3 Configuration Dynamic DNS Click the Dynamic DNS button on the left side of the Setup screen to access Dynamic DNS settings tess P icra yO i its FTE THI spat mehe 1 apepewa myos dyan ore af TP aisa Mer oes ee wag a icine Lear a to connect to your game Pryder dinkbddns cenmifras m Host Mame Leeman Or Eal Passerond oF key Verity Password of Key Ske Dynamic DNS DDNS Dynamic DNS
91. nk DCS 5220 User Manual 127 section 4 Security Enjoy streaming video on your cellphone D Link DCS 5220 User Manual 128 section 5 Troubleshooting Troubleshooting 1 What is an Internet Camera The Internet Camera is a stand alone system connecting directly to an Ethernet or Fast Ethernet network It differs from a conventional PC Camera the Internet Camera is an all in one system with built in CPU and Web based solutions providing a low cost solution that can transmit high quality video images for monitoring The Internet Camera can be managed remotely accessed and controlled from any PC Notebook over an Intranet or the Internet from a Web browser 2 What is the maximum number of users that can be allowed to access DCS 5220 simultaneously The maximum number of users that can log onto the Internet Camera at the same time is 10 Please keep in mind the overall performance of the transmission speed will slow down when many users are logged on 3 What algorithm is used to compress the digital image The Internet Camera utilizes MPEG 4 Simple Profile Mode image compression technology to provide high quality images 4 Can capture still images from the Internet Camera Yes you are able to capture still images with the snapshot function from the software application CD supplied with the Internet Camera or with the snapshot function on the Home page using an Internet browser 5 Can the Internet Camera be used outdoors Th
92. nna is included with the DCS 5220 It is fastened onto the antenna connector located on the back panel which is used to provide a connection with a wireless network Microphone The DCS 5220 Internet Camera has a built in internal microphone Power LED As soon as the power adapter is connected to the camera the red LED and the green LED light will both appear steady on As the camera is booting a flashing red LED and steady green LED light will appear next The red LED will be turned off during self test Upon passing the self test a steady red LED and flashing green LED light will appear indicating a good connection to the Ethernet port D Link DCS 5220 User Manual Section 1 Product Overview DC Power Connector The DC Power input connector is labeled DC 12V with a single jack socket to supply power to the DCS 5220 Ethernet Cable Connector The DCS 5220 features a RJ 45 connector for connections to 10Base T Ethernet cabling or 100Base TX Fast Ethernet cabling The port supports the NWay protocol allowing the DCS 5220 to automatically detect or negotiate the transmission speed of the network Reset Button When the reset button is pressed the power and activity LED light will both appear steady on While pressing the reset button both LEDs will begin to flash indicating that the DCS 5220 s settings are now restored to factory default Release the reset button D Link DCS 5220 User Manual Section
93. o an arrow shape over the trashcan release the left mouse button The video in the corresponding display window will disappear D Link DCS 5220 User Manual 89 section 3 Configuration The Layout There are six different layouts available as shown below for the display windows in the monitor program You can select between 1 camera 4 camera 6 camera 9 camera 13 camera and 16 camera layout You can select one of them by clicking on a layout icon In each layout you can drag and drop the channel number to any display window in the video area Following the procedures described in the section titled Show the video of a specified channel you can add the video channels to display windows within the selected layout in the video area one by one You can also exchange the video between different display windows by dragging and dropping Double clicking on a display window will switch to single channel layout When you choose the one channel layout or four channel layout the Page up and Page down buttons will be shown in the left bottom corner of the video area You can use these two buttons to switch the pages as shown in the figure below D Link DCS 5220 User Manual 90 section 3 Configuration To view an individual camera from the multi camera layout double click on the desired display window You will see that the size of the display window is the same as the one channel layout Clicking the Back butto
