Home

V670 Series User`s Manual - Products

1. Chemicals That May Cause Discoloration Swelling etc ABS resin Epoxy resin Hydrochloric acid alcohol freon sodium hydroxide hydrogen peroxide benzine sulfuric acid 10 RT nitric acid 10 RT phosphoric acid 85 RT liquid ammonia Sulfuric acid 10 RT nitric acid 10 RT hydrochloric acid 30 RT acetic acid 50 RT nitric acid calcium hydroxide benzene creosol alcohol microhexanone toluene xylene benzine and grease Chemicals That Do Not Affect ABS Resin or Epoxy Resin ABS resin Ammonia kerosene mineral oil developer YUSHIROKEN Ammonia hydrochloric acid 10 RT potassium hydroxide S50 CHEMICOOL Z VELOCITY NO 3 YUSHIROKEN EEE petroleum gasoline YUSHIROKEN S50 CHEMICOOL Z 30Y petroleum grease acetic acid nitric acid calcium VELOCITY NO 3 and YUSHIROKEN EEE 30Y hydroxide phosphoric acid 30 RT hydrochloric acid 10 RT and potassium hydroxide Epoxy resin 417 The above results are from tests conducted at room temperature 23 C Even if the chemicals do not affect the ABS or e epoxy resins at room temperature they may affect the resins at higher or lower temperatures Always contact the man er ufacturer of the chemicals and check the chemicals carefully in advance a suonipuo Buneado uo peseg ejeg sonsuapeieyy KEETeITISEL Electromagnetic Inductive RFID System 82 User s Manual SECTION 6 Appendices Memory Map Tag
2. 3 When the CF Reader Writer is within the communications area the data in the Tag s internal memory will be read and displayed on the Handy Terminal Electromagnetic Inductive RFID System User s Manual SECTION 3 Functions 44 Communications Designation Function 30 44 Setting Operating Parameters 31 Auto Command Abort Time 31 Write Verification 31 4 Memory Check Function 32 Write Protection 33 Electromagnetic Inductive RFID System User s Manual 29 uoljouny uoneubiseg suomneoiunululo2 EX e TREEL 30 SECTION 3 Functions Communications Designation Function The CF Reader Writer automatically detects Tags for the communications commands given in the following table Symbol Name Description Single Auto command After the Single Auto command has been received a communication is executed when a SA i no Tag is detected in the communications area and a response is returned Repeat Auto command The operation specified under SA is repeatedly executed The CF Reader Writer commu RA nicates only once with each Tag even if that Tag continues to be in the communications area Communications Designations SA RA SA and RA automatically detect Tags and communicate with them CF Reader Writer A oA as Communications are started when a Tag enters the communications area E SA Designation When the Single Auto command SA is specified command processing is complete
3. End Code List SECTION 4 Commands Type End code Name Description Normal end 00 Normal end Command execution has ended correctly Host 10 Parity error A parity error has occurred in the characters in the command o o 11 Framing error A framing error has occurred in the characters in the command RU 12 Overrun error An overrun error has occurred in the characters in the command 14 Format error The command format is incorrect The character interval exceeds the set time 18 Frame length error A command string longer than 300 characters was received Tag 70 Communications error An error occurred during communications with a Tag and the communications communications could not be completed normally sel 71 Verification error The correct data could not be written to the Tag only possible when verification is enabled 72 No tag error There is no Tag in the CF Reader Writer communications area 7A Address designation The designated processing address is not suitable and the execution is error impossible 7D Write protection error Data was written to a write protected page 7E Lock error Write was specified for a locked area 7F2 Tag error Communications were attempted with a Tag for which communications are 1 Communications between the CF Reader Writer and the Handy Terminal are called host communi cation 2 7E lock error and 7F tag error are most likely Tag errors If these errors o
4. Power Supply Use the power supply specified in this manual il zi p 68 Installation Always turn OFF the power supply to the Handy Terminal before inserting or removing the CF Reader Writer To protect the system from damage due to static electricity use a wrist strap or other means of preventing static dis charge when touching signal wires for terminals or connectors nsert securely into the CF Port 5 Cleaning Do not use any thinner Resin material and case paint are dissolved by thinner 6 Communications Power is supplied when opening the COM port on the CF Reader Writer Wait for at least 500 ms after opening the COM port before starting communications Electromagnetic Inductive RFID System User s Manual esf 1994102 10J suonne oeJd iyu Introduction 1 2 About this Manual 8 S Meaning of Visual Guides S o RU 5 a Indicates precautions to be observed in operating the product advice on operating methods and important information for main o taining product performance CHECK o 3 E Ne 2 l a Indicates the page numbers where related information can be found Indicates information related to troubleshooting Electromagnetic Inductive RFID System 6 User s Manual Introduction CONTENTS Introduction 2 Standard Conformity 4 About this Manual 6 SECTION 1 Product Outline 9 Features 10 Part Names and Functions 11 System Configuration 12 Applic
5. Electromagnetic Inductive RFID System User s Manual 23 SIBAOD 9A1 39101g RANe IES 3 Secure the Protective Cover to the Handy Terminal with the four M2 screws provided with the Protec tive Cover 11 Tighten the mounting screws to a torque of 0 15 N m or less CHECK Electromagnetic Inductive RFID System User s Manual SECTION 2 Communications Preparations Setting Handy Terminal Communications Conditions 1 Set the same communications conditions for the Handy Terminal and the CF Reader Writer The default settings for the CF Reader Writer are as follows Baud rate 38 400 bps Data bits 8 bits Parity even Stop bits 1 bit vw For Handy Terminal operating procedures refer to the operating instructions provided by the manufacturer i a Refer to Interface Specifications for details on the communications settings for the CF Reader Writer CHECK A p 68 Interface Specifications W suonipuo2 suoHPaIUNUUOJ euruJo Apuey Bumes AJE Electromagnetic Inductive RFID System User s Manual 25 G NOILOAS 1S9 suoneoiunuiuo2 26 SECTION 2 Communications Preparations Communications Test Procedure for Trial Operation Turn ON the power Visually check operating status indicator Check communications between Handy Terminal and CF Reader Writer using a Test Test online using command Handy Terminal p 27 Testing Communications between Handy Terminal and CF Reader Writer Ch
6. The communications distance 50 without metal is 10096 c 3 4 E 0 30 8 uo 20 o t 10 9 a 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Distance between Tag and metal mm SUO IpUOD Bunejedo uo paseg ejeg sonsuoejoeJeu KETTE Metal Tag Z CF Reader Writer Distance be Communi tween Tag cations and metal distance behind gt A 1Y Using the above information as reference carry out preliminary tests or take other appropriate measures to ensure proper installation z CHECK Electromagnetic Inductive RFID System User s Manual 81 SECTION 6 Appendices Chemical Resistance of Tags Chemicals that affect Tags are shown below ABS resin is used for case material and epoxy resin for filling material Refer the following lists and do not use chemicals that effect ABS and epoxy resin Use only chemicals that do not effect these resins Tags cannot be used in applications with explosion proof specifications Chemicals That Cause Deformations Cracks etc ABS resin Trichlene acetone xylene toluene gasoline creosol methylene chloride phenol microhexanone aqua regia chromic acid sulfur 90 RT methyl ethyl ketone aniline nitrobenzene monochlorobenzene pyridine nitric acid 60 RT and formic acid 80 RT Epoxy resin Aqua regia chromic acid sulfuric acid 90 RT nitric acid 60 RT liquid ammonia acetone methylene chloride phenol and trichlene
7. jl A p 43 Data designation Specifies the size of the write data B Bytes W Words 2 bytes Antenna designation Always 1 Write area start address The address in the Tag for writing data is specified in four hexadecimal digits Specification range 0000h to 007Fh Write area end address The end address in the Tag for writing data is specified in four hexadecimal digits Specification range 0000h to 007Fh Write data Data written to Tags Set one byte of hexadecimal if B is specified under Data designation two bytes if W is specified Response Command End code Retry Status code DF 00 flag flag CR 2 2 1 1 2 Example Writing Fill Data OOFF from Address 0000h to 007Fh Single Auto Writing 2 Bytes Send data DFSAW10000007F00FFXx CR Receive data DF0000x CR The volume of data communications with the Handy Terminal can be reduced by writing fill data to a specified area so 3 A the use of this command can improve the efficiency of the system z CHECK Electromagnetic Inductive RFID System User s Manual SPUBLWILUOD suomneoiunuluilo EANe IRE 47 SECTION 4 Commands Memory Check MD Calculates the check code for the specified block using the polynomial X16 X12 X5 1 and verifies the result against the check code attached to the check block Command Communica Proc Antenna Check block start No of check tions desig ess designa address bl
8. Mounting Hole Dimensions Two R0 8 Two 3 2 dia M3 screw holes Two R0 2 20 5 0 1 Two R0 2 Standard mounting holes Reference Unit mm plane suoisuauiig pue suoneoyioods EMTEC Electromagnetic Inductive RFID System User s Manual 71 suoisueuiig pue suoneouyioeds TNSTRETS SECTION 6 Appendices E V670 A81 Attachment for V670 D13F01H Tag The communications range of a Tag will be reduced when Tags are attached to metal objects The V670 A81 Attachment is specifically designed for V670 D13F01H Tags When combined with this Attachment V670 D13F01H Tags retain their original communications range even when installed on metal objects Target Tag model V670 D13F01H e Dimensions 28 6 Mounting Hole Dimensions 20 5 0 1 Two 3 2 dia M3 Two 3 2 dia M3 screw holes Reference plane 20 510 1 Standard mounting holes Unit mm Material PPS resin e Mounting Method Place the attachment on the reference plane of the Tag and adjust its position until the mounting holes are aligned Secure it with M3 screws a17 Tighten the M3 screws to a torque of 5 N m max e z CHECK e General Specifications Conforms to Tag specifications e Effect of Metal behind Tags Use of this Attachment increases the distance between the Tag and the metal surface to 6 mm Refer to Influence of Metal behind Tags Reference before using the Attachment UR p80 Electromagnetic Inductive RFID
9. code CW 00 flag flag x CR spueululio suoneoiunuluo KA TeTEeE ES mj 2 2 1 1 Specified number of bytes Results data Returns the calculation results data written to the Tag The data before the calculation was performed will be returned if addition gives an overflow or subtraction gives an underflow The status flag will be 1 in these cases Example Writing 2 Bytes of Data the Result of Subtracting the Subtraction Data 0002 from 0010 the Data Starting at Address 0001h Single Auto Initial Value 0010 Send data CWSAS10001020002 CR Receive data CWO0000000E CH v This command performs hexadecimal calculations so specify hexadecimal for all data being handled Also set the cal A culation area so that it is contained within one page If the calculation area is not contained within one page a com mand error will occur CHECK UA p 83 Memory Map a Electromagnetic Inductive RFID System 46 User s Manual SECTION 4 Commands Data Fill DF Writes one or two bytes of the same data to a specified Tag area The write data is specified in hexa decimal Command Communica Data Antenna Write area Write area Write data code DF i desig designa start address end address k CR na tion tion 2 2 1 1 4 4 2 1 or 2 bytes worth of data Communications Specifies the method for communicating with a Tag designation Refer to Communications Designations for details
