USER MANUAL - Davis Instruments Corp.
Contents
1. Insert the 1 4 x 3 lag screws through the metal backing plate and the holes in the mounting base into the post Make sure the base is level by checking the built in bubble level 4 Tighten the lag screws using an adjustable wrench or 7 16 wrench Installing the Rain Collector on a Pole Installing the Rain Collector on a Pole Accessories for Pole Mounting e Use the Mounting Tripod 7716 for easy roof mounting e Use the Mounting Pole Kit 7717 to raise the installation height of the rain collector by up to 37 5 0 95 m General Guidelines for Installing on a Pole e With the supplied U bolt the rain collector can be mounted on a pole having an outside diameter ranging from it to i a 32 44mm A larger U bolt not supplied can be used to mount to a pole with a maximum outside diameter of 21a 64mm To mount on a smaller pole obtain a U bolt that fits the base openings but that has a shorter threaded section If the included U bolt is used with a smaller pole the bolt will interfere with the rain collector cone e Use the built in bubble level to ensure rain collector is level Refer to the following illustration when installing the rain collector on a pole 1 4 Hex Nut 1 4 Lock Washer am Backing Plate Groove for U Bolt Rain Collector Base 1 While holding the mounting base against the pole place the two ends of a U bolt around the pole and through the two holes in2. ING Hex MECHANISM Nuts W Backing aa Gen Bubble we J Plate Bird Spikes 16 K T Ne Metric Rain i M E gt Adapter S last BASE 40 Cable Prepare the Rain Collector Tools and Materials Needed You may need some of the following tools and materials to install the rain collector e Drill with 3 32 2 mm drill bit e Medium Phillips screwdriver 3 16 or 5 mm wrench e Cable clips or weather resistant cable ties with screw holes or other means for mounting Rain Collector Internal Components Hole in Base Bid a Can be used to thread cable out and down Tipping Spoons L Magnet A Adjustment Reed Switch 9 A Screw TK gN Adjustment Bubble Guide Level Restraining Drain Screen Cable Slot Note The rain collector is shipped with the 40 cable coiled and exiting through one of the cable slots You may want to uncoil the cable and feed it down through the hole in the base behind the tipping spoon Prepare the Rain Collector 1 Remove the cone from the base by rotating the base until the latches on the cone line up with the latch openings in the base then lifting the cone away from the base Twist off the rain collector cone Prepare the Rain Collector 2 Carefully cut and remove the plastic tie Tipping Spoons which holds the tipping spoons in place during shipping Plastic Tie Optional Insert the Metric Rain Adapter The rain collector tipping spoon mec
3. USER MANUAL Rain Collector with Mountable Base Product numbers 7857 and 7857M DAVIS E Davis Instruments 3465 Diablo Avenue Hayward CA 94545 2778 U S A 510 732 9229 www davisnet com Rain Collector 7857 amp 7857m This rain collector can be used with Vantage Pro2 weather stations including Vantage Pro2 Vantage Pro2 Plus and the Anemometer Sensor Transmitter Kit The following instructions assume the rain collector is being used with a Vantage Pro2 or Vantage Pro2 Plus Integrated Sensor Suite ISS Refer to the user manual that came with your station for more information Manuals are available online at www davisnet com in the Weather Support section Note Model number 7857 is factory calibrated to take rain measurements in 0 01 inches The metric version of the rain collector number 7857M comes factory calibrated to take measurements in 0 2 mm Components Please make sure you have all listed components before continuing e Rain collector cone latched onto base e Base with tipping mechanism and 40 12 m cable U bolt backing plate and 2 each lag screws flat washers lock washers and hex nuts e Debris Screen 16 3 5 9 cm bird spikes optional HARDWARE KIT 14 Bird Spike Sockets RAIN lt gt CONE Debris Screen fits snugly Fi Gri inside cone Mee ee 1 4 x 3 Lag Screws 1 4 Flat 6 x 75mm J Washers 1 4 Lock Washers TIPP
4. ain The metric version is calibrated so the spoons tip for each 0 2 mm To adjust the calibration slightly use a 3 16 or 5 mm wrench to rotate the adjustment screws which are located underneath the tipping spoons See Rain Collector Internal Components on page 2 The adjustment guide embossed in the platform shows how far you must rotate both screws in turn to effect a 1 and a2 change Moving the screws in the positive direction causes the spoons to tip more times i e give a larger count for a given amount of water Modify both adjustment screws by the same amount To check the accuracy of the rain collector compare the Davis rain collector with a tube type rain gauge Use a rain gauge with an aperture of at least 4 inches Any smaller and the readings obtained may not be accurate Place the tube type rain gauge directly next to the Davis rain collector Compare the totals on three storms to determine whether your rain collector needs calibration and by how much Adjust the screws to fine tune the reading for the next three storms if necessary Note Avoid comparison to rainfall readings obtained from television radio newspapers or neighbors readings Such readings are not an accurate measurement of the weather conditions in your specific location The rain collector is carefully tested at the factory to conform to the specifications listed in the back of this manual Maintaining the Rain Collector For grea