94. o your new selected location and release the mouse button Then Video 1 will be moved to the 12th row in this example Information P 165 0 100 80 Once you click the Save button see page 75 in the left bottom corner of this window the y changes for all camera configurations will be saved and will be applied immediately to the IP surveillance D Link DCS 5220 User Manual 13 section 3 Configuration Global Settings After completing the connection to each remote Network Camera we need to configure the global settings for all the cameras These include the video database directory the usage of the Hard disk and options for video display Camera Configuration mech Global Settings Display amp UI Settings Scheduler Backup About You can activate the global settings window from Configuration Menu gt Global Settings shown above All recording processes will be stopped when activating the global settings window indicated by a warning window popped up in advance to keep you informed Global Settings IP surveillance Warning Continuing will Force all recordings to stop Do You Wank ko continue p 3 ist Backup DCS 5220 A1_2 First Backup D Link DCS 5220 User Manual section 3 Configuration Snapshot directory Recording directory Scheduler directory Cycle Recording Reserved space D Link DCS 5220 User Manual Directory Settings The directory for storin
95. of the direct line between network devices A wall that is 1 5 feet thick 5 meters at a 45 degree angle appears to be almost 3 feet 1 meter thick At a 2 degree angle it looks over 42 feet 14 meters thick Position devices so that the signal will travel straight through a wall or ceiling instead of at an angle for better reception 3 Building Materials make a difference A solid metal door or aluminum studs may have a negative effect on range Try to position access points wireless routers and computers so that the signal passes through drywall or open doorways Materials and objects such as glass steel metal walls with insulation water fish tanks mirrors file cabinets brick and concrete will degrade your wireless signal 4 Keep your product away at least 3 6 feet or 1 2 meters from electrical devices or appliances that generate RF noise 5 If you are using 2 4GHz cordless phones or X 10 wireless products such as ceiling fans lights and home security systems your wireless connection may degrade dramatically or drop completely Make sure your 2 4GHz phone base is as far away from your wireless devices as possible The base transmits a signal even if the phone in not in use D Link DCS 5220 User Manual 10 section 3 Configuration Configuration Turn on the computer and Insert the D Link DCS 5220 Driver CD in the CD ROM drive The step by step instructions will help you to search and setup your IP camera smoothly and
96. on 3 Configuration For detailed information about each setting please refer to Configuration gt Advanced gt Motion Detection in the section titled Using the DCS 5220 With an Internet Browser page 29 Next run the IP surveillance program Click on the Configurations button and select Scheduler Camera Configuration Global Settings Scheduler In the Primary Schedule you can choose either Once for one time recording or Every Day for scheduled recording For example if you would like to record events every day during a certain time frame click on the beginning time and drag your mouse to the ending time Schedule recording can be configured by minutes hours days weeks or months The Secondary Schedule allows you to set a schedule outside the Primary Schedule The Secondary Schedule provides two options to record without a specified date or time You can select Event Mode which will record whenever an event is triggered or Continuous Mode which will begin continuously after scheduling settings are saved You do not need to set the Secondary Schedule with the Primary schedule To schedule video recording with motion detection you can use either the Primary Schedule or Secondary schedule or both D Link DCS 5220 User Manual section 3 Configuration In this window follow the steps below to schedule video recording with motion detection in the Primary Schedule 1 Check if you want the recording
97. on is triggered Digital Input In the figure below there are four conditions for the digital input Check the condition that you would like to record while the condition triggers Note The Digital Input is not available for the DCS 5220 camera D Link DCS 5220 User Manual 83 section 3 Configuration High Checking this will trigger recording while the digital input is high The technical name for this event is line trigger Low Checking this will trigger recording while the digital input is low The technical name for this event is line trigger Rising Checking this will trigger recording while the digital input is changing from low to high The technical name for this event is edge trigger Falling Checking this will trigger recording while the digital input is changing from high to low The technical name for this event is edge trigger Schedule in Continuous mode lf you select Continuous mode in the schedule mode selector it will record continuously during the schedule that is set up by the user secondary Schedule secondary schedule is for recording outside of the primary schedule The secondary schedule provides options to record without a specified date or time Schedule modes There are three modes in the secondary schedule Disable Event mode and Continuous mode If event mode is selected in the secondary schedule the camera will record whenever an event is triggered If continuous mode is selected