10. 30 25 20 15 10 5 0 5 10 15 20 25 30 Distance in x axis direction mm Electromagnetic Inductive RFID System User s Manual SECTION 6 Appendices E Operation Time Reference Operation time includes the TAT Turn Around Time and communications time Command Communications Response time TAT 4 gt The TAT is the total processing time required to operate the CF Reader Writer from the viewpoint of the Handy Terminal The communications time is the time required for communications between the CF Reader Writer and a Tag and does not include communications with the host device Communications Time The communications time is the time required for communications between CF Reader Writers and a Tag The time depends on the amount of data to be read or written Refer to the following charts for the communications time e Read 240 220 E 200 E 180 2 160 E 140 120 E 100 S 80 o 60 O 8 16 24 32 40 48 56 64 72 80 88 96 104112120128 No of processed data bytes e Write with Verification 240 220 200 180 160 140 120 100 80 60 Communications time ms O 8 16 24 32 40 48 56 64 72 80 88 96 104112120128 No of processed data bytes Electromagnetic Inductive RFID System User s Manual suoisuauiigq pue
11. Abort status Indicates a communication with a Tag was aborted after it was started using the aborting command AA Data Provides the data read according to the command Terminator Indicates the end of a command using the two characters 2A and the carriage return code 0D Electromagnetic Inductive RFID System User s Manual ewo esuodseg pueuiuo EAN etree 37 ewo osuodsoy puewwoy BJ SECTION 4 Commands Data Type Designation The data type to be used when transmitting read or write data between the CF Reader Writer and the Handy Terminal can be specified in a command Either ASCII or hexadecimal can be used E ASCII JIS8 Unit Code Designation A One byte of data in a Tag is transmitted directly as ASCII or JIS8 unit code Each transmitted character is equivalent to 1 byte of data in the Tag Character data can be directly read or written but do not use the carriage return CR control code in send data If the CR control code is used in write data a com mand error will occur e Data Write Example If V670 is specified as the write data for 4 bytes of memory begin ning with the address 10h the data is written to the Tag memory as shown in the diagram W T S A A 1 0 0 1 0 0 4 V 6 7 0 x CR I I l I LI LJ Command Communica ASCII Antenna Start address No of bytes Write data tions desig desig designa i nation tion e Data Rea
12. CR I I 2 2 1 1 Specified number of bytes 2 Read data User ID data read from a Tag 00000000 to 3FFFFFFF The leftmost 2 bits are system bits and are always 0 Example Reading Tag User ID Single Auto User ID 12345678 Send data IDSAH1 CR Receive data ID000012345678x CR SPUBLWILUOD suormneoiunuluilo EAN I RES v All Tags store their own unique ID The ID Read command can be used for very fast communications if all that is A required is to detect whether or not there is a Tag in the communications area CHECK Electromagnetic Inductive RFID System User s Manual 51 SECTION 4 Commands Communications Subcommand The communications subcommand is used in combination with communications commands No communications processing is performed with Tags when the communications subcommand is used alone Command Processing Abort AA Aborts processing of a command being executed and returns to the command standby status Com mand Processing Abort can be executed during the processing of any command Command Proc Antenna code AA ess desig desig nation CR nation 2 1 1 2 Process designation Always 0 Antenna designation Always 1 Response Command End code Retry Status code AA flag flag CR 2 2 1 1 2 When command processing has been aborted after a Tag is detected the status flag will be 2 Example Aborting Command Process
13. THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM PERFORMANCE DATA Performance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty It may represent the result of OMRONSs test conditions and the users must correlate it to actual application requirements Actual performance is subject to the OMRON Warranty and Limitations of Liability CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons It is our practice to change model numbers when published ratings or features are changed or when significant construction changes are made However some specifications of the product may be changed without any notice When in doubt special model numbers may be assigned to fix or establish key specifications for your application on your request Please consult with your OMRON representative at any time to confirm actual specifications of purchased products DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes even when tolerances are shown ERRORS AND OMISSIONS The information in this document has been carefully checked and i
14. Tag If communications are possible there is an error in the Tag Communications Command format 14 error with the Handy zi p 35 Commands Terminal Handy Terminal communications specifications il A p 68 Interface Specifications a a CHECK 417 Ifthe problem cannot be solved after performing the above checks the CF Reader Writer may be faulty Electromagnetic Inductive RFID System User s Manual SECTION 5 Troubleshooting Errors and Countermeasures Problems with the CF Reader Writer are normally caused by one of the following four problems e Handy Terminal is faulty e CF Reader Writer is faulty e Tag is faulty e Other Repairs are required if a device is faulty Troubleshooting When an error occurs study the situation fully determine if the error will recur and its relation to other devices and then check the error according to the following flowchart soJ1nseeulij9 uno pue s10113 ANTEE E Electromagnetic Inductive RFID System User s Manual sojnse9u191uno3 pue sJoJJ 3 Ege ES SECTION 5 Troubleshooting E Operation Check Flowchart C Is the Handy Terminal power turned ON Contact the sales representative for the Handy Terminal manufacturer Use a recommended Handy Terminal UA p12 S a recommended Handy Terminal being used Is the CF Reader Writer connected prop erly to the CF card slot in the Handy Writer Connect the CF Reader Wr
15. check block which is specified using the start 00 address and the number of bytes all but the last two bytes 9 are the calculation area The last two bytes of the block are the check code area Area start address When a Check Code Write command is sent the CRC code for the data in the calculation area is calculated and a oriri e written to the check code area When a Data Verify command is sent the CRC code for the data in the calculation area is calculated and compared to the data in GRC etos code area 2 bytes the check code area When the data matches O is EC PIOS D returned as the response status flag to indicate that the data is normal If the data does not match 1 is returned as a warning uonounJ 29u5 owanw BT Calculate and write the check code using the Memory Check command MD after writing data and verify the check code before reading data This enables detecting in advance data corruption in Tags that can occur while the Tags are not being accessed TET v Writing stage Data write v Check code calculation v Reading stage Check code verification v Data read vst Refer to Memory Check MD when using the Memory Check function A A p 48 CHECK Electromagnetic Inductive RFID System 32 User s Manual SECTION 3 Functions Write Protection The write pro
16. data SP0000x CR Electromagnetic Inductive RFID System User s Manual 53 SPUBWILWOD O1 UOD J19j041U0 BAN IES 54 SECTION 4 Commands Reset XZ Resets the CF Reader Writer Command code XZ No response is sent wu A response is not returned for the Reset XZ command The indicator will flash green when this command is received a Check the indicator after sending this command to confirm that it has been received lt CHECK Example Resetting the CF Reader Writer Send data XZx CR Receive data None Electromagnetic Inductive RFID System User s Manual SECTION 4 Commands Host Commands Test TS Returns the message sent by the Handy Terminal directly as the response The Test command is used to test communications between the CF Reader Writer and a Handy Terminal Command Command wren Message data code TS x CR 2 2 Message data Any character string for testing communications Response Command End code Retry Status Message data code TS flag flag x CR 2 2 1 1 2 Example Sending Message Data OMRON from the Handy Terminal Send data TSOMRONX CR Receive data TS00000MRON CR spuewu09 jsoy NIE Version Information VS Reads the CF Reader Writer model information software version and creation date and time Command code VS CR 2 2 Response Command End code Retry Status Model information software version creation date and time code VS fl
17. is a type of non volatile memory that can write data much faster than previous types of memory e such as EEPROM and flash ROM and it has a semipermanent writing life Furthermore the previous types of memory could no longer hold data if nothing had been written to the memory for a certain period approximately 10 years FeRAM on the other hand is far better for data storage because it can hold data as long as data is read or written within a specific period of time Electromagnetic Inductive RFID System User s Manual Part Names and Functions CF card section Indicator SECTION 1 Product Outline NY Antenna Type II Name Details Antenna The Antenna is brought close to the Tags in order to communicate with them CF card section The interface for connection with a Handy Terminal Conforms to the CF Card specification Compact Flash Type II Specification Revision 2 0 Indicator Status Description Lit time and number of flashes Green lit Command received from Handy Terminal 3s Communications with Tag ended normally 5s When the result is A low noise level for the Noise Mea 5s surement command NS When the result is 0 normal for the Error Noise Detec 5 s tion command EN When the result is A excellent for the Stability Evalua 5 s tion command SF Green flashing After completing initialization when power is turned ON 6 times During communications w
18. los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE Portuguese Omron declara que a RFID Sistema Antena V670 H11 S rie V670 H51 S rie V670 H51Q S rie e Controlador V670 CD1D S rie ser conforme com os tequisitos essenciais e outras disposi es da Directiva 1999 5 CE Romanian Prin prezenta Omron declar c acest V670 CF01 este conform cu cerintele principale ci cu celelalte prevederi relevanate ale Directivei 1999 5 EC Electromagnetic Inductive RFID System User s Manual AYIWAOJUOD plepuejs R Introduction Precautions for Safe Use For safety be sure to observe the following precautions 1 Do not operate this device in any flammable explosive or corrosive gas environment 2 Do not disassemble repair or modify this device 3 Use only the recommended Handy Terminals Proper operation many not be possible if any other Handy Terminal is used Z p12 4 Insert the CF Reader Writer into the CF card slot with the indicator on the CF Reader Writer facing upward 5 Be sure to attach the Protective Covers to the Handy Terminal Be sure to tighten the mounting screws securely The Protective Covers are not designed to withstand dropping 6 Do not apply excessive force to the surface of the antenna when communicating with an ID Tag 7 If the system gives out a foul smell or if the CF Reader Writer becomes abnormally hot emits smoke or exhibits a
