Home

User Manual - Mobility Hire

Contents

1. 3 Unplug the controller connector s from the power base See figure 7 4 Flip up the seat latch safety See figure 11 5 Squeeze the seat latch and release the seat from the front trapeze bar 6 Slide the seat forward and remove it from the power base Figure 16 Seat Height Angle Adjustment 24 www pridemobility com Q6 Edge V COMFORT ADJUSTMENTS 7 Remove the hardware that attaches the trapeze bars to the seat interface weldments See figure 16 8 Move the trapeze bars up or down to the desired height NOTE Change the seat dump by raising or lowering only one trapeze bar front or rear 9 Reinstall the hardware 10 Reinstall the seat 11 Reconnect the controller to the power base Seat Position You can move the seat forward or rearward by chang ing the extrusion mounting position To change the position 1 Turn off the power to the controller 2 Make sure the power chair is in drive mode 3 Unplug the controller connector s from the power base 4 Remove the seat from the power base 5 Remove both extrusions from the bottom of the seat 6 Reposition the extrusions on a different set of mounting holes You must move both extrusions the same number of holes either forward or rear wards See figure 17 7 Fasten the extrusions back onto the bottom of the seat 8 Reinstall the seat 9 Reconnect the controller to the power base SEAT MOUNTING HOLES Figure 17 Seat Position Adju
2. 34 www pridemobility com Q6 Edge VII CARE AND MAINTENANCE CARE AND MAINTENANCE Your Q6 Edge is a sophisticated power chair Like any motorised vehicle it requires routine maintenance checks You can perform some of these checks but others require assistance from your Quantum Rehab Dealer Preven tive maintenance is very important If you follow the maintenance checks in this section as scheduled you can help ensure that your power chair gives you years of trouble free operation If you have any doubt as to your power chair s care or operation contact your Quantum Rehab Dealer VAN A N WARNING Do not service the power chair when the seat is occupied 4 Your power chair like most electrical equipment is susceptible to damage from the elements Avoid damp areas of any kind pm WARNING Direct or prolonged exposure to water or dampness could cause the power AN KEN chair to malfunction electronically and mechanically Water can cause electrical components to corrode and the chair s frame to rust Power chairs should be examined V periodically for signs of corrosion caused by water exposure bodily fluid exposure or LE incontinence Damaged components should be replaced or treated immediately a X Should your power chair come in contact with water 1 Dry your power chair as thoroughly as possible with a towel 2 Allow your power chair to sit in a warm dry place for 12 hours to allow unseen water to evapo
3. ARMREST ANGLE ADJUSTMENT CONTROLLER POSITION SEAT HEIGHT ANGLE ADJUSTMENT FOOT PLATFORM ANGLE ADJUSTMENT FOOT PLATFORM HEIGHT DEPTH ADJUSTMENT Figure 10 06 Edge Assembly View Q6 Edge www pridemobility com 21 IV ASSEMBLY Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair Contour seats are attached to the power base with the Universal Mounting System UMS The UMS con sists of universal parts that may be attached to the seat regardless of seat width or seat depth The two main components are aluminum extrusions mounted to the seat base These extrusions attach to a pair of trapeze bars that are mounted to the power base See figure 11 NOTE If your power chair is equipped with a Spe cialty Seat Synergy Seat or a TRU Balance Power Positioning System refer to the information provided in separate manuals WARNING Do not pick up the seat N frame by the armrests They are free to pivot and you may lose control of the seat if they do so To install the seat 1 Tilt the seat back and slide the rear extrusion onto the rear trapeze bar See figure 11 2 Lower the front extrusion onto the front trapeze bar until the seat locks into place 3 Flip the seat latch safety down JN WARNING Make sure the seat latch AN safety is flipped down before using your power chair 4 Install the controller and
4. Disconnect both batteries before load testing and follow the directions that come with the load tester If either one ofthe batteries fails the load test replace both of them If your power chair still does not power up contact your Quantum Rehab Dealer 40 www pridemobility com Q6 Edge VIII WARRANTY LIFETIME WARRANTY Structural frame components including platform fork seat post and frame welds TWO YEAR LIMITED WARRANTY Drivetrain including motor and brake EIGHTEEN MONTHS LIMITED WARRANTY Controllers Any attempt to open or dismantle these parts will lead to this warranty being void ONE YEAR LIMITED WARRANTY All electrical parts including battery chargers are covered for one year under warranty Any attempt to open or dismantle these parts will lead to this warranty being void BATTERIES Batteries are covered by a twelve month warranty from the original manufacturer NOT COVERED UNDER WARRANTY The following parts are classed as wear items which may under normal wear and tear require replacing These items are not therefore covered under warranty tyres positioning belts bulbs upholstery plastic shrouds motor brushes fuses and batteries Warranty will also be refused if damage is deemed to have been caused through misuse or accident for which Pride Mobility Products cannot be deemed responsible NOTE Pride Mobility Products provides parts only under warranty Your Quantum Rehab Dealer is respon sible fo
5. being transported Batteries should be secured in an upright position and protective caps should be installed on the battery terminals Batteries should not be transported with any flammable or combustible items Positioning Belts Your Quantum Rehab Dealer therapist s and other healthcare professionals are responsible for determining your requirement for a positioning belt in order to operate your power chair safely The positioning belt is not designed for use as a restraining device in a motor vehicle You should be properly belted into seats approved by the vehicle manufacturer with your power chair properly stowed for vehicle transport or secured using an optional transit securement system Positioning belts should be installed as detailed in this manual See V Comfort Adjustments Once installed the belt should be placed across the pelvis as determined by your healthcare provider Anchor points of the posi tioning belts should be located so that a projected side view angle of the pelvis is between 45 75 of horizontal depending on the user s weight posture and seat cushion thickness WARNING If you require a positioning belt to safely operate your power chair make sure it is fastened securely in order to reduce the possibility of a fall from the power chair 7 WARNING The positioning belt is not designed for use as a seat belt in a motor vehicle Nor is N your power chair suitable for use as a seat in any vehicle Anyone traveli
6. 2 After one second check the battery condition meter Make sure that it remains on 3 Slowly push the joystick forward until you hear the electric brakes click Immediately release the joystick You must be able to hear each electrical brake operating within a few seconds of joystick movement Repeat this test three times pushing the joystick rearwards then left and then right Monthly Checks Check for drive tyre wear See your Quantum Rehab Dealer for repair B Check the castor wheels for wear Replace them as necessary B Check the castor forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings replaced See your Quantum Rehab Dealer for repair B Check the entire power chair for loose hardware and changes in the function or performance of the power chair See your Quantum Rehab Dealer for service or repair Keep your power chair clean and free of foreign material such as mud dirt hair food drink etc B Spring shocks and gas dampers should be visually checked for any abnormality structure damage or bent rods See your Quantum Rehab Dealer for repair Yearly Checks Take your power chair to your Quantum Rehab Dealer for yearly maintenance especially if you use your power chair on a daily basis This helps ensure that your power chair is functioning properly and helps prevent future complications 36 www pridemobility com Q6 Edge Vil CARE AND MAINTENANCE Storage Your
7. If you do not receive a complete delivery please contact your Quantum Rehab Dealer immediately Where damage has occurred during transport either to the packaging or content please contact the delivery com pany responsible INFORMATION EXCHANGE We want to hear your questions comments and suggestions about this manual We would also like to hear about the safety and reliability of your new power chair and about the service you received from your Quantum Rehab Dealer Please notify us of any change of address so we can keep you apprised of important information about safety new products and new options that can increase your ability to use and enjoy your power chair Please feel free to contact us at the address below Pride Mobility Products Ltd 32 Wedgwood Road Bicester Oxon OX26 4UL NOTE If you ever lose or misplace your product registration card or your copy of this manual contact us and we will be glad to send you a new one immediately 4 www pridemobility com Q6 Edge ll SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the power chair to identify warnings mandatory actions and prohibited actions It is very important for you to read and understand them completely Read and follow the information in the owner s manual Maximum seating weight Do not allow unsupervised children to play near the power chair while the batteries are charging Keep your hands away from the tyres when driving Be a
