StarBoard Link EZ2-Pen User`s Guide
Contents
1. 7 Star Board software If the No connection icon in below appears on the Tasktray it means that the StarBoard is not connected Make sure that the StarBoard and the PC are properly connected If the StarBoard is properly connected the icon changes to Connected as above If the icon does not change despite correcting the connection there may be some other problem For details refer to 4 Appendix Troubleshooting on page 4 1 of this User s Guide If the positions of the pen tip and cursor are out of alignment select MENU on the StarBoard Software toolbar Settings StarBoard Calibrate and then perform position alignment 3 2 English StarBoard Link EZ2 Pen How to use Important Run the Adjusting the Sensor See page 2 6 to 2 9 of this User s Guide when operated for the first time and whenever the board is moved Not doing so may cause operation errors 3 2 2 Start Method Mac version 1 Connect the USB cable of digitizer to the computer 2 Turn on the power switch of the projector 3 Turn the computer power switch on to startup Mac 4 Adjust the position of the projector so that the Mac screen projected by the projector is within the input area refer to page 1 3 of this User s Guide 5 Select Go Applications StarBoard Software to start StarBoard Software 6 Select MENU on the StarBoard Software toolbar Settings StarBoard Check Connect2. and lighting status of the LED Lit green Normal Flashing orange Recognizing StarBoard Lit orange Error has occurred 6 Cable Holder Used to fix the USB cable in place 3 Projection area Input area Characters or images drawn in this area are imported into the PC 1 3 English StarBoard Link EZ2 Pen Assembly and Setup 2 Assembly and Setup Be sure to follow the precautions below when installing the StarBoard Important Use on a flat surface This product is designed so that stable input is achieved when used on a flat surface Do not use on an uneven or curved surface NWARNINGS Install this product on a vertical surface Do not install on a slanted surface or ceiling Failure to comply may cause the stand to fall resulting in personal injury or may cause damage to this product due to shock of impact from the board falling If magnets are not used to install this product fix it in place with screws Failure to comply may cause the stand to fall resulting in personal injury or may cause damage to this product due to shock of impact from the board falling NOTICE Select a level and stable position Do not set it up near equipment that might generate electromagnetic waves or radio frequencies such as radio transmitters televisions copying machines or air conditioners Avoid locations that are dusty that are subject to extremely high or low temperatures or humidity or that are expo
3. 2 9 English StarBoard Link EZ2 Pen How to use 3 How to Use 3 1 How to Use The Pen To use the pen to draw letters or images press the tip of the pen to the projection area and move the pen Remove the tip of the pen from the projection area to finish writing Keep in mind the following points when using the pen 1 When drawing with the pen hold the pen perpendicular to the projection area as much as possible and continue pressing the pen tip to the projection area to draw Holding the pen diagonally may cause input to not be detected properly 2 Reflective materials for detecting input are used in the silver part of the pen tip If you hold the reflective part and draw letters or images the pen s input may not be detected properly If the letters or images you draw on the projection area are not detected properly change the way you are holding the pen and check if they are displayed properly 3 1 English StarBoard Link EZ2 Pen How to use 3 2 Start Method 3 2 1 Start Method Windows version 1 Connect the USB cable of digitizer to the PC 2 Turn on the power switch of the projector 3 Turn on the power switch of the PC to start Windows 4 Adjust the position of the projector so that the Windows screen projected by the projector 1s within the input area refer to page 1 3 of this User s Guide 5 Select Start All Programs StarBoard Software or double click the StarBoard icon on the desktop