19. memory has a user area and an ID code The memory capacity of the user area is 128 bytes One byte of data is written to one address The memory area is divided into pages of 4 bytes 0000h to 0003h 0004h to 0007h etc E Memory Map User area Page User address Write protection not used Write protection used 0000 0001 1 Specified address in protected area 0002 0003 0004 User area User area 007F f write protection is used addresses 0000h to 0003h are used for protection address information and cannot be used as part of the user area For details refer to Write Protection UA p 33 Write Protection W BID Codes This is a 4 byte area where a Tag identification number unique Tag number is written The ID code is written at shipment and cannot be changed The ID code can be read using the ID read command dey owanw EE Electromagnetic Inductive RFID System User s Manual uonoedsu pue sdueusjuley ETYeTISET 84 SECTION 6 Appendices Maintenance and Inspection To maintain the CF Reader Writer in optimum condition daily or periodic inspections are required The CF Reader Writer mainly consists of semiconductor components which have a long life The following malfunctions however may occur depending on the environment and operating conditions 1 Deterioration of elements due to overvoltage or overcurrent 2 Deterioration of elements due
20. questions or comments WARRANTY OMRON s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year or other period if specified from date of sale by OMRON OMRON MAKES NO WARRANTY OR REPRESENTATION EXPRESS OR IMPLIED REGARDING NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE OMRON DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS WHETHER SUCH CLAIM IS BASED ON CONTRACT WARRANTY NEGLIGENCE OR STRICT LIABILITY In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY REPAIR OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED STORED INSTALLED AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION ABUSE MISUSE OR INAPPROPRIATE MODIFICATION OR REPAIR SUITABILITY FOR USE THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF PERSONS AND SHOULD NOT BE RELIED UPON AS A SAFET
21. to long term stress caused by operation in locations with high ambient temperatures 3 Deterioration of insulation or imperfect connector contact due to humidity or dust 4 Imperfect connector contact or corrosion of elements due to corrosive gas Inspection item Fluctuation in power supply Inspection details Check at the power supply terminal block Criteria Within the specifications for power sup Required equip ment Tester Check that the protective cover is firmly mounted The cover must be secured by screws voltage that the criteria area satisfied ply voltage Check whether instantaneous power fail Within allowable voltage fluctuation Power supply ure occurs frequently and whether volt range analyzer age fluctuates considerably Ambient envi Temperature Check if within specifications Within the specifications Lowest tempera ronment Humidity ture thermometer Hygrometer Vibration and Check for vibration or shock from shock machines Dust Check for adherence or sedimentation of No dust or foreign matter dust or foreign matter Corrosive gas Check for discoloration or corrosion in metal parts Mounting state Check that the CF Reader Writer is com There is no looseness Phillips screw pletely inserted The CF must be Type II driver Electromagnetic Inductive RFID System User s Manual SECTION 6 Appendices Table of JIS8
22. was received aur Refer to Errors for corrective actions for the above errors a p 62 CHECK E Tag Communications Errors Tag errors are errors in communications between the CF Reader Writer and a Tag The indicator will flash red when a Tag missing tag error occurs and will light red when any other tag error occurs sojnse9u191uno3 pue s10113 Ege ES Error code Name Description 70 Communications error An error occurred during communications with a Tag and the communications could not be completed normally 71 Verification error The correct data could not be written to the Tag possible only when verification is enabled 72 No tag error There is no Tag in the CF Reader Writer communications area 7A Address designation The designated processing address is not suitable and the execution is impossible error 7D Write protection error Data was written to a write protected page 7E Lock error Write was specified to a locked area 7F Tag error Communications were attempted with a Tag for which communications are not enabled e g no password setting 1 Refer to Errors for corrective actions for the above errors UA p 62 CHECK Electromagnetic Inductive RFID System 66 User s Manual SECTION 6 Appendices Specifications and Dimensions 68 CF Reader Writer 68 Tags 70 Protective Covers 73 Communications Distance Specifications 75 Characteris
23. when characters are continually transmitted If the number of command characters is A the number of response characters is B the baud rate is 38 400 bps the data length is 8 bits the parity is even and there is 1stop bit the following formula can be used 11 x A B TAT communications time 38400 The above formula finds the time when processing is started command transmitted with the Tag inside the communications area of the CF Reader Writer The time depends on the communications mode and the Tag status Electromagnetic Inductive RFID System User s Manual SECTION 6 Appendices Characteristics Data Based on Operating Conditions Mutual Interference between Tags When using multiple Tags maintain the distances between Tags shown below to prevent malfunction due to mutual interference e V670 D13F03 E V670 D13F01 H 16 mm min n Using the above information as reference carry out preliminary tests or take other appropriate measures to ensure j proper installation z CHECK suonipuo Bunejedo uo peseg ejeg sonsuojoejeu EN Electromagnetic Inductive RFID System User s Manual SuOo Ipuoy Bunejedo uo paseg ejeg sousuojoe1euJ Byers SECTION 6 Appendices Influence of Metal behind Tags Reference Take into consideration the influence of metal behind Tags when installing them The communications range deteriorates if there is any metal material behind the Ta
24. 007F Range for protection area 0004h to 007Fh st Area 0000 to 0003 cannot be used as data area if the write protection function is used a z CHECK Electromagnetic Inductive RFID System User s Manual 33 SECTION 4 Commands 44 CF Reader Writer Operation Status 36 4 Command Response Format 37 Command Frames 37 m Response Frames 37 3 Data Type Designation 38 Ranges for Start Address and Number of Bytes 39 Command Response Flow 40 No Response 40 Single Response 40 Multiple Responses 40 Command List 41 44 Communications Designations 43 Communications Commands 44 44 Communications Subcommand 52 lt j Controller Control Commands 53 Host Commands 55 Appraisal Commands 56 44 End Code List 59 Electromagnetic Inductive RFID System User s Manual 3 snjeis uonegedo Je Mjepeoy 4D NOTRE SECTION 4 Commands CF Reader Writer Operation Status A command 1 sent from the connected Handy Terminal initiates communication between the CF Reader Writer and a Tag 2 The CF Reader Writer then returns the result as a response 3 to the Handy Terminal Handy Terminal Tag CF Reader Writer 2 lt gt Command Communications between the CF Reader Writer and the Tag 3 Response E CF Reader Writer Operation Status e Command Standby Status This is the status where the CF Reader Writer is not processing any commands but can accept any command e
25. 0h Electromagnetic Inductive RFID System User s Manual SPUBLWILUOD suomneoiunuluilo EAREN 45 SECTION 4 Commands Computation Write CW Performs a hexadecimal calculation using the data in Tag memory and the calculation data and writes the result to the Tag If an overflow occurs for addition or an underflow occurs for subtraction the data is not written to the Tag and 1 is returned for the status flag Command Communica Proc Antenna Calculation area No of bytes Calculation data code CW tions desig ess designa start address in calculation x CR nation desig tion area nation 2 2 1 1 4 2 Specified number of bytes 2 Communications Specifies the method for communicating with a Tag designation Refer to Communications Designations for details jl A p 43 Process designation Specifies the calculation method A Hexadecimal addition S Hexadecimal subtraction Antenna designation Always 1 Calculation area start Specifies the start address in the Tag memory area for calculating data in four hexadecimal digits address Specification range 0000h to 007Fh No of bytes in calculation Specifies the number of bytes of calculation data in the calculation area in two hexadecimal digits area Specification range 01h to 04h Calculation data Specifies in hexadecimal the number to be used in the calculation Response Command End code Retry Status Results data
26. 3F01 V670 D13F01H Recommended Handy Terminals Manufacturer Symbol Technology SHARP Model PDT8046 RZ N155S os PocketPC2002 Windows CE NET4 2 The Handy Terminal manufactured by Symbol Technology is recommended for use in the USA Canada Europe and China Contact your local Symbol Technology representative for further information http www symbol com index htm vt Use one of the recommended Handy Terminals listed in the above table The CF Reader Writer may not operate correctly if any E a other Handy Terminal is used For Handy Terminal operating procedures refer to the operating instructions provided by the man ufacturer CHECK Electromagnetic Inductive RFID System User s Manual Application Flowchart Preparation Communications preparatio Trial operation a c S E E e o Connect the CF Reader Writer UA p 16 Set the Handy Terminal communications conditions UA p 25 Test communications between the Handy Terminal and CF Reader Writer p 27 Test communications between Tags and the CF Reader Writer UA p 27 Check the ambient environment UA p 79 Actual communications using commands VA p 35 SECTION 1 Product Outline Electromagnetic Inductive RFID System User s Manual L NOILO3S ueuoMo J uoneoiddy 13 SECTION 2 Communications Preparations z NOILOAS Co
27. O T I Solid foreign material 1 mm or more in diameter e g wire cannot enter o 4 ru un o LJ O n o Dust in a volume that interferes with the normal operation of devices or reduces safety cannot r 5 enter 7 o 3 No dust can enter 6 B Protective Classification for 2nd symbol Water Penetration Class Protection level Test method overview tested with fresh water 0 No particular protection No particular protection No test against water penetration 1 Protection against drops of Not to be affected by water Drop water for 10 minutes using a water drop tester water drops from vertically above 2 Protection against drops of Not to be affected by water Drop water to an object set at an incline of 15 for 10 water drops from within 15 of a minutes 2 5 minutes in each direction using a water vertical line drop tester Electromagnetic Inductive RFID System 86 User s Manual SECTION 6 Appendices Class Protection level Test method overview tested with fresh water 3 Protection against water Not to be affected by water Spray water in an area within 60 to the right and left spray spray from within 60 of a from a vertical line for 10 minutes using the tester X vertical line shown in the following figure I 0 07 min per spray hole 4 Protection against water Not to be affected by water Spray wat