8. Why do my new batteries seem weak Deep cycle batteries employ a much different chemical technology than that used in car batteries nickel cadmium nicads or in other common battery types Deep cycle batteries are specifically designed to provide power drain down their charge and then accept a relatively quick recharge AGM and Gel Cell batteries should be charged as often as possible They do not have a memory like nickel cadmium batteries We work closely with our battery manufacturer to provide a battery that best suits your power chair s specific demands Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge During shipping the batteries encounter temperature extremes that may influence initial performance Heat robs the charge from the battery and cold slows the power available and extends the time needed to recharge the battery just as with a car battery It might take a few days for the temperature of the battery to stabilise and adjust to its new ambient temperature More importantly it will take a few charging cycles a partial drain then a full recharge to establish the critical chemical balance that is essential to the battery s peak performance and long life It will be well worth it to take the time to break in your battery properly Q6 Edge www pridemobility com 33 BATTERIES AND CHARGING How can I ensure maximum battery life A fully charged deep cycle battery
9. attendant can be defined as a family member or care professional specially trained in assisting a power chair user in various daily living activities As you begin using your power chair during daily activities you will probably encounter situations in which you will need some practice Simply take your time and you will soon be in full and confident control as you manoeu vre through doorways on and off of lifts up and down ramps and over moderate terrain Below are some precautions tips and other safety considerations that will help you become accustomed to oper ating your power chair safely Modifications Pride has designed and engineered your power chair to provide maximum mobility and utility A wide range of accessories is available from your Quantum Rehab Dealer to further customise your power chair to better suit your needs and or preferences However under no circumstances should you modify add remove or disable any fea ture part or function of your power chair ff N WARNING Do not modify your power chair in any way not authorised by Pride Do not use accessories if they have not been tested or approved for Pride products Pre Ride Safety Check Get to know the feel of your power chair and its capabilities Pride recommends that you perform a safety check before each use to make sure your power chair operates smoothly and safely Perform the following inspections prior to using your power chair B Check for proper
10. foot platform angle 1 Flip up the foot platform and locate the screw See figure 20 2 Turn the screw to raise or lower the front of the foot platform PLATFORM BRACKET Figure 20 Foot Platform Adjustment 28 www pridemobility com Q6 Edge V COMFORT ADJUSTMENTS Power Elevating Seat Optional If your power chair is equipped with a power elevating seat you can change the seat height either through the controller or through a toggle switch mounted to one of the armrests To change the seat height through toggle switch 1 Press forward on the toggle switch to raise the seat See figure 21 2 Pull back on the toggle switch to lower the seat WARNING Do not allow the motor to N run more than a few seconds after the 7 mechanism reaches the top or bottom 6 limit NOTE For more information on operating the power elevating seat through the controller contact your Quantum Rehab Dealer WARNING The power elevating seat option is intended for use on a level surface only Never raise the seat from its lowest position on an inclined surface Failure to heed this warning can result in the power chair tipping over Figure 21 Power Elevating Seat Toggle Switch WARNING Never raise the seat from its lowest position when operating N your power chair on bumpy or uneven surfaces Failure to heed this warning E can result in the power chair tipping over WA
11. s begin to close push on the rubber door edge or allow the rubber door edge to contact the power chair and the door will reopen Use that handbags packages or power chair accessories do not become caught in lift doors Lift Systems Elevation Products If you will be transporting your power chair during travel you may find it necessary to use a vehicle mounted lift system or elevation product to aid in transportation Pride recommends that you closely review the warnings instructions specifications and safety information set forth by the manufacturer of the lift elevation product before using that product WARNING Not all lift systems elevation products are rated for use with an occupied mobility device Pride recommends that you do not remain seated in your power chair when it is being used in connection with any type of lift system elevation product unless y W That product is rated for occupied use by the manufacturer A N BH You are able to occupy your mobility device in strict conformity with the warnings A N instructions specifications and safety guidelines set forth by the manufacturer WARNING Always turn off the power to the controller when you are being transferred via an elevation product Failure to do so may result in accidental joystick contact resulting in unintended movement and personal injury or product damage Motor Vehicle Transport Pride recommends that you do not remain seated in your power chair w
12. the battery charger is pro vided by one or more wiring harnesses See figure 7 Controller Harness Connector The controller harness connector is where the controller plugs into the power base Each controller uses a different type of harness Regardless of which type of controller is used the harness must be secured to the seat assembly and not allowed to drag on the floor Motor Connectors This is where the controller connects to the motors Battery Connector This is where the controller connects to the batteries Controller Power Module This enables the controller to communicate with the batteries and the motors 18 www pridemobility com Q6 Edge lll YOUR POWER CHAIR Main Circuit Breaker located on the rear main frame The main circuit breaker is a safety feature built into your power chair When the batteries and the motors are heavily strained e g from excessive loads the main circuit breaker trips to prevent damage to the motors and the electronics If the circuit trips allow your power chair to rest for approximately one minute Next push in the circuit breaker button turn on the controller and con tinue normal operation If the main circuit breaker continues to trip repeatedly contact your Quantum Rehab Dealer CONTROLLER POWER MODULE CONTROLLER CONNECTOR TO BATTERY CONNECTORS TO MOTOR MAIN CIRCUIT CONNECTOR BREAKER TO MOTOR QUICK RELEASE CONNECTOR BATTERY CONNECTORS ND 0 S e TIS
13. Ay Figure 7 Q6 Edge Electrical Components Q6 Edge www pridemobility com 19 lll YOUR POWER CHAIR Manual Freewheel Levers For your convenience your power chair is equipped with a manual freewheel lever mounted on each motor The levers allow you to disengage the drive motors and manoeuvre the chair manually WARNING Do not use the power chair while the drive motors are disengaged Do not disengage the drive motors when the power chair is on an incline as the unit could roll on its own Only engage the freewheel mode when on a level surface TAN A N WARNING It is important to remember that when your power chair is in freewheel 7 N mode the braking system is disengaged L To operate the manual freewheel levers 1 Push down both manual freewheel levers for freewheel mode drive motor disengaged See figure 8 2 Pull up both manual freewheel levers for drive mode drive motor engaged See figure 9 NOTE You must turn off the power before disengaging the drive motor otherwise you may get an error code on the controller To clear this code turn off the controller and place the power chair in drive mode Then turn on the controller The error message should be cleared If it is not contact your Quantum Rehab Dealer NOTE The power chair will be significantly easier to push with the power off WARNING Avoid applying excessive force to the manual freewheel levers 4 N WARNING Do not use your foot to o
14. EMI RFI This product has been tested and passed at an immunity level of 20 V m Indicates electrical shock hazard Locked and in drive mode Place unit on level ground and stand to one side when changing from drive mode to freewheel mode or freewheel mode to drive mode Unlocked and in freewheel mode Battery Set Configuration Positive Red Terminal Post Negative Black Terminal Post 1 F 125A gt 25 Connect Red wires to Red Positive Terminal Posts Connect Black wires to Black Negative Terminal Posts NOTE Motor speeds up to 8 km h 5 mph require 50A ACB 24V 5 50 6 70 Battery posts terminals and related accessories contain lead lead compounds Wear goggles and gloves when handling batteries and wash hands after handling Battery charger for indoor use only Wire access point For service use only www pridemobility com 7 11 SAFETY Disposal and recycling Contact your Quantum Rehab Dealer for information on proper disposal and recycling of your Pride product and its packaging Class Equipment Manufactured in XXXXXX Manufacturer Pride Mobility Products Corp www pridemobilty com Maximum Speed X XX km h X X mph Maximum User Weight XXX kg XXX Ibs I E Unit Weight Unloaded XXX XX kg XXX Ibs Power chair information label Maximum Angle Capacity XX X XX M
15. IN A WARNING When cornering sharply reduce your speed and maintain a stable centre of gravity J This greatly reduces the possibility of a tip or fall Q6 Edge www pridemobility com 11 11 SAFETY Public Streets and Roadways WARNING You should not operate your power chair on public streets and roadways Be aware MaN that it may be difficult for traffic to see you when you are seated on your power chair Obey all 7 local pedestrian traffic rules Wait until your path is clear of traffic and then proceed with 7 extreme caution Outdoor Driving Surfaces Your power chair is designed to provide optimum stability under normal driving conditions dry level surfaces composed of concrete blacktop or tarmac However Pride recognises that there will be times when you will encounter other surface types For this reason your power chair is designed to perform admirably on packed soil grass and gravel Feel free to use your power chair safely on lawns and in park areas Avoid driving on uneven terrain and or soft surfaces Avoid tall grass that can entangle the running gear Avoid loosely packed gravel and sand Do not use your power chair in fresh or salt water Do not use your power chair at the edge of a stream lake or ocean If you feel unsure about a driving surface avoid that surface Inclement Weather Precautions Exposure of your power chair to inclement weather conditions should be avoided whenever pos
