ScreenBeam Mini 2 Wireless Display Receiver User Manual
Contents
1. Note There may be minor delay between the content displayed on the HDTV screen compared to the devices screen This is due to the current state of wireless display technology Extend The Extend mode creates a single extended screen between the source device and the HDTV When in Extend mode dragging windows to the right side of the devices screen displays those windows on the HDTV while dragging windows to the left of the HDTV screen displays them back on the devices screen This mode allows users to display selected content on the HDTV while all other windows remain on the device s screen When this mode is first selected the HDTV displays only the Windows desktop Second Screen Only The Second Screen Only mode causes the HDTV to be the only display for the device All content will be displayed on the HDTV the source device s screen will be blank 17 Display Options Ultra Low Delay ScreenBeam Mini 2 also supports Ultra Low Delay mode which helps reduce end to end wireless display latency Real time applications such as games can run without noticeable delay when Ultra Low Delay mode is enabled on supported devices Intel WiDi You can activate Ultra Low Delay on a device running Intel WiDi 3 5 or higher Follow the steps below to switch to ultra low delay mode 1 Launch the Intel WiDi application connect to ScreenBeam Mini 2 then click Settings 2 In the Settings screen select Current Displa2. ontec ScreenBeam Mini 2 Wireless Display Receiver Model SBWD60A User Manual Ver 1 0 Solutions for the Digital Life Table of Contents 1 Introduction Package Contents Features System Requirements 2 Connecting the Receiver Connecting to an HDTV Setting Up the First Time 3 Display and Control Options Display Mode Ultra Low Delay Restore Default Settings A Specifications B Notices Warranty GPL Info EU CE Declaration of Conformity Technical Support WwW W NNa 16 18 19 20 22 22 22 23 23 Introduction Thank you for your purchase of Actiontecs ScreenBeam Mini 2 Wireless Display Receiver The Receiver lets you wirelessly stream what s on your Intel WiDi or Miracast compatible device to your HDTV including movies videos photos music and more freeing you from squinting into a tiny screen The Receiver boasts some great features including fast setup smooth video play back full 1080p HD support ultra low delay Windows 8 1 optimization versatile compatibility and low power consumption This manual will take you through the procedures needed to install connect oper ate configure upgrade and troubleshoot the Receiver Package Contents The following items are in the ScreenBeam Mini 2 package ScreenBeam Mini 2 Wireless Display Receiver 1 USB cable 1 e HDMI extension cable 1 AC power adapter 1 Quick Start Guide Introduction Features LED In
3. Less than 4W Firmware Upgrade Wireless upgrade USB 20 ScreenBeam Mini 2 Wireless Display Receiver LED Indicator Power Certifications Wi Fi Miracast Intel WiDi Gen 4 Regulatory Compliance FCC IC UL CE ROHS2 0 TELEC NCC SRRC KCC C Tick RCM Warranty Localized to country of sale Dimensions 3 86 in x 1 18 in x 0 47 in 98 044 mm x 29 972 mm x 11 938 mm Environmental Operating temperature 0 40 Celsius 32 104 Fahrenheit Storage temperature 0 70 Celsius 32 158 Fahrenheit Operating humidity 10 85 non condensing Storage humidity 5 90 non condensing Compatibility Intel WiDi ready Ultrabooks laptops and tablets Intel WiDi 3 5 Wi Fi Miracast smartphones tablets and laptops running Windows 8 1 or Android 4 2 and higher Non WiDi Miracast ready laptops and PCs with Actiontec USB Transmitter running Windows 7 and higher Not compatible with Apple devices System Requirements Windows 8 1 or higher with Miracast support Intel WiDi capable laptop or tablet with Intel WiDi 4 and higher Wi Fi Miracast capable smartphone or tablet or laptop Note Specifications are subject to change without notice 21 Notices Warranty This product has a one year Limited Hardware Warranty and 90 day free software updates from the date of purchase Local Law This Limited Warranty Statement gives the customer specific legal rights The customer may also have o
4. be connected as shown in the figure below to HDMI Port eS Power Adapter Connecting the Receiver 5 Turn on the HDTV and set it to display the input from the correct HDMI port connected in step 1 6 Verify that the Ready To Connect screen appears on the HDTV Ready to connect Receiver name SBWD DEDC71 Firmware 5 2 2 0 Model SBWD60A The Receiver is now connected to the HDTV monitor and is ready to use Using the HDMI Extension Cable If you cannot plug the Receiver into an HDMI port on the HDTV due to other components being in the way or a poorly accessible port use the included HDMI extension cable to connect the Receiver In this case the hardware should be con nected as shown in the figure below HOMI Extension Cable ScreenBeam Mini 2 Wireless Display Receiver Setting Up the First Time This section explains how to connect ScreenBeam Mini 2 for the first time to a source device There are three source device options Windows 8 1 Intel WiDi and Miracast Windows 8 1 To connect to a source device running Windows 8 1 1 From the Windows desktop go to the Charms menu and select Devices You can also use the shortcut keys Windows logo K 2 When the Devices menu appears select Project DEE Desktop 3 P 5 Propect Connecting the Receiver 3 When the Project menu appears select Add a wireless display Windows will search for available devic