28. OMRON Electromagnetic Inductive RFID System V670 Series User s Manual C CF Reader Writer V670 CF01 ID Tag V670 D13F03 V670 D13F01 V670 D13F01H Cat No Z204 E1 02 Testam Standard Conformity Be sure to read Saa Product Outline SHeulewe Communications Preparations Sao o e Functions Sa 4 Commands Szaro Troubleshooting Appendices Specifications and Dimensions Characteristics Data Based on SECTION 6 Operating Conditions Memory Map Maintenance and Inspection Table of JIS8 Unit Code ASCII Degree of Protection Electromagnetic Inductive RFID System V670 CF01 CF Reader Writer V670 D13F03 ID Tag V670 D13F01 ID Tag V670 D13F01H ID Tag User s Manual 9 NOILOAS praese NOILO3S Hui L NOILO3S uononponu Introduction Introduction OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual Observe the following precautions when using a V670 series Electromagnetic Inductive RFID System e Read and understand this manual before attempting to use the product and use the product correctly e Keep this manual in a safe but accessible location so that it can be used as reference when required READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document before using the products Please consult your OMRON representative if you have any
29. System User s Manual SECTION 6 Appendices Protective Covers E Dimensions e V670 A75SY8046 for Symbol Technology Handy Terminals 60 4 53 4 Two 3 x 5 oblong holes SUS304CP T1 2 SUS304 4 dia inter nal diameter 2 4 dia 72 SUS304 dia inter nal diameter 2 4 dia 40 20 Two 2 2 dia 55 Accessories Mounting screws 4 40 2 screws Mounting screws 2 56 2 screws suoisuauuigq pue suoneoyioeds IETNS TRET Electromagnetic Inductive RFID System User s Manual SECTION 6 Appendices e V670 A75SH155S for SHARP Handy Terminals 38 8 Two 2 2 dia SUS304CP T1 2 N SUS304WPB 4 dia i 4 72 6 r gt ff Two 2 2 dia 64 4 hole pitch Accessories Mounting screws M2 4 screws suoisueuiig pue suoneoijioods ETNSTRET Electromagnetic Inductive RFID System User s Manual SECTION 6 Appendices Communications Distance Specifications The communications distance depends on the mounting conditions Carefully check the conditions listed here E Maximum Communications Distances Specification Values Tag model Communications distance V670 D13F03 0 to 8mm V670 D13F01 0 to 3 mm V670 D13F01H 0 to 3 mm B Measurement Cond
30. Tag and evaluates the received data p 58 1sr1 puewwoy ANTEE Electromagnetic Inductive RFID System 42 User s Manual SECTION 4 Commands Communications Designations The following two communications designations can be specified using communications commands Communica tions desig Name Description nation code SA Single auto After the Single Auto command has been received a communication is executed when a Tag is detected in the communications area and a response is returned Repeat auto The operation specified under SA is repeatedly executed The CF Reader Writer RA communicates only once with each Tag even if that Tag continues to be in the communications area Processing can be canceled by the Command Processing Abort command and the Parameter Setting command auto command abort time Electromagnetic Inductive RFID System User s Manual suoneuBiseg suoueaunuwuoj PAVIE 43 SECTION 4 Commands Communications Commands This section describes the commands used for communicating with Tags Read RD Reads data from the area specified by start address and number of bytes Command Command Communica Data Antenna Read area start No of read code RD tione desig kd designa address bytes CR l tion l l l 2 2 1 1 4 2 2 Communications Specifies the method for communicating with a Tag designation Refer to Communications Designations for details jl p 43 Data des
31. Unit Code ASCII b4 to b1 TC7 DLE U DC DC2 DCs DC4 TCs NAK TC SYN TC10 ETB CAN EM SUB ESC IS4 FS ISs GS IS2 RS IS1 US Undefined Undefined Undefined Undefined IIO nim O 0 ul z O AGN o a BR OJIN O O MN O a BI O N N lt X 8 lt C 3 ow D O o L UTO HS N HS AN er m V a o R nM O Z ZS r A gt oa M IIDSV epoo yun esir jo aqe 1 EASE Electromagnetic Inductive RFID System User s Manual 85 SECTION 6 Appendices Degree of Protection IP is classified by the test method described below Check sealing in a working environment and operating conditions in advance IP refers to the International Protection code B IEC International Electrotechnical Commission Standards IEC60529 1989 11 i ll B A Protective Classification for 1st symbol Solid Foreign Objects Class Protection level 0 No protection L 50 mm dia Solid foreign material 50 mm or more in diameter e g a hand cannot enter 1 eD je e m e 125 mm dia Solid foreign material 12 5 mm or more in diameter e g a finger cannot enter m 2 O el jo a o e z Solid foreign material 2 5mm or more in diameter e g wire cannot enter o l 2 5 mm 9 3 o T
32. Y COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES Please refer to separate catalogs for OMRON s safety rated products OMRON shall not be responsible for conformity with any standards codes or regulations that apply to the combination of products in the customer s application or use of the product At the customers request OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product machine system or other application or use The following are some examples of applications for which particular attention must be given This is not intended to be an exhaustive list of all possible uses of the products nor is it intended to imply that the uses listed may be suitable for the products Outdoor use uses involving potential chemical contamination or electrical interference or conditions or uses not described in this document Nuclear energy control systems combustion systems railroad systems aviation systems medical equipment amusement machines vehicles safety equipment and installations subject to separate industry or government regulations Systems machines and equipment that could present a risk to life or property Please know and observe all prohibitions of use applicable to the products NEVER USE
33. above procedure does not correct the problem the CF Reader Writer may be faulty e lt a CHECK E Nonfatal Errors When errors occur during communications between the CF Reader Writer and the Handy Terminal or between the CF Reader Writer and Tags the indicator lights or flashes red The indicator will turn OFF after lighting or flashing and the command will be received Check the information in the following table uonounJ sisoubeig Eee T 62 and take appropriate corrective actions before restarting operation Indicator Status Description Error code Lights red Error in communica Ambient noise interference 70 tions with Tag il A p 56 Appraisal Commands Tag write life expired replace Tag 71 Processing address specification 7A il z p 39 Ranges for Start Address and Number of Bytes Tag v write protection settings 7D il A p 49 Tag Function Designation TF Model or specifications of the Tags being used 7E 7F Settings e g lock setting of the Tags being used 7E 7F Tag operating environment Tags destroyed by unanticipated usage 71 7E 7F Try communicating with a different Tag If communications are possible there is an error in the Tag Flashes red Tag missing error Distance between CF Reader Writer and Tag 72 il B p 75 Communications Distance Specifications Tag operating environment Tags destroyed by unanticipated usage 72 Try communicating with a different
34. ag flag x CR 2 2 1 1 2 Example Reading the CF Reader Writer Software Version Send data VSx CR Receive data VS0000V670 CF01 00000000 1 00 2004 04 01 x CR Electromagnetic Inductive RFID System User s Manual 55 SECTION 4 Commands Appraisal Commands If errors are frequent during communications with Tags one of the causes may be ambient noise The appraisal commands are used to investigate whether or not noise is the cause of errors It can also be used to check noise generation at installation sites before installing V670 series Tags or Antennas and Controllers Even if read results are normal reception waveforms may exhibit interference These commands can be used to check for noise at the waveform level to provide more detailed information on the actual status of the waveforms Noise Measurement Command NS Investigates the noise level when commands are received Command code NS x CR 2 2 Response spuewwoy jesieiddy Be Noise evaluation result The noise level is evaluated as the maximum absolute value in the measured data A Low noise level 0 0 V to 2 0 V indicator will light green B High noise level 2 0 V to 3 3 V indicator will flash red Example Investigating Ambient Noise Level Send data NSx CR Receive data NS00000A CR Electromagnetic Inductive RFID System User s Manual SECTION 4 Commands Error Noise Detection Command EN The Error Noise Detection command d
35. arameter settings are not stored a Refer to Parameter Setting SP for information on using the Parameter Setting SP command N z 58 CHECK p Auto Command Abort Time When an Auto command is received the CF Reader Writer waits until a Tag is detected in the communications area and then starts communications If however a Tag is not detected within a set period processing is aborted and a No Tag error 72 is returned A command error will be returned if 00 is set as the Abort auto command time Trans mission CF Reader Writer to Tag Tag to CF Reader Writer CF Response Reader Writer to Host Error 72 Auto command abort time External input 01 to60 s The default setting is 10 s Write Verification Write verification checks that any data written to Tags is correct A verification error 71 will be returned if the data is not written correctly 0 write verification disabled 1 write verification enabled The default setting is 1 write verification enabled Electromagnetic Inductive RFID System User s Manual s1ojoue1eg Buneiodo Buss BYE 31 SECTION 3 Functions Memory Check Function A check code can be added to the data in a Tag to detect errors from memory write life or unexpected causes The polynomial X16 X12 X5 1 is used to generate a CRC code as the check code Use the Memory Check command MD to write and verify commands Address In the
36. ation Flowchart 13 SECTION 2 Communications Preparations 15 Connection 16 Tags 17 Protective Covers 21 Setting Handy Terminal Communications Conditions 25 Communications Test 26 SECTION 3 Functions 29 Communications Designation Function 30 Setting Operating Parameters 31 Memory Check Function 32 Write Protection 33 Electromagnetic Inductive RFID System User s Manual 7 Introduction SECTION 4 Commands CF Reader Writer Operation Status Command Response Format Command Response Flow Command List Communications Designations Communications Commands Communications Subcommand Controller Control Commands Host Commands Appraisal Commands End Code List SECTION 5 Troubleshooting Diagnosis Function Errors and Countermeasures SECTION 6 Appendices Specifications and Dimensions Characteristics Data Based on Operating Conditions Memory Map Maintenance and Inspection Table of JIS8 Unit Code ASCII Degree of Protection Manual Revision History Electromagnetic Inductive RFID System User s Manual 35 36 37 40 41 43 44 52 53 55 56 59 61 62 63 67 68 79 83 84 85 86 90 SECTION 1 Product Outline L NOILOAS 44 Features 10 44 Part Names and Functions 11 4 System Configuration 12 Application Flowchart 13 Electromagnetic Inductive RFID System User s Manual o m o d e z m soinjeo4 10 SECTION 1 Product Outline Features The V670 CF01 CF Reader Wri
