Telic STD35 Camera Installation Guide
Contents
1. Telic Telematics amp Telemetry Telic STD35 Camera Installation Guide Version 1 0 Telic GmbH Internet www telic de E mail info telic de 1 e E O POT OI O Tel Atenton please red UMS a cid Z E O A tet die ZA Me oe tas al decia 2 2 gt A ct tS E to etestuel te mites 2 3 Enabling Camera in SOM rai edita de DOCUMEN MISIO iodo 1 Introduction Thank you very much for purchasing our Telic STD35 telemetry device and optional Telic Camera We wish you success and joy in using your new STD35 The STD35 offers the possibility to monitor an object or a room with the help of the optional Telic camera for the STD35 You can retrieve an actual picture form the STD35 using any computer worldwide that is connected to the internet e g to check the weather conditions at your holiday home In addition a picture can be sent as an attachment to the preconfigured e mail address in the case of an alarm This allows you to take further action if necessary e g call the police if you see a burglar on the photo To be able to use this functionality you only have to connect the Telic camera to the camera plug on the STD35 see picture 1 After the software of the STD35 has recognized the camera the pictures can be viewed our sent via e mail in the following ways Access of the web browser through the internet and click on Photo Page E mail with JPEG attachment in alarm situation E mail with JPEG attachment after inc2. rubber seal Push the connector through the cap of the Grommet Then while the seal is still outside the grommet open the seal slightly where it has been cut and thread the connector through the cut Do not worry that you have cut the seal when it is re inserted in the grommet the force of the grommet will close the area where it has been cut Once the connector is through the seal it can then be pushed through the grommet and the seal and cap can be returned to there original positions 2 3 Enabling Camera in Software You can deactivate the camera functionality when the camera is connected to the STD35 with the command CAM 0 and activate it with CAM x The camera offers different resolutions and you can select the desired camera resolution x 1 80 x 60 3 160 x 120 5 320 x 240 7 640 x 480 The default value is 7 For more details on correct software operation of the Camera module please see the STD35 user manual 3 Document history Revision Datum Changes Rev 1 0 16 Dec 2010 Original file Imprint These operating instructions are published by Telic GmbH No reproduction including translation is permitted in whole or part e g photocopy microfilming or storage in electronic data processing equipment without the express written consent of the publisher The operating instructions reflect the current technical specifications at time of print We reserve the right to change the technical or physical specifi
3. anual has been thoroughly checked should you nevertheless find an error or want to express criticism or make suggestions please send an e mail to E mail support telic de Oberhaching 16 Dec 2010 2010 Telic GmbH Oberhaching Germany 1 1 Attention please read this This user manual contains important information regarding installation of the Telic Camera module in an STD35 Read it carefully before attempting to start working with the STD35 if the Camera module will be used The warranty will be null and void should damage occur due to non compliance with these instructions for use We cannot accept any responsibility for consequential loss We cannot be held responsible for material loss or personal injury that is due to incompetent use or non compliance with the safety instructions The warranty will be null and void in such circumstances The STD35 and optional camera contain highly integrated components which can be damaged by electrostatic discharge A Therefore only touch the STD35 case and avoid touching the pins of components on the board A Safety Instructions When using products which are exposed to electric voltage the valid VDE regulations have to be observed Especially VDE 0100 VDE 0550 0551 VDE 0700 VDE 0711 and VDE 0860 are applicable e All wiring work has to be done in a voltage free state only e All cables and wires which are energized and connected to the device the module or components have to be check
4. cations Copyright 2010 by Telic GmbH printed in Germany Telic GmbH Raiffeisenallee 12b D 82041 Oberhaching Germany www telic de Telic reserves the right to change correct and or improve the content any time and without prior notice without being obliged to do so No responsibility is taken for the correctness of the information
5. ed or which parameters these components are allowed to have a specialist must be contacted e Devices which operate with greater than 35 Volts have to be connected by a specialist e Before putting the device into operation it should be checked that there is no current leakage on the housing e in case measurements with the opened housing are necessary an isolating transformer has to be used for safety reasons Alternatively the voltage can be supplied by an appropriate power supply which complies with the safety regulations All wiring work has to be done in a voltage free state only 2 Installing the Camera 2 1 The Connector Inside the STD35 is the camera connector The connector is designed to pair with the connector of the Telic Camera module There is a small tab on the Camera Module connector that ensures that the connector can only be inserted in the correct orientation Camera Connector 2 2 Mechanical Assembly Because of the size of the Telic Camera modules connector and the fact that the STD35 housing is sealed using water resistant Grommets some minor mechanical modification is required to bring the connector through the Grommet without significantly compromising the water resistance of the device The way to get the connector to fit through the Grommet is to first cut the top bar off the Telic Camera module s connector Then remove the Grommet Cap and the grey rubber seal inside the grommet and cut it along the side of the
6. ed regularly for any damage to the isolation shielding or fractures in the cables If the supply cables are visibly damaged the device has to be taken out of operation immediately until the faulty cable has been exchanged e Before putting a device into operation it has to be clarified whether this device or module is appropriate for the field of application In case of doubt ask a specialists or the manufacturer of the device e Please note that we are not responsible for any errors in usage or connection Therefore we cannot accept any responsibility for consequential loss e Before opening the device always disconnect the mains adapter or make sure that the device is disconnected from the power supply e Components modules or devices have to be built into a housing before they are put into operation During installation they should not be connected to any power supply e You should only use tools on components modules or devices if they are disconnected from the power supply and residual electric charge which may still be stored in some components inside the device has been discharged e When using components or modules it is necessary to strictly observe the specification given in the corresponding description of these components e f a description for a private end customer does not clearly state which electric data is valid for a component or a module how to wire the device which external components or additional devices can be connect
7. oming call E mail with JPEG attachment after SMS request In case the light intensity is not enough at the survey area the infrared light of the camera will be activated automatically Please note that due to the infrared light there will be a loss of colours in the picture The Telic camera has an adjustable sun shade metal plate over the camera Please take into consideration when adjusting the sun shade that the shadows are often changing during the day TIP To make sure that all desired objects will be in the picture that the sun shade is in a good position and or that the illumination of the room will lead to satisfactory picture we recommend to take test pictures after the installation Only then you can rely on the full functionality of the Telic camera Concerning the user manual This document is meant to help you use the various functions of the device in the most optimal way possible Therefore we ask you to please read this manual carefully and completely The information in this document has been gathered after thorough investigation but should not to be taken as assurance of end product properties The written approval of Telic GmbH is mandatory before you can pass on or reproduce this documentation for this product or the software or use the content Telic reserves the right to change the data mentioned here without prior notice and does not take any responsibility for technical inaccuracies and or omissions This m
Download Pdf Manuals
Related Search