C-Tick EMC TEST REPORT
Contents
1. Reading Corr Emiss Level Limit 3m Margin MHz dBuV Factor Pk Pk dB dB m dBuV m dBuV m 1009 27 59 75 12 71 47 04 79 50 32 46 1112 23 57 00 12 20 44 80 79 50 34 70 1186 51 54 00 11 84 42 16 79 50 37 34 1489 77 57 75 10 35 47 40 79 50 32 10 1615 49 58 25 9 64 48 61 79 50 30 89 2495 39 54 25 6 75 47 50 79 50 32 00 Note In case of peak reading complied with the limit at least 22dB margin no measurement with A V detector required Radiated Emission Above 1GHz B Model PID 426WD Test Mode Mode 1 Temperature 33 C Humidity 56 RH Detector Function Pk A V Antenna Horizontal at 3m Test By Tony Tsai Test Results Pass The chart below shows the highest readings taken from the final data Freg Reading Corr Emiss Level Limit 3m Margin MHz dBuV Factor Pk Pk dB dB m dBuV m dBuV m 1009 43 57 00 12 71 49 29 79 50 30 21 1086 71 56 75 12 33 49 42 79 50 30 08 1112 71 57 00 12 20 49 80 79 50 29 70 1186 43 56 50 11 84 49 66 79 50 29 93 1286 71 58 25 11 34 51 91 79 50 27 59 1312 57 54 25 11 22 48 03 79 50 31 47 Note In case of peak reading complied with the limit at least 22dB margin no measurement with A V detector required Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 APPENDIX I PHOTOGRAPHS OF TEST SETUP LINE CONDUCTED EMISSION TEST ME T me e Lo A Lu Lai E y 3 a2. 20 10 18 00 12100 Peak 10 758 00 2548 232 2780 4700 1920 0 00 10000 Peak Page 18 Rev 00 Compliance Certification Services Inc Report No 1100830368 C Date of Issue Aug 30 2010 Radiation Emission B CCS Radiated Test OATS 1 Job No T100702109 Ant Polar Ver Standard CISPR 22 Class A Tested Distance 10m Test Item Radiated Emission Date 2010 8 25 Temp C Hum RH 33 C 63 RH Time PM 16 18 Company TYT Tested By Tony Tsai Model PID 426WD Test Mode Mode 1 dBuWim sio 600 700 800 1000 Frequency MHz uma imu ruca Bev Buvim B Cb Gm o No MA EA EC mE ae ae 4 an 1 7000 4149 1809 2340 4000 2 7840 4209 1669 2540 40 00 14 60 19710 400 00 Peak 6 24490 3901 941 29 60 4700 1740 25180 400 00 Peak 7 30553 4409 687 3722 4700 978 0 00 30330 Peak 8 54020 3157 L57 3000 4700 17 00 0 00 13490 Peak 9 74340 2897 203 3100 4700 1600 0 00 10000 Peak Page 19 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 Radiated Emission Above 1GHz A Model PID 426WD Test Mode Mode 1 Temperature 33 C Humidity 56 RH Detector Function Pk A V Antenna Vertical at 3m Test By Tony Tsai Test Results Pass The chart below shows the highest readings taken from the final data Freq
3. 22 Class A Test Item Conduction Emission Date 2010 08 24 Temp C Hum RH 25 C 53 RH Time AM 11 05 Company TYT Tested By Eason Model PID 426WD Test Mode Mode 1 1000 dBuV QP AWG 1 2 L 5 g 50 0 0 0 150 0 5 MHz 5 30 000 Quasi Average Correction Quasi Average Quasi Average Quasi Average Remark NO Frequency Peak reading factor Peak result Peak limit Peak margin reading result limit margin MHz dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB Pass Fail l 0 2571 42 70 31 82 9 65 52 35 41 47 79 00 66 00 26 65 24 53 Pass 2 0 3831 47 79 43 56 9 65 57 44 53 21 79 00 66 00 21 56 12 79 Pass 3 0 6388 44 93 37 87 9 55 54 48 47 42 73 00 60 00 18 52 12 58 Pass 4 0 9044 42 40 31 21 9 56 51 96 40 77 73 00 60 00 21 04 19 23 Pass 5 1 1444 41 95 30 73 9 57 51 52 40 30 73 00 60 00 21 48 19 70 Pass 6 1 4006 41 18 28 69 9 60 50 78 38 29 73 00 60 00 22 22 21 71 Pass L1 Line One Live Line Page 16 Rev 00 Compliance Certification Services Inc Report No T100830368 C Linkou Conduction 4 Date of Issue Aug 30 2010 Job No 1100830368 Line L2 Standard CISPR 22 Class A Test Item Conduction Emission Date 2010 08 24 Temp C Hum RH 25 C 53 RH Time AM 11 46 Company TYT Tested By Eason Model PID A426WD Test Mode Mode 1 1000 dBu OP AVG 1 2 4 5 6 50 0 0 0 150 0 5 MHz 5 30 000 Frequency Quasi Average Correction Quasi Average Quasi Aver