5. 13 Connecting the Receiver WiDi Software Version Support Make sure the device supports Intel Wireless Display WiDi software version 3 5 or higher To find out which version of Intel WiDi the device is running launch the Intel WiDi application and click Help then navigate to the About Intel WiDi section To obtain the latest Intel WiDi software and drivers go to http www intel com go wirelessdisplayupdate or click Check Intel WiDi website for updates co WiDi 3 z About Intel WiDi Version 4 2 24 0 nght 2010 2013 Inte Lopynght Corporation Check Intel WiDi website for updates Miracast To connect a Miracast enabled Android device to the Receiver use the following procedure For best performance the Miracast device should be running the latest software 1 Ona Miracast enabled Android device locate and open the Wireless Display Application check for the application under Settings Note The name of the Wireless Display application depends on the device type and model Refer to the devices user manual for more details 14 ScreenBeam Mini 2 Wireless Display Receiver 2 The Wireless Display application scans for available devices Select the Receiver from the device list You may be required to enter a PIN which will be displayed on the HDTV screen 3 Enter the PIN in the PIN text box then click Connect 4 Wait for the device to pair with and connect to th
6. 88 436 0657 23
7. dicator Reset Button Micro USB Port HDMI Connector Reset Button resets the Receiver to its default setting Micro USB Port for power HDMI Connector connects the Receiver to HDTV projector for video and audio output LED Indicator displays status of power supply System Requirements Display device with one Type A HDMI port Available power outlet Compatible Devices 4th Gen Ultrabook with Intel WiDi 4 or higher Smartphone tablet or laptop running Windows 8 1 Laptop or notebook computer running Intel WiDi 3 5 or higher Wi Fi Miracast certified smartphones and tablets Non WiDi Miracast ready laptops and PCs with Actiontec USB Transmitter Windows 7 or higher Connecting the Receiver This chapter details how to connect ScreenBeam Mini 2 Receiver to an HDTV monitor and how to set it up for the first time Make sure you have all the contents from the Receiver s package available before beginning the installation Connecting to an HDTV To connect Receiver to an HDTV monitor 1 Get the Receiver USB cable power adapter and HDMI extension cable from the Receiver s package 2 Plug the small male connector of the USB cable to the Power port on the Receiver 3 Plug the Receiver into an available HDMI port on the HDTV 4 Plug the large male connector of the USB cable to the power adapter and plug the power adapter to a power outlet When Steps 1 4 are complete the hardware should
8. e Receiver When it does the devices screen will be displayed on the HDTV Tips for Optimal Performance To get the most out of ScreenBeam Mini 2 note the following Keep the Receiver in line of sight in relation to the source device Doing this will help ensure the Receiver receives the best possible signal The Receivers optimal wireless range is within 30 feet of the source device However actual range and effectiveness depends on many factors including the amount of existing signal interference and the building materials used in the surrounding structure Avoid placing the Receiver near other possible sources of interference such as electric fans or other devices with electric motors microwave ovens and cordless phones 15 Display and Control Options This chapter describes the various display modes and control options that are sup ported by ScreenBeam Mini 2 Display Mode ScreenBeam Mini 2 supports three display modes when connected with a compati ble wireless display application Intel WiDi or Windows 8 1 Project for example In Windows press the Windows logo P keys simultaneously to launch the dis play options and select the desired display mode from the options Computer only Duplicate Extend Projector only a E EE pu 16 ScreenBeam Mini 2 Wireless Display Receiver Duplicate The Duplicate mode is used to display the same content on both the devices screen and the HDTV simultaneously
9. es Project To project connect a display cy Second screen Note If the device is running Windows 8 1 and the previous screens do not appear go to http www actiontec com widi81 to update the software Alternatively the Windows 8 1 device can be updat ed via the Windows Update application ScreenBeam Mini 2 Wireless Display Receiver 4 A PC and devices screen appears Click Devices and from the list that appears select the Receiver Television SBWD ODSS9A SEWDIDOA Actiontec A353 SBWDID0A Acthontec DA37 SBWDIOOA m Actiontec E879 SEWD1I00A Connecting the Receiver 5 The Windows 8 1 device connects to the Receiver Connecting to SB WD DEDC71 SBWD60A Follow any instructions on your television 6 The HDTV displays a message to show the status of the connection ScreenBeam Connecting you now Receiver name SBWD DEDC71 mware 2 2 0 Mode SBWD60A Actiorkec ScreenBeam Mini 2 Wireless Display Receiver ScreenBeam Magic is about to happen Receiver name SBWD DEDC71 5 2 2 0 Model SBW 7 When the last screen above is displayed the device has connected to the Receiver The devices screen should be displayed on the HDTV Intel WiDi To connect to a source device running Intel WiDi 1 Launch the Intel Wireless Display application on the device To find the application go to Windows Search on the device and search for Intel WiDi 2 The appl
