OPERATION MANUAL
Contents
1. See Drawing 2A Using only wrench provided screw the bottle cylinder inward until it is seated See Drawing 2B DO NOT OVER TIGHTEN Use only the wrench provided with the gun to prevent the bottle from being over tightened Using any other wrench will produce more torque than the wrench provided damaging threads and resulting in serious injury With the gun pointed in a safe direction it can then be dry fired with CO2 only to find out if the CO2 bottle cylinder is installed correctly If no CO2 shoots from the gun the shooter should retighten the CO2 bottle cylinder again using only the wrench provided being careful not to over tighten it Never assume any gun is unloaded Follow all safety rules O RINGS The O ring on the refillable CO2 bottle cylinder should be replaced when it is found to be damaged The O ring is an easily replaceable part These O rings are available from Daisy and from stores where paintball supplies are sold REMOVING THE CO2 SOURCE FROM THE GUN Whenever the shooter notices that the CO2 pressure is becoming lower in the CO2 bottle cylinder it should be removed from the gun When the CO2 pressure is allowed to become very low or completely depleted it may cause a pellet to fail to shoot out of the gun The pellet may remain inside the chamber or part way down the barrel of the gun This remaining pellet may or may not shoot out of the gun when the gun is shot the first time after a full CO2 sour2. an a a a E o n 888 P 887 GOLD f MEDALIST MEDALIST t i NOT A TOY THIS AIRGUN IS DESIGNED FOR USE BY EXPERIENCED SHOOTERS AND IS INTENDED FOR MATCH COMPETITION OR TARGET RANGE USE MISUSE OR CARELESS USE MAY CAUSE SERIOUS INJURY OR DEATH MAY BE DANGEROUS UP TO 257 YARDS 235 METERS THIS IS A SPECIAL CLASS OF NON POWDERED GUNS AND NOT FOR GENERAL USE IT IS TO BE USED FOR TRAINING AND TARGET SHOOTING UNDER SUPERVISION RECOMMENDED FOR USE BY THOSE 16 YEARS OF AGE OR OLDER THIS GUN SHOOTS PELLETS ONLY READ ALL INSTRUCTIONS BEFORE USING THE PURCHASER AND USER SHOULD CONFORM TO ALL LAWS GOVERNING THE USE AND OWNERSHIP OF AIRGUNS gt K Compet Use 177 cal 4 5 mm Lead Airgun Pellets FJ A WARNINGS THIS GUN CAN CAUSE SERIOUS INJURY OR DEATH READ AND FOLLOW THE INSTRUCTIONS CAREFULLY DO NOT LOAD A PELLET INTO THE GUN UNTIL YOU ARE READY TO SHOOT IF YOU DO LOAD A PELLET AND THEN DECIDE NOT TO SHOOT REMOVE IT EITHER MANUALLY OR BY SHOOTING THE GUN AT A SAFE TARGET AN UNLOADED UNCOCKED GUN WHICH IS ON SAFETY IS SAFEST ACCIDENTS HAPPEN FAST AND ACCIDENTALLY INJURING OR KILLING SOMEONE IS A TERRIBLE THING PLEASE SHOOT SAFELY This safety alert symbol indicates important safety messages in this manual When you see this symbol be alert to the possibility of personal injury and carefully read the message that follows The Avanti Models 887 and 888 Competition Pelle
3. Your gun is now ready to shoot In this condition it should be handled with extreme care Step 8 FIRE After completing the operating steps above and after making sure the gun is pointed in a safe direction gently but firmly squeeze the trigger Repeat steps 1 through 8 to continue shooting FAILU RE TO SHOOT Co2 If the gun does not shoot CO2 with the safety ON NO RED SHOWING and with the gun pointed in a safe direction try retightening the 2 5 ounce bottle cylinder with only wrench provided Do not over tighten If the gun still does not shoot CO2 the CO2 source may be empty The 2 5 ounce refillable bottle cylinder can be checked for CO2 pressure by removing it from the gun and pushing inward on the bottle cylinder valve pin If the valve can be opened and no gas escapes the CO2 bottle cylinder is empty and should be refilled to operate the gun FAILURE TO SHOOT A PELLET tthe gun does shoot CO2 but does not shoot the pellet one or more pellets may be jammed in the barrel of the gun An unfired projectile in the barrel can be a dangerous situation WARNING IF A PELLET DOES NOT FIRE AFTER COMPLETING THE OPERATING STEPS THE GUN IS JAMMED KEEP THE GUN POINTED IN A SAFE DIRECTION AND PERFORM THE FOLLOWING STEPS 1 Put trigger safety ON NO RED SHOWING 2 Open bolt 3 Close bolt and with gun pointed in a safe direction take the trigger safety OFF RED SHOWING and fire If the pellet still do