37. ccur no matter how not enabled e g no password setting many times communications are attempted replace the Tag ave CHECK Refer to Part Names and Functions for details on the indicator IA p 11 Electromagnetic Inductive RFID System User s Manual ISI pos pu3 TRE 59 SECTION 5 Troubleshooting 4 Diagnosis Function Errors 44 Errors and Countermeasures Troubleshooting Error Tables 62 62 63 63 66 Electromagnetic Inductive RFID System User s Manual S NOILOAS 61 SECTION 5 Troubleshooting Diagnosis Function When errors occur with the CF Reader Writer the type of error can be determined through the indicator i e by whether the indicator lights red or flashes red Errors The errors detected by the diagnostic function can be classified into two types of errors One terminates operation fatal errors and the other does not terminate any operation nonfatal errors E Fatal Errors When a CPU error has occurred in the CF Reader Writer CPU operation is terminated and the indicator lights red The indicator will remain lit red until the power supply is turned OFF Check the information in the following table and take appropriate corrective actions before restarting operation Status Error code CPU error Indicator Lights red Description Turn OFF the power supply and then turn it back ON to return to initial status 417 Ifthe
38. d Example Tag memory f f Add i If 4 bytes of memory is read starting with address 10h the read don 5 6 y data will be V670 for the data shown in the diagram 5 j 4 m 12h 8 7 7 R Dj o o 0 0 v 6 7 0 CR 13h 3 i 0 o E ILI Command End code Pad rw Read data E Hexadecimal JIS8 Unit Code Designation H One byte of Tag data is converted to two hexadecimal characters 00 to FF and transmitted Each transmitted character is equivalent to 1 byte of data in the Tag Always set write data in the 2 character units 00 to FF i e as an even number of characters A command error will occur if an odd number of characters is accidentally set e Data Write Example If 56363730 is specified as the write data for 4 bytes of memory beginning with the address 10h the data is written to the Tag memory as shown in the diagram Command Commune HEX Antenna Start address No of bytes Write data ions desig desig designa nation nation tion e Data Read Example Tag memory If you read 4 bytes of memory starting with address 10h the read data Ro Bo u will be 56363730 for the data shown in the diagram l 3 i 6 ve 12h 8 y R D 0 0 0 0 5 6 3 6 3 7 3 0 CR PLT LI 13h x 9 Command End code Rory Status Read data g flag Electromagnetic Inductive RFID System User s Manual SECTION 4 Commands Ranges for Start Address and Number of Bytes The following table
39. d when communi cations have been completed Host to CF Reader Writer Response E i CF Reader Writer to Host Processing completed p tions Between CF Reader Writer and Tag Tag movement E RA Designation When the Repeat Auto command RA is specified the CF Reader Writer waits for the next Tag each time communications are completed Once communications have been performed with a Tag there are no more communications with that Tag until the Tag has moved outside the communications area This processing is repeated until it is ended when the Command Processing Abort command AA is received Host to CF Reader Writer Response Response Response Processing completed CF Reader Writer to Host Waiting fora Tag Waiting for a new Tag Waiting for a new Tag Communi Communi cations B ations C gt Between CF Reader Writer and Tag Tag movement Electromagnetic Inductive RFID System User s Manual SECTION 3 Functions Setting Operating Parameters The operating parameters outlined below can be set to optimize CF Reader Writer performance and reliability and to optimize the system itself If changing the operating parameters always do so with the power turned ON Normally there are no problems in using the default settings e Auto command abort time e Write verification Uo The CF Reader Writer is initialized when the power is turned OFF and the operating p
40. ecking operation using actual commands Trial operation completed Electromagnetic Inductive RFID System User s Manual Trial operation of system i p 27 Testing Communications between Tags and CF Reader Writer SECTION 2 Communications Preparations Testing Communications between Handy Terminal and CF Reader Writer A Test command is used to test communications between the CF Reader Writer and Handy Terminal This enables checking the CF card slot connection and communications processing before performing trial operation of the system wn m o 1 Send a Test command from the Handy Terminal 9 N vw Referto Test TS for information on using the Test command o Q 9 W p 55 Test TS CHECK A P 79 3 2 The CF Reader Writer will return the received data if the communications network is operating nor S mally S 7 vstr Refer to Errors and Countermeasures if there is no response from the CF Reader Writer 9 UA 63 Errors and Countermeasures cuecx DS P Testing Communications between Tags and CF Reader Writer Actual commands are used to test communications between Tags and the CF Reader Writer 1 Enter the Read command from the Handy Terminal CN Refer to Commands for information on how to use the command m A p 35 Commands 2 Bring the antenna on the CF Reader Writer close to the Tag CHECK Electromagnetic Inductive RFID System User s Manual 27 jse suoneoiunuiuo EAXNSTISETS
41. em Specifications Communications func Single repeat and write protection functions tion Memory check function noise measurement function communications stability evaluation function Bi Interface Specifications suoisueuiig pue suoneojoods ETYTETISET Item Description Connector CF Card connector Type Il Communications method 1 1 Synchronization method Start stop synchronization Baud rate 38 400 bps Communications control 1 1 protocol Communications control CR control Character control not supported method Character format Start bits Data bits Parity Stop bits 1 8 Even 1 E Electrical Interface Specifications The electrical specifications for the interface conform to the CF Card specification Compact Flash Specification Revision 2 0 Electromagnetic Inductive RFID System 68 User s Manual B Dimensions Unit mm 34 1 Two 2 5 dia i l A eo S s la V ee 3 90 1 43 8 Electromagnetic Inductive RFID System User s Manual suoisuauiigq pue suoneoyioods IETNSITRET 69 SECTION 6 Appendices Tags E Specifications Item Description Model V670 D13F01 V670 D13F01H V670 D13F03 Memory capacity 128 bytes Memory type FeRAM non vo
42. ens Mounting Method Observe the following precautions when mounting Tags e Do not chip or make holes in Tags e Do not apply excessive force to Tags e Do not mount Tags side by side or close to metallic objects Tags may warp if used in an environment subject to repeated high and low temperatures but this will shel FaNeibe not affect Tag functions E V370 D13F01 H e Mounting Direction Mount section 7 Marking surface Z e Mounting Example Use two M3 screws to mount a Tag id Mounting Hole Dimensions Two M3 holes 20 5 0 1 o e Unit mm Electromagnetic Inductive RFID System User s Manual 17 shel BABE Tags must be mounted on flat surfaces Do not mount Tags on curved surfaces The Tag may be damaged due to tightening stress if it is mounted on a curved surface I_I x tY Tighten the M3 screws to a torque of 5 N m or less CHECK Electromagnetic Inductive RFID System User s Manual SECTION 2 Communications Preparations E V670 D13F03 e Mounting Direction Mount the V670 D13F03 Tag so that the front is parallel to the CF Reader Writer Mounting section Marking surface shel Ae e Mounting Example Use two M3 screws to mount a Tag Mounting Hole Dimensions Two M3 holes C O ae N e M 32 gt Unit mm Electromagnetic Inductive RFID System User s Manual 1 shel BABE Tags must be mounted on flat surfaces Do not mou
43. er for 10 minutes from all directions using the splash splash from any direction tester shown in the following figure 0 07 min per spray hole 5 Protection against water jet Not to be affected by direct Spray water from all directions for 1 minute per surface flow water jet flow from any area 1 m2 for a total of 3 minutes or more using the i direction tester shown in the following figure mc 2 5 to 3 m 12 5 min 6 Protection against extreme Not to be affected by extreme Spray water from all directions for 1 minute per surface water jet flow direct water jet flow from any area 1 m for a total of 3 minutes or more using the direction tester shown in the following figure 25to3m 100 min 7 Protection against water No water penetration even if Immerse the object to a depth of 1 m when the height soaking the object is immersed in of the device is less than 850 mm for 30 minutes water of a specified pressure for a specified time 8 Protection against water Can be used when always Agreement to be reached between the manufacturer immersion immersed in water and the device user B JEM Japan Electrical Manufacturers Association Standard JEM1030 1991 IP A B A Complies with 1st and 2nd symbols of IEC60529 B Protective Classification for Oil Penetration Note There are four other classes h c d and e Class Protection level f Oil retaining type No adverse affect fro
44. etects noise above a specified level When deciding where to mount Tags and Antennas use this command to investigate where the noise level is high Command Specifying Data 1 and Data 2 Omitting Data 1 Command paia Data Command Data code EN code EN 2 x CR 2 4 2 Omitting Data 2 Omitting Data 1 and Data 2 Command Data Command code EN 1 x CR code EN CR 2 2 2 2 2 Data 1 Specifies the error noise level in two decimal digits This setting may be omitted Error noise level Specification range 00 to 33 x 0 1 V Default 2 0 V When 00 is specified 100 Data 2 Specifies the error noise measurement time in four decimal digits This setting may be omitted Measurement time Specification range 0000 to 0100 s Default 0060 s When 0000 is specified Noise level when command is received is returned in the response When both data 1 and data 2 are omitted noise detection is performed using the previously specified values If they are omitted the first time this command is set after turning ON the power supply the default settings will be used for noise detection Response Command End code Retry Status Judge Maximum code EN flag flag ment noise level x CR result I I 2 2 1 1 1 2 2 Judgment result The noise level is evaluated as the maximum absolute value in the measured data 0 Normal indicator will light green 4 Error indicator will flash red Maximum no
45. g The following graphs show the deterioration in the communications distances depending on the distance between the Tag and the metal behind the Tag same size as the Antenna E V670 D13F01H e Metal Aluminum 100 90 80 70 60 50 40 30 20 10 Percent of communications distance The communications distance without metal is 100 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Distance between Tag and metal mm e Metal Iron 100 8 90 S 80 O 70 o 60 S 50 S 40 E 5 30 5 20 E 10 O A The communications distance without metal is 100 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Distance between Tag and metal mm CF Reader Writer Tag Communica tions dis tance Distance between Tag and metal behind Metal gt Electromagnetic Inductive RFID System User s Manual SECTION 6 Appendices E V670 D13F03 e Metal Aluminum lt 100 o 90 E S 80 5 70 2 60 The communications distance s without metal is 100 50 5 40 E 30 8 20 10 8 E O 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Distance between Tag and metal mm e Metal Iron 100 9 90 E 8 80 ka o 70 2 60