16. Q6 Edge OWNER S MANUAL Pride Mobility Products Ltd www pridemobility com 32 Wedgwood Road Bicester Oxon OX26 4UL SAFETY GUIDELINES WARNING A Quantum Rehab Dealer or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual amp The symbols below used throughout this owner s manual and on the power chair to identify warnings and important information It is very important for you to read them and understand them completely procedures cause either personal injury component damage malfunction On the product J WARNING Indicates a potentially hazardous condition situation Failure to follow designated this icon is represented as a black symbol on a yellow triangle with a black border MANDATORY These actions should be performed as specified Failure to perform mandatory actions can cause personal injury and or equipment damage On the product this icon is represented as a white symbol on a blue dot with a white border PROHIBITED These actions are prohibited These actions should not be performed at any time or in any circumstances Performing a prohibited action can cause personal injury and or equipment damage On the product this icon is represented as a black symbol with a red circle and red slash Quick Reference Information Quantum Rehab Dealer Address Phone Number Purchase Dat
17. RNING Never raise the power elevating seat while your power chair is in the freewheel mode WARNING Always fasten the positioning belt when operating the power elevating seat NOTE The power elevating seat option is equipped with a system that reduces the speed of the power chair to one quarter when the seat is elevated Always check to be sure this system is operating properly before using your power chair Q6 Edge www pridemobility com 29 V COMFORT ADJUSTMENTS Positioning Belt Your power chair may be equipped with a positioning belt that can be adjusted for operator comfort See fig ure 22 The positioning belt is designed to support the operator so that he she does not slide down or forward in the seat The positioning belt is not designed for use as a restraining device WARNING The positioning belt is not designed for use as a seat belt in a y N motor vehicle Nor is your power chair jf suitable for use as a seat in any vehicle Anyone traveling in a vehicle should be properly belted into seats approved by the vehicle manufacturer To install the positioning belt 1 Remove the rearmost screw that holds the seat hinge to the seat base on both the left and right seat hinges 2 Insert the screw through the supplied washer through the positioning belt and into the seat base for each side of the power chair seat 3 Tighten both screws To adjust the positioning belt for operator comfort 1 Once sea
18. RNING When changing a tyre remove only the five lug nuts then remove the wheel If any further disassembly is required deflate the tyre completely or it may explode Q6 Edge www pridemobility com 37 Vil CARE AND MAINTENANCE REAR WHEEL HALF LUG NUTS WARNING Completely deflate the tyre before attempting repair Figure 24 Q6 Edge Drive Wheel Figure 25 Q6 Edge Drive Wheel Disassembled Follow these easy steps for a quick and safe repair for both pneumatic and solid tyres Turn off the power to the controller Set the power chair up on blocks If you are changing a pneumatic tyre completely deflate it before removing the wheel Remove the 5 lug nuts from the wheel hub See figure 24 Pull the wheel off of the hub Remove the screws and separate the front and rear wheel See figure 25 Remove the old tube from the pneumatic tyre and replace it with a new tube or replace the entire assembly if it is a solid tyre 8 Screw together the two wheel halves 9 Slide the wheel back onto the hub 10 Reinstall the five 5 lug nuts onto the wheel hub and tighten 11 Inflate the pneumatic tyre to the psi bar kPa air pressure rating indicated on each tyre 12 Remove the power chair from the blocks SLOVY SN Battery Replacement A battery wiring diagram is printed on a decal located on the front cover See the specification table for correct battery specifications MANDATORY Battery posts terminals and related acces
19. a air pressure rating indicated on the JAN tyre for pneumatic tyres Do not underinflate or overinflate your tyres Low pressure may result in y loss of control and overinflated tyres may burst Overinflating tyres can cause them to explode WARNING Do not use a high pressure hose to inflate your tyres E Use a rubber conditioner on the tyre sidewalls to help preserve them N N WARNING Never use a rubber conditioner on the tread area of the tyres doing so may make the tyres slippery and cause your power chair to skid wheel bearings are prelubricated and sealed They require no subsequent lubrication Q6 Edge www pridemobility com 35 Vil CARE AND MAINTENANCE M The body shroud has been sprayed with a clear sealant coating You can apply a light coat of car wax to help it retain its high gloss appearance B Check all electrical connections Make sure they are tight and are not corroded Batteries must sit flat within the battery tray with the battery terminals facing rearward Refer to the battery wiring label for the correct wiring layout WARNING Even though the power chair has passed the necessary testing requirements for ingress of liquids you should keep electrical connections away CY from sources of dampness including direct exposure to water or bodily fluids and gt M incontinence Check electrical components frequently for signs of corrosion and EE v replace as necessary Dail
20. age of 120 VAC alternating current and converts it to 24 VDC direct current The power chair batteries use direct current to run your power chair When the battery voltage is low the charger works harder to charge the battery As the battery voltage approaches full charge the charger does not work as hard to complete the charging cycle When the battery is fully charged the amperage from the charger is nearly at zero This is how the charger maintains a charge but does not overcharge the battery Can I use a different battery charger You should use the charger supplied with the power chair It is the safest most efficient tool to charge the batteries We do not recommend using other types of chargers e g an automotive battery charger NOTE Your power chair s charger will not operate after the batteries have been discharged to nearly zero voltage If this happens call your Quantum Rehab Dealer for assistance How often must I charge the batteries Many factors come into play when deciding how often to charge the batteries You may use your power chair all day on a daily basis or you may not use it for weeks at a time 32 www pridemobility com Q6 Edge BATTERIES AND CHARGING B Daily Use If you use your power chair on a daily basis charge the batteries as soon as you are finished using your power chair Your power chair will be ready each morning to give you a full day s service It is recommended that you charge the batter
21. aximum Allowable Incline X Grn oss 609661 s p Indicates power chair securement points Indicates that power chair with similarly labeled seating system conforms to ANSI RESNA WC Vol 4 Section 19 for transport of an occupied power chair in a motor 22 vehicle 8 www pridemobility com Q6 Edge ll SAFETY GENERAL GUIDELINES Y MANDATORY Do not operate your new power chair for the first time without completely reading Uy and understanding this owner s manual Your power chair is a state of the art life enhancement device designed to increase mobility Pride provides an extensive variety of products to best fit the individual needs of the power chair user Please be aware that the final selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user who is capable of making such a decision and his her healthcare professional i e medical doctor physical therapist etc The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair to the user and has assisted the prescribing healthcare professional and or the Quantum Rehab Dealer in the instruction process for the use of the product There are certain situations including some medical conditions where the power chair user will need to practice operating the power chair in the presence of a trained attendant A trained
22. do not attempt to negotiate inclines with the seat in a reclined position Do not attempt to negotiate obstacles with the seat in a reclined position unless an attendant is present to help stabilise the chair Failure to heed may result the power chair tipping over WARNING Even though your power chair is capable of climbing slopes greater than those illustrated in figure 1 do not under any circumstances exceed the incline guidelines or any other specifications presented in this manual Doing so could cause instability in your power chair Pride recommends that the maximum slope of an incline you attempt to safely ascend or descend on your power chair does not exceed 10 5 6 See figure 1 JN WARNING Any attempt to climb or descend a slope steeper than 10 5 6 may put your power E e 7 7 N 7 N chair in an unstable position and cause it to tip Mee e Figure 1 Maximum Recommended Safe Slope Ascending and Descending Freewheel Mode Your power chair is equipped with two manual freewheel levers to allow for manual manoeuvreability by a trained attendant For more information about how to place your power chair into and out of freewheel mode see III Your Power Chair WARNING Do not use your power chair in freewheel mode without an attendant present A N WARNING Do not attempt to personally place your power chair in freewheel mode J while seated it Ask an attendant for assista
