PDF version - ARM Information Center
Contents
1. 12 Copyright 2000 ARM Limited All rights reserved ARM DGI 0006A 9 1 9 2 9 3 9 4 Evaluator 7T Installation Guide References This section provides references to further information ARM documentation Evaluator 7T User Guide ARM DUI 0134 ARM Developer Suite Debugger Guide ARM DUI 0066 ARM Developer Suite Debug Target Guide ARM DUI 0058 ARM Developer Suite Developer Guide ARM DUI 0056 ARM Developer Suite Getting Started ARM DUI 0064 ARM Developer Suite CodeWarrior IDE Guide ARM DUI 0065 ARM Developer Suite Tools Guide ARM DUI 0067 ARM Multi ICE User Guide ARM DUI 0048 Recommended website Documentation section and Development Support section on the ARM website http www arm com Recommended books ARM Architecture Reference Manual edited by Dave Jaggar ISBN 0 13 736299 4 ARM System Architecture by Steve Furber ISBN 2 201 40352 8 Further reading Samsung KS32C50100 Embedded Network Controller User s Manual v0 3 ARM DGI 0006A Copyright 2000 ARM Limited All rights reserved 13 Page intentionally blank Replace with cover artwork2. refer to the online help provided with the software or to the ARM Developer Suite Debuggers Guide This is located in the directory in which you installed ADS for example c ADS100 Pdf 10 Copyright 2000 ARM Limited All rights reserved ARM DGI 0006A Evaluator 7T Installation Guide 7 Further Information An email list server is provided by ARM so that you can share information with other Evaluator 7T users To subscribe send an email to subscribe evaluator7t arm com The list server will reply welcoming you to the Evaluator 7T email group You can query other Evaluator 7T users by sending email to evaluator7t arm com To unsubscribe send an email to unsubscribe evaluator7t arm com For additional information on CodeWarrior IDE and AXD use the online help provided with ADS ARM DGI 0006A Copyright 2000 ARM Limited All rights reserved 11 Evaluator 7T Installation Guide 8 Warranty Information The Evaluator 7T has been sold without any warranty including without limiting the implied warranties of merchantability non infringement and fitness for a particular purpose The Evaluator 7T is provided without support In the case of a faulty component ARM will replace that item or the complete unit depending on the severity up to 60 days from the date of purchase The provision in this section shall constitute ARM s exclusive liability and sole remedy for any and all damages resulting from the use of the Evaluator 7T
3. of ADS all the tools and documents for the board 2 Copyright 2000 ARM Limited All rights reserved ARM DGI 0006A Evaluator 7T Installation Guide 2 3 Setting up the Evaluator 7T hardware The Evaluator 7T is supplied with a 9 pin to 9 pin straight through serial cable If you have a 25 pin connector on your PC a 9 pin to 25 pin male to female straight through adapter is required To set up the Evaluator 7T hardware 1 Connect the serial cable between the COM1 Debug port on the Evaluator 7T and the host PC Make a note of the serial port that you use This is important when you use the debugger 2 Connect the power adapter to the power connector on the Evaluator 7T 9V nominal center pin positive 3 Connect the power adapter to the power socket The yellow LED on the seven segment display lights to indicate that the power is on 4 Press the System Reset button on the Evaluator 7T The four general purpose LEDs flicker and the green LED D1 remains on This indicates the board has been initialized and is working correctly Refer to the ADS Developer Guide directory C ADS100 Pd the Evaluator 7T User Guide and the Multi ICE User Guide for more information 2 4 Initialization information When the Evaluator 7T is powered on or reset initialization code sets up the board For ARM processor based boards initialization is performed by HAL and the Angel debug monitor When initialization is complete the board is ready to
4. 6A Copyright 2000 ARM Limited All rights reserved T Evaluator 7T Installation Guide 10 11 12 13 14 Setup serial connection HE Serial Port COM1 z Baud Rate 57600 ba Cancel This is the list of baud rates available on Help the host Ifthe selected value is not also available on the target a compatible value will be selected automatically Figure 4 Setup serial connection dialog Set the serial port to the COM port you used on the host PC see Setting up the Evaluator 7T hardware on page 3 Set the buad rate to 38400 Click on the OK button in the Setup serial connection dialog Click on the OK button in the Remote_A connection dialog In the Choose Target dialog ensure that the ADP option is highlighted and click on the OK button AXD starts to download the image to the Evaluator 7T Note If this fails select the Configure Target option from the Options menu of AXD and reconfigure the COM or baud rate You are now ready to run the Pascal s Triangle example on the Evaluator 7T Copyright 2000 ARM Limited All rights reserved ARM DGI 0006A Evaluator 7T Installation Guide 5 Running the Sample Application It is asumed that you have completed the steps described in Building a Sample Application on page 4 and Downloading the Image on page 6 To start the Pascal s Triangle example from AXD 1 Select Go from the Execute menu The program stops at the main C function 2 Select Go ag