46. ignation Specifies the data format when sending the read data response A ASCII H Hexadecimal Antenna designation Always 1 Read area start address Specifies the start address in the Tag memory area for reading data in four hexadecimal digits Specification range 0000h to 007Fh No of read bytes Specifies the number of bytes of data to be read from the Tag in two hexadecimal digits The maximum number of characters that can be read at one time is 256 Specification range 01h to 80h Response Command End code RD 0 spueululio suoneoiunuluo KA TeTEeE ES code Retry Status Read data o flag flag 2 2 1 1 Specified number of bytes 2 Read data Data read from the Tag The number of characters is the number of read bytes in ASCII and the number of read bytes times 2 in hexadecimal Example Reading 8 Bytes of Data Starting from Address 0000h Single Auto Hexadecimal Send data RDSAH1000008x CR Receive data RD00001234567812345678 CR att Specify the total number of read bytes so that the sum of the read area start address and the number of bytes does not a exceed the Tag memory capacity 128 bytes oc Example The number of bytes can be specified between 01h and 70h for a start address of 0010h a Electromagnetic Inductive RFID System 44 User s Manual SECTION 4 Commands Write WT Writes the specified number of bytes of data starting from the specified sta
47. ing during Execution Send data AA01x CR Receive data AA0000x CR pueuiuiooqns suoneoiunuiuoo MJI Electromagnetic Inductive RFID System User s Manual SECTION 4 Commands Controller Control Commands Parameter Setting SP This command sets communications conditions by setting the parameters in the CF Reader Writer Command Command Process Parameter data code SP code only when x CR Upper Lower changing 2 2 2 Process code upper digit Specifies the process to be performed for the parameter 0 Change 1 Read 9 Initialize default setting Process code lower digit Specifies the parameter 4 Auto command abort time C Write verification Parameter data Parameter Setting range only when changing the Set two decimal digits 01 to 60 unit 1 s A command error will occur if 00 is set parameter Default 10 s C 0 OFF 1 ON Default 1 Write verification enabled The parameter number for the parameter data is the number specified in the lower digit of the process code Set the parameter data within the setting range given for the parameter number specified in the lower digit of the process code Sspueululo 041u0O J19j 043ju0 BAN eI RES Command End code Retry Status Parameter data code SP flag flag only when x CR reading 2 2 1 1 2 Example Setting Character Interval Monitoring Time to 500 ms Send data SP010500x CR Receive
48. ise level Gives the maximum noise level V detected during the measurement period in two decimal digits Unit 0 1 V Example Detecting Noise at 3 3 V or Greater during a Period of 5 s Send data EN330005x CR Receive data EN0000020x CR st The Error Noise Detection command can be canceled using the Command Processing Abort command AA because no response is given for a set period of time a MA pse Electromagnetic Inductive RFID System User s Manual spueuiuio jesieiddy EAN lke 57 SECTION 4 Commands Stability Evaluation Command SF The Stability Evaluation command evaluates the stability of received data Data is read from the Tag the received data is evaluated and the evaluation results are returned in the response and through the indicator Forty bytes of data is read starting from address 0000h Evaluation Criteria Response Meaning Evaluation criteria Indicator A Excellent Min 80 within distribution range Lit green B Good Min 60 within distribution range Flashing green C No good Less than 60 within distribution range Flashing red Command Command code SF x CR I 2 2 Response Command End code Retry Status Judge code SF flag flag ment x CR result 2 2 1 1 T 2 Example Investigating Communications Stability Send data SF CR Receive data SF0000Ax CR spuewwoy jesieiddy Be Electromagnetic Inductive RFID System User s Manual
49. iter so that the indicator is on the top N zi p 16 Is the CF Reader Writer indicator flashing green after the Handy Terminal power is turned ON Reset the Handy Terminal and turn ON the power again If the indicator does not flash after several attempts the Handy Termi nal CF port may be damaged Contact the sales representative for the Handy Terminal manufacturer Use the Handy Terminal program to open the COM port allocated to the CF port Is the indicator on the CF Reader Write flashing green when the COM por is opened Reset the Handy Terminal and execute the program again If the indicator does not flash after several attempts the CF port designation in the Handy Terminal may be incorrect or the Handy Terminal CF port may be damaged Contact the sales representa tive for the Handy Terminal manufacturer Send a test command TS from the Handy Terminal Check the communications format The default settings for the CF Reader Writer are as follows 38 400 bps baud rate 8 data bits even parity 1 stop bit ILA p 68 Is the response normal 1 Electromagnetic Inductive RFID System User s Manual SECTION 5 Troubleshooting 1 YES Send Read command RD from the Handy Terminal indicator on the CF Reader Writer flashing green The command format is incorrect Check the format of the Read command UA p 44 v Bri
50. ith a Tag Until communications end When the result is B good for the Stability Evaluation 8 times command SF Red lit When an error occurs in communications with a Tag 5s When a CPU error occurs Until power is turned OFF Red flashing When an error occurs because there is no Tag 10 times When an error occurs in communications with the Handy 5 times Terminal When the result is B high noise level for the Noise 15 times Measurement command NS When the result is 1 error for the Error Noise Detection 15 times command EN When the result is C No good for the Stability Evalua 15 times tion command SF When a CPU error occurs the indicator will remain lit until the power supply is turned OFF UA p 62 Diagnosis Function Electromagnetic Inductive RFID System User s Manual L NOILOAS suoloun 4 pue SOULN Med 11 o m o d e z m uoneanBijuo uiejs S 12 SECTION 1 Product Outline System Configuration The CF Reader Writer is inserted into a Handy Terminal CF card slot Type II and it controls communications with Tags using serial communications from the Handy Terminal Recommended Handy Terminals e Manufactured Manufactured by Symbol by Sharp Technology RZ N155S PDT8046 CF card slot Protective Cover e V670 A75SH155S For Sharp model e V670 A75SY8046 For Symbol Technology model 1 e SQ V670 D13F03 V670 D1
51. itions e V670 D13F03 CF Reader Writer Communica tions distance 7 Non metal e V670 D13F01 V670 D13F01H Tag D CF Reader Writer 7 A ae 7 Non metal suoisuauiig pue suoneoyioeds EMTEC Electromagnetic Inductive RFID System User s Manual 75 suoisueuiig pue suoneoijioods EMTEC 76 SECTION 6 Appendices E Communications Area Reference UM The communications area varies depending on how the Tag is installed The communications areas shown in the following dia i grams are based on OMRON tests and are not intended to imply any guarantee of the performance of the V670 series Electro magnetic Inductive RFID System CHECK e V670 D13F03 30 E E Y Nonmetal SS c 25 8 20 5 a 15 gt E o 10 c S 2 5 Cc l l l l i l i l J 25 20 15 10 5 0 5 10 15 20 25 30 Co o Distance in x axis direction mm e V670 D13F01 V670 D13F01H Tag Attached Perpendicular in Relation to Passing Direction X Direction Example E 30 E c Nonmetal SS 25 o o 5 20 L 15 E a 10 c S o a 5 l i i l i l l i i l i 30 25 20 15 10 5 0 5 10 15 20 25 30 Distance in x axis direction mm Tag Attached Horizontally in Relation to Passing Direction X Direction Example 30 E E Nonmetal 25 c o 9 20 5 W ux 15 n gt lt 10 c S 5 2 Q l l i l l l i I l i l
52. latile ferroelectric memory Memory life No of times accessed See note 1 billion Data holding time 10 years after access using write or read commands Ambient operating 40 to 70 C temperature Ambient storage 40 to 70 C temperature Ambient ti 00 35 to 95 35 to 85 humidity Enclosure rating IP67 IEC60529 standard Vibration resistance 10 to 2 000 Hz double amplitude 1 5 mm acceleration 150 m s Performed 10 sweeps for 15 minutes in upward downward left right forward and backward directions Shock resistance 500 m s 3 times each in upwards downwards left right forwards and backwards directions i e 18 times in total Material PPS epoxy resin filling material ABS epoxy resin filling Mass Approx 1 g Approx 1 g Approx 6 g comm nicaions 0 to 3 mm 0 to 3 mm 0 to 8 mm distance The number of times accessed refers to the total number of read and write communications B Dimensions e V670 D13F03 suoisueuiig pue suoneouyioeds TNSTRETS 16 0 2 8 Case material ABS resin 13 2 gt Filling material Epoxy resin Unit mm Electromagnetic Inductive RFID System 70 User s Manual SECTION 6 Appendices e V600 D13F01 Two RO 8 Four R0 5 Case material PPS resin Two R0 2 Two R0 8 Filling material Epoxy resin Reference Unit mm plane e V600 D13F01H Case material PPS resin Filling material Epoxy resin
53. ll of its components are in compliance with essential requirements and other relevant provisions of the Radio and Telecommunications Terminal Equipment Directive 1995 5 EC and satisfy tests for the appropriate requirements of the following relevant standards Radio EN 300 330 2V1 1 1 06 2001 EN 300 330 1V1 3 1 06 2001 EMC EN 301 489 3V1 4 1 08 2002 EN 301 489 1V1 4 1 08 2002 Safety EN 61010 1 2001 2nd Edition Ce English Hereby Omron declares that the RFID System Antenna V670 H11 Series V670 H51 Series V670 H51Q Series and Controller V670 CD1D Series are in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Finnish Omron vakuuttaa t ten ett RFID S nn s Antenni V670 H11 Series V670 H51 Series V670 H51Q Series jar Kontrollida V670 CDID Series tyyp pinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen Dutch Hierbij verklaart Omron dat het toestel de RFID Systeem Antenne V670 H11 Serie V670 H51 Serie V670 H51Q Serie en Controleur V670 CDID Serie in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijh 1999 5 EG French Par la pr sente Omron d clare que la RFID Syst me Antenne V670 H11 S rie V670 H51 S rie V670 H51Q S rie et Contr ler V670 CD1D S rie sont conforme aux exigences essentielles et aux autres dispositions pertinentes de la direc
54. m oil drops or oil spray from any direction g Oil resistant type Oil drops and oil spray from any direction do not enter Electromagnetic Inductive RFID System User s Manual uonoojoJd jo 991Bag IEENe TSELS 87 SECTION 6 Appendices E NEMA National Electrical Manufacturers Association Table for conversion from NEMA enclosure classifications to IEC60529 Conversion from IEC60529 to NEMA enclosure classifications is not available NEMA250 IEC60529 1 IP10 2 IP11 3 IP54 3R IP14 3S IP54 4 4X IP56 5 IP52 6 6P IP67 12 12K IP52 13 IP54 uonoojoJd jo 90160q ETR Electromagnetic Inductive RFID System User s Manual Manual Revision History A manual revision code is added to the end of the catalog number shown at the bottom of the front and back covers Catalog number Z204 E1 02 Revision code Date of Revision code ps Reason for revision revised page revision 01 August 2004 Original production 02 March 2005 Added table with standards compliance information for different languages Electromagnetic Inductive RFID System 90 User s Manual