23. e NOTE This owner s manual is compiled from the latest specifications and product information available at the time of publication We reserve the right to make changes as they become necessary Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased The latest current version of this manual is available on our website CES Copyright 2011 Pride Mobility Products Ltd INFMANU4167 Rev A August 2011 CONTENTS I INTRODUCTION fn along dese Gab Na d due 4 Il SAFETY e 5 IL YOUR POWER CHAIR n RR ER ea ten nel ve ei qus 17 IV ASSEMBLY our edo oin atn delen eit Fd eet aud a ed Mea ed 21 V COMFORT ADJUSTMENTS seen ertet etre 24 VI BATTERIES AND CHARGING eee 31 VII CARE AND MAINTENANCE essere eerte 35 VILWARRANTJY once Eodem pe hn i dde anise ag oa kan bein dno deb daca o Tob Ud 4l SSSSSSSSS S S S S S S S S S S S SS _ __________qqqqqqqqqqqqq___aam Q6 Edge www pridemobility com 3 1 INTRODUCTION SAFETY WELCOME to Quantum Rehab a division of Pride Mobility Products Pride The power chair you have pur chased combines state of the art components with safety comfort and styling in mind We are confident that these design features will provide you with the conveniences you expect during your daily activities Once you understand how
24. e armrest 4 Tighten the locking nut to lock the adjusting screw into place Armrest Height Adjustment To change the armrest height 1 Loosen the two setscrews located on the armrest receiver See figure 18 2 Raise or lower the armrest to the desired height 3 Tighten the setscrews to secure the armrest LOCKING NUT ARMREST ANGLE ADJUSTING SCREW ARMREST HEIGHT ADJUSTING SETSCREWS SEATBACK ANGLE ADJUSTING SCREW Figure 18 Seatback Armrest Adjustment 26 www pridemobility com Q6 Edge V COMFORT ADJUSTMENTS Controller Position You can move the controller in toward or out away from the armrest or change the position of the control ler for either left hand or right hand use JN WARNING Do not place the controller harness so that it can be pinched in the A j seat frame or the power base frame CONTROLLER BRACKET To extend the controller 1 Flip up the armrest so it is perpendicular to the cd floor 2 Loosen the setscrew on the controller bracket See figure 19 3 Slide the controller into or out of the armrest to the desired position 4 Tighten the setscrew to secure the controller To change the controller position 1 Turn off the power to the controller 2 Unplug the controller connector s from the power base Remove any wire ties securing the controller har ness to the armrest Flip up the armrest so it is perpendicular to the floor Loosen t
25. e controller or controller bracket for weight bearing purposes such as transfers Such use may cause damage to these components resulting in a fall from the power chair and personal injury WARNING Avoid putting all of your weight on the front riggings Such use may cause the power chair to tip Prescription Drugs Physical Limitations Users must exercise care and common sense when operating a power chair This includes awareness of safety issues when taking prescribed or over the counter drugs or when the user has specific physical limitations JN WARNING Consult your physician if you are taking prescribed or over the counter medication or if you have certain physical limitations Some medications and limitations may impair your ability to operate your power chair a safe manner Q6 Edge www pridemobility com 15 11 SAFETY User Positioning Pride recommends that all users be seated in an upright position with their pelvis positioned as far rearward as possible in the power chair seat All users need to discuss pelvic positioning with their Quantum Rehab Dealer therapist s or healthcare professional to determine appropriate pelvic position when seated on the power chair based on the user s individual medical needs Alcohol Smoking The power chair user must exercise care and common sense when operating his her power chair This includes awareness of safety issues while under the influence of alcohol or while s
26. ed adjustment set to the slowest speed setting to ensure a safely controlled descent Avoid sudden stops and starts When climbing an incline try to keep your power chair moving If you must stop start up again slowly and then accelerate cautiously When driving down an incline set your power chair to the slowest speed setting and drive in the forward direction only If your power chair starts to move down the incline faster than you anticipated or desired allow it to come to a complete stop by releasing the joystick then push the joystick forward slightly to ensure a safely controlled descent WARNING When on any sort of an incline or decline never place the power chair in amp E freewheel mode especially while seated on it or standing next to it WARNING When climbing an incline do not zigzag or drive at an angle up the face of the incline Drive your power chair straight up the incline This greatly reduces the possibility of a tip or a fall Always exercise extreme caution when negotiating an A incline IN N WARNING You should not travel up or down a potentially hazardous incline i e 4 areas covered with snow ice cut grass or wet leaves WARNING Never travel down an incline rearward Doing so may cause the power chair to tip Always exercise extreme caution when negotiating an incline 10 www pridemobility com Q6 Edge ll SAFETY WARNING If your power chair is equipped with a reclining seatback
27. f your power chair is equipped with a transit securement system it is equipped with manufacturer installed front and rear securement brackets and positioning belt anchoring brackets See figure 15 Refer to the supplement provided with your power chair for information on how to use the transit securement system SEAT PLATE INTERFACE BRACKET ACTUATOR Figure 14 Power Elevating Seat Actuator c MEC Bow N S T ic 25 TO POWER BASE _ s Figure 13 Controller Harness Routing on a Contour Seat ANCHORING BRACKET LOCATIONS 1 OF 2 SHOWN SECUREMENT BRACKETS 3 OF 4 SHOWN Figure 15 Transit System Securement Brackets Q6 Edge www pridemobility com 23 V COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair s operation you may find the need to make some adjustments to increase your comfort such as seat height and angle armrest width armrest angle and height foot platform height depth and angle and controller position NOTE If your power chair is equipped with a Specialty Seat Synergy Seat or TRU Balance Power Positioning System refer to the seat adjustment information contained in separate manuals If your power chair is equipped with a contoured seating system refer to the following information WARNING The centre of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users Yo
28. h as walkie talkies radio stations TV stations amateur radio HAM transmitters wireless com puter links microwave signals paging transmitters and medium range mobile transceivers used by emergency vehicles In some cases these waves can cause unintended movement or damage to the control system Every electrically powered mobility vehicle has an immunity or resistance to EMI The higher the immunity level the greater the protection against EMI This product has been tested and has passed at an immunity level of 20 V m WARNING Be aware that cell phones two way radios laptops and other types of radio transmitters may cause unintended movement of your electrically powered mobility vehicle due to EMI Exercise caution when using any of these items while operating your mobility vehicle and avoid coming into close proximity of radio and TV stations WARNING The addition of accessories or components to the electrically powered mobility vehicle can increase the susceptibility of the vehicle to EMI Do not modify your power chair A N any way not authorised by Pride WARNING The electrically powered mobility vehicle itself can disturb the performance of other electrical devices located nearby such as alarm systems NOTE For further information on EMI RFI go to the Resource Center on www pridemobility com If unin tended motion or brake release occurs turn your power chair off as soon as it is safe to do so Contact your au
29. hat the connections are secure N J 8 Connect the battery harness to the new rear battery according to the battery wiring diagram See figure 26 9 Install the new batteries and connect the quick release battery connectors 10 Reinstall the front cover and foot platform 11 Charge the batteries See VI Batteries and Charging BATTERY WIRING DIAGRAM LABEL FRONT BATTERY Figure 26 Battery Installation Q6 Edge www pridemobility com 39 Vil CARE AND MAINTENANCE When to See Your Quantum Rehab Dealer for Service The following symptoms could indicate a serious problem with your power chair If necessary contact your Quantum Rehab Dealer When calling have the model number serial number nature of the problem and the error code if available Motor noise Frayed harnesses Cracked or broken connectors Uneven wear on any of the tyres Jerky motion Pulling to one side Bent or broken wheel assemblies Does not power up Powers up but does not move Loose seat or seating components Corrective Maintenance If the battery condition meter does not light up when you turn on the power Check the harness connections Make sure they are tight B Check the circuit breaker Reset it if necessary B Check the battery connections If the above conditions prove normal you can load test the batteries with a battery load tester These testers are available at automotive parts stores