4. N CAUTIONS What to do in case of emission of smoke strange odor or strange noise If an abnormal condition such as emission of smoke strange odor or strange noise happens to occur for some reason immediately disconnect the product s USB cable from the PC Confirm that the smoke or strange odor is no longer being emitted and contact a support center to request repairs Continued operation without repair may result in fire What to do if the product breaks or the USB cable is damaged If this product breaks or the USB cable becomes damaged for some reason immediately disconnect the USB cable from the PC and contact a support center Continued operation without repair may result in emission of a strange odor or smoke 3 Precautions Regarding Handling J N CAUTIONS Do not splash with water or chemical compounds Do not place this product in a location subject to contact with water droplets or place any containers containing water or other chemical compounds on top of or nearby this product Failure to comply may result in damage or fire if water or chemical compounds get inside this product 6 English StarBoard Link EZ2 Pen Safe Handlin NOTICE Disconnect the USB cable during extended periods of non use For safety reasons disconnect the USB cable if the product is not going to be used for an extended period of time Failure to comply may result in malfunction Handle the connection cable properly Impro
5. 2 Sensor Adjustment Procedure Mac VersiOn cscceccesceecesceecesceeceececesceceseeeeceseeseneees 2 8 220 POSIMOMING AONE saroian E a IN 2 9 SHOWT USC A ia ad 3 1 a Ios O 3 1 LS Mei e a io 3 2 3 201 Start Method WindOWS Version iaa do 3 2 322 stant Method Mac Versi n ica 379 SAPPE AIK reor aE E N aS eure ee aah EEEE oes 4 1 A O a O gota Ot eat tah ea eats cakes 4 A DOSY SUCIM PEA AOS de aed ie al 4 4 Ao Proper Carranco tdo 4 5 o Nee er re TO eR Re ene eee ee ee 4 5 AS Product Warranty DOE ieo ida 4 6 12 English StarBoard Link EZ2 Pen Introduction 1 Introduction 1 1 Preparations This chapter describes the preparations to be made before using StarBoard First time users of StarBoard should read through this chapter 1 1 1 Product Outline In order to use the StarBoard Link EZ2 Pen a digitizer are installed on an existing whiteboard or flat wall surface After setting up the provided software on a PC that is connected to a projector you can use the pen to operate the projected PC screen or import characters or images drawn on the projection area in real time to the PC 1 1 2 Features You can use the pen to operate the PC You can use the pen to operate the PC screen projected onto the board with the projector You can write directly onto the PC screen After installing the provided StarBoard Software onto a PC you can use the pen to write characters or images directly onto the PC screen The input characters or dra
6. message that says Digitizer adjustment has finished successfully is displayed After this calibration 1s performed so please wait StarBoard Adjust Tool Digitizer adjustment has finished successfully If you want to start the calibration program please wait Cancel If you do not want to calibrate press the Cancel button 4 The calibration screen starts Use the pen to click on the center of the flashing circles in order Continue pressing the pen to the center to a circle until it turns from red to green If clicking is performed properly the circle turns grey Hold the pen upright to the installation surface p p p Srarticard Link 172 Press Esc bey or Sale Button of Pen to abort Touch the center of the binhing mark with the pen tip P p p p Once you click on the center of all nine circles a dialogue box that says Calibration completed is displayed Press OK to finish calibration This completes sensor adjustment 2 7 English StarBoard Link EZ2 Pen Assembly and Setup 2 2 4 2 Sensor Adjustment Procedure Mac version 1 Start SBAdjust When first connected via USB it starts automatically Start Go Applications StarBoard Lsadrv folder SBAgdjust 2 Touch the center of the blinking mark with the pen tip Hold the pen upright to the installation surface Do not move the pen until the display in the progress bar reaches 100 2 5 Adjust t
7. place in locations subject to excess moisture dust smoke or steam Placement in a location such as next to a kitchen or a humidifier may result in fire or damage to this product Do not use this product near water If water somehow gets inside this product immediately disconnect the USB cable and contact a support center Continued use may result in fire or damage to this product 8 English StarBoard Link EZ2 Pen Safe Handlin NOTICE Do not use this product in locations subject to high temperature or high humidity This product s usage environment conditions Temperature 5 C 35 C Humidity 20 RH 80 RH no condensation Do not set up in locations subject to vibration and or shock of impact Vibration and or shock of impact may harm internal components of this product resulting in damage to it Do not set up this product in a location subject to vibration or shock of impact Do not set up this product near a high voltage line or power source If this product is set up near high voltage lines or power sources it might receive interference Do not set up in a location subject to direct sunlight or near a heater Failure to comply may result in deformation of or damage to this product 6 Precautions Regarding Disposal NOTICE At time of disposal handle this product as industrial waste according to all applicable laws and regulations When disposing of this product the user should follow all laws an