55. ng the CF Reader Writer closer to the Tag Are communications with Tags OK Follow Check Table 1 v C Normal end e Check Table 1 Check point Corrective action Distance to CF Reader Bring the CF Reader Writer closer to the Tag so that it is within the communications range Writer sojnse9u19juno9j pue s1013 eget he Ey Tag write protection Release the Tag write protection settings Ambient metal Remove metal objects from near the Tag or change the mounting location of the Tag Noise Measure the noise level and take appropriate noise countermeasures Tags Communicate with the Tag with a different device to see if the Tag is functioning properly Electromagnetic Inductive RFID System User s Manual 65 SECTION 5 Troubleshooting Error Tables E Host Communications Errors Host communications errors are errors in communications between the CF Reader Writer and the Handy Terminal The indicator will flash red when a host communications error occurs Error code Name Description 10 Parity error A parity error has occurred in characters in the command 11 Framing error A framing error has occurred in characters in the command 12 Overrun error An overrun error has occurred in characters in the command Format error The command format is incorrect 14 The character interval exceeded the set time 18 Frame length error A command string longer than 300 characters
56. nnection 16 Tags 17 Protective Covers 21 4 Setting Handy Terminal Communications Conditions 25 44 Communications Test 26 Electromagnetic Inductive RFID System User s Manual 15 uonooeuuo KA eI EL 16 SECTION 2 Communications Preparations Connection 1 Turn OFF the power supply to the Handy Terminal V Always turn OFF the power supply to the Handy Terminal before connecting or disconnecting the CF Reader Writer For A Handy Terminal operating procedures refer to the operating instructions provided by the manufacturer z CHECK 2 Attach the Protective Cover to the end of the Handy Terminal RS Refer to Protective Covers for the attachment method for the Protective Cover Ca il 2 p 21 Protective Covers lt CHECK 3 Insert the CF Reader Writer into the Handy Terminal CF card slot CHECK 4 After the CF Reader Writer has been inserted turn ON the power supply to the Handy Terminal The indicator on the CF Reader Writer will flash after the Handy Terminal power has been turned ON Electromagnetic Inductive RFID System User s Manual SECTION 2 Communications Preparations Tags Installation Environment Do not use Tags in the following locations e Locations with corrosive gases flammable gases or dust e Locations with an ambient temperature not between 10 and 70 C and locations subject to sudden temperature fluctuations that may cause condensation e Inside microwave ov
57. nt Tags on curved surfaces The Tag may be damaged due to tightening stress if it is mounted on a curved surface Ix V Tighten the M3 screws to a torque of 0 6 N m or less B CHECK Electromagnetic Inductive RFID System User s Manual SECTION 2 Communications Preparations Protective Covers Mounting Method Protective Covers are mounted with screws E V670 A75SY8046 for Handy Terminals from Symbol Technology 1 Loosen the screws on the cover at the end of the Handy Terminal and remove the cover SJ9A02 9A2910Jd FANeIbES 2 Remove the screws from the hand strap bar and remove the bar Hand strap bar Electromagnetic Inductive RFID System User s Manual 21 SIBAOD 9A1 39101g RANe IES SECTION 2 Communications Preparations 3 Insert the pin as shown in the following diagram to attach the hand strap to the Protective Cover 4 Secure the Protective Cover to the Handy Terminal with two 4 40 screws and two 2 56 screws Mounting screws 4 40 Mounting screws 2 56 Tighten mounting screws 4 40 to a torque of 0 3 N m or less and mounting screws 2 56 to a torque of 0 15 N m or e less CHECK Electromagnetic Inductive RFID System User s Manual SECTION 2 Communications Preparations E V670 A75SH155S for Handy Terminals from Sharp 1 Loosen the mounting screws on the cover at the end of the Handy Terminal and remove the cover SJ9A02 9A2910Jd KANeOIBEE
58. ny other abnormal condition immediately stop using the system turn OFF the power and contact your OMRON repre sentative 8 Dispose of this product as industrial waste AYIWAOJUOD paepuejs Xie Electromagnetic Inductive RFID System 4 User s Manual Introduction Precautions for Correct Use Please observe the following precautions to prevent failure to operate malfunctions or undesirable effects on product per formance 1 Installation Environment Do not install the product in the following locations Where it is exposed to direct sunlight Where it is exposed to corrosive gases dust metal chips or salt Where the operating temperature exceeds the range given in the specifications Where there are sudden changes in temperature including locations subject to condensation Where the humidity exceeds the range given in the specifications Where vibration or shock exceeding the values given in the specifications is imposed directly on the product Where the product is subject to splashing water oil or chemicals ID Tag Installation This device uses the frequency band 13 56 MHz to communicate with Tags This frequency band is also used as the ISM band one of frequencies assigned to medical or industrial heaters These heaters may affect communications with a Tag or may damage the Tag if the heater is located near this device Do not install ID Tags near devices that use the frequency band 13 56 MHz
59. ocation When setting write protection for Tag memory addresses 0005h to 0010h single auto hexadecimal Setting Protection Area Information Send data WTSAH100000405100510 CR Receive data WTOOOO0 CR Setting Write Protection Send data TFSAP1x CR Receive data TF0000x CR xt When setting write protection for only one location set the same data to addresses 0002h and 0003h and to addresses a 0000h and 0001h lt lt CHECK e Write Protection Specified for Two Locations When setting write protection for Tag memory addresses 0005h to 0010h and addresses 0070h to 0075h single auto hexadecimal Setting Protection Area Information Send data WTSAH100000405107075 CR Receive data WT0000x CR Setting Write Protection Send data TFSAP1x CR Receive data TF0000x CR V Refer to Write Protection for details on write protection iS lt je CHECK UA p 33 Electromagnetic Inductive RFID System User s Manual SECTION 4 Commands ID Read ID Reads the Tag s user ID Command Communica Data Antenna code ID tions desig desig designa x CR nation na tion tion 2 2 1 1 2 Communications Specifies the method for communicating with a Tag designation Refer to Communications Designations for details jl A p 43 Data designation Always H hexadecimal Antenna designation Always 1 Response Command End code Retry Status Read data code RD 00 flag flag x
60. ock bytes x CR nation desig tion nation 2 1 1 4 2 2 Command code MD Communications Specifies the method for communicating with a Tag designation Refer to Communications Designations for details il A p 43 Process designation Specifies the check process K Check code calculation C Check code verification Antenna designation Always 1 Check block start address Specifies the check block start address in four hexadecimal digits Specification range 0000h to 007Dh No of check block bytes Specifies the number of check block bytes in two hexadecimal digits Specification range 03h to 80h Response Command End code Retry Status code MD 00 flag flag x spueululio suoneoiunuluo KA TeTEeE ES Status flag Shows the check code verification result 0 Verification normal 1 Verification error Example Adding a Check Code to 4 Bytes of Data from Address 0010h Single Auto Send data MDSAK1001006 CR Receive data MD0000x CR The specified number of bytes will be 6 with 2 bytes of check code attached to 4 bytes of data au Do not write required data in the last two bytes of the area These two bytes are used to record the check code Refer to Memory Check Function for details e Fe CHECK A p 32 a Electromagnetic Inductive RFID System 48 User s Manual SECTION 4 Commands Tag Function Designation TF Sets clears
61. ommand After sending a com mand check the indicator to be sure that the CF Reader Write has received the command Host device CF Reader Writer Executes reset processing Single Response One response is returned for one command when single auto SA is specified in a command for com municating with Tags when commands that are not for communicating with Tags communications subcommand controller control commands or host commands are specified when appraisal com mands are specified etc Host device CF Reader Writer Multiple Responses Multiple responses are returned for one command when repeat auto RA is specified in a command for communicating with Tags Host device CF Reader Writer MO 4 osuodsoy PpueWWOD FAIRER P Z Pa Z Response Response Response Response Electromagnetic Inductive RFID System User s Manual SECTION 4 Commands Command List There are 5 main types of commands Communications Commands Communications commands to communicate with Tags Command aay Reference code Name Description page RD Read Reads Tag memory data p 44 WT Write Writes data to Tag memory p 45 CW Computation Write Writes memory data and the calculation result to Tags p 46 DF Data Fill Writes designated data to a designated area p 47 MD Memory Check Sets and verifies Tag memory check codes p 48 TF Tag Function Designation Sets clears the write protection for Tags p 49 ID ID Read Reads
62. rt address to a Tag Command Communica Data Antenna Write area start No of write Write data code WT tions designa desig designa address bytes tion na tion tion 2 2 1 1 4 2 Specified number of bytes 2 Communications Specifies the method for communicating with a Tag designation Refer to Communications Designations for details il a p 43 Data designation Specifies the data format when sending write data to Tags A ASCII H Hexadecimal Antenna designation Always 1 Write area start address Specifies the start address in the Tag memory area for writing data in four hexadecimal digits Specification range 0000h to 007Fh No of write bytes Specifies the number of bytes of data to be written to the Tag in two hexadecimal digits Specification range 01h to 80h Write data Data written to Tags There will be 2 characters per byte if hexadecimal is specified Response End code Retry Status 00 flag flag CR 2 1 1 2 Example Writing 4 Bytes of Data 11223344 from Address 0010h Single Auto Hexadecimal Send data WTSAH10010041 1223344x CR Receive data WTOOO0 CR Command code WT Specify the total number of write bytes so that the sum of the write area start address and the number of bytes does not A exceed the Tag memory capacity 128 bytes m Example The number of bytes can be specified between 01h and 70h for a start address of 001
63. s believed to be accurate however no responsibility is assumed for clerical typographical or proofreading errors or omissions PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user s programming of a programmable product or any consequence thereof COPYRIGHT AND COPY PERMISSION This document shall not be copied for sales or promotions without permission This document is protected by copyright and is intended solely for use in conjunction with the product Please notify us before copying or reproducing this document in any manner for any other purpose If copying or transmitting this document to another please copy or transmit it in its entirety Electromagnetic Inductive RFID System User s Manual Introduction Standard Conformity 1 FCC Rules Federal Communications Commission This product complies with Part 15 Subpart C of the FCC Rules FCC ID E4E 6CY CIDV6700104 FCC NOTICE This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s author ity to operate the equipment 2 EC Declaration of Conformity Hereby OMRON Corporation declares that this RFID System and a