98. operly configured with a valid IP address Turn off DHCP from the Network Settings in Windows and configure the computer with a valid IP address or connect the camera to a router with DHCP enabled see page 144 10046 is che error 13 Why does a series of broad vertical white lines appear throughout the image It could be that the CMOS sensor has become overloaded when it has been exposed to bright lights such as direct exposure to sunlight or halogen lights Reposition the Internet Camera into a more shaded area immediately as prolonged exposure to bright lights will damage the CMOS sensor 14 Noisy images occur How can I solve the problem The video images might be noisy if the Internet Camera is used in a very low light environment To solve this issue you need more lighting 15 The images appear to be of poor quality how can improve the image quality Make sure that your computer s display properties are set above 256 colors Using 16 or 256 colors on your computer will produce dithering artifacts in the image making the image appear to be of poor quality The configuration on the Internet Camera image display is incorrect Through the Advanced gt Image Setting section of the Web management you need to adjust the image related parameters such as brightness contrast hue and power line frequency for fluorescent light Please refer to the Advanced gt Image Setting section on Page 43 for detailed information D Link DCS 5
99. ormation for the setup please contact with your Internet Service Provider or network administrator This button will take you to the network setup page where ee can configure the Internet connection settings manually This section will help you set up motion detection and it s action This wizard can help you to setup the motion detection step by step including the motion ee area sensitivity and the schedule of actions This button will take you to the motion detection setup page This wsd wi guide you through a step by step process to configure your new DO Link a the camera to the intamet To set up your motion detection please chek Beck bo close the earand and re open the motion detection witan SECURITY This wiad wal gude you through a step by step process to configure your cameras moton detection fumctians Ti SECURITY 23 section 3 Configuration DHCP IP Address Subnet Mask Default Router Primary DNS Secondary DNS Enable UPnP Enable UPnP port forwarding PPPoE D Link DCS 5220 User Manual Network Setup DCS 5220 will request a new IP address from the DHCP server everytime it restarts Once the DCS 5220 is configured this radio should be unselected at all times If this radio button has been selected and the connection is lost run the DCC find the camera s IP address Necessary for network identification Used to determine if the destination is in the sa
100. ove a component click the checkbox A shaded box means that only part of the component will be installed To see what s included in a component click Details Components O E Message Queuing wh MSN Explorer m Networking Services O3MB O 39 Other Network File and Print Services 0 0 MB MEA Qutlank Fxnress nor Description Contains a variety of specialized network related services and protocols Click Details select Universal Plug and Play Networking Services To add or remove a component click the check box 4 shaded box means that only part of the component will be installed To see what s included in a component click Details Subcomponents of Networking Services im Internet Gateway Device Discovery and Control Client 0 0 MB LJ Pz RIP Listener CO E Simple TCP IP Services B Universal Plug and Play Description Allows you to find and control Internet connection sharing hardware and software that uses Universal Plug and Play Total disk space required 54 7 MB Space available on disk 1926 8 MB Click OK D Link DCS 5220 User Manual 13 section 3 Configuration Windows Components Wizard Windows Components You can add or remove components of Windows xP To add of remove a component click the checkbox A shaded box means that only part of the component will be installed To see what s included in a componert click Details Components EZ Message Queuing OOMB A Wi MSN Explorer 1
101. ow up If a user fails 3 consecutive tries he she will be locked out for a period Password Be of 60 seconds Authentication D Link DCS 5220 User Manual 60 section 3 Configuration After passing authentication users will be able to use all functions If users want to leave the computer it is possible to lock the Launcher for security reason When Launcher is locked the user will need to pass authentication again to see the popup menu Note For initial setup the default Username is admin The password is the password provided during installation When Launcher is locked the unlock window will appear prompting for the user password in order to unlock Authentication The input area of the dialog will be grayed disabled for 60 seconds after 3 consecutive failures User Interface Below is the user interface for Launcher Lock Monitor start up mode Tools Monitor Playback Logout D Link DCS 5220 User Manual 61 section 3 Configuration The main user interface for Launcher is an icon on system tray and the popup menu appears when the user clicks on the icon The menu items are listed below Lock When this item is selected Launcher will enter lock mode In lock mode whenever users want to invoke the menu a dialog asking for ID and password will appear Monitor start up mode Users can select whether or not to autorun Launcher when Window boots up Tools The Change loc