8. the warranty is not presented If specified fields on the registration card accompanying the warranty are not completed or if the wording has been changed without authorization The warranty applies only to the original purchasers It does not apply to a third party to whom the customer resold this product In the event of a malfunction or damage resulting from the customer s improper handling e g a fall impact etc caused by the customer during transportation or movement In the event of problems resulting from handling contrary to the handling and precautions mentioned in this user s guide In the event of failure or damage resulting from abnormal voltages pollution or other natural disasters e g fire earthquake and lightning In the event of a malfunction in this product caused by the connection to this product of equipment other than the equipment specified by our company In the event that there is no abnormality in this product but a defect in a part other than this product was detected or remedied In the event of ordinary wear and tear wear deterioration etc of consumables even during normal use 4 6 English StarBoard Link EZ2 Pen Appendix gt 10 If this product malfunctions review the contents of this user s guide If the problems remain irreparable contact the dealer The dealer will determine whether or not the product must be repaired so please contact them If the customer sends the
9. you installed this product in an environment that might affect its operation Other than the above 4 3 Please check page 3 1 of this user s guide How to Use The Pen and try to input again with the correct way of holding the pen Perform Adjusting the Sensor on page 2 6 of this user s guide and check if you can perform input Please check the contents of the notification on page 11 of this user s guide and if there is an applicable item please take the appropriate measures Restart Windows Mac OS or Check if the same problem arises when using another pen If operations are normal when using another pen the original pen is the problem English StarBoard Link EZ2 Pen Appendix 4 2 System Specifications Digitizer resolution 0 05mm Sampling rate Approx 100 points second when using USB1 1 Full Speed Interface USB 1 1 cable length 6m Effective screen size Digitizer 510mm W x75 5mm H x41mm D Pen 140mm x 915mm Weight Digitizer 0 8kg Pen 15g Dimensions Power consumption 5V 500mA Operating requirements 5 C 35 C Humidity 20 80 RH without condensation Storage requirements 10 C 45 C Humidity 20 80 RH without condensation Standards etc VCCI Class A FCC Class B CE Using infrared and compact cameras this product captures the image reflected light of a pen and detects the corresponding coordinate position Do not operate near lighting that will ob
10. you very much for purchasing Hitachi Solutions s StarBoard Link EZ2 Pen henceforth referred to as StarBoard This User s Guide has been created for people who already have a working knowledge of personal computers henceforth referred to as PC Please make sure that you understand the contents of this User s Guide and use the software correctly We hope that you make the most of this product 3 English StarBoard Link EZ2 Pen Safe Handling Markings and Symbols Various markings and symbols are used in this User s Guide and on this product to ensure the safe and correct use of this product and to prevent personal injury and property damage These symbols and their meanings are as explained below Understand the information well before reading the body of the User s Guide This is a Safety Warning symbol This symbol will appear to raise the attention of the user to existing risks that may cause harm to people To avoid any chances of injuries or possibly death DO NOT IGNORE the safety instructions that follow this symbol JN WARNINGS This warning will appear where there exists a risk of death or fatal injuries N CAUTIONS This warning will appear where there exists a risk of moderate or light injuries NOTICE This warning will appear where there exists a risk of damage to property A This symbol draws attention to cautions including warnings This symbol indicates something prohibited 0 This sym