5. Application Debugging an Application Further Information Warranty Information References Evaluator 7T Installation Guide 1 Introduction This booklet introduces the Evaluator 7T ARM evaluation board The Evaluator 7T allows you to quickly familiarize yourself with the tools environments and products available from ARM It enables you to work through the stages required to build an ARM based embedded system To assist you the Evaluator 7T package includes several example applications for you to compile link download debug and extend In addition to this document the Evaluator 7T package contains ARM Developer Suite ADS Free Evaluation Version v1 0 1 or later CD ROM ARM Evaluator 7T Board Tools and Documentation CD ROM 9 pin straight through RS 232 serial cable Evaluator 7T board 9V power adapter Caution If you already have a full version of the ADS do not install the ADS evaluation CD ROM supplied with the Evaluator 7T 1 1 ARM Developer Suite CD ROM The CD ROM contains an evaluation version of ADS Evaluation ADS is a fully functional software development toolkit that times out 45 days after installation It requires Microsoft Windows 95 98 NT 4 0 or Windows 2000 See the CD ROM packaging for system requirements and installation instructions 1 2 ARM Evaluator 7T Board Tools and Documentation CD ROM This CD ROM contains an assortment of tools documentation and ex
6. Page intentionally blank Replace with cover artwork Copyright 2000 Proprietary Notice ARM the ARM Powered logo Thumb and StrongARM are registered trademarks of ARM Limited The ARM logo AMBA Angel ARMulator EmbeddedICE ModelGen Multi ICE PrimeCell ARM7TDMI ARM7TDMI S ARM9TDMI ARM9E S ARM946E S ARMQ66E S ETM7 ETM9 TDMI and STRONG are trademarks of ARM Limited All other products or services mentioned herein may be trademarks of their respective owners Neither the whole nor any part of the information contained in or the product described in this document may be adapted or reproduced in any material form except with the prior written permission of the copyright holder The product described in this document is subject to continuous developments and improvements All particulars of the product and its use contained in this document are given by ARM in good faith However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded This document is intended only to assist the reader in the use of the product ARM Limited shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product Contents Introduction Setting up the Software and Hardware Building a Sample Application Downloading the Image Running the Sample
7. ain The LEDs on the Evaluator 7T flash once and the console window of AXD displays the following Pascal s Triangle I B03 1 14641 FI I IR IO IIR IO IR IO IR IO IR IO IRR IKK Rk NOTE Close the debugger and Reset the board FI II IR IO I IR IO I RR IO IR IO IR IO I RIOR OR RK Rk ARM DGI 0006A Copyright 2000 ARM Limited All rights reserved 9 Evaluator 7T Installation Guide 6 Debugging an Application To debug the sample application follow only steps 1 and 2 of the download procedure again see Downloading the Image on page 6 Then from AXD 1 Select Go from the Execute menu The program stops at the main function 2 Scroll up to the pascal_triangle function in the Executing pascal c window 3 Click on the line containing for j 1 j lt depth j 4 Select Toggle Breakpoint from the Execute menu 5 The for j 1 j lt depth j line has a red dot At this point the Evaluator 7T board lights D1 D2 and D3 LEDs 6 Select Go again from the Execute menu The debugger executes all the lines of code between the current point and the breakpoint When the breakpoint is encountered the debugger halts the program Only D1 and D2 are active 7 Select Variables from the Processor Views menu All the local variables in the pascal_triangle function are displayed 8 Select Go from the Execute menu The program continues until completion Note For more information about AXD Debugger