102. owerful IP surveillance software allows an administrator to modify the Internet Camera settings from a remote site via the Intranet or the Internet Administrators are capable of monitoring live video feeds as well as recording video and taking snapshots eVariety Data Archive Record video clips directly onto a Network Attached Storage NAS or to a network based computer The DCS 5220 allows you to schedule both recorded video and snapshots to be uploaded onto an FTP server or sent via e mail e Broad Range of Applications With today s high speed Internet the Internet Camera provides the ideal solution for live video images over the Intranet and Internet for remote monitoring The DCS 5220 allows remote access from an Internet Explorer Web browser for live image viewing with audio and allows the administrator to manage and control the Internet Camera anywhere and any time Apply the Internet Camera to monitor various objects and places such as homes offices banks hospitals child care centers amusement parks and other varieties of industrial and public monitoring The Internet Camera can also be used for intruder detection with its motion detection mode capture still images and video images for archiving and many more applications The wireless capability enables you to place the camera where it is inconvenient to install network cables D Link DCS 5220 User Manual Section 1 Product Overview Hardware Overview Antenna Connector One ante
103. peed you just need to move the speed indicator To increase playing speed move the indicator in the clockwise direction And to decrease playing speed move it in the counterclockwise direction The current speed that is set will be shown in the second column of status area 104 section 3 Configuration Display Adjustment Tool When you move the mouse cursor to the displaying area the display adjustment toolbox will appear Using the display adjustment toolbox you can change the displaying video sequence to the size you want to see in the normal display mode when you move the area selection indicator to the display area The figure below shows the display adjustment toolbox and its own three elements i e Zoom In Zoom Out and Full Screen Zoom In When you click on the Zoom In button one time the image size in the display area will be magnified 12 5 percent to the original size Due to the limitation of the display area size the maximum Zoom in ratio Supported is only 2 25 1 for NTSC modulation mode and 1 875 1 for PAL modulation mode If you want to see the image in more detail you can use the full screen function that is Supported in the same toolbox Zoom Out When you click on the Zoom Out button one time the image size in the display area will be minified 12 5 percent to the original size To show the location and time information completely the minimum zoom out ratio is limited in 0 5 1 Full S
104. pped indicated by a warning window popped up in advance to keep you informed IP surveillance Warning Continuing will Force all recordings to stop Do You want ko continue D Link DCS 5220 User Manual 68 section 3 Configuration The Layout of the Configuration This section discusses the local settings for the connection and the functional configuration of each camera If you are interested in the remote settings for each camera you can refer to Using the DCS 5220 with an Internet Browser page 29 Load Settings Alert Settings Recording Settings zirus YE zamn T IH 2 Pha pre bein Pashia E pirat iarria DiziST hatte Save In the local settings shown below three main functionalities are provided Insert Click to insert a new camera to the list Delete Click to delete a camera from the list History Click to view the history of all cameras in the list D Link DCS 5220 User Manual 69 section 3 Configuration Insert To insert a remote network camera to the camera list Click the Insert button an Insert New Channel dialog will popup as shown here Specify the IP address port and admin password of the network camera click the OK button to close the dialog Then the system will try to connect to the selected camera If the connection succeeds the camera will be inserted to the camera selection list Insert New Channel Once the camera is added you will see the IP
105. rate number for better audio quality D Link DCS 5220 User Manual 31 section 3 Configuration 1st SMTP mail server 1st SMTP account name 1st SMTP password 1st recipient e mail address 2nd SMTP mail server 2nd SMTP account name 2nd SMTP password 2nd recipient email address Sender email address Local FTP server port Mail and FIP Product Page DCS 5220 Firmware Version 1 03 The domain name or IP address of an external mail server The user name used to log into your e mail account e g jdoe or jdoe yourisp com The password used to log into your e mail account The password will appear as dots instead of entered characters The e mail address of the recipient for snapshots or a system log file The domain name or IP address of a secondary mail server used only if the primary mail server is unreachable The user name for the second SMTP server The password used to log into the second e mail account The password will appear as dots instead of entered characters SECURITY This section enable you to specify the IP camera email and FTP settings Only modify these settings if your details change or you are experiencing issues with alert notifications Save Settings Don t Save Settings SMTP MAIL SERVER SETTINGS ist SMTP mail server ist SMTP account name ist SMTP password ist recipient email address 2nd SMTP mail server 2nd SMTP account name 2nd SMTP password