11. StarBoard Link EZ2 Pen User s Guide Read this User s Guide and carefully retain it for future reference Before using this product carefully read and fully understand the safety instructions Store this User s Guide nearby for ease of reference SBLE2P ML120801 StarBoard Link EZ2 Pen Notices Reproduction or reprinting without permission of this User s Guide or any part thereof is prohibited The contents of this User s Guide are subject to change without prior notice Every effort has been made to ensure that this User s Guide is complete and correct However should any questionable points mistakes etc come to your attention please inform the vendor Hitachi Solutions Ltd assumes no responsibility for losses resulting from or related to the use of this product Refer to 4 Appendix 4 5 Product Warranty Policy at the end of this User s Guide for details on the warranty and liabilities Precautions Regarding Disposal At time of disposal handle this product as industrial waste according to all applicable laws and regulations Special Instructions This manual contains explanations relating to accessories that are sold separately as well as the product itself Disclaimers Hitachi Solutions Ltd assumes no liability and makes no warranty either express or implicit regarding the contents of this User s Guide Also the company makes no warranty as to the product s suitability merchantability or fitness for a p
12. able connection AAA Did you start the system in the Start the system in mina correct correct sequence sequence For details on starting the system see page 3 2 of this In case that USB cable extended as When connecting to the PC use the bellow it may result in unstable of bundled USB extension cable product working If you need to extend USB cable USB extension cable other than juse self powered USB hub bundled one Bus powered USB hub USB extender StarBoard Software files may be Uninstall the StarBoard Software broken or installation may not be jand then re install it complete correctly For details on installing StarBoard Software see the StarBoard Software Installation Guide Other than the above Contact a support center 4 1 English StarBoard Link EZ2 Pen Appendix Recognition Related Problems What to check What to do The controller must be reset Disconnect the USB cable and and the system restarted reconnect it If this does not solve the problem restart the PC In case that USB cable When connecting to the PC use the extended as bellow it may bundled USB extension cable result in unstable of product If you need to extend USB cable use working self powered USB hub Touch Sensor Error USB error Touch Sensor Error Insufficient USB USB extension cable other than bundled one Bus powered USB hub USB extender Is a high speed USB device Be sure to connect the StarB
13. articular intended use All products of Hitachi Solutions Ltd described in this User s Guide are presently for sale or are site licensed Users who purchased the aforesaid product s will bear the costs of all required services repairs and damages resulting from defects in this product and will bear the costs of direct or indirect damages including the loss of profits or required information that resulted from the product defects Moreover Hitachi Solutions Ltd retains the right to revise this User s Guide and to modify the contents thereof without any obligation to notify anyone l English StarBoard Link EZ2 Pen Product Assurance Provisions This product 1s limited to use in the country where the user bought this product For warranty details refer to 4 Appendix 4 5 Product Warranty Policy at the end of this User s Guide This second edition of the user s guide SBLE2P ML120801 1s for the following products AH00336 StarBoard Link EZ2 Pen Overseas model Windows is a trademark of Microsoft Corporation U S and in other countries Mac and Mac OS are trademarks of Apple Inc registered in the U S and other countries Other trademarks and product names are trademarks and or registered trademarks of their respective holders Manual Creation Dates August 2012 second edition SBLE2P ML120801 All Rights Reserved Copyright c 2012 Hitachi Solutions Ltd 2 English StarBoard Link EZ2 Pen Introduction Thank