8. ample application source code specific to the Evaluator 7T board The contents of this CD ROM include the following PDF documents Evaluator 7T Installation Guide ARM DGI 0006 ARM Evaluator 7T User Guide ARM DUI 0134 Samsung KS32C50100 Embedded Microcontroller User s Guide v0 3 or later ARM DGI 0006A Copyright 2000 ARM Limited All rights reserved 1 Evaluator 7T Installation Guide 2 Setting up the Software and Hardware This section guides you through the steps necessary to prepare to work with the ARM Evaluator 7T 2 1 Installing the Evaluator 7T tools and documentation To install the Evaluator 7T tools and documentation 1 Place the Evaluator 7T Tools and Documentation CD ROM into the CD ROM drive The tools and documentation installation software automatically loads and executes If this is not the case select Run from the Start menu and enter F setup exe where F is your CD ROM drive 2 Select the drive and directory into which the software is to be installed For example c Evaluator7T 3 Follow the displayed prompts to complete the installation procedure 4 Now follow the installation procedure for the ADS Evaluation Version as described in Installing the ADS evaluation software 2 2 Installing the ADS evaluation software Refer to the CD ROM packaging for instructions on how to install the ADS Evaluation Version When the installation is complete you have installed a working evaluation version
9. communicate with the host PC For the Evaluator 7T a bootstrap loader is preloaded into the flash memory so that when the board is powered on or reset the bootstrap loader initializes the board If the initialization is successful a green LED on the board is constantly lit indicating that the Evaluator 7T is ready for a program image to be downloaded ARM DGI 0006A Copyright 2000 ARM Limited All rights reserved 3 Evaluator 7T Installation Guide 3 Building a Sample Application The following procedure describes how to build a sample application using CodeWarrior Integrated Development Environment IDE from Metrowerks supplied with Evaluation ADS 1 2 Start CodeWarrior from the Windows Start gt Programs gt ARM Developer Suite menu When CodeWarrior has loaded select Open from the File menu option The Open dialog window is displayed Find the Pascal s Triangle example which is located in the same directory as the Evaluator 7T tools and documentation for example c Evaluator7T source examples pascal Select the project file pascal filename pascal mcp from the pascal directory Press the Open button A project window is displayed with the title pascal mcp see Figure 1 Bpascal mcp olx Link Order Targets DebugPel jQHrv Se File CdS Crd Data MJ M ledh 0 pascal c 540 D e ka Figure 1 Project window Copyright 2000 ARM Limited All rights reser
10. s to be configured at least once before it can be used Figure 2 Choose Target dialog 3 In AXD click on the Add button 4 Select remote_a d11 from the Open dialog box This installs the driver that is used to communicate with the Evaluator 7T 5 Inthe Choose Target dialog ensure that ADP Remote_A d11 is selected and then click on Configure The Remote_A Connection dialog is displayed 6 Click on the Select button The Available Connection Driver dialog box is displayed 6 Copyright 2000 ARM Limited All rights reserved ARM DGI 0006A Evaluator 7T Installation Guide 7 Select the ARM serial driver then click on OK button 8 The Remote_A Connection dialog is displayed see Figure 3 Remote_A connection 2 x Remote connection driver Name PPM serial driver May 99 Filename raserialdriver dll Description Remote_A Serial driver 1999 ARM Ltd ommunications driver for use with Angel Debug Monitor Configuration serial port COM1 selected speed 57600 actual speed 9600 Configure Heartbeat r Channel Viewers M Enabled C Enabled Disabling heartbeat will disable host timeout and packet resend r 4 Add Endian n G Litle C Big There is no need to specify the endianness of Angel targets Figure 3 Remote_A Connection dialog 9 Now click on the Configure button The Setup serial communication dialog box is displayed see Figure 4 on page 8 ARM DGI 000
11. ved ARM DGI 0006A Evaluator 7T Installation Guide 6 Select the Make option from the Project menu The Pascal s Triangle is compiled and linked You can now download the debug image of Pascal s Triangle to the Evaluator 7T board as described in Downloading the Image on page 6 Note For more information about CodeWarrior refer to the online help provided with the software or to the ARM Developer Suite CodeWarrior IDE User Guide This is located in the directory in which you installed ADS for example c ADS100 Pdf ARM DGI 0006A Copyright 2000 ARM Limited All rights reserved 5 Evaluator 7T Installation Guide 4 Downloading the Image When you download an image you transfer the code in the debug image from your host PC to the Evaluator 7T The image can then be executed under the control of the ARM eXtended Debugger AXD After building the image as described in Building a Sample Application on page 4 1 Press the System Reset button on the Evaluator 7T board 2 From CodeWarrior select Debug from the Project menu to download the Pascal s Triangle example image This launches the ARM eXtended Debugger AXD The Choose Target dialog box is displayed see Figure 2 Choose Target BE r Target Environments Help remote_a dill Add _Bemove_ Configure G Please select a target environment from the above list or add a target environment to the list Note that a target environment ha
Download Pdf Manuals
Related Search