4. Certification Services Inc Y gt Report No T100830368 C Date of Issue Aug 30 2010 3 2 DECISION OF FINAL TEST MODE 1 The following test mode was scanned during the preliminary test Mode 1 1360 x 768 Resolution 60Hz Mode 2 1024 x 768 Resolution 75Hz Mode 3 800 x 600 Resolution 75Hz Mode 4 DVI Mode 5 HDMI 2 After the preliminary scan the following test mode was found to produce the highest emission level Mode 1 Then the EUT configuration and cable configuration of the above highest emission mode was chosen for all final test items Page 6 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 4 SETUP OF EQUIPMENT UNDER TEST Setup Diagram See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment support Equipment Equipment Modi Serial No No rcc ID Trade Name Name Data Data Cable VGA Cable Shielded 1 8m DX 6120 SGH5330GK7 FCC DoC with two cores Unshielded 1 8m Audio Cable Unshielded 1 8m Modem DM nw 14 304012266 IFAXDM1414 ACEEX Shielded 12m 2m Unshielded 1 8m 8m E IE aa eae mom emo om mm dem RC Note All the above equipment cable was placed in worse case positions to maximize emission signals during emission test Grounding Grounding was in accordance with the manufacturer s requirements and conditions for the intended use Page 7 Rev 00 R
5. Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 C Tick EMC TEST REPORT For 46 LCD Monitor Model PID 426WD Trade Name TYT Non Brand Issued for Tiun Yuan Technology Co Ltd 6F No 37 Lane 221 Gang Oian Road Nei Hu Taipei 114 Taiwan R O C Issued by Compliance Certification Service Inc No 81 1 Lane 210 Pa De 2 Rd Luchu Hsiang TAF Taoyuan Shien 338 Taiwan R O C TAF TEL 886 3 3245966 0363 FAX 886 3 3245235 ACCREDIT No 0824 01 Note This report shall not be reproduced except in full without the written approval of Compliance Certification Services Inc Ltd This document may be altered or revised by Compliance Certification Services Inc personnel only and shall be noted in the revision section of the document Page 1 Total Page 21 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 TABLE OF CONTENTS L TEST KESULI CBRLDIEICATIONN sen an WE peu PI Ra pb 3 2 BUT DESCRIPTION rrarena son Say TOM UI IRE ERU TRITUM AI E GAK REO MEUM OMM 4 gt TEST iss Bele OC ae an UNE MUN pk aaa 5 cL BUSI E MOP NON sudes paraga anan an cup es 5 32 DECISION OF FINAL TEST MODE ee 6 4 SETUP OF EQUIPMENT UNDER TEST eese yl 5 FACILITES AND ACCREDICATI N Sur utes naat ae aer EI PI PIE 8 dsk RAN PES e e o A A E E EEES 8 5 2 LABORATORY ACCREDITIONS AND LISTING IH 9 6 INSTRUM
6. ENT AND CALIDISALION iptsobs rentetan 10 6 1 MEASURING INSTRUMENT CALIBRATION mm 10 6 2 TEST AND MEASUREMENT EQUIPMENT in 10 7 LINE CONDUCTION amp RADIATION EMISSION TEST 11 TA LIM Ra 11 7 2 TEST PROCEDURE OF LINE CONDUCTION EMISSION eee 12 7 3 TEST PROCEDURE OF RADIATION EMISSION RI Hmmm 14 Je OFP OLD a aaa aaa aa sa aa oo a aa eee er en NA eee 16 APPENDIX PHOTOGRAPHS OF TEST SETUP concisa taras 21 Page 2 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 1 TEST RESULT CERTIFICATION Applicant Tiun Yuan Technology Co Ltd 6F No 37 Lane 221 Gang Qian Road Nei Hu Taipei 114 Taiwan R O C Manufacturer Tiun Yuan Technology Co Ltd 6F No 37 Lane 221 Gang Qian Road Nei Hu Taipei 114 Taiwan R O C Equipment Under Test 46 LCD Monitor Trade Name TYT Non brand Model PID 426WD Detail EUT Description See Item 2 of this report Date of Test Aug 23 27 2010 Applicable Standard Class Limit Test Result AS NZS CISPR 22 2006 Class A Required Limit No non compliance noted Deviation from Applicable Standard None The above equipment was tested by Compliance Certification Services Inc and found compliance with the requirements set forth in the technical standards mentioned above The test results of testing in this report apply only to the product system
7. Page 21 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 EX ur Xr HP a VIN US E A