14. bol indicates something that must be done 4 English StarBoard Link EZ2 Pen Safe Handlin 1 Precautions Regarding Operation J N WARNINGS Do not make modifications Do not make any adjustments repairs or modifications not given in this User s Guide as doing so may lead to personal injury or damage to the product Do not open or remove cover of this product Failure to comply may lead to personal injury or damage to the product Refer internal inspections adjustments and repairs to your dealer or support center Do not place objects on top of this product If a foreign object falls on top of or inside this product it may lead to personal injury or damage to the product N CAUTIONS In order to prevent damage by static electricity touch a nearby metal object with your hand to discharge any static electricity before touching this product Static electricity from your body may cause damage to this product NOTICE When connecting to the PC use the bundled USB extension cable If you use a USB extension cable other than bundled one it may cause malfunction Do not place heavy objects on pull on or subject the USB cable to excess heat Failure to comply may result damage to the USB cable Always grasp the plug of the USB cable when connecting or disconnecting Pulling on the USB cable may result in scratching or damage to the cable 5 English StarBoard Link EZ2 Pen Safe Handlin 2 Dealing with Trouble
15. d regulations of the locality in which it is being used 9 English StarBoard Link EZ2 Pen Safe Handlin Careful thought was given to the cautions on this device and in this User s Guide However unanticipated circumstances might occur When operating this product users themselves must exercise caution as well as follow instructions NWARNINGS Page s Install this product on a vertical surface Do not install this product on a slanting surface or ceiling Otherwise the equipment might fall possibly resulting in injury or the impact might cause product failure If magnets are not used to install this product fix it in place with screws Otherwise the equipment might fall possibly resulting in injury or the impact might cause product failure 10 English StarBoard Link EZ2 Pen Safe Handling NOTICE Notice Contents Page s Select a level and stable position Do not set it up near equipment that might generate electromagnetic waves or radio frequencies such as radio transmitters televisions copying machines or air conditioners Avoid locations that are dusty that are subject to extremely high or low temperatures or humidity or that are exposed to direct sunlight The gap between the cursor and pen will become big in the lower 13cm 5 inches of the digitizer If you want to reduce the gap place the digitizer keeping a minimum space of 13cm 5 inches from the upper part of the centre of th
16. e projection area Using infrared and compact cameras this product captures the image reflected light of a pen and detects the corresponding coordinate position Do not operate near lighting that will obstruct the capture of the image Locations where the surface or side of the projection area are exposed to direct sunlight Locations in which there are light fittings with many light bulbs or infrared rays directly above the projection area The place where there is some reflective object around projection area Reflective bars or pen which is not used interactive white board built in reflection tape etc 11 English StarBoard Link EZ2 Pen Contents jun Contents AN GPOCUCUION td tl a a a a a aa 1 1 BEP DA OS eaaa E A hel aaa 1 1 APO UC UAM A e da 1 1 A A oie acca neice a Cena gBions se sen TE eu 1 1 MD Parts MCC Ke ddr det eta e 1 2 ESA Sat Oak AAA A O A deeb T toe anes Saeed 172 La Role Of Wain Pare aeoaea E E ciaa 1 3 ad A en PCa e man et Neer ment OST TNT aiciete Perr eit ee eT eee 1 3 ASS EM ANC SPUD RA AS a 2 1 Zel Instatline the StarBoard Software tasa iii 2 2 22 Ist n o hie DECS indi ci 2 2 22041 Projection Irom the Project a ree usta ve dette ahaaela uterus 2 2 22 sta Mins TMS DIO AOL A amnaca eed 2 3 22 5 Connechine the USB Cables ias 2 4 222 4 AUS the AE A meee aes 2 6 2 2 4 1 Sensor Adjustment Procedure Windows version ccecceeceecescecesceeceseeecesceeceeceseseneees 2 6 2 2 4
17. g coordinate position Do not operate near lighting that will obstruct the capture of the image Locations where the surface or side of the projection area are exposed to direct sunlight Locations in which there are light fittings with many light bulbs or infrared rays directly above the projection area The place where there is some reflective object around projection area Reflective bars or pen which are not used interactive white board built in reflection tape etc 2 2 4 1 Sensor Adjustment Procedure Windows version 1 Start SBAdjust exe When first connected via USB it starts automatically Select MENU Settings StarBoard StarBoard Settings and press Sensor adjustment in the StarBoard toolbar Alternatively Run SBAdjust exe located under My Computer C Drive Program Files Hitachi Software Engineering FX DUODriver This folder path may be changed since it depends on your Windows installation 2 Touch the center of the blinking mark with the pen tip Hold the pen upright to the installation surface Do not move the pen until the display in the progress bar reaches 100 2 5 Adjust the Digitizer Touch the center of the blinking mark with the pen tip Hold the pen upright to the installation surface Press Esc key to abort 1 2 6 English StarBoard Link EZ2 Pen Assembly and Setup 3 Once the sensor adjustment is properly completed a