10. ges of the device screen cannot be seen on the HDTV screen or there are black around the picture ScreenBeam Mini 2 s cropping settings can be adjusted To do this 1 From the Intel WiDi application click Settings The Settings screen appears Settings General Current Display Settings Picture and Sound 12 ScreenBeam Mini 2 Wireless Display Receiver 2 Inthe Picture and Sound section select Adjust cropping cr Laz Settings Picture and Sound To change the arrangement of your display press P on your keyboard Extended video mode will enable full 1080p HD Aciust cropping if you cannot see the edges of your computer screen on the wireless display Get Help for picture problems Get Help for sound problems Jett earehens Geekery soured gt he woken hered ue On yout sweter Papir ered compan Play Sample ene WiDi WZ Settings Adjust Edge Visibility If your computer screen does not look correct on the wireless display you may need to adjust the size If your picture is too small you will see black borders around the edges of the wireless display Increase the size of the picture using the plus button if your picture is too big the picture will extend off the edge of the wireless display Decrease the size of the pre using the minus button Tig Look at the Start menu in the lower left hand comer and use the pictures below to help you tune your display
11. ication scans for available receivers automatically Select the Receiver and click Connect The Connect Automatically checkbox is optional If the Receiver is not listed click Scan Intel WiO o 5 a Actiontec DA8F Connect Automaticalh Availabh SBWD100A A y vailable BwD1 MA G A Actiontec A353 Availabk BWD100A lA We Actiontec 7058 Available SBWD100A li A Connecting the Receiver 3 Wait until the Receiver displays a PIN on the HDTV and a PIN entry box is displayed on the screen of the WiDi device Enter the PIN in the PIN entry box on the WiDi device then click Continue ScreenBeam Enter PIN 5027 823 7 Receiver name SBWD DEDC71 2 0 Model SBWD60A To finalize the connection please enter the PIN code from your Wireless Display 12345670 10 ScreenBeam Mini 2 Wireless Display Receiver 4 The HDTV displays messages to show the status of the connection ScreenBeam Connecting you now Receiver name SBWD DEDC71 Firmware 5 2 2 0 Model SBWD60A ScreenBeam Magic is about to happen Receiver name SBWD DEDC71 Firmware 5 2 2 0 Model SBWD60A 11 Connecting the Receiver 5 A Connection Successful screen appears on the device s screen Click Finished and the device s screen is displayed on the HDTV F Intel Wid lo st eae WiDi PZ Connection Successful intel st Learn more about advanced features Adjusting the HDTV Picture If ed
12. ther rights which vary from state to state in the United States from province to province in Canada and from country to country else where in the world To the extent that this Limited Warranty Statement is inconsistent with local law this Statement shall be deemed modified to be consistent with such local law Under such local law certain disclaimers and limitations of this Warranty Statement may not apply to the customer Go to http www actiontec com products warranty php for more information GPL Info For GNU General Public License GPL related information go to http opensource actiontec com 22 ScreenBeam Mini 2 Wireless Dispay Receiver EU CE Declaration of Conformity To obtain the complete Declaration of Conformity form in softcopy go to the Actiontec Electronics Declarations of Conformity EU EEA website at http international actiontec com support doc The symbol below is placed in accordance with the European Union Directive 2002 96 on the Waste Electrical and Electronic Equipment the WEEE Directive If disposed of within the European Union this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive Technical Support Go to http www actiontec com sbupdate for product support updates and more information including Firmware updates Troubleshooting Registration FAQs Technical Support Phone Number United States 1 8
13. y Settings Fi htela Wi 1o35 tae ee WiDi P7 Settings Current Wireless Display Wireless Display Name Actiontec DA amp F Connect automatically to this wireless display Quality vs Speed For games Choose speed For photos presentabons and most other uses Choose Quality Prioritize Image Quality Prioritize Speed Apply Settings Register your Actiontec Electronics Inc ScreenBeam Pro Education Edition1 0 0 0 wireless display for support and updates Wireless Display Detailed Info 18 ScreenBeam Mini 2 Wireless Display Receiver Restore Default Settings To restore the Receiver s factory default settings 1 Power on the Receiver and wait for the Ready to Connect screen to appear 2 Hold down the Reset button on the Receiver 3 When the Resetting to Factory Defaults screen appears on the HDTV release the Reset button The Receiver reboots When it completes this operation it will be running with its default settings 19 Specifications Model Number SBWD60A Languages English French German Korean Japanese Simplified Chinese Traditional Chinese and Spanish A V interface HDMI Type A female connector Video Output Up to full HD 1080p30 H 264 Audio Output LPCM 2 channel stereo Wireless 802 11 a b g n dual band 2 4 amp 5 GHz Security WPA2 WPS virtual PBC AES 128 bit Content Protection HDCP 2 x for HDMI Electrical Input 5V 1A micro USB Consumption
Download Pdf Manuals
Related Search