30. he setscrew on the controller bracket Slide the controller out of the armrest Loosen the setscrew in the other armrest Place the controller in the other armrest Tighten the setscrews in both armrests 0 Route the controller harness to the back of the power base and plug in the controller 11 Secure the controller harness to the armrest with wire ties See figure 13 Figure 19 Underside of Armrest E Te NOTE If your power chair is equipped with a Spe cialty Seat Synergy Seat or TRU Balance Power Positioning System refer to the information provided in supplemental manuals provided with your seating system Q6 Edge www pridemobility com 27 V COMFORT ADJUSTMENTS Foot Platform Height Adjustment The foot platform height is easily adjusted to several different heights To raise or lower the foot platform 1 Remove the hardware from the foot platform bracket See figure 20 2 Raise or lower the foot platform to the desired height 3 Reinstall the hardware into the foot platform bracket and tighten Foot Platform Depth Adjustment You can adjust the depth of the foot platform To adjust the foot platform depth 1 Remove the hardware from the foot platform bracket See figure 20 2 Move the foot platform in or out to the desired depth 3 Reinstall the hardware into the foot platform bracket and tighten Foot Platform Angle Adjustment You can adjust the angle of the foot platform To adjust the
31. hile traveling in a motor vehicle The power chair should be stowed in the boot of a car or in the back of a truck or van with batteries removed and or properly secured In addition all removable power chair parts including the armrests seat front riggings con troller and shrouds should be removed and or properly secured during motor vehicle transport If your power chair is equipped with a transit securement system refer to IV Assembly and the supplement provided with your power chair for additional information regarding power chair transport in a motor vehicle Q6 Edge www pridemobility com 13 11 SAFETY WARNING Pride does not recommend using the power chair as a seat in a motor vehicle The power chair user should transfer into the vehicle seat and use the vehicle installed belt restraint system if and whenever feasible If your power chair is equipped with a manufacturer installed transit securement system please refer to the supplemental safety information provided with your power chair I WARNING Ensure power chairs equipped with a transit securement system are properly SIN secured to the motor vehicle during transport Power chairs that are not properly secured can become a hazard to the user and to other vehicle passengers in the event of a crash sudden stopping or swerving as the power chair could tip or slide out of place WARNING Always be sure your power chair and its batteries are properly secured when it is
32. ies 8 to 14 hours after daily use B Infrequent Use If you use your power chair infrequently once a week or less you should charge the batteries at least once per week for 12 to 14 hours NOTE Keep your batteries fully charged and avoid deeply discharging your batteries Refer to the manual supplied with the battery charger for charging instructions How can I get maximum range or distance per charge Rarely do you have an ideal driving situation such as smooth flat hard terrain with no wind hills or curves More often you are presented with hills pavement cracks uneven and loosely packed surfaces curves and wind All of these factors will affect the distance or running time per battery charge Below are a few suggestions for obtain ing the maximum range per charge Always charge the batteries fully prior to your trip Plan your trip in advance to avoid inclines if possible B Limit baggage weight to essential items Try to maintain an even speed and avoid stop and go driving What type of batteries should I use We recommend deep cycle batteries that are sealed and maintenance free Both AGM and Gel Cell are deep cycle batteries that are similar in performance Refer to the specifications table for more information regarding the batteries used with your power chair bX WARNING Corrosive chemicals contained in batteries Use only AGM or Gel Cell N batteries to reduce the risk of leakage or explosive conditions
33. moking WARNING Do not operate your power chair while you are under the influence of alcohol as this may impair your ability to operate your power chair in a safe manner WARNING Pride strongly recommends that you do not smoke cigarettes while seated your N power chair although the power chair has passed the necessary testing requirements for cigarette smoking You must adhere to the following safety guidelines if you decide to smoke 4 cigarettes while seated in your power chair not leave lit cigarettes unattended W Keep ashtrays a safe distance from the seat cushions WB Always make sure cigarettes are completely extinguished before disposal Flammability Precautions WARNING Even though the plastics on your power chair have passed the applicable flammability standards Pride recommends that you do not expose your power chair to open flames JIN WARNING Replace worn or damaged upholstery immediately to reduce the risk of fire hazard WARNING Be aware that washing of upholstered items may reduce the resistance to flammability of the fabric Electromagnetic and Radio Frequency Interference EMI RFI 7 WARNING Laboratory tests have shown that electromagnetic and radio frequency waves can J y have an adverse effect on the performance of electrically powered mobility vehicles Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones mobile two way radios suc
34. nce if necessary WARNING Pride recommends that you do not disconnect the batteries when the power chair is in freewheel mode as this may interfere with the function of the controller WARNING Do not place your power chair in freewheel mode while on an incline or decline This could cause the chair to roll uncontrollably on its own Braking Information Your power chair is equipped with two powerful brake systems M Regenerative uses electricity to rapidly slow the vehicle when the joystick returns to the centre stop position Disc Park Brake activates mechanically after regenerative braking slows the vehicle to near stop or when power is removed from the system for any reason Cornering Information While your power chair is equipped with front and rear castor wheels excessively high cornering speeds can still create the possibility of tipping Factors which affect the possibility of tipping include but are not limited to corner ing speed steering angle how sharply you are turning uneven road surfaces inclined road surfaces riding from an area of low traction to an area of high traction such as passing from a grassy area to a paved area especially at high speed while turning and abrupt directional changes High cornering speeds are not recommended If you feel that you may tip over in a corner reduce your speed and steering angle 1 lessen the sharpness of the turn to prevent your power chair from tipping
35. ng 4 the armrests seat front riggings controller and shrouds Pride recommends use of only solid a 4 non removable frame components to lift or move your power chair 14 www pridemobility com Q6 Edge ll SAFETY Preventing Unintended Movement turn off the power This will prevent unexpected motion from inadvertent joystick contact This will also eliminate the possibility of unintended chair movement from electromagnetic EM sources WARNING If you anticipate being seated stationary position for an extended period of time Reaching and Bending Never reach lean or bend while driving your power chair If it is absolutely necessary to reach lean or bend while seated on your power chair it is important to maintain a stable centre of gravity and keep the power chair from tipping Pride recommends that the power chair user determine his her personal limitations and practice bending and reaching in the presence of a qualified healthcare professional WARNING Do not bend lean or reach for objects if you have to pick them up from f N the floor by reaching down between your knees or if you have to reach over the back A N of the seat Movements such as these may change your centre of gravity and the weight distribution of the power chair possibly causing your power chair to tip WARNING Keep your hands away from the tyres when driving Be aware that loose fitting clothing can become caught in drive tyre
36. ng in a vehicle should A be properly belted into seats approved by the vehicle manufacturer If your power chair is equipped with manufacturer installed transit securement system please refer to the supplemental safety information provided with your power chair Batteries In addition to following the warnings below be sure to comply with all other battery handling information For more information about your power chair s batteries see VI Batteries and Charging Lead IN WARNING Always protect the batteries from freezing and never charge a frozen battery Charging a frozen battery may result in damage to the battery MANDATORY Battery posts terminals and related accessories contain lead and lead compounds Wear goggles and gloves when handling batteries and wash hands after handling WARNING Power chair batteries are heavy See specifications table If you are unable to lift that much weight be sure to get help Use proper lifting techniques and avoid lifting beyond your capacity WARNING Connect your battery harnesses in the proper manner RED cables must be connected to positive battery terminals posts BLACK cables must be connected to negative battery terminals posts Protective caps should be installed over all battery terminals REPLACE cables immediately if damaged Removable Parts y WARNING Do not attempt to lift or move a power chair by any of its removable parts includi
37. o optimise your MANDATORY Battery posts terminals and related accessories contain lead and lead compounds Wear goggles and gloves when handling batteries and wash hands after handling WARNING Contact your Quantum Rehab Dealer if you have any questions regarding the batteries in your power chair PROHIBITED Always use two batteries of the exact same type chemistry and amp hour Ah capacity Refer to specifications table in this manual and in the manual supplied with the battery charger for recommended type and capacities power chair s performance by charging the batteries safely quickly and easily SS JAN O Be Cu NP gt Q6 Edge PROHIBITED Removal of grounding prong can create electrical hazard If necessary properly install an approved 3 pronged adapter to an electrical outlet having 2 pronged plug access PROHIBITED Never use an extension lead to plug in your battery charger Plug the charger directly into a properly wired standard electrical outlet PROHIBITED Do not allow unsupervised children to play near the power chair while the batteries are charging Pride recommends that you do not charge the batteries while the power chair is occupied MANDATORY Read the battery charging instructions in this manual and in the manual supplied with the battery charger before charging the batteries WARNING Explosive gases may be generated while charging the batteries Keep