5. hanism takes measurements in 0 01 US versions or 0 2 mm M EU UK and OV increments for each tip of the spoons If you have a US version and would like to convert it to a metric measurement you can insert the metric adapter that is included in your hardware kit Or if you have a metric version and wish to convert it to take measurements in 0 01 you can reverse these steps to remove the factory installed metric adapter Note Inserting the metric rain adapter converts the rain collector to take measurements in 0 2 mm increments for each tip of the spoons The console or Vantage Connect must be configured to 0 2 mm as well See your console or Vantage Connect user guide for more information To install the metric adapter 1 Find the metric adapter included in the hardware 2 Locate the magnet between silver colored V shaped arms of the tipping spoons 3 Open the arms slightly with one hand while pulling the magnet out with the other Prepare the Rain Collector 4 Separate an end cap from one end of the magnet we e7 5 Slide the magnet exposed a Top closed end of magnet first into the open slot of the metric adapter SF Bottom notched 6 Insert the metric adapter and magnet between the arms of the spoons with the top solid side of the metric adapter facing up Test the Rain Collector Before installing the rain collector test the unit If you are replacing a rain collector you prev
6. ions Red seca v eke ated eendaiee aad Switch terminal Green amp Yellow Switch terminal Product Number 7857 Rain Collector Part Number 07395 335 Rev C 11 3 15 This product complies with the essential protection requirements of the EC EMC Directive 2004 108 EC Copyright 2015 Davis Instruments Corp All rights reserved Davis Instruments Quality Management System is ISO 9001 certified Information in this document is subject to change without notice DAVIS Eil Davis Instruments 3465 Diablo Avenue Hayward CA 94545 2778 U S A 510 732 9229 Fax 510 732 9188 E mail info davisnet com www davisnet com
7. iously installed make a note of the total rainfall amount displayed You may want to reenter this amount after you test the rain collector 1 Open the transmitter shelter on the ISS Remove the foam insert and feed the rain collector cable up through the opening Plug the cable to the appropriate connector in the sensor interface See illustration on page 6 2 Press the RAINpDay button on your console to display rainfall 3 While watching the display on your console to see if it changes slowly tip the bucket until it drops to the opposite side Each tip indicates 0 01 or 0 2 mm of rain It may take up to a minute for the first tip to register at the console If the display does not change you may be tipping the bucket too quickly Try again more slowly this time If the rainfall amount displayed on the console increases by the expected increment either 0 01 or 0 2 mm each time you tip the bucket your rain collector is working properly Installing the Rain Collector Installing the Rain Collector If you have not already done so separate the cone from the base and disconnect the rain collector cable from the sensor interface in the transmitter shelter Choosing a Location for the Rain Collector Keep the following in mind when choosing a location for your rain collector e For accurate readings you must mount the rain collector so that it is level A bubble level is built in to the base to simplify this process The rai
8. n collector contains a magnet operated switch which may not operate correctly if you mount the rain collector on or near any object which is attracted to a magnet e Exposure to winds can reduce the measured rainfall amounts Mount the rain collector where there are no obstructions of rainfall at low angles such as trees houses fences and as low as possible out of the wind e Choose a location which is easily accessible for normal cleaning and is distant from trees or other sources of heavy pollen or debris Note Climbing on your roof may be hazardous If you are uneasy about installing your unit please have a qualified professional complete the installation Davis specifically disclaims any liability for injury or loss resulting from the installation or use of the rain collector Installing the Rain Collector on a Post or Flat Surface Installing the Rain Collector on a Post or Flat Surface Refer to the following illustration to install the rain collector on a post or flat vertical surface Fi Ss y Sy S For clairty the tipping mechanism is not shown 1 4 x 3 4 Lag AR 40 Cable 1 With a 3 16 5 mm drill bit drill two holes approximately a 54 mm apart Use the metal backing plate as a guide when marking the holes and a carpenter s level to ensure the holes are level 2 Remove the rain collector cone if it is installed 3