4. gun If a safe target is not available put trigger safety ON NO RED SHOWING open bolt invert the gun with the barrel held horizontal insert a cleaning rod in the muzzle end and push the pellet out of the barrel This allows the pellet to fall clear of the action Do not allow a pellet to fall into the action of the gun DO NOT use a steel cleaning rod Use brass or aluminum only Ad caution Never assume the gun is empty of projectiles Always point the gun in a safe direction AMMUNITION Use only 177 4 5 mm lead airgun pellets Daisy no 557 match pellets are recommended 6 REAR SIGHT INSTALLATION AND ADJUSTMENT MODEL 887 This is a universal target sight with a rubber eyepiece which prevents light reflecting from the sight into your eye ELEVATION o hiha ADJUSTMENT WINDAGE ADJUSTMENT MOUNTING SCREW ELEVATION NO 6 CALIBRATION Installation Step 1 Loosen the bracket mounting screw and plate Slide the sight onto the dovetail grooves of the receiver Position the sight forward or to the rear until it suits your eye sight and or physique Installation Step 2 Tighten mounting screw securely See drawing 6 ELEVATION To lower the point of impact turn elevation knob to the left counterclockwise To raise the point of impact turn elevation knob to the right clockwise per arrow and word UP See drawing 7 WINDAGE To move the point of impact to the left turn the windage knob counterclockwise To
5. instructors should make sure that inexperienced shooters use this model with the trigger adjustment screw backed out to maximum trigger travel For target shooting experienced shooters may find that the best trigger travel setting can be obtained by with the safety at ON NO RED SHOWING the gun unloaded and with the CO2 source removed carefully turning the adjustment screw inward until slight resistance is felt After the trigger has been adjusted with the gun pointed in a safe direction and with no pellet or CO2 in the gun it should be dry fired several times and the safety tried several times to make sure that the trigger sear and safety are all functioning correctly If the gun does not seem to be functioning correctly the adjustment screw should be turned outward 1 2 turn and the gun tried for function again As the trigger is being adjusted the shooter should be careful that the adjustment screw is not forced because the sear and the safety mechanism can be damaged If the shooter has questions about the proper way to adjust the trigger they can call the Daisy Customer Service Department for information on doing this BURST DISK SAFETY PRESSURE RELIEF The 2 5 ounce refillable CO2 bottle cylinder has a burst disk safety pressure relief on the front fitting of the bottle cylinder The disk will burst or rupture to safely relieve excess CO2 gas pressure to prevent the pressure from becoming too high The pressur
6. position and have the CO2 source removed from the gun STOCK AND FOREARM The wooden stock may be wiped clean with a damp rag and lightly waxed EXTERIOR PARTS Exposed metal parts i e receiver barrel etc should occasionally be wiped clean using a soft lightly oiled cloth Use a clean 30 weight non detergent motor oil BARREL The barrel should be cleaned occasionally to maintain accuracy We recommend using Daisy Model 5878 Cleaning Kit To clean barrel open bolt remove CO2 source then insert a brass or aluminum cleaning rod and oil saturated patches into the muzzle end of the bore Retract the rod and patch from the barrel Repeat this procedure several times with oiled patches then switch to dry patches Continue using dry patches until most of the oil is removed from the bore NOTE Be careful not to damage the sealing tip on the bolt when the rod tip enters the loading area It may be necessary to clean the barrel approximately every 50 shots to maintain maximum accuracy Frequent cleaning may be necessary when the gun is new and until excess oil is removed LUBRICATION The easiest and best way to lubricate these models is to place a drop of 30 weight non detergent motor oil on the CO2 source before it is installed into the gun Using the 2 5 ounce refillable CO2 bottle cylinder the gun can be lubricated each time it is installed into the gun This can be done by placing one drop of 30 weight non detergent motor oil onto th