106. rent display layouts e Smart playback e Triggered event browsing e Fast database searching e Configurable automated alarms e Account password protection e Scheduled recording for each camera e Email FTP video snapshots e AVI file export e Motion detection for each camera View QIG gt View Manual gt gt Multicamera Management gt Install Acrobat Reader gt Technical Support Click Multicamera management To install IP surveillance click on the Multicamera management link on the CD included with the Internet Camera a es 5270 Wireless Network Camera greserersemennesereesnenenenenenennnenenenenen O D Link DCS 5220 User Manual 55 section 3 Configuration r InstallShield Wizard The Welcome screen appears Welcome to the InstallShield Wizard for IP surveillance The InstallShield Wizard will install IF surveillance on your computer To continue click Mest Cancel Click Next Please read the Software Licensing Agreement and click Yes if you MERGEA wish to accept the agreement Click No to exit the installation License Agreement Please read the following license agreement carefully Press the PAGE DOWN key to see the rest of the agreement D Link Software License Agreement General Termes IMPORTANT READ BEFORE COPYING INSTALLING OR USING PLEASE READ THIS AGREEMENT CAREFULLY BEFORE USING THIS SOFTWARE D LINK SYSTEMS INC O LINR
107. rnal external FTP server such as dlink com or 192 168 0 123 The server name and IP address will vary depending on the user The following user settings must be correctly configured for remote access Specify the user name to access the external FTP server ex John Smith Specify the password to access the external FTP server ex 12345 Specify the destination folder in the external FTP server ex snapshot Product Page DCS 5220 Firmware Version 1 03 DCS 5220 LI E IDEO SETUP MAINTENANCE STATUS HELP Wizard i Audio and Video Mail and FTP Motion Detection SECURITY Helpful Hints This section enable you to specify the IP camera email and FTP settings Only modify these settings if your details change or you are experiencing issues with alert notifications Save Settings Don t Save Settings SMTP MAIL SERVER SETTINGS ist SMTP mail server ist SMTP account name ist SMTP password ist recipient email address 2nd SMTP mail server 2nd SMTP account name 2nd SMTP password 2nd recipient email address Sender email address FTP SERVER SETTINGS Local FTP server port ist FTP server ist FTP server port ist FTP user name ist FTP password ist FTP remote folder ist FTP passive mode 2nd FTP server 2nd FTP server port 2nd FTP user name 2nd FTP password 2nd FTP remote folder 2nd FTP passive mode 52 section 3 Configuration 2nd FIP server 2nd FTP user name 2nd FTP password
108. rval The time interval for continuous snapshot uploading Email This option enables the camera to send the snapshot via e mail FTP This enables the camera to send the snapshot to a FTP server FTP put sanpshot with date This option will add a date and time indicator to the video clip file name For instance snapshot 20060102030405 and time suffix mpg indicates that the snapshot was captured at Year 2006 Month January Date 2nd Time 03 04 05 AM D Link DCS 5220 User Manual 39 section 3 Configuration Recommendations for Setting Video for the Best Performance Best performance means the image refresh rate should be the fastest possible and the video quality should be the best possible at the lowest network bandwidth possible Three factors Maximum frame rate Fixed bit rate and Fixed quality in the Video Configuration page are related to performance Recording settings for real time motion images To achieve a real time visual effect the network bandwidth should be large enough to transmit 20 image frames per second fps or more If you are on a broadband network over 1 Mbps you can set Fixed bit Rate to 1000Kbps or 1200Kbps or set Fixed quality to achieve the maximum frames The maximum frame rate is 25 in 50Hz system and 30 in 60Hz system If your network bandwidth is more than 384Kbps you can adjust Fixed bit rate according to your bandwidth and set the maximum frame rate of 25 to 30 If the images vary dra
