Owner`s Manual • FOLLOW SPOT 1200 PRO
Contents
1. Owner s Manual FOLLOW SPOT 1200 P RO S Ha Congratulations on your purchase of this Follower Spot Light To get the most from your equipment you must read all of this manual before using it first time Table of Contents BE A Ee le E 3 j TI A SOC Os eebe 4 EE 5 FOTOS e TNE UNIC EE 7 41 ON s ee 7 Te ATONU EE 4 3 Home Position AdlUSEMENE sins nee 9 I PLOW AD O CG IL ee 10 ie OIA ee el 10 92 Dedicated COM teste dees 11 z NZ CONTU O Os 12 E Te CODI K ON neh release Is O EH beet 14 e DEER 14 ot OS Seen ane ee ee 15 Tecan EE ee 15 1 Safety Instruction You have to carefully read the instruction which includes important information about the installation usage and maintenance e Please keep this User Guide for future consultation If you sell the unit to another user be sure that he also receives this instruction booklet e Unpack and check carefully there is no transportation damage before using the unit e Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit as stated in this manual e Its important to ground the yellow green conductor to earth in order to avoid electric shock e The unit is for indoor use only Use it only in a dry location Exposing the device to rain or moisture would cause the risk of electrical shock or fire e The unit must be installed in a location with adequate ventilation at least 50 cm from adj2. is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the dimmer home position Once the effect has been selected press the ENTER button to setup or automatically return to the offset functions after 8 seconds without any change Press the MENU button again to go back to the main functions without any change 5 How to control the Unit Two ways to operate 1 By universal DMX controller 2 By dedicated controller There s no need to turn the unit off when you change the DMX address as the new DMX address setting will be effective at once Every time you turn the unit on it will show 1200 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive the DMX signal 5 1 DMX Controller If you use an universal DMX controller to control the units you have to set DMX address from 1 to 512 channels so that the units can receive the DMX signal Press the MENU button up to when the Addr is shown on the display Press the ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep the ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to a
3. acent surfaces Be sure that no ventilation slots are blocked e Disconnect the device from the mains power before any servicing or maintenance e Replace fuse lamp only with the same type Do not use any other type of lamp e Keep any flammable material away from the unit while it is operating Otherwise you run the risk of causing a fire Use safety cables when fixing this unit Don t handle the unit by taking its head only but always by taking its base e Maximum ambient temperature is TA 40 C Dont operate it where the temperature is higher than this e Unit surface temperature may reach up to 85 C Dont touch the housing barehanded during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing bulb or servicing as the unit could be very hot Also dont touch the bulb with bare fingers as it is very hot after using e Hot lamp explosion hazard Do not open the unit within five minutes after switching off e Do not start the unit without bulb enclosure or if the housing is damaged e The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged e In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance centre Always use the same type spare pa
4. ddress your DMX512 channel for the first 4 units 5 2 Dedicated Controller 6 channels for international protocol DMX512 It can finish all operations via dedicated controller without using other controllers When the power is switched on the projector automatically starts to run the self test After finishing these the fixture is ready for operation 1 6 7 8 9 1 1 DIMMER OPEN buttons Holding the buttons the light beam will become stronger and stronger then shutter will obtain max value After releasing the button the light beam and shutter resumes its initial condition There are 2 buttons on the both sides of the controller for your convenient operation 2 IRIS OPEN buttons Holding the buttons the light iris will become bigger and bigger After releasing the button it the light beam resumes its initial condition There are 2 buttons on the both sides of the controller for your convenient operation 3 FIXED COLOURS amp RAINBOW switch Turning the switch on the RAINBOW position enable the rainbow function you can set different rainbow speed by pressing COLOUR buttons from slow to fast Turning the switch on the FIXED COLOURS position enable the fixed colours function and disable the rainbow function They will save last setting automatically in each step 4 COLOUR buttons There are 9 colour buttons of white red yellow magenta green orange blue pink and purple Select the light beam colours by pressing the r
5. e previous one 3 Try to use another DMX controller 4 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken Consult your dealer then 2 The motor s drive IC on the PCB might be out of condition Consult your dealer then D The lamp is cutting out intermittently 1 The lamp is not working well Let a technician check for proper mains voltage 2 Internal temperature may be too high Check and if necessary replace the fan 7 Fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimise light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can cause higher accumulation of dirt on the units optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days Do not dispose of the device at the end of his operating life H in your normal domestic waste This device is subject to the European Guidelines 2002 96 EC ma e Have the product disposed of by a professional disposal company of by your communal disposal facility Observe the c
6. elative colour buttons 5 COLOUR TEMPERATURE switch Adjusting this switch to obtain 3 kinds of colour temperature Standard 6000K 5600K and 3200K 6 DIMMER slider Adjusting the slider from 0 to 100 position the light beam will become more stronger and stronger till the dimmer reach 100 SHUTTER slider Adjusting the slider from slow to fast position the strobe speed will become from slow to fast IRIS slider Adjusting the slider from min to max position the light beam size will become more bigger and bigger till the iris opened fully FOCUS slider Adjusting the suitable focus by pushing this slider from left to right 5 3 DMX512 Configuration DMX 512 Lessel 113 127 Pink 099 112 UV purple ONS 068 Blue OT1 084 Orange 057 070 Green 020 042 Yellow 015 028 Red 000 014 White 5 4 DMX512 Connection The DMX 512 is widely used in intelligent lighting control offering a maximum of 512 channels COMMON Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 If you re using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug a
