"user manual"
Contents
1. 100 power mode second press 3 x XML II 100 power mode third press all 7 LEDs on 100 power mode fourth press off M ee Attach the NW7 head securely to your dive harness when not held in hand Do not let the light head dangle or be dragged on the bottom during the dive Do not disconnect the head from the accu when under water this will cause flooding and irreversible damage to the head and the inside parts i Push the RCA After the dive plug into the MA Before disconnecting the head from the canister rinse the 7 an whole set connected head plus accu in fresh water Dry lt l the head cable and RCA connection point plug and canister s top completely before disconnecting the RCA plug from the canister To disconnect the plug from the canister turn the rotating nut in an anti clockwise direction and pull it firmly Do not pull by the cable Immediately after disconnecting the cable s RCA plug dry it Check the visual condition of the head and cable again Storage n Check the head s condition and dry it if necessary ene co CR Store the head in a dry place again before Store the head in a way preventing accidental switch on _ entering the watery or disconnected from the accu make sure the ACCU s RCA port and head s RCA plug are not prone to getting wet moisture f Cable s RCA plug Clean and dry this part before connecting the cable to the accu and aft2. LIGHT FOR ME light for me User s Manual NW7 RCA head Light for me NW7 RCA head Optics 4x XPE 6 degrees up to 1200 lumens 18W 100 power mode e 3 X XML II 70 degrees up to 3600 lumens 30W 100 power mode all 7 LEDs on up to 4800 lumens 48W 100 power mode Piezo switch recessed in the housing no influence over compass made from anodised aluminium stainless steel gland with spring tough cable with RCA plug detachable from the ACCU cable length standard 110cm SideMount custom made up to 123cm Before the dive Check the head s visual condition see if the front glass is not chipped or broken Check the cable if it is cut or damaged Check the cable s RCA plug it should be clean and dry remove any dust or sand with a clean tissue see photo below Put the head s RCA plug into the ACCUs cable entry press it slightly until the whole RCA plug is inside the ACCU RCA port and turn the rotating cap tightly see photos Check if the head is working by pressing the switch make sure the torch is not switched on for more than x 2 5 seconds on the surface Do not direct the light into ewm 00 yours or anyone else s eyes Operating the head to switch between the modes press firmly the Piezo switch first press 4 x XPE www light for me com Before connecting the cable to the RCA port slide back the rotating nut and carefully place the C plug into the port
3. er disconnecting it Burn times NW7 RCA head can be powered by light for me ACCUs with compatible RCA cable entry point Burn time given at 100 power depends on the battery pack and is as follows 4 x XPE 18W up to 1200 lumens 3 x XML Il 30W up to 3600 lumens all 7 LEDs on 48W up to 4800 lumens ACCU XS 4 4Ah 14 4V 3 5h 2h 1h 10min ACCU S 6 75Ah 14 4V 5h 20min 3h 2h ACCU M 11 25Ah 14 4V 9h 5h 20min 3h 10min ACCU L 22Ah 14 4V 17h 10 5h 6 5h ACCU 18Ah 12V 12h 6h 4 5h Given burn times are rounded may differ from real burn time 10 Given burn times are based on battery packs provided by light for me only Given burn times are based on one head connected to the ACCU It is not recommended to drain the battery pack completely Troubleshooting Problem Solution NW7 RCA light head does not switch on One some of the LEDs is not working One some of the LEDs seem to be darker than the rest The light spot of the light head seems to be different irregular The light power seems to be lower The NW7 RCA head accu have been underwater without the RCA plug fully closed There is water in the head The front glass is fogged from the inside The cable is damaged torn or cut There are visible holes cuts in the cable Charge the ACCU according to the instructions provided Clean the ACCU s connection port and cable RCA pl
4. ug The light head needs to be serviced The LED is damaged and or burnt Contact the manufacturer seller for further instructions The light head needs to be serviced The LED is burnt Contact the manufacturer seller for further instructions The light head needs to be serviced The optics is probably damaged due to too high temperature inside the head from switching the light on the surface for too long time Contact the manufacturer seller for further instructions The set needs to be serviced it has flooded Contact the manufacturer seller for further instructions The light head needs to be serviced High risk of flooding the torch if it is immersed in water with its cable damaged Contact the manufacturer seller for further instructions Manual ver 1 0 www light for me com
Download Pdf Manuals
Related Search