8. age Quasi Average Remark NO Peak reading factor Peak result Peak limit Peak margin reading result limit margin MHz dBuV dBuV dB dBuV red Sea dBuV dB dB Pass Fail 1 0 2541 40 79 31 60 9 66 50 45 66 00 28 55 24 74 Pass 2 0 3813 48 05 44 41 9 66 57 71 e 5 de 66 00 21 29 11 93 Pass 3 0 6374 45 35 38 54 9 56 54 9 48 10 73 00 60 00 18 09 11 90 Pass 4 0 9123 42 42 30 30 9 57 51 99 39 87 73 00 60 00 21 01 20 13 Pass 5 1 1423 42 08 31 42 9 58 51 66 41 00 73 00 60 00 21 34 19 00 Pass 6 1 4063 41 29 27 92 9 61 50 90 37 53 73 00 60 00 22 10 22 47 Pass L2 Line Two Neutral Line Page 17 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 Radiation Emission A CCS Radiated Test OATS 1 Job No T100702109 Ant Polar Ver Standard CISPR 22 Class A Tested Distance 10m Test Item Radiated Emission Date 2010 8 25 Temp C Hum RH 33 C 63 RH Time PM 14 15 Company TYT Tested By Tony Tsai Model PID 426WD Test Mode Mode 1 dBu m sio 600 700 800 1000 Frequency MHz a imu racism Bev avi B C Gm o No MHz dBuV E C BN ae dB cm 1 6500 4608 1838 2770 4000 2 7816 3250 16 73 3577 4000 423 12970 10000 QP 6 24610 3765 925 2840 4700 18 60 25420 400 00 Peak 8 458 60 3094 294 2800 4700 19 00 17640 14410 Peak 9 64470 2650 040 2690 4700
9. d using an AV Detector The test data of the worst case condition s was recorded Test Setup Vert reference plane EMI receiver Heference ground plane For the actual test configuration please refer to the related item Photographs of the Test configuration Data Sample Margin Remark dBuV dBuV dBuV dBuV Freq Emission frequency in MHz Raw dBuV Uncorrected Analyzer Receiver reading Corr Factor dB Antenna factor Cable loss Amplifier gain Result dBuV Raw reading converted to dBuV and CF added Limit dBuV Limit stated in standard Margin dB RAW dBuV Limit dBuV Q P Quasi Peak Page 13 Rev 00 E Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 7 3 TEST PROCEDURE OF RADIATED EMISSION Procedure of Preliminary Test The equipment was set up as per the test configuration to simulate typical actual usage per the user s manual When the EUT is a tabletop system a wooden turntable with a height of 0 1 meters is used which 1s placed on the ground plane When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane Support equipment if needed was placed as per AS NZS CISPR 22 All I O cables were positioned to simulate typical actual usage as per AS NZS CISPR 22 The EUT received AC power source 240VAC 50Hz
10. e EUT using a EMI Test Receiver connected to the LISN powering the EUT The LISN has two monitoring points Line 1 Hot Side and Line 2 Neutral Side Two scans were taken one with Line 1 connected to Receiver and Line 2 connected to a 50 ohm load the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Receiver The Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes During the above scans the emissions were maximized by cable manipulation The test mode s described in Item 3 2 were scanned during the preliminary test After the preliminary scan we found the following the test mode described in Item 3 2 producing the highest emission level The EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing Page 12 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 Procedure of Final Test FUT and support equipment was set up on the test bench as per step 10 of the preliminary test Ascan was taken on both power lines Line 1 and Line 2 recording at least the six highest emissions Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit If EUT emission level was less 2dB to the AV Limit in Q P mode then the emission signal was re checke
11. eport No T100830368 C Date of Issue Aug 30 2010 Compliance Certification Services Inc 5 FACILITIES AND ACREDITATIONS FACILITIES All measurement facilities used to collect the measurement data are located at CCS Taiwan Linkou Lab at No 81 1 Lane 210 Bade Rd 2 Luchu Hsiang Taoyuan Hsien Taiwan The measurement facilities are constructed in conformance with the reguirements fo CISPR 16 1 ANSI C63 4 and other equivalent standards Page 8 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 LABORATORY ACCREDITATIONS AND LISTINGS The test facilities used to perform Electromagnetic compatibility tests are registered or accredited by the organizations listed in the following table which includes the recognized scope specifically This accredited organization maintains A2LA accreditation to ISO IEC 17025 for the specific test listed in A2LA Certificate 0824 01 EN 55011 EN 55014 1 2 CISPR 11 CISPR 14 1 2 EN 55022 EN 55015 CISPR 22 CISPR 15 AS NZS 3548 VCCI V3 2001 CFR 47 FCC Part 15 18 CNS 13783 1 CNS 13439 CNS 13438 CNS 13803 CNS 14115 EN 55024 IEC 801 2 IEC 801 3 IEC 801 4 IEC EN 61000 3 2 EIC EN 61000 3 3 IEC EN 61000 4 2 3 4 5 6 8 11 EN 50081 1 EN No 0824 01 61000 6 3 EN 50081 2 EN 61000 6 4 EN 50081 2 EN 61000 6 1 2001 3 10 meter Open Area Test Sites to perform FCC C Part 15 18 measurements 93105 90471 3 10 mete