109. rypting data over your wireless network so that it is protected as it is transmitted from one wireless device to another To gain access to a WEP network you must know the key The key is a string of characters that you create When using WEP you must determine the level of encryption The type of encryption determines the key length 128 bit encryption requires a longer key than 64 bit encryption Keys are defined by entering in a string in HEX hexadecimal using characters 0 9 A F or ASCII American Standard Code for Information Interchange alphanumeric characters format ASCII format is provided so you can enter a string that is easier to remember The ASCII string is converted to HEX for use over the network Four keys can be defined so that you can change keys easily D Link DCS 5220 User Manual 110 section 4 Security What is WPA WPA or Wi Fi Protected Access is a Wi Fi standard that was designed to improve the security features of WEP Wired Equivalent Privacy The 2 major improvements over WEP e Improved data encryption through the Temporal Key Integrity Protocol TKIP TKIP scrambles the keys using a hashing algorithm and by adding an integrity checking feature ensures that the keys haven t been tampered with WPA2 is based on 802 11i and uses Advanced Encryption Standard instead of TKIP e User authentication which is generally missing in WEP through the extensible authentication protocol EAP WEP regulates
110. s 98 2000 UPnP is not available Go to Start gt Settings Click Control Panel Click Add or Remove Programs D Link DCS 5220 User Manual E Set Program Access and Defaults ee Windows Catalog tp Windows Update Programs i q Documents ____ ____ we Settings Control Panel E Metwork Connections p Search amp Help and Support i Printers and Faxes Taskbar and Start Menu Log OFF PMalan Turn OFF Computer Windows XP Professional 12 section 3 Configuration ey Currartly natalliad programe sort bY Morne i Change or 3l DameWare NT Utilities Remove Mogens BADRI ADEN oy a Add jem E irtena Expires Qam750 Prog arn D IP ssvedarce lt 0 3 390 Click Add Remove Windows Components ane O umae am eran paeme rantena m ouse IP Windows XP Hottie KBa23182 p Wiis YP etfi crass 1 Windows XP Hottie KBa24105 GE Wierds 2 heifir Biss E Windows XP Hotte BE24 146 f worsens 2 hetdie cers 9 F Windows XP Hotie kpa2so35 f Winden 1P rete SP1 See QIIO for mora fermen JB Windows XP Hottie 5P2 See Q329 15 for more information ys Wiima P reef z SPY See QIIUIO for more fornuti E e N EA The following screen will appear Windows Components Wizard Windows Components You can add or remove components of Windows XP Select Networking Services To add of rem
111. schedule to occur Once or Every day 2 Set the date time line and begin and end times for recording 3 Check Event Mode 4 Select the motion detection window that will be used to trigger motion detection Note You must first create motion detection windows in the Web configuration page of the camera Remember the names of the windows and the order in which you created them as they are not displayed inside the scheduler Instead they are listed in the order they were added For example the first window created is labeled Window 5 Click on Disable under the Secondary Schedule Click the Save button when finished You have now set a schedule to record video when motion detection is triggered If you would like to save this configuration click Save As to save this configuration to a folder in your hard drive This configuration can be used on another system running IP surveillance or can be used as a backup if you need to re install the IP surveillance software program D Link DCS 5220 User Manual 109 section 4 Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders The DCS 5220 offers the following types of security e WPA PSK Pre Shared Key e WEP Wired Equivalent Privacy What is WEP WEP stands for Wired Equivalent Privacy It is based on the IEEE 802 11 standard and uses the RC4 encryption algorithm WEP provides security by enc
112. the camera will begin recording continuously after scheduling settings are saved These two modes are the same as the primary schedule Please refer to the previous section for more detail B atian derstir E inal P ine D Link DCS 5220 User Manual 84 section 3 Configuration Operation Buttons There are six operation buttons that allow you to handle the schedule schemes Load Undo Clear Save Save as and Close These operation buttons are shown in the figure below Load Clear Save Save As Undo Close D Link DCS 5220 User Manual Save asi Close This button allows you to load pre edited schedules from the scheduling directory for the selected video channel Note that you should save the schedule you are currently working on before loading a new one Otherwise the current changes will be lost This button will clear all changes in the current schedule of the selected video channel This button is used for saving changes to the current schedule This button is used to save the current schedule as another file name instead of the default name Click on this button to undo all changes for the current schedule since the last save Click on this button to close the scheduler 895 section 3 Configuration Backup Settings Using Backup Settings in the global settings window you can backup recorded data from selected cameras to a specified location D