38. perate the manual freewheel levers Do not stand on the manual freewheel levers Applying excessive force to the manual freewheel levers may result in 4 y damage to the freewheel levers motors and brakes WARNING Do not use the freewheel lever handles as tie down points to secure this product LEST I P y INNA AV AP 22 lh gt ND M MANUAL FREEWHEEL LEVER Figure 8 Freewheel Mode Drive Disengaged Figure 9 Drive Mode Drive Engaged ODLAAAOOOEA AAA WV e C 0 4 LDLOAAA L LOL LLALAO ALLLLOOLA OeAL LOULAAA O A OAA LCOgULOLLLLO LOLL L LLLLL JPbykpLALELAL I AXxXkAzAA A A XA 20 www pridemobility com Q6 Edge IV ASSEMBLY INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation It may also require disassembly to make some comfort adjustments Figure 10 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified carer before using the product or making comfort adjustments NOTE Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be replaced with a new nut Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert resulting in a less secure fit Replacement nylon insert lock nuts are available at local hardware stores or through your Quantum Rehab Dealer
39. power chair should be stored in a dry place free from temperature extremes When storing disconnect the batteries from the power chair See VI Batteries and Charging 5 A N WARNING If you fail to store the unit properly the frame can rust and the electronics can be damaged Any corroded electronic connection should be replaced Batteries that are regularly and deeply discharged infrequently charged stored in extreme temperatures or stored without a full charge may be permanently damaged causing unreliable performance and limited service life It is recommended that you charge the batteries periodically throughout periods of prolonged storage to ensure proper performance You may wish to place several boards under the frame of your power chair to raise it off of the ground during periods of prolonged storage This takes the weight off the tyres and reduces the possibility of flat spots develop ing on the areas of the tyres contacting the ground Disposal of Your Power Chair Your power chair must be disposed of according to applicable local and national statutory regulations Contact your local waste disposal agency or Quantum Rehab Dealer for information on proper disposal of power chair packaging metal frame components plastic components electronics batteries neoprene silicone and polyurethane materials Cleaning and Disinfection Use a damp cloth and mild non abrasive cleanser to clean the plastic and metal parts of
40. r labour and service Please contact your Quantum Rehab Dealer for information about these services and for any applicable charges Q6 Edge www pridemobility com 41 42 www pridemobility com Q6 Edge Quality Control Q6 Edge Inclusion of all Parts Joystick Serial Number Controller Serial Number Left Motor Serial Number Right Motor Serial Number Fitand Finish Performance Pride keeps a more detailed report on file at the factory Date Inspected Inspector NFMANU4167 Product Serial 4
41. rate 3 Check the joystick operation and the brakes before using your power chair again 4 If any inconsistencies are found take your power chair to a Quantum Rehab Dealer Power chairs that are frequently exposed to sources of water such as incontinence should be inspected often for corrosion and electronic components may need to be replaced frequently Temperature Some of the parts of your power chair are susceptible to extreme changes in temperature Always keep your power chair between the temperatures of 8 C 18 F and 50 122 F E In extremely cold temperatures the batteries may freeze The specific temperature at which they freeze depends on a number of factors such as battery charge usage and composition of the batteries e g AGM or Gel Cell B Temperatures above 50 C 122 F may cause your power chair to operate at a reduced speed This reduced speed is a safety feature built into the controller that helps prevent damage to the motor and other electrical components General Guidelines Avoid knocking or bumping the controller especially the joystick Avoid prolonged exposure of your power chair to extreme conditions such as heat cold or moisture Keep the controller clean Check all connectors to ensure that they are all tight and secured properly Make sure pneumatic tyres are inflated to the psi bar kPa air pressure rating indicated on the tyre WARNING Make sure your tyres are inflated to the psi bar kP
42. route the harness to the back of the power base See figures 12 or 13 MANDATORY Prevent controller harness damage Avoid routing the controller harness on the outside of the armrest pad Route the harness IN under the armrest or toward the inside N of the armrest pad Use correct tie 0 down points for controller harness to prevent the harness from getting caught in the drive tyres pinched in the seat frame or damaged when passing through doorways 5 Plug the controller connector into the rear of the power base See figure 7 6 Secure the controller harness to the armrest receiver with wire ties See figure 13 SEAT LATCH SAFETY REAR FRONT EXTRUSION EXTRUSION TRAPEZE BARS ARS amp Figure 12 Controller Harness Routing on a Synergy Seat 22 www pridemobility com Q6 Edge IV ASSEMBLY Power Elevating Seat Option Your power chair may be equipped with a power ele vating seat option While the seat itself may be any one of the styles offered for this model the way the seat base attaches to the power base is different To install the power elevating seat Place the seat plate interface bracket onto the actu ator See figure 14 2 Insert the supplied hardware into the actuator and tighten the hardware 3 Place the seating system onto the seat plate and secure 4 Plug in the power seat toggle switch harness if equipped Transit Securement System Optional I
43. s Transfers Transferring onto and off of your power chair requires a good sense of balance Always have an attendant or healthcare professional present while learning to properly transfer yourself To eliminate the possibility of injury Pride recommends that you or a trained attendant perform the following tasks before attempting a transfer Turn off the power to the controller Ensure your power chair is not in freewheel mode See III Your Power Chair Turn the castor wheels toward the transfer destination to improve power chair stability during transfer Make sure both armrests are flipped up or removed from your power chair Flip up the foot platform or move the leg rests aside this will help to keep your feet from getting caught on the front rigging during the transfer Reduce the distance between your power chair and the object you are transferring onto Figure 4 Ideal Transfer Position WARNING Before transferring position yourself as far back as possible in the power chair seat to prevent the power chair from tipping forward during transfer WARNING Avoid putting all of your weight on the power chair armrests and do not use the armrests for weight bearing purposes such as transfers Such use may cause the power chair N to tip resulting in a fall from the power chair and personal injury A 4 N WARNING The controller and controller bracket are non load bearing items on your power chair Do not use th
44. sible If suddenly caught up in rain snow severe cold or heat while operating your power chair proceed to shelter at the earliest opportunity Thoroughly dry your power chair before storing charging or operating your power chair PROHIBITED Operating in rain snow salt mist spray conditions and on icy slippery surfaces KEN CY can have an adverse effect on the electrical system Maintain and store your power chair in a wy dry and clean condition WARNING Prolonged exposure to hot or cold conditions may affect the temperature of upholstered and non upholstered items on the power chair possibly resulting in skin irritation Exercise caution when using your power chair in extremely hot or cold conditions or when S exposing your power chair to direct sunlight for prolonged periods of time Stationary Obstacles Steps Kerbs etc Proceed with extreme caution when driving near raised surfaces unprotected ledges and or drop offs kerbs porches stairs etc Be sure your power chair is traveling perpendicular to any kerb you may be required to navigate To navigate up over a kerb or stationary obstacle 1 Approach the kerb or obstacle slowly and make sure the power chair is traveling perpendicular to the obstacle See figure 2 2 Increase the forward speed just before the front wheels come in contact with the obstacle 3 Reduce the forward speed only after the rear wheels have cleared the obstacle To navigate do
45. sories contain lead and lead compounds Wear goggles and gloves when handling batteries and wash hands after handling WARNING The batteries in your power chair should only be serviced or replaced by an authorised Quantum Rehab Dealer or a qualified technician WARNING Do not replace batteries when seat is occupied S N WARNING Power chair batteries are heavy See specifications table If you are N unable to lift that much weight be sure to get help Use proper lifting techniques and avoid lifting beyond your capacity WARNING Do not mix old and new batteries Always replace both batteries at the same time f PROHIBITED Keep tools and other metal objects away from the battery terminals N ji Contact with tools can cause electrical shock 38 www pridemobility com Q6 Edge Vil CARE AND MAINTENANCE To replace the batteries 1 Turn off the power to the controller 2 Make sure that the power chair is in drive mode See III Your Power Chair 3 Remove the front cover by squeezing the release handles see figure 26 and lifting the foot platform bracket up and away from the power base 4 Disconnect the quick release battery connectors See figure 7 5 Remove the batteries 6 Disconnect the battery harness from each battery 7 Connect the battery harness to the new front battery according to the battery wiring diagram See figure 26 A V WARNING Make sure you tighten the fasteners so t
