-"tt - Hobbyking
Contents
1. is set to 3 2V Cell and the battery pack is 3S 3 Cells then the cutoff threshold of this battery pack is 3 2 3 9 6V b Ifyou are using NiMH or NiCd battery NiMH and NiCd battery are not easy to be damaged usually you needn t worry about the over discharge problem so you can set this programmable item to No Protection 4 Timing There are many differences among structures and parameters of different brushless motors so a fixed timing ESC is difficult to compatible with all these brushless motors It is necessary to make the timing value programmable Please select the most suitable timing value according to the motor you are just using The correct timing value makes the motor running smoothly And generally higher timing value brings out higher output power and higher speed Program the ESC 1 Program the ESC with you transmitter 4 Steps are needed they are Enter program mode Select programmable item Choose the new value of the selected item Exit STEP 1 Enter the program mode Switch on the transmitter move the throttle stick to maximum position Full throttle position and then connect the battery pack to the ESC Wait for 2 seconds the motor emits Beep Beep tone Wait for 5 seconds the motor emits sisis special tone that means the program mode is entered STEP 2 Select the programmable item You will hear 4 groups of Beep tone circularly If you move the throttle stick to bottom2. position or the neutral position within 3 seconds after one kind of tones this item will be selected 1 Beep Running Mode 2 Beep Beep Lipo Cells 3 Beep Beep Beep Low Voltage Cutoff Threshold 4 Beep Beep Beep Beep Timing Forward Only Forward STEP 3 Choose the new value for the selected item After entering an item you will hear several tones in loop Set the value matching to a tone by moving the throttle stick to the maximum position Full throttle position when you hear the tone then a special tone sisis emits means the value is chosen and saved in the ESC Keep the throttle stick at the maximum position Full throttle position you will go back to step 2 and you can select other items Move the stick to bottom or neutral a position within 2 seconds will exit program mode directly Beep Page 2 Cutoff Threshod amp Backward Auto Calculate 2Cells 3Cells 4Cells 5Cells 6 Cells No Protection 2 8V Cell 3 0V Cell 3 2V Cell 3 4V Cell 3 75 Timing 0 w I 18 75 22 5 2625 STEP 4 Exit program mode There are 2 methods to exit the program 7A Program the ESC with the Program Card INote5 One long Beep 5 short Beep For example Beep Beep tone means the No 6 value 5 1 6 mode 1 In Step 3 after choosing the val
3. the throttle range setting process is finished throttle stick to the bottom position a Beep tone can be heard that means the bottom position has been confirmed Now the throttle range setting process is finished Beep Beep When the motor emits Beep tone the red LED in the ESC will flash at the same tim Beep Beep Beep Note When the motor emits Beep tone the red LED in the ESC will flash at the same time The Normal Start Process 1 Move the throttle stick to the neutral position or the bottom position and then turn on the transmitter 2 Connect the battery pack to the ESC 3 The motor emits several Beep tones to represent the cells number of your lithium battery pack Please make sure that the number is correct If only one Beep tone is emitted that means the Low Voltage Cutoff Threshold Please refer to the Programmable Items in the following form is set to No protection this is only suitable when you are using a NiMH battery pdck Please never use No protection mode for lithium battery otherwise the battery is very easy to be damaged 4 Move the throttle stick upwards the motor begins to run and speeds up The LED Status There is a red LED in the ESC the usages are 1 The LED lights when the throttle stick is moved to the maximum position full throttle 2 When setting the throttle range or setting the programmable items of t
4. easily setting the programmable items Note1 The program card is an optional equipment for the ESC YY WV VEY Specifications Class Cont Burst BEC Current rent Mode Qi i 10s gt i Normal ESC Supports 2 6 cells Lipo i Bate U vi ERS ee MARINE 25A esa p sea foinear Jeva sa es se sta mt sessio 35A__ MARINE 35A 6V 1 5A 2 3 50g ev 3A 2 6 6 18 93g 5 94 33 18 90A 180A Switch 6v 3A 2 6 6 18 989 5 94 33 18 180A MARINE 180A 180A 360A Switch 5 8V 3A 2 6 6 18 165g 05 72 68 34 High Voltage ESC Supports 5 12 cells Lipo i i ance Sh f i 80A HV_ MARINE 80A HV 94 33 18 Begin To Use The New ESC Warning For safety please always keep the propeller away from human body or any other object STEP 1 Connect the ESC motor receiver battery and servo according to the following diagram The output wires of A B C of the ESC can be connected with the motor wires freely without any order If the motor runs in the opposite direction please swap any two wire connections Battery pole Connect to throttle Black wire channel Battery pole Ch 2 4 Red wire y Receiver STEP 2 Throttle Range Setting Throttle Range Calibration In order to make the ESC fit the throttle range you must calibrate it for the following cases otherwise the ESC cannot work properly Doc Ver HW 15 HK001 090623 Page 1 Begin to u
5. he ESC the LED flashes at the same time when the motor beeps Programmable Items Note2 The italics texts in the following form are the default settings i Vale Program m able Hen s ooo To ome eea a imeem 2 cells 3oells 4oels Scells 6ceis 2 Lipo Cells Note3 Note4 Meee Scells 6clls 8cels 10cells 12cels 125 1500 z User Manual of MARINE Series Brushless Speed Controller for Boat Doc Ver HW 15 HK001 090623 Note3 The parameters in this line are available for normal voltage ESC Supports 2 6 cells lipo Note4 The parameters in this line are available for high voltage ESC Supports 5 12 cells lipo 1 Running Mode With Forward Only mode the boat can go forward but cannot go backward Forward and Backward mode provides backward function which is suitable for some specially designed boats Please read the user manual of your boat to confirm whether it is possible to run backward Note Forward and Backward mode uses Double Click method to activate the backward action When you move the throttle stick from forward zone to backward zone for the first time This is the 1 click the ESC begins to brake the motor the motor speeds down but it is still running not completely stopped so the backward action is NOT happened now When the throttle stick is moved to the backward zone again The 2 4 click if the motor speed is slowed down to zero i e