18. he Digkines Touch the center of the blinking mark with the pen tip Hold the pen upright to the installation surface Press Esc key to abort O 1 i 2E ths 3 Once the sensor adjustment is properly completed a message that says Digitizer adjustment has finished successfully is displayed After this calibration is performed so please wait StarBoard Adjust Tool Digitizer adjustment has finished successfully If you want to start the calibration program please wait Cancel If you do not want to calibrate press the Cancel button 2 8 English StarBoard Link EZ2 Pen Assembly and Setup 4 The calibration screen starts Use the pen to click on the center of the flashing circles in order Continue pressing the pen to the center to a circle until it turns from red to green If clicking is performed properly the circle turns grey Hold the pen upright to the installation surface 0 p p p Saerfeerd Link 172 Press Esc bey or Sale Button of Pon to abort Touch the center of the blinking mark with the pen tis p P P 4 5 p Once you click on the center of all nine circles a dialogue box that says Calibration completed 1s displayed Press OK to finish calibration This completes sensor adjustment 2 2 5 Positioning Alignment Select MENU on the StarBoard Software toolbar Settings StarBoard Calibrate OK and then perform position alignment
19. ion and then check the connection If the StarBoard is not connected message appears StarBoard Software has not detected the StarBoard Check whether the StarBoard and PC are connected properly PS StarBoard is connected sl StarBoard is not connected ee a t oe Y II A If they are connected properly the StarBoard is connected message appears If the indication does not change even though you have checked the connection there is likely to be some problem For details see 4 Appendix Troubleshooting on page 4 1 in this user s guide 3 3 English StarBoard Link EZ2 Pen How to use If the positions of the pen tip and cursor are out of alignment select MENU on the StarBoard Software toolbar Settings StarBoard Calibrate and then perform position alignment Important Run the Adjusting the Sensor See page 2 6 to 2 9 of this User s Guide when operated for the first time and whenever the board is moved Not doing so may cause operation errors 3 4 English StarBoard Link EZ2 Pen Appendix 4 Appendix 4 1 Troubleshooting Before assuming the product is broken be sure to check adjustments proper handling procedures the possibility of faulty cable connections etc Recognition Related Problems What to check What to do The StarBoard does not Is the USB cable connected to the Connect the USB cable to the PC recognize input PC Is the status LED AAA 1 3 lit the USB c
20. oard and connected to the USB host any high speed USB devices to controller used to connect the separate USB host controllers StarBoard In case that PC only has one USB host controller use self powered USB hub Input Related Problems What to check What to do The input position does not match The position cannot be aligned properly Has position alignment been Perform proper position alignment performed properly Other than the above Contact a support center Have the StarBoard and Adjust the position of the StarBoard projector been placed in the and the projector If undue correction proper orientation is performed it may not be possible to align the position properly Is the PC screen being projected Make sure the PC screen projection is inside the StarBoard s input contained within the StarBoard s input area area For details on the input area see page 1 3 of this User s Guide StarBoard Software files may Uninstall the StarBoard Software and then re install it For details on installing StarBoard Software see the StarBoard Software Installation Guide Other than the above Contact a support center be broken or installation may not be complete correctly 4 2 English StarBoard Link EZ2 Pen Input Related Problems Appendix What to check What to do The pen does not Are you holding the pen operate or its operation properly is unstable Did you perform sensor adjustment Have