7. hing off Because of its high internal pressure there might be a risk that the discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if one looks directly at the lamp MSI 1200W S HMI 1200 S K SFc15 5 6 1 Always switch off the main supply and never handle the lamp or luminant when it is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp any longer than its specified life 5 Make sure the lamp is located in the centre of the reflector for the best spot Unscrew the thumb screw 6 If changing the lamp remove old lamp from lamp socket Hold the new lamp only by its ceramic base Never touch the glass bulb Insert the new lamp in the lamp socket 7 With the nipple of the lamp facing the back insert one end of the lamp into the socket Pull up the spring of the other side of the socket and snap the other end of the lamp into place Make sure it fits correctly into the socket Please refer to the diagram to kno
8. ink Use DOWN UP buttons to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main function without any change after 8 seconds To go back to the functions without any change press the MENU button again t c 5 Self test Press the MENU button until the 2 SE is blinking on the display Press the ENTER button and the unit will run the built in program for self testing To go back to the functions press the MENU button Fh Fixture Hours Press the MENU button up to when the Fhe Sis blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again i m III ll II Lamp ON OFF Press the MENU button until the L Ni r is blinking on the display Press the ENTER button and the display will blink Use DOWN and UP button to selectthe on Lampon or okt Lamp off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Jt E Reset Press the MENU button until the r STE is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again 4 3 Home Position Adjustment Press MENU butto
9. n for at least 5 seconds into offset mode to adjust the home position when viol want to adjust gobo and colour home position you should be run F Hei mode first the functions are shown below ie i L L 13 Color offset 127 127 igi MENU oEFt EK Effect offset 127 127 a rti l Sool tt LZ Dimmer offset 127 127 l LIL UL Colour offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the n _ ou is shown on the display Press the ENTER button and the display will blink Use DOWN and UP buttons to adjust the colour home position Once the colour has been selected press the ENTER button to setup or automatically return to the offset functions after 8 seconds without any change Press the MENU button again to go back to the main functions without any change _ LL d MEN L Effect offset Press the MENU button for at least 5 e into offset mode use DOWN and UP button up to when the GE FE is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the effect home position Once the effect has been selected press the ENTER button to setup or automatically return to the offset functions after 8 seconds without any change Press the MENU button again to go back to the main functions without any change sit old Dimmer offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the
10. nd plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split to a Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX signal is able to pass through each fixture continuously so if one fixture in the chain is out of order all the fixtures after this point will not be affected 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 08 1 are equal to 1 6 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 6 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the mains power supply and mains fuse 2 Let a technician check the mains outlet for proper functioning B Not responding to DMX controller 1 Check the address settings and DMX polarity 2 If you have intermittent DMX signal problems let a technician check the pins on connectors or on PCB of the unit or th
11. rts e Do not connect the device to any dimmer pack e Do not look directly at the light while the unit is on There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs by yourself If the fixture shows any visible damage or if your unit may require service please contact your nearest dealer e The unit must be mounted via its mounting system as show below Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 80 kg for each unit 2 Technical Specification Power supply e AC 230V 50Hz Lamp e MSI 1200W S HMI 1200 S K SFc15 5 6 Optical system e High efficiency optical system e High quality optical lens and dichroic colours e Beam angle 13 Shutter Dimmer e Blackout 0 100 smooth dimming and strobe speed variable 1 12 flashes per second Movement e Pan 360 Tilt 90 Colour Wheel e 8 dichroic colours plus white colour e Rainbow effect at variable speeds Colour Temperature e Standard 6000K adjustable 5600K and 3200K DMX Channels e Standard DMX512 signal addressing and controlled by any universal DMX controller l l l l l CS i d d i 6 T B a 10 Di ioanceimh In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switc
12. urrently applicable regulations In case of doubt contact your disposal facility e Dispose of packaging materials in an environmentally ON responsible manner QS 9 Technical Specifications Power AC 230V 50HZ Fuse 6 x 30 mm Glass T15A Lamp MSI 1200W S HMI 1200 S K SFc15 5 6 Dimension 1170 x 330 x 225 mm Weight 42 4 kg 2010 Musikhaus Thomann Treppendorf 30 96138 Burgebrach Germany e www thomann de
13. w how to put the lamp in correct position 4 How to setup the Unit 4 1 Control Panel CH 2 IRIS pes de os COLOR TEMPERATURE ia FR a FOCUS G S12 LINK Pip hEn pini re Fe D r T Display To show the various menu and to select functions Button MENU To select the programming functions DOWN To go backward in the selected functions To go forward in the selected functions ENTER To confirm the selected functions On Off Turns On Off the power Fuse To replace the fuse Power To connect the power plug DMX input output For DMX 512 link use 5 pin XLR plug cable to link the unit together _4 2 Main Funttion 3 I5 5III IllklW To select any of the given functions press the MENU button up to when the required one is showing on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are showing below Addr Divix512 Address Settine T LESE Self Test MENU FhrS Fixture Hours Lamp on uap 20 i orF Lamp off rSPF Reset Rede DMX 512 Address Setting Press the MENU button until the Adder is showing on the display Press the ENTER button and the display will bl
Download Pdf Manuals
Related Search