9. reen prevents large bits of debris from blocking the funnel hole If bird nesting is a problem you can place a spike in the hole on top of the debris screen i i Note that using a bird spike in the debris screen may make the screen more likely to be blown over or out in a high wind gust Nw Be careful bird spikes may be sharp Note If you choose not to install the bird spikes we recommend that you keep the packet of spikes in case birds become a problem in the future 6 To prevent fraying or cutting of the cable where it is exposed to weather it is important that you secure it so it doesn t whip about in the wind Use cable clips or weather resistant cable ties to secure the cable Place clips or ties approximately every 3 to 5 feet 1 to 1 6 m Do not use metal staples or a staple gun to secure cables Metal staples especially when installed with a staple gun have a tendency to cut the cables Adjusting the Rain Collector Extending Cable Runs If the cable length supplied with the rain collector is not long enough for your purposes you may extend it The maximum length of cable is 900 feet 274 m To extend the cable purchase standard 4 Conductor Extension Cables from Davis and connect them to the existing rain collector cable Adjusting the Rain Collector Note The non metric version of the rain collector is calibrated at the factory so the spoons tip and records rainfall for each 0 01 of r
10. test accuracy you should thoroughly clean the rain collector at least once or twice a year 1 Disconnect the rain collector cable from the sensor interface in the transmitter shelter 2 Separate the cone from the base 3 Use a soft damp cloth to clean pollen dirt and other debris from the cone cone screens and bucket 4 Use a pipe cleaner to clear the funnel hole in the cone and the drain screens in the base When all parts are clean rinse with clear water 5 Reattach the cone and replace the debris screen Reconnect the rain collector cable to the sensor interface Troubleshooting Guide Rainfall is not registering on the console or the console has a large error e Check the cable connections from the sensor to the console Cable connections account for a large portion of the potential problems Connections should be firmly seated in the jacks and plugged in straight If a reading appears intermittently on the display as you jiggle the cable the connection is faulty e Make sure there is no magnetic steel or iron object near the rain collector e Make sure the funnel hole in the cone is clear so water can empty into the spoons e Make sure the spoons move freely when tipping to both sides The console should show an increase in rainfall for each tip of the spoons If the spoons do not move at all check that you have cut the cable tie that holds them in place during shipping e Make sure the rain collector is mounted so
11. that it is level Contacting Davis Technical Support If you have any questions about your rain collector please contact Davis Technical Support We ll be glad to help 510 732 7814 Monday Friday 7 00 a m 5 30 p m Pacific Time 510 670 0589 Technical Support FAX support davisnet com E mail to Technical Support info davisnet com General e mail www davisnet com Davis Instruments website Specifications Sensor Type 20 000 Tipping bucket with magnetic reed switch OuIpUT gicen fie nea a au aa tod Steere Contact closure Attached Cable 40 12 m 4 conductor 26 AWG Connector 200000 Modular connector RJ 11 Recommended Max Cable Length 900 270 m Housing Material UV stabilized ABS plastic Dimensions with base no spikes 9 25 wide x 10 25 high x 11 deep 23 5 x 26 x 28 cm Collection Area o oo uoun 33 2 in 214 cm Range Daily Rainfall 0 00 to 99 99 0 0 mm to 999 8 mm Total Rainfall 0 00 to 199 99 0 0 mm to 6553 mm ACGUIACY orr nanara Eea For rain rates up to 2 hr 50 mm hr 4 of total or 0 01 0 2mm 0 01 one tip of the bucket whichever is greater For rain rates from 2 hr 50 mm hr to 4 hr 100 mm hr 5 of total or 0 01 0 2mm whichever is greater Update Interval 0 20 24 seconds Input Output Connect
12. the base 2 Slide the metal backing plate over the bolt ends as they stick out toward the rain collector cone Secure the backing plate with a washer a lock washer and a hex nut on each of the bolt ends Adjust the height of the rain collector then tighten the nuts Finishing Steps Finishing Steps 1 Open the transmitter shelter on the ISS Remove the foam insert and feed the rain collector cable up through the opening Plug the cable to the appropriate receptacle in the transmitter Replace the foam and close the shelter Transmitter Shelter Sensor Interface 2 To be certain the rain collector is functioning properly after installation retest the unit See Optional Insert the Metric Measurement Adapter on page 3 3 To use bird spikes insert one spike into each socket around the rim of the cone The sockets are tapered push firmly or tap lightly with a hammer for a more secure fit 4 Place the cone back onto the base by putting the latches on the cone into the latch openings in the base and rotating the cone clockwise until the latches lock into place As you reattach the cone make sure to run the cable to the cable slot in the base or the rte cone will not fit snugly against the base You may a aa a also run the cable down through the hole in the base mot 5 Place the debris screen pointed end up into the cone The sc
Download Pdf Manuals
Related Search