46. stment Manual Recline Seatback Adjustment If your power chair is equipped with a reclining seat you can adjust the seatback angle with the seatback release lever The lever is located on the right side of the seat base To adjust the recline angle 1 Pull up on the seatback release lever 2 Lean forward or rearward to the desired position 3 Release the lever Q6 Edge www pridemobility com 25 V COMFORT ADJUSTMENTS Seatback Angle Adjustment If your power chair is equipped with an adjustable seat back you can adjust it to four 4 different angles 90 102 105 or 107 To adjust the seatback angle 1 Remove the adjusting screws from each seat hinge See figure 18 2 Set the seatback at the desired angle 3 Reinstall the adjusting screws to each seat hinge and tighten Armrest Width Adjustment You can change each armrest s width independently of the other NOTE Changing the armrest width may increase the overall width of your power chair To change the armrest width 1 Locate the two armrest knobs on each side of the armrest receiver bracket See figure 18 2 Loosen the knobs 3 Slide the armrests in or out to the desired width 4 Tighten the knobs Armrest Angle Adjustment To change the armrest angle 1 Lift the armrest straight up so that it is perpendicu lar to the floor See figure 18 2 Loosen the locking nut 3 Turn the adjusting screw to raise or lower the front of th
47. ted insert the metal tab on one side of the belt into the plastic housing on the opposite side until you hear a click See figure 22 2 Pull the excess strap attached to the metal tab until it is secure but not so tight as to cause discomfort To release the positioning belt Figure 22 Positioning Belt Adjustment 1 Press the push button mechanism on the plastic housing MANDATORY 4 4 Ne and repair Make sure the positioning belt is properly secured to the power chair and is adjusted for operator comfort before each use MANDATORY Inspect the positioning belt for loose or damaged parts before each use of the power chair If you discover a problem contact your Quantum Rehab Dealer for maintenance 30 www pridemobility com Q6 Edge BATTERIES AND CHARGING VI BATTERIES AND CHARGING The Q6 Edge uses two long lasting 12 volt deep cycle batteries These batteries are sealed and maintenance free Since they are sealed there is no need to check the electrolyte fluid level Deep cycle batteries are designed to handle a longer and deeper discharge Though they are similar in appearance to automotive batteries they are not interchangeable Automotive batteries are not designed to handle a long deep discharge and also are unsafe for use in power chairs iN Ah s The battery charger is essential in providing long life for your power chair batteries It is designed t
48. th operation of your power chair WARNING It is important that the psi bar kPa air pressure rating indicated on the tyre be maintained in pneumatic tyres at all times Do not underinflate or overinflate your tyres Low pressure may result in loss of control and overinflated tyres may burst Failure to maintain the psi bar kPa air pressure rating indicated on the pneumatic tyres at all times may result in tyre j and or wheel failure WARNING Inflate your power chair drive tyres from a regulated air source with an available pressure gauge Inflating your tyres from an unregulated air source could overinflate them resulting in a burst tyre NOTE If the tyre on your power chair lists the psi rating only use the following conversion formulas to find the bar or kPa rating bar psi x 0 06895 kPa psi x 6 89476 Incline Information More and more buildings have ramps with specified degrees of inclination designed for easy and safe access Some ramps may have turning switchbacks 180 degree turns that require you to have good cornering skills on your power chair Proceed with extreme caution as you approach the downgrade of a ramp or other incline W Take wide swings with your power chair s front wheels around any tight corners If you do that the power chair s rear wheels will follow a wide arc not cut the corner short and not bump into or get hung up on any railing corners B When driving down a ramp keep the power chair s spe
49. the power chair and battery charger away from sources of ignition such as flames or sparks and provide adequate ventilation when charging the batteries WARNING You must recharge the power chair batteries with the supplied off board battery charger Do not use an automotive type battery charger WARNING Inspect the battery charger wiring and connectors for damage before each use Contact your authorised Quantum Rehab Dealer if damage is found WARNING Do not attempt to open the battery charger case If the battery charger does not appear to be working correctly contact your authorised Quantum Rehab Dealer WARNING Be aware that the battery charger case may become hot during charging Avoid skin contact and do not place on surfaces that may be affected by heat WARNING If the battery charger is equipped with cooling slots then do not attempt to insert objects through these slots WARNING If your battery charger has not been tested and approved for outdoor use then do not expose it to adverse or extreme weather conditions If the battery charger is exposed to adverse or extreme weather conditions then it must be allowed to adjust to the difference in environmental conditions before use indoors Refer to the manual supplied with the battery charger for more information www pridemobility com BATTERIES AND CHARGING To charge the batteries using the off board charger 1 Position your power chair next to a standard elec
50. thorised Quantum Rehab Dealer to report the incident 16 www pridemobility com Q6 Edge lll YOUR POWER CHAIR THE Q6 EDGE POWER CHAIR Your power chair has two main assemblies the seat assembly and the power base assembly See figure 5 Typically the seat assembly includes the armrests seatback and seat base The power base assembly includes two motor brake assemblies two drive wheels four castor wheels two batteries and wiring harnesses See figures 5 6 and 7 SEATBACK SEAT ASSEMBLY ARMREST 4 e ARMREST S gt JOYSTICK CONTROLLER SEAT BASE CASTOR WHEEL Q Oy Q Os MANUAL FREEWHEEL LEVER DRIVE WHEEL SPRING SHOCK GAS DAMPER LOCATION FRONT RIGGING CASTOR WHEEL FOOT PLATFORM SHOWN Figure 5 The Q6 Edge Power Chair Q6 Edge www pridemobility com 17 lll YOUR POWER CHAIR REAR SHROUD TRAPEZE BARS FRONT COVER p Figure 6 The Q6 Edge Power Base PROHIBITED The spring tension on your power chair was factory set to meet the needs of the demographic majority of users Do not adjust the tension of any spring on your power chair Electrical Components The electrical components consist of the controller assembly the batteries and the motors The batteries motors and controller power module if equipped are located on the power base assembly The controller is located on the seat assembly Connectivity between the controller and the motors batteries and
51. to safely operate and care for your power chair it should give you years of trouble free operation and service Read and follow all instructions warnings and notes in this manual before attempting to operate your power chair for the first time You must also read all instructions warnings and notes contained in any supplemental instruc tional booklets for the controller front riggings and or seating system that accompanied your power chair before initial operation Your safety depends upon you as well as your provider caretaker or healthcare professional in using good judgement If there is any information in this manual which you do not understand or if you require additional assistance for setup or operation please contact your Quantum Rehab Dealer Failure to follow the instructions in this manual and those located on your power chair can lead to personal injury and or damage to the power chair including voiding the warranty PURCHASER S AGREEMENT By accepting delivery of this product you promise that you will not change alter or modify this product or remove or render inoperable or unsafe any guards shields or other safety features of this product fail refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product SHIPPING AND DELIVERY Before using your power chair make sure your delivery is complete as some components may be individually packaged
52. trical outlet 2 Be certain the controller power is turned off and the power chair is in drive mode 3 Plug the off board charger into the off board charger programming socket on the controller See figure 23 4 Plug the off board charger into the electrical outlet NOTE The LED lights on the charger indicate different charger conditions at various times charger power on charging in progress and charging complete Refer to the manual supplied with the charger for a complete explanation of these indicators 5 When the batteries are fully charged unplug the off board charger from the electrical outlet and then from the controller Figure 23 Battery Charging Battery Break in To break in new batteries for maximum efficiency 1 Fully recharge any new battery prior to its initial use This brings the battery up to about 90 of its peak performance level 2 Operate your power chair throughout the house and grounds Move slowly at first and do not travel too far until you become accustomed to the controls and break in the batteries 3 Give the batteries another full charge of 8 to 14 hours and operate your power chair again The batteries will now perform at over 90 of their potential 4 After four or five charging cycles the batteries will top off at 100 charge and last for an extended period Frequently Asked Questions FAQs How does the charger work The battery charger takes the standard electrical outlet volt