21. pen a soft wet cloth with a mixture of water and the cleaner and wipe Never use a solvent such as thinner Do not allow the pen tip to get wet 4 4 Replaceable Parts 1 Pen Reflective Pen For details on obtaining them contact your dealer or a support center 4 5 English StarBoard Link EZ2 Pen Appendix 4 5 Product Warranty Policy 1 During the free warranty service period if a malfunction occurs during normal use the malfunction will be corrected without charge according to the provisions of the warranty Furthermore if the customer registration card accompanying the warranty is not returned to our company the customer information will not be registered so free repairs might be unavailable After receiving this product please immediately fill out and return this customer registration card 2 The warranty coverage 1s listed in the following table Product Name Warranty Coverage StarBoard Link EZ2 Pen USB extension cable Pen Reflective Pen Es Explanatory note Covered by warranty However this excludes abrasion physical damage and loss Not covered by warranty 3 Please refer to the warranty sheet for this product s warranty service period 4 Even during the warranty period there will be a repair charge in the following cases 1 2 3 4 5 6 7 8 9 10 If the registration card accompanying the warranty is not returned to our company If
22. per handling of the connection cable such as jamming it against a wall undue bending pulling or twisting may result in overheating or damage due to exposure of the conductive core electrical short or severing of the cable 4 Precautions Regarding Moving the Product NOTICE Always disconnect the USB cable from the PC when moving this product Failure to comply may result in damage to the USB cable and or the product itself Do not subject to shock of impact This product is a precision instrument Excessive shock of impact may hinder further operation Take extreme care when moving this product 7 English StarBoard Link EZ2 Pen Safe Handlin 5 Precautions Regarding Setup Environment J N WARNINGS Do not place in a location with flammable or corrosive gas Placing this product in a location where there is flammable or corrosive gas may result in fire or damage to this product There is a particular danger of explosion in the case of flammable gas Do not place in a location with flammable or corrosive gas Install this product on a flat surface Installing this product on an uneven surface such as bumpy or curved surfaces may cause the product to operate improperly or fall over resulting in personal injury or product malfunction N CAUTIONS Do not touch internally mounted parts Directly toughing internally mounted parts inside this product may result in personal injury or damage to this product Do not
23. product to our company without RMA Return Merchandise Authorization number it might not be covered by warranty As a rule the customer is responsible for shipping charges required to send all or part of the product for repair etc Our company will assume responsibility for the return shipping to the customer This warranty does not cover labor fees for repair associated equipment assembly or disassembly Incidental damage caused by the failure of this product e g loss of profit that should have resulted from the use of this product is outside the scope of this warranty The aforementioned provisions define this warranty and they supersede those of all express or implied warranties that include legal defect liability This warranty is limited to use of this product within the country where the user bought this product 4 7 English
24. rea and install so it is parallel with the edge of the projection area Center D gt Digitizer ee 5 cm 2 inches Projection Area After installing the digitizer check to make sure does not slide down due to its own weight and that it is securely installed Installing to walls where magnets cannot be used 1 Fix the wall mount bracket on the back of the digitizer with 2 machine screws a Machine screws 2 3 English StarBoard Link EZ2 Pen Assembly and Setup 2 Align the center of the digitizer with the center of the projection area 5 cm 2 inches above the projection area and install so 1t 1s parallel with the edge of the projection area Digitizer pl 5cm 2 inches Wood screws Center D gt f i i Projection Area 2 2 3 Connecting the USB Cable 1 Install the cable holder and then hook the USB cable into the holder to fix it in place Cable holder USB cable Fixing Screws When installing onto a wall where magnets cannot be used fix the cable holder with wood screws 2 4 English StarBoard Link EZ2 Pen 2 Connect the bundled USB extension cable to the computer 2 5 Assembly and Setup USB extension cable English StarBoard Link EZ2 Pen Assembly and Setup 2 2 4 Adjusting the Sensor NOTICE Using infrared and compact cameras this product captures the image reflected light of a pen and detects the correspondin