12. from the outlet socket under the turntable All support equipment received power from another socket under the turntable The antenna was placed at 10 meter away from the EUT as stated in AS NZS CISPR 22 The antenna connected to the Spectrum Analyzer via a cable and at times a pre amplifier would be used The Analyzer Receiver quickly scanned from 30MHz to 40GHz maximum if any The EUT test program was started Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level The test mode s described in Item 3 2 were scanned during the preliminary test After the preliminary scan we found the following the test mode described in Item 3 2 producing the highest emission level Then the EUT and cable configuration antenna position polarization and turntable position of the above highest emission level were recorded for the final test Page 14 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 Procedure of Final Test FUT and support equipment were set up on the turntable as per step 8 of the preliminary test The Analyzer Receiver scanned from 30MHz to 40GHz maximum if any Emissions were scanned and measured rotating the EUT to 360 degrees varying cable placement and positioning the antenna 1 to 4 meters abo
13. n measured at 10 meter 30 230 Note The lower limit shall apply at the transition frequency Maximum permissible level of Radiated Emission measured at 3 meter Note The lower limit shall apply at the transition frequency Page 11 Report No T100830368 C Date of Issue Aug 30 2010 Rev 00 E Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 7 2 TEST PROCEDURE OF LINE CONDUCTED EMISSION Procedure of Preliminary Test The EUT was set up as per the test configuration to simulate typical actual usage per the user s manual When the EUT is a tabletop system a wooden table with a height of 0 8 meters is used and is placed on the ground plane as per AS NZS CISPR 22 see Test Facility for the dimensions of the ground plane used When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane Support equipment if needed was placed as per AS NZS CISPR 22 All I O cables were positioned to simulate typical actual usage as per AS NZS CISPR 22 The test equipment EUT installed received AC power 240VAC 50Hz through a Line Impedance Stabilization Network LISN which supplied power source and was grounded to the ground plane All support equipment received power from a second LISN The EUT test program was started Emissions were measured on each current carrying line of th
14. national standards Equipment has been calibrated by accredited calibration laboratories 6 2 TEST AND MEASUREMENT EQUIPMENT The following list contains measurement equipment used for testing The equipment conforms to the requirement of CISPR 16 1 1 CISPR 16 1 2 CISPR 16 1 3 CISPR 16 1 4 CISPR 16 1 5 ANSI C63 2 and other required standards Calibration of all test and measurement including any accessories that may effect such calibration is checked frequently to ensure the accuracy Adjustments are made and correction factors are applied in accordance with the instructions contained in the respective manual Equipment Used for Emission Measurement Conducted Emission Test Site 4 Name of Equipment Serial Number Calibration Due EMI Test Receiver ESCS30 847793 012 02 26 2011 LISN ENV216 100066 05 09 2011 LISN ENV 4200 830326 016 04 09 2011 Note The measurement uncertainty is less than 1 7983dB which is evaluated as per the NAMAS NIS 81 and CISPR A 29I CDV Open Area Test Site 1 Open areata sient Note The measurement uncertainly is less than 3 36dB which is evaluated as per the NAMAS NIS 81 and CISPR A 29I CDV Page 10 Rev 00 Compliance Certification Services Inc 7 LINE CONDUCTED amp RADIATED EMISSION TEST 7 1 LIMIT Maximum permissible level of Line Conducted Emission Note The lower limit shall apply at the transition frequency Maximum permissible level of Radiated Emissio