6. is emitted after 2 beep tone Beep Beep Direction of the throttle channel is reversed so the ESC has entered the program mode Set the direction of throttle channel correctly The motor suddenly speeds down even if at the full throttle situation The ESC has entered the low voltage cutoff protection mode The ESC is over heat Replace the battery pack as soon as possible Stop running the boat for several minutes to cool the ESC
7. se a new ESC Begin to use a new transmitter Change the settings of neutral position of the throttle stick ATV or EPA parameters etc gt gt gt 2 1 Turn on the transmitter set the EPA ATV value of throttle channel to 100 and disable the ABS brake function of your transmitter if it does has this function If you are using a Futaba transmitter please set the direction of the throttle channel to REV 2 2 If you are using a Flat style transmitter a Move the throttle stick to the top position that is full throttle position and then connect the battery pack to the ESC after 2 seconds Beep Beep tone can be heard that means the full throttle position has been confirmed 2 2 If you are using a Handgun style transmitter a Move the throttle stick to the maximum position that is full throttle position and then connect the battery pack to the ESC after 2 seconds Beep Beep tone can be heard that means the full throttle position has been confirmed b If you want to set it to half range please move the throttle stick to the neutral position a Beep tone can be heard that means the neutral position has been confirmed If you want to set it to full range In such a case the boat cannot run backward please move the b Release the throttle stick to the neutral position a Beep tone can be heard that means the neutral position has been confirmed Now
8. stopped the backward action will be occurred The Double Click method can prevent mistakenly reverse event 2 Lipo Cells We strongly suggest setting the Lipo Cells item manually If you choose Auto Calculate the ESC will measure the battery s voltage when it is just connected and then the ESC judges the cells number For example if the battery s voltage is lower than 8 8V it will be judged as 2 cells Lipo battery In order to let the ESC judge the cells number correctly please always use a fully charged battery to connect the ESC If the battery is partly discharged the Auto Calculate may get a wrong result Hint In the startup process the motor will emits several Beep tones to represent the Lipo cells number it is helpful for you to check whether it is coincident with the actual battery pack or not 3 Low Voltage Cutoff Threshold This function prevents the lithium battery pack from over discharging The ESC detects the battery s voltage at any time if the voltage is lower than the threshold for 2 seconds the output power will be reduced 50 Please replace the battery pack as soon as possible Warning If you ignore the low voltage cutoff phenomenon and keep running the boat the battery pack will be seriously damaged a How to calculate the cutoff threshold of a whole battery pack The cutoff threshold of a battery pack The threshold of each cell cells number For example if the threshold of each cell
9. ue the motor will emits special tone sisis move the throttle stick to the bottom position or the neutral position in 2 second to exit the program mode 2 Disconnect the ised pack Ton the Foe to exit the program mode iea Program card is an optional equipment for boat ESC it has 3 digital LEDs to show the programmable items and their values so the user interface is very friendly It is quite easy for programming the ESC with this small equipment Please read the user manual of program card Trouble Shooting for more information After power on motor does not work no sound is emitted After power on motor does not work such an alert tone is emitted beep beep beep beep Every beep beep has a time interval of about 1 second pack and ESC is not correct The connection between battery Check the power connection Replace the connector Input voltage is abnormal too high or too low Check the voltage of battery pack After power on motor does not work such an alert tone is emitted beep beep beep Every beep has a time interval of about 2 seconds Throttle signal is irregular Check the receiver and transmitter The motor runs in the opposite direction The connection between ESC and the motor need to be changed Swap any two wire connections between ESC and motor After power on motor does not work a special tone S 567i2
10. y User Manual of MARINE Series Brushless Speed Controller for Boat Thanks for purchasing MARINE series Electronic Speed Controller ESC for boat High power system for RC model can be very dangerous so please read this manual carefully Jn that we have no control over the correct use installation application or maintenance of our products no liability shall be assumed nor accepted for any damages losses or costs resulting from the use of the product Any claims arising from the operating failure of malfunctioning etc will be denied We assume no liability for personal injury consequential damages resulting from our product or our workmanship As far as is legally permitted the obligation to compensation is limited to the invoice amount of the affecta product Features i Specially designed for RC boat with excellent start up acceleration and linearity features Use top quality electronic components to enhance the current endurance ability of the ESC With water cooling system and the whole ESC is waterproof to get a longer life 2 running modes Forward Only mode and Forward Backward mode for various of boats Multiple protection features Low voltage cut off protection for lithium or hickel battery Over heat protection Throttle signal loss protection 8 steps of timing adjustment compatible with all kinds of sensorless brushl ss motor Pocket sized Program Card can be purchased separately for
Download Pdf Manuals
Related Search