25. sed to direct sunlight 2 1 English StarBoard Link EZ2 Pen Assembly and Setup 2 1 Installing the StarBoard Software Before Starting to Connect Equipment Install the StarBoard Software on your PC before starting to connect equipment The equipment might not operate correctly if 1t is connected without the software being installed About PC Earth Depending on your PC an incorrect operation might be caused by PC noise via the USB cable If this happens verify that the earth of your PC s power supply cable is connected If the earth is not connected 1t might cause an incorrect operation 2 2 Installing the Devices NOTICE The gap between the cursor and pen will become big in the lower 13cm 5 inches of the digitizer If you want to reduce the gap place the digitizer keeping a minimum space of 13cm 5 inches from the upper part of the centre of the projection area 2 2 1 Projection from the Projector Project the computer screen using the projector To install the StarBoard ensure the following clearance is maintained around the projection area However the StarBoard detectable sizes are as shown below Aspect ratio 4 3 16 10 60 90 inches 13cm 5 inches Projection Area 2 2 English StarBoard Link EZ2 Pen Assembly and Setup 2 2 2 Installing the Digitizer Installing with Magnets Align the center of the digitizer with the center of the projection area 5cm 2 inches above the projection a
26. struct the capture of the image This includes Locations where the surface or side of the projection area are exposed to direct sunlight Locations in which there are light fittings with many light bulbs or infrared rays directly above the projection area The place where there is some reflective object around projection area Reflective bars or pen which is not used interactive white board built in reflection tape etc Depending on installation conditions or sensor property position detection may be off by about 20 mm 4 4 English StarBoard Link EZ2 Pen Appendix 4 3 Proper Care and Cleaning Clean the StarBoard periodically so that you may use it for a long time to come 1 Digitizer Cleaning When cleaning the digitizer use a soft cloth dampened with a diluted neutral cleansing agent that does not contain a polishing compound Never use a solvent such as thinner Note that rubbing or striking the StarBoard surface with a finger nail or other hard object may result in scratching 2 Cleaning the Magnets Use a soft cloth dampened with water or alcohol to remove dirt from the magnet sections of the digitizer Do not use cleaners etc that contain surfactant as doing so will reduce the retaining force of the magnets 3 Cleaning the pen To clean the pen use a diluted neutral cleansing agent that does not contain a polishing compound Do not apply the neutral cleansing agent directly but rather dam
27. wn images are imported as digital data in real time into the PC where they can be saved or printed Compatible with PowerPoint presentations Characters or images can be written into presentations created with Microsoft PowerPoint which significantly improves the expressive power of the presentations You can also write on video images For Windows Characters or images can be written onto captured video image displays This makes it easy to use video materials in lessons or presentations 1 1 English StarBoard Link EZ2 Pen Introduction 1 2 Parts Check After unpacking make sure that all the following parts are present 1 2 1 StarBoard 1 Parts y Digitizer O 2 Pen Reflective Pen o Cable holder Wood screws p pid Machine screws Wall mount bracket StarBoard Software DVD ROM StarBoard Software Startup Guide StarBoard Link EZ2 Pen Startup Guide 11 Warranty Sheet 4 5 6 D 8 9 10 11 D A AZ 1 2 English StarBoard Link EZ2 Pen Introduction 1 3 Role of Each Part 1 3 1 StarBoard 6 2 en a i 5 6 Aspect ratio 4 3 16 10 60 90 inches StarBoard Link EZ2 Pen Installation Image 1 Digitizer 4 Pen Receives information regarding characters or Used in pen input images drawn with the pen and transmits this 5 USB extension cable Ane Used to connect the StarBoard with the PC 2 Status LED The connection status is displayed by the color
Download Pdf Manuals
Related Search