64. shows the commands and available designation range for specifying start addresses and number of bytes in commands If a value outside the available range is specified a command error will occur Command code Ranges for start address and number of bytes Other restrictions Read RD A Start address 0000h to 007Fh lt B No of bytes 01h to 80h SM Write WT A Start address 0000h to 007Fh lt B No of bytes 01h to 80h AtB S 80h Computation Write CW A Start address 0000h to 007Fh A B lt 80h B Calculation area 01h to 04h Data Fill DF A Start address 0000h to 007Fh A lt B B End address 0000h to 007Fh Memory Check MD A Start address 0000h to 007Dh A B lt 80h B No of check bytes 03h to 80h If the start address is 20h and the number of bytes is 70h the result is A B 90h which gives a command error 1euu04 osuodsoy pueuiuo EATeTEer Electromagnetic Inductive RFID System User s Manual 3 SECTION 4 Commands Command Response Flow The command received from the Handy Terminal by the CF Reader Writer may be different to the response sent to the Handy Terminal from the CF Reader Writer depending on the type of command and the communications designation No Response If the CF Reader Writer receives a reset command it sends no response performs reset processing and waits for the next command The indicator will light green when the CF Reader Writer receives a c
65. suoneoyioeds IETNSJTRET 77 suoisueuiig pue suoneouyioeds TNSTRETS SECTION 6 Appendices e m Q z CHECK Read and write communications with Tags is performed in 4 byte units This means that the communi cations time can be minimized by specifying the address and number of bytes so that the write start address is a multiple of 4 Example If 4 bytes of data is to be written from address 0001h change the address to 0000h If the system configuration is such that the address cannot be changed like this the times on the fol lowing table must be added to the communications time When write protection is used 2 9 ms When the start address is not a multiple of 4 42 9 ms When the end address start address number of addresses is not a multiple of 4 2 9 ms TAT The TAT is the time from the start of command transmission by the host device to the end of response reception by the Handy Terminal TAT can be calculated from the communications time and the number of command response characters The formula is shown below TAT Command transmission time Communications time Response transmission time Bits per character Transmission time Baud rate bps The transmission time depends on the number of bits per character and the communications condi tions baud rate data length parity and stop bits This formula applies when there is no interval between Handy Terminal command characters i e
66. tection function is a protective function designed to prevent fixed data such as palette information or product information stored in a Tag memory from being erased by accidental overwriting Any area of specified addresses can be write protected a maximum of two areas by setting protection information in the Tag A protection error will occur if a write is executed for any write protected page Part of the user data area 0000 to 0003 is used for protection area information To enable write protection write the protection area information to a specified address and then use the Tag Function Setting command TF to specify Protection Setting in the process designation parameter Similarly to disable write protection specify Disable in the process designation parameter o m 9 wt Refer to Tag Function Designation TF when using the write protection function fe bres z e A pas o CHECK o p p T Relationship between Protection Information and Protection Area 3 P User address Description Data example 2 0000 Start address of write protection area 1 05h S 3 0001 End address of write protection area 1 10h 0002 Start address of write protection area 2 70h 0003 End address of write protection area 2 75h 0004 0005 Write protection area 1 0010 0011 006F User area 0070 Write protection area 2 0075 0076
67. ter combines the V670 series Antenna and Controller into a single unit with a CF interface It has superior portability and operability because it can be used by slotting it into a CF card slot Type II on a Handy Terminal Tag data can be read and written using serial communications from the Handy Terminal Protective Cover V670 A75SH155S For Sharp model V670 A75SY8046 For Symbol Technology model Handy Terminal RZ N155S Manufactured by Sharp PDT8046 Manufactured by Symbol Technology The following three types of ID Tags Tags can be used with the CF Reader Writer Model Description V670 D13F03 The V670 D13F03 ID Tag has a memory capacity of 128 bytes It is a 40 x 40 mm square tag with water resistant properties It also uses a highly effi cient non volatile ferroelectric memory called FeRAM as internal mem ory FeRAM has a semipermanent life i e it can be accessed 1 billion S times Z N V670 D13F01 The V670 D13F01 ID Tag is an 8 x 16 mm rectangular tag It is highly chemical resistant because a PPS case and highly chemical resistant epoxy resin is used on the exterior It has the same memory capacity and performance as the V670 D13F03 V670 D13F01H The V670 D13F01H ID Tag has the same performance and construction as the V670 D13F01 It has holes for easy mounting tr Refer to Tags for detailed Tag specifications lt a jl A p 70 CHECK Ferroelectric memory FeRAM
68. the Tag user ID p 51 E Communications Subcommand The communications subcommand aborts command execution po ee EMS EK A ip Description code page Command Processing Abort Aborts communications with a Tag E Controller Control Commands Controller control commands stop communications with Tags reset the CF Reader Writer etc Command A Reference Name Description code page SP Parameter Setting Sets all CF Reader Writer parameters p 53 XZ Reset Resets the CF Reader Writer p 54 il Host Commands Host commands test communications between the CF Reader Writer and the Handy Terminal Command dh Reference Name Description code page Test Checks the status of communications between the Handy Terminal p 55 TS and the CF Reader Writer Returns data received from the Handy Terminal to as is vs Version Information Reads the CF Reader Writer model information software version p 55 and creation date Electromagnetic Inductive RFID System User s Manual 1sr1 puewwoy EAYTSJTRETS 41 SECTION 4 Commands E Appraisal Commands Appraisal commands investigate the occurrence of ambient noise and evaluate communications stabil ity Command T Reference Name Description code page NS Noise Measurement Detects noise level p 56 EN Error Noise Detection Detects noise above a certain level p 57 SF Stability Evaluation Reads data from the
69. tics Data Based on Operating Conditions 79 Mutual Interference between Tags 79 Influence of Metal behind Tags Reference 80 Chemical Resistance of Tags 82 44 Memory Map 83 Maintenance and Inspection 84 44 Table of JIS8 Unit Code ASCII 85 Degree of Protection 86 Electromagnetic Inductive RFID System User s Manual 9 e Ee ELS 67 SECTION 6 Appendices Specifications and Dimensions CF Reader Writer E General Specifications Item Specifications Power supply voltage 3 3 V 15 5 0 V 15 Ambient operating 0 to 40 C temperature Ambient operating 35 to 85 with no condensation humidity Ambient storage 25 to 65 C temperature Ambient storage 35 to 85 with no condensation humidity Weight Approx 28 g Current consumption 200 mA max power supply voltage 3 3 V Material ABS black SUS Vibration resistance 1 to 150 Hz single amplitude 0 1 mm acceleration 15 m s Performed 10 sweeps for 8 minutes each in upward downward right left forward and backward directions along 3 axes Shock resistance Imposed impact of 150 m s 3 times each in upward downward left right forward and backward directions Insulation resistance 20 MQ min at 100 VDC between connector terminals and case Dielectric strength 1 000 VAC 50 60 Hz 1 min Impressed between connector terminals and case leakage current 1 mA max E Performance Specifications It
70. tive 1999 5 CE Swedish H rmed intygar Omron att den RFID System Antenn V670 H11 Serie V670 H51 Serie V670 H51Q Serie och Kontrollant V670 CD1D Serie st r 1 ve rensst mmelse med de v sentliga egenskapskrav och vriga relevanta bestimmelser som framgar av direktiv 1999 5 EG Danish Undertegnede Omron erkl rer herved at f lgende den RFID System Antenne V670 H11 Serie V670 H51 Serie V670 H51Q Serie og Kontroll r V670 CDID Serie overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF German Hiermit erkl rt Omron die RFID System Antenne V670 H11 Serie V670 H51 Serie V670 H51Q Serie und Kontrolleur V670 CDID Serie in berein stimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999 5 EG befindet BMWi Greek ME THN IIAPOYSA Omron AHAONEI RFID OYOTHMA KEPAIA V670 H11 OEIPA V670 H51Q OEIPA KAI KOYPOAHPY V670 CDID OEIPA SYMMOPF ONETAI IPOS TIS OYSIOAEIS ATIAITHSEIS KAI TIS AOIIIES SXETIKES AIATAEEIS THS OAHTIAS 1999 5 EK Italian Con la presente Omron dichiara che la RFID Sistema Antena V670 H11 Serie V670 H51 Serie V670 H51Q Serie e Controlleur V670 CD1D Serie sono conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Spanish Por medio de la presente Omron declara que el RFID Sistema Antena V670 H11 Serie V670 H51 Serie V670 H51Q Serie y Controlador V670 CDID Serie esta conforme a
71. write protection for Tags Command Communica Proc Antenna code TF tions desig ess desig nation desig nation id CR nation 2 2 1 1 2 Communications Specifies the method for communicating with a Tag designation Refer to Communications Designations for details jl A p 43 Process designation Specifies setting or clearing the function P Sets protection R Clears protection Antenna designation Always 1 Response Command End code Retry Status code TF flag flag x CR 2 2 1 1 2 E Setting Example Relationship between Protection Information and Protection Area SPUBLWILUOD suomneoiunuluilo EAREN User address Description Data example 0000 Start address of write protection area 1 05h 0001 End address of write protection area 1 10h 0002 Start address of write protection area 2 70h 0003 End address of write protection area 2 75h 0004 0005 Write protection area 1 0010 0011 006F User area 0070 Write protection area 2 0075 0076 007F Protection area setting range 0004h to 007Fh Electromagnetic Inductive RFID System User s Manual 49 spueululio suoneoiunuluo KA TeTEeE ES 50 SECTION 4 Commands e No Write Protection When write protection is not set for the Tag Send data TFSAR1 x CH Receive data TF0000x CR e Write Protection Specified for One L
72. xcept subcommands When a command is received the CF Reader Writer enters the command processing status e Command Processing Once a command has been received the CF Reader Writer ignores the next command until process ing of the received command has been completed Command processing abort and reset commands however can always be received Electromagnetic Inductive RFID System User s Manual SECTION 4 Commands Command Response Format Command Frames Command code Data Terminator ee Te n 2 Name Command code Description Specifies the command Data Specifies the parameters for command execution address number of bytes etc or specifies the data to be written Terminator Indicates the end of a command using the two characters 2A and the carriage return code 0D Response Frames Status Command code Endcode Retry flag flag Data Terminator 2 1 1 2 n 2 Name Description Command code The same data as the sent command frame is added and returned End code Shows the command execution result Retry flag Always 0 Status flag A code that shows the status of command execution 0 Normal Indicates that the processing was completed normally 1 Tag data status Indicates that the verification result of the Memory Check command MD detected an error or that an overflow underflow occurred in the calculation of a Computation Write command CW 2

V670 Series User`s Manual - Products

Contents

Download Pdf Manuals

Related Search

Related Contents