53. tyre inflation Maintain but do not exceed the psi bar kPa air pressure rating indicated on each tyre if equipped with pneumatic tyres Check all electrical connections Make sure they are tight and not corroded Check all controller connections to the power base Make sure they are secured properly Check the brakes See VII Care and Maintenance Check battery charge See VI Batteries and Charging NOTE If you discover a problem contact your Quantum Rehab Dealer for assistance Q6 Edge www pridemobility com 9 11 SAFETY Weight Limitations Your power chair is rated for a maximum weight capacity Please refer to the specifications table for this limit Keep in mind that the maximum weight capacity includes the combined weight of the user and any accessories mounted to the power chair 4 m MANDATORY Stay within the specified weight capacity of your power chair Exceeding the weight capacity voids your warranty Pride will not be held responsible for injuries and or ww property damage resulting from failure to observe weight limitations AN A N WARNING Do not carry passengers on your power chair Carrying passengers on your power N chair may affect the centre of gravity resulting in a tip or a fall T Tyre Inflation If your power chair is equipped with pneumatic tyres you should check or have the air pressure checked regularly Proper inflation pressures will prolong the life of your tyres and help ensure the smoo
54. ur Quantum Rehab Dealer has evaluated your power chair and made any necessary adjustments to suit your specific requirements Do not change your seating configuration without first contacting Pride Mobility Products or your Quantum Rehab Dealer NN e WARNING Some power chair components heavy You may need assistance to lift or carry them Please refer to the specifications table for specific component weights before you disassemble the power chair WARNING Remove the occupant from the power chair before making any adjustments You may need the following to make comfort adjustments WI metric standard socket set and ratchet B adjustable spanner WI metric standard hex key set TRAPEZE BARS BI thread lock Seat Height and Seat Angle Adjustment If your power chair is not equipped with a transit securement system you can change the seat height to one of three positions by raising the front and rear tra I peze bars If you raise or lower only one trapeze bar SEAT INTERFACE front or rear you can also change the seat base angle dump MANDATORY If your power chair is equipped with a transit securement m system and any adjustment to the seat height or seat angle is necessary contact your Quantum Rehab Dealer These comfort adjustments can only be made by a Quantum Rehab Dealer HARDWARE To change the seat height 1 Turn off the power to the controller 2 Make sure the power chair is in drive mode
55. ware that loose fitting clothing can become caught in drive tyres Do not use a cell phone walkie talkie laptop or other radio transmitter while operating Avoid exposure to rain snow ice salt or standing water whenever possible 3e Maintain and store in a clean and dry condition Indicates flammable material Do not expose to heat sources such as open flame or sparks Do not transport batteries with flammable or combustible items Q6 Edge www pridemobility com 5 11 SAFETY Keep tools and other metal objects away from battery terminals Contact with tools can cause electric shock Do not connect an extension lead to the AC DC converter or the battery charger Removal of grounding prong can create electrical hazard If necessary properly install an approved 3 pronged adapter to an electrical outlet having 2 pronged plug access Do not mix AGM and Gel Cell batteries Always use batteries of the same type and chemistry AGM Use only AGM or Gel Cell batteries to reduce the risk of leakage or explosive GEL CELL conditions Do not use batteries with different amp hour Ah capacities Do not mix old and new Ah 7 Ah batteries Always replace both batteries at the same time A Do not place your power chair in freewheel mode while on an incline or decline Explosive conditions exist A Corrosive chemicals contained in battery www pridemobility com Q6 Edge 11 SAFETY
56. will provide reliable performance and extended battery life Keep your power chair s batteries fully charged whenever possible Batteries that are regularly and deeply discharged infrequently charged or stored without a full charge may be permanently damaged causing unreliable power chair operation and limited battery life NOTE The useful life of a battery is quite often a reflection of the care it receives How should I store my power chair and its batteries If you do not use your power chair regularly we recommend maintaining battery vitality by charging the batteries at least once per week If you do not plan on using your power chair for an extended period fully charge the batteries prior to storage Disconnect the battery harnesses and store the power chair in a warm dry environment Avoid temperature extremes such as freezing and excessively hot conditions and never attempt to charge a frozen battery A cold or frozen battery should be warmed for several days prior to recharging What about public transport AGM and Gel Cell batteries are designed for application in power chairs and other mobility vehicles We suggest you contact the carrier s ticket counter in advance to determine that carrier s specific requirements What about shipping If you wish to use a freight company to ship your power chair to your final destination repack your power chair in the original shipping container and ship the batteries in separate boxes
57. wn a kerb or stationary obstacle 1 Approach the kerb or obstacle slowly and make sure the power chair is traveling perpendicular to the obstacle See figure 2 2 Reduce the forward speed just before the front wheels come in contact with the obstacle 3 Increase the forward speed only after the rear wheels have cleared the obstacle and you are once again on a level surface WARNING Even though your power chair may be capable of handling greater obstacles Pride A recommends that you do not attempt to negotiate a kerb that has a height greater than 5 cm MaN 2 in Doing so could cause instability in your power chair WARNING Do not attempt to have your power chair proceed rearward down any step kerb or other obstacle This may cause the power chair to tip 12 www pridemobility com Q6 Edge ll SAFETY Figure 2 Correct Kerb Approach Figure 3 Incorrect Kerb Approach Stairs and Escalators Power chairs are not designed to travel up or down stairs or escalators Always use a lift N WARNING Never use your power chair to negotiate steps or escalators Doors Determine if the door opens toward or away from you E Drive your power chair gently and slowly forward to push the door open Or drive your power chair gently and slowly rearward to pull the door open Lifts Modern lifts have a door edge safety mechanism that when pushed reopens the lift door s Ifyou in the doorway of a lift when the door
58. y Checks B With the controller turned off check the joystick Make sure it is not bent or damaged and that it returns to the neutral position when you release it Check the rubber boot around the base of the joystick for damage Visu ally inspect the boot Do not handle or try to repair it See your Quantum Rehab Dealer if there is a problem Visually inspect the controller harness Make sure that it is not frayed cut or has any wires exposed See your Quantum Rehab Dealer if there is a problem B Check for flat spots on solid tyres Flat spots could adversely affect stability E Inspect the seating system armrests and front riggings for loose hardware stress points or damage See your Quantum Rehab Dealer if there is a problem Weekly Checks Disconnect and inspect the controller from the power base Look for corrosion Contact your Quantum Rehab Dealer if necessary Ensure that all parts ofthe controller system are securely fastened to your power chair Do not overtighten any screws Check for proper tyre inflation Pneumatic tyres should be inflated to the psi bar kPa air pressure rating indi cated on each tyre If a tyre does not hold air see your Quantum Rehab Dealer for replacement of the tube Check the brakes This test should be carried out on a level surface with at least 1 metre 3 feet of clearance around your power chair To check the brakes 1 Turn on the controller and turn down the speed level of your power chair
59. your power chair Avoid using products that may scratch the surface of your power chair If necessary clean your product with an approved disinfectant Make sure the disinfectant is safe for use on your product before application WARNING Follow all safety instructions for the proper use of the disinfectant and or cleaning agent before applying it to your product Failure to comply may result in skin irritation or premature deterioration of upholstery and or power chair finishes J N WARNING Never hose off your power chair or place it in direct contact with water Your power 4 chair has a painted ABS plastic body shroud that allows it to be easily wiped clean with a damp cloth WARNING Never use any chemicals to clean a vinyl seat as they may cause the seat to become slippery or dry out and crack Use soapy water and dry the seat thoroughly Wheel Replacement If you have pneumatic tyres and you have a flat tyre you can replace the tube If your chair is equipped with a solid tyre insert then you must replace the entire wheel assembly Replacement tyres tubes and wheel assemblies are readily available through your Quantum Rehab Dealer WARNING The wheels on your power chair should only be serviced or replaced by a Quantum Rehab Dealer or a qualified technician ff N WARNING Be sure that the controller s power is turned off and the power chair is not in freewheel mode before performing this procedure We WA

Download Pdf Manuals

Related Search

Related Contents

Notice explicative - Faculté de Médecine  Brastemp Side Inverse    Operating System Update: Project Report  Thermo Scientific FHT 1377 GN-2 PackEye  

Copyright © All rights reserved. Failed to retrieve file