113. ve Once the alert caused by motion detection or a digital input level change is triggered Reconnecting the alert message will be shown in this window If there are more events than this window aowmeting 1 closed Reconnecting i i 1z2 17 251dev 1 closed can display a scroll bar will appear DEE E 12 17 38idev 1 closed Reconnecting The message format is described as follows 12 40 26 dev 1 closed Reconnecting 12 40 40 dey 1 closed time gt alert type channel number win 1 win2 wins ea Teed Reconnecting For example the message PM 02 41 00 gt MO 1 0 1 1 means that this is a motion detection alert occurring at 02 41 00 PM in Motion Window 2 and Motion Window 3 for camera 1 If the message PM 02 41 56 gt DI 1 is listed that means there is an alert triggered by the DI for camera 1 at 02 41 56 PM D Link DCS 5220 User Manual 92 section 3 Configuration About By choosing About located in the configuration menu shown below a dialog box will appear and display the information about the installed version of IP surveillance The information includes the software name version user name and company Camera Configuration Global Settings Display amp UT Settings Scheduler Backup stow O Miscellaneous Functions This section will describe some other miscellaneous functions of the icons s
114. veillance database to make the program work properly AVI File Location This sets the directory where exported AVI files will be stored Exported AVI files will be stored in the sub directory Camera name under the directory you set here Snapshot File Location This sets the directory where bitmap files will be stored when you use the snapshot to export them Exporting bitmap files will be stored in the sub directory camera name under the directory you set here Modulation Mode The modulation mode cannot be changed This depends on how you recorded the video sequence in the monitor program If you select the wrong mode the video shown in the display area will become distorted If you have chosen the wrong modulation mode you may open the settings dialog again change to the correct mode and restart the playback program The display will now be normal Normal Single Frame Mode While in the normal single frame display mode you can change the video currently displayed by 1 Changing the database path for retrieving another one in the settings dialog of System Control tool 2 Changing the location selector to another location in control area 3 Changing the playback method selector to Full Range 4 Changing the playback method selector to Time Period D Link DCS 5220 User Manual 100 section 3 Configuration Under the normal display single frame mode you can use all the tools provided with the playback
115. video playback such as RealPlayer or PacketVideo for Symbian or PocketPC D Link DCS 5220 User Manual 5 Section 1 Product Overview Features e 3G Compatibility Offers customers the ability to view live video streams from a compatible 3G cell phone The live camera feed can be pulled from a 3G cellular network by using a compatible cell phone with a 3G video player e Supports a Variety of Platforms Supporting TCP IP networking SMTP e mail HTTP and other Internet related protocols the DCS 5220 Internet Camera can be integrated into other Internet Intranet applications because of its standards based features e Remote Snapshot Images Video Clip You can save snapshots video clips directly from the Web browser to a local hard drive without installing any additional software making it convenient to instantly capture any moment from a remote location e Low Light Recording and 4x Digital Zoom The DCS 5220 s 0 5 lux light sensitivity allows you to capture video in rooms with minimal lighting making it ideal for use at night time The camera also features 4x digital zoom for closer viewing e Web Configuration Using the Internet Explorer Web browser administrators can configure and manage the Internet Camera directly from its own Web page via the Intranet or the Internet Up to 20 user names and passwords are permitted with privilege settings controlled by the administrator e Powerful Surveillance and Remote Monitoring Utility The p
116. you can manually record video from the selected channel Stop After video recording has been activated this button allows you to manually stop recording the selected video channel D Link DCS 5220 User Manual 94 section 3 Configuration Snapshot This button will take a snapshot of the selected video channel and then save the picture as a bitmap file to the hard disk You can set the directory for storing these bitmap files at the Configuration menu gt Global Settings screen Please refer to the section titled Global Settings for more details see page 80 Printer Click on the printer icon to print the current image to your default printer Trashcan You can drag and drop the video channel to the Trashcan to close the video connection with the DCS 5220 Status Bar The status bar shown below displays information about the IP surveillance program such as Local Time Current Login User Login Time Software Name and Software Version es ie aban ee ee a ee ORA Logged in when 2005 12 07 05 10 00 PM D Link DCS 5220 User Manual 95 section 3 Configuration Playback Program The playback program is a very powerful convenient and easy way to browse the recorded video It has one display mode normal display mode and two playback methods full range and time period There are several main functions including special features in the Playback program These functions are depicted as follows Features of Pl

D-Link DCS-5 0 User Manual - Dlinkddns.com

Contents

Download Pdf Manuals

Related Search

Related Contents