15. r Open Area Test Sites and conducted VCCI test sites to perform radiated conducted measurements R 393 2316 725 1868 C 402 747 912 Japan EN 50081 1 2 EN 50082 1 2 IEC 61000 6 1 2 EN 50091 2 EN 50130 4 EN 55011 EN 55013 EN 55014 1 2 EN 55015 EN 55022 EN 55024 EN 61000 3 2 3 EN 61326 1 IEC 61000 4 2 3 4 5 6 8 11 EN 60601 1 2 EN 300 328 2 EN 300 422 2 EN 301 419 1 EN 301 489 01 03 07 08 09 17 EN 301 419 2 3 EN 300 454 2 EN 301 357 2 EN 300 328 1 EN 300 328 2 EN 300 220 1 EN 300 220 2 EN 300 220 3 47 CFR FCC Part 15 Subpart C EN 61000 3 2 EN 61000 3 3 CNS 13439 CNS 13783 1 CNS 14115 CNS 13438 AS NZS CISPR 22 CNS 13022 1 IEC 61000 4 2 3 4 5 6 8 11 CNS 13022 2 3 Taiwan CNS 13438 CNS 13783 1 CNS 13439 iJ undue SL2 IS E 0014 IN E 0014 A1 E 0014 R1 E 0014 R2 E 0014 L1 E 0014 Taiwan Industry da RSS212 Issue 1 Canada Z O 7 2 gt fas lt Note No part of this report may be used to claim or imply product endorsement by A2LA TAF or other government agency Page 9 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 6 INSTRUMENT AND CALIBRATION 6 1 MEASURING INSTRUMENT CALIBRATION The measuring equipment utilized to perform the tests documented in this report has been calibrated once a year or in accordance with the manufacturer s recommendations and 1s traceable under the IEC 17025 to international or
16. ve the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level Recorded at least the six highest emissions Emission frequency amplitude antenna position polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit and only Q P reading is presented O The test data of the worst case condition s was recorded Test Setup Test table amp Turntable Boundary of EUT Em Coaxial Cable Power 0 8 m Cable 3 or 10m Ground Plane E Nil Receiver For the actual test configuration please refer to the related item Photographs of the Test configuration 1 or 1m 4m Data Sample Reading EIE Result mi Margin Degree Heigh Factor Remark dBuV dB m dBuV m dBuV m dB cm Freq Emission frequency in MHz Reading dBuV Uncorrected Analyzer Receiver reading Corr Factor dB m Antenna factor Cable loss Amplifier gain Result dBuV m Reading dBuV Corr Factor dB m Limit dBuV m Limit stated 1n standard Margin dB Result dBuV m Limit dBuV m Q P Quasi Peak Page 15 Rev 00 Compliance Certification Services Inc J Report No T100830368 C Date of Issue Aug 30 2010 7 4 TEST RESULTS Line Conduction Emission Linkou Conduction 4 Job No T100830368 Line LI Standard CISPR
17. which was tested Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Approved by Reviewed by O vid Jang David Wang Ethan Huang Director of Linko Laboratory Section of Linko Laboratory Compliance Certification Services Inc Compliance Certification Services Inc Page 3 Rev 00 Compliance Certification Services Inc Vv Report No T100830368 C Date of Issue Aug 30 2010 2 EUT DESCRIPTION YO PORT OF EUT jo PORT TYPE TENTED WITH D VideolnPorevGA 2 DVI Port 3 HDMI Port 4 Audio In Port 5 Speaker Out Port L R 6 RS 323 port Note According to customer declaration the RS 323 and Service Port of EUT is for control mode and update firmware function only so didn t connect any support equipment Page 4 Rev 00 Compliance Certification Services Inc Report No T100830368 C Date of Issue Aug 30 2010 3 TEST METHODOLOGY 3 1 EUT SYSTEM OPERATION ITE EMISSION TEST 1 EMI test program was loaded and executed in Windows XP mode 2 Data was sent to EUT filling the screen with upper case of H patterns 3 PC played music from CD ROM and sent signal to EUT via an audio cable 4 Test program sequentially exercised printer then sent H patterns to them individually 5 Repeat the steps of 2 to 3 Note Test program is self repeating throughout the test Page 5 Rev 00 Compliance
Download Pdf Manuals
Related Search