Brief introduction:
Contents
1. 3 Stop Button 4 5 Button for LCD monitor inclination adjustment L 234 5 6 T T R E T DOO AO amp Picture 2 6 3 Methods of control Optional Control methods as following 1 By standardized manual film button as picture 2 2 By unit set wireless remote control you can control a lift individually 3 By grouping wireless remote control you can control five groups of lifts together at most with remote controller As picture 3 The details can be found in the instruction of remote control disembarked operation Groups indicator light fh fi fe oe Grouping remote controller Picture 3 4 By collective control Using the romote control signal sending box as picture 4 through serial communication port of computer you can make collective control on many groups of lifts by order Controlling communication is serial port connect the details can be found in centralized control setting PAGE 2 OF 5 COPY RIGHT KMP TECHNOLOGY CO LTD Receiver antenna Indicator light Green E a Red Remote control signal sending box Picture 4 5 By terminal grouping wireless remote control centralized remote control you can make control by connecting optional central control system with the help of programmed transmission control protocol the details can be found in the data pattern of RS 232 remote controller 7 Standard Accessories 1 Manual control cable and button one set 2 Power cable one item 8 S2. check power supply circuitry QTf the electrical source in gear please check whether the button tie wire loose or not The fuse is in good condition or not switch line of upstroke and stroke down are loose or not Lift still in the upper point and can not down please check whether the switch blocks or not Press both up and down buttons could not work but hear quiver sound and it is not strong Check whether the capacitor punctures or not Short circuit and the tie wire contact good or not At that time the motor will fever severely please cut out the electrical source lest burnout motor Both up and down can move but the machine emit strong noise Check transmission gear or rack if it is locked of the gear cracking Check gear and rack s joggle to make sure if mal position or not Check rack shaft liner if it is fell off or not Check gear and rack s clearance to make sure if it is supper big or not PAGE 5 OF 5 COPY RIGHT KMP TECHNOLOGY CO LTD
3. USER S MANUAL FOR A3 1 15 17 19 21 22 1 Brief introduction In order to satisfy the customer s requirement and meet the market trend we designed this brand new lift for LCD monitor It is very light and features in artistic appearance easy and convenient installation and can be efficiently controlled by one to one mode or optional integrated central controlled system This product can be adjusted the elevation angle easily to avoid the light go directly into human s eye under the principle of ergonomics to reduce eyes tiredness 2 Features Motorized control and freely up or down running God reliability and good anti shock performance Suitable for LCD monitors 15 17 19 21 22inch Automatically open and close the top panel Optional RS 232 or RS 485 communicate programming control serial ports 3 Parameter requirements LCD Size For LCD 15 the displayer less than 375X60X320mm 5KG For LCD 17 the displayer less than 395X65X350mm 5KG For LCD 17 W the displayer less than 470X65X350mm 5KG For LCD 19 the displayer less than 435X65X380mm 6KG For LCD 19 W the displayer less than 450X80X380mm 6KG For LCD 21 the displayer less than 490X85X370mm 6KG For LCD 22 W the displayer less than 520X85X370mm 6KG Power AC220V 50HZ Or custom made 4 The place to be used This product is suitable for high class multimedia meeting system surveillance system and high clas
4. ize of the lift Model number A3 1 15 Model number A3 1 17 Model number A3 1 17 W Bn 6 oJ a 636 643 o gt 495 Model number A3 1 19 Model number A3 1 19W Model number A3 1 21 PAGE 3 OF 5 COPY RIGHT KMP TECHNOLOGY CO LTD Model number A3 1 22 Remark because some light warp caused by the production procedure the actual dimension of the final product may be a little different the above dimension only for reference Please install the lift base on the size of the final product 9 Remote control debarkation operation Unit set wireless remote control Press manual film switch A W buttons synchronously at that time there is a red indicator light in the back of the case glisten gradually Then unlash the buttons Use cartridge or small screwdriver pressing the switch in the emitter hole on the back of the remote controller If the indicator light bright steadily it 1s in gear Grouping wireless remote control Press the group selection button first which light bright means the group disembarks Eliminating former controlling code the operation as follows Press manual film switch A W buttons synchronously at that time there is a red indicator light in the back of the case glisten gradually When the light glistens speedy unlash the buttons Press manual film switch A W buttons synchronously again if the indicator light bright steadi
5. ly it means the former code eliminated successfully 10 Centralized control setting Operating process Choose COM Select group rT grouping CoM X 2B Ms Log out Down Press manual film switch A W buttons synchronously at that time there is a red indicator light in the back of the case glisten gradually Then unlash the buttons PAGE 4 OF 5 COPY RIGHT KMP TECHNOLOGY CO LTD Cursor hit the button of setup learning indicator light bright steadily means the operation is ok 11 The data pattern of RS 232 remote control Set up of RS 232 COM port 2400 N 8 1 Means 2400 baud parity none 8 data bits one stop bit A data string has to send out more than 4 times continually An Log on code n 0 f 1 f are the designated group numbers n 0 means complete control Dn sd Lifting code n 0 f 1 f means the designated group numbers n 0 means complete control En sd Lowering code n 0 f 1 f means the designated group numbers n 0 means complete control 12 Malfunction and elimination When new installation or used motorized lift has malfunctioned and need to check by yourself the first thing you should do is contact with our company and then checks it after our permission An Cn Stop code n 0 f 1 f means the designated group numbers n 0 means complete control Dn En move less Check the electrical source terminal and make sure the voltage in gear or not If not you should
6. s multimedia office etc 5 Installation Measure the exact dimension of the lift And then open a conuter bore according to the size of the lift s cabinet Have all the wire connected and run the lift before installation After confirming the lift is in good running status pull out all of the connected wires VGA electrical source line manual line Put he lift into the hole and make sure to keep the surface be level Have the power wire connected Press the Up button After the supporting board rise to the top put the LCD displayer on the supporting bracket and have it screwed on the bracket Make sure all the wires connected and make sure the ground wire connected well 6 Direction for use 6 1 Illustration for the socket panel as picture 1 l power socket 1PC 2 RS485PORT 3pcs 3 red button for login the remote control Ipc PAGE I OF 5 COPY RIGHT KMP TECHNOLOGY CO LTD b aq 1 Remote control pressing the red learning button on the LCD lift meanwhile pressing the last button on the remote control releasing the learning button on the LCD lift after 2 seconds The instruction light will be turned on then releasing the last button on the remote control The antenna of the remote control is adjustable which can add the control distance 6 2 Illustration for manual film control switch pad The pad is on the top panel 1 2 Button for raising or lowering LCD monitor
Download Pdf Manuals
Related Search