7. vary from state to state IMPORTANT You can return your inoperative rifle to Daisy for repair via United Parcel Service UPS Be sure to put ON NO RED SHOWING safety and unload all ammo before returning the gun to Daisy You must include your street address for Daisy to send your rifle directly back to you through UPS delivery GUNS OUT OF WARRANTY If your Avanti gun needs repair please call 1 800 713 2479 for repair charges Daisy will repair the gun or replace it with a reconditioned gun of the same model if available otherwise with a model of equivalent quality Daisy Outdoor Products Service Department 308 W Stribling Drive Rogers AR 72756 U S A NOTE AVANTI air guns do not come under the provisions of the Gun Control Act Of 1968 and can be shipped via UPS not mailed 12 MODEL 887 888 SPECIFICATIONS ACTION CALIBER AMMUNITION FRONT SIGHT REAR SIGHT BARREL MUZZLE VELOCITY MUZZLE ENERGY TARGET DISTANCE MAXIMUM SHOOTING DISTANCE LENGTH WEIGHT ADD ON ACCESSORIES CO2 power single shot bolt 177 cal 4 5 mm 177 cal 4 5 mm lead air gun pellets 887 Globe type with changeable aperture inserts 888 Hooded with changeable aperture inserts 887 Dilopter sight with micrometer click adjustment for windage and elevation 888 Micrometer adjustable peep sight Rifled steel with barrel weight 12 lands and grooves right hand twist precision bore sized for ma
8. DEL IS NOT DESIGNED TO USE A newly purchased Daisy 2 5 ounce refillable CO2 bottle cylinder will be empty It will not have CO2 in it until it has been filled These bottles can be filled with CO2 at stores where CO2 paintball marker cylinders are filled 3 INSTALLING THE FILLED 2 5 OUNCE REFILLABLE CO2 BOTTLE CYLINDER INTO THE GUN AX WARNING USE ONLY WRENCH PROVIDED OVER TIGHTENING CYLINDER MAY CAUSE SERIOUS INJURY Over tightening a CO2 cylinder during installation can cause severe damage to the cylinder threads which may result in serious injury to the person installing the cylinder The most common cause of over tightening is using a wrench other than the one included with the cylinder Other wrenches provide more torque than the wrench provided and can severely damage the cylinder Because the O ring on the cylinder not a brass to brass seal is the true point of seal over tightening does NOT ensure a better seal Rather it can destroy the O ring damage the threads of the cylinder and the rifle prevent a correct and effective seal and cause damage leading to serious injury INSTALLING Coat the threads of the bottle and the O ring with 30 weight non detergent motor oil Keep the gun pointed in a safe direction IT IS VERY IMPORTANT TO ALWAYS KEEP THE GUN POINTED IN A SAFE DIRECTION WHILE INSTALLING OR REMOVING THE CO2 BOTTLE CYLINDER Insert the threaded fitting end of the CO2 bottle cylinder into the forearm of gun
9. SAFE DIRECTION Step 1 PUT ON TRIGGER SAFETY Step 6 AIM AT SAFE TARGET NO RED SHOWING Step 7 TAKE OFF TRIGGER SAFETY Step 2 OPEN BOLT RED SHOWING Step 3 INSTALL CO2 Step 8 FIRE Step 4 LOAD PELLET Step 5 CLOSE BOLT DOVETAIL GROOVES ZL FEED TRIGGER SAFETY ON NO RED SHOWING BOLT HANDLE Uy TRIGGER SAFETY LOK OFF N RED SHOWING ON TRIGGER SAFETY OPPOSITE SIDE waRNING BE SURE GUN IS ALWAYS POINTED IN A SAFE DIRECTION NEVER POINT THE GUN AT ANYONE ALWAYS ASSUME AND HANDLE THE GUN AS IF IT WERE LOADED AND READY TO FIRE STEP 1 PUT ON TRIGGER SAFETY Push the trigger safety from left to right so that NO RED IS SHOWING It is a good practice to get into the habit of always keeping the trigger safety ON NO RED SHOWING until actually ready to fire the gun See Drawing 1A STEP 2 OPEN BOLT FEED TRACK Pull the bolt handle fully to the rear Then release your a hold on the bolt handle leaving the bolt open The gun BOLT HANDLE cannot fire with the bolt open See Drawing 1B STEP 3 INSTALL CO2 NO 1B O TRIGGER SAFETY The model 887 and 888 CO2 pellet rifles are energized by CO2 only from a refillable 2 5 ounce removable CO2 bottle cylinder designed for use in this model Ad Wwarnine DO NOT ATTEMPT TO USE COMPRESSED AIR OR ANY GASSES OTHER THAN CO2 IN THESE MODELS Ad warnine DO NOT ATTEMPT TO USE ANY TYPE OF CO2 BOTTLE CYLINDER OR FITTINGS THAT THIS MO
10. and See Drawing 8D 5 To replace aperture depress release plate Place desired aperture in position with insert tabs in appropriate slots See Drawing 8D 6 Front sight apertures provided with this airgun measure 140 inch 150 inch 160 inch and 170 inch Post front sight width measures 1 7526 mm 069 inch SLING ATTACHMENT The sling is attached by a detachable sling swivel which connects to a sling bracket on the forward end of the accessory rail With the sling attached to the swivel and pulled back along the underside of the rifle the tab end of the sling should be hanging down See Drawing QA SLING SWIVEL RIFLE LOOP SLING BRACKET TAB END SLING OF SLING SWIVEL LENGTH ADJUSTING KEEPER PUTTING SLING ON ARM 1 Open the arm loop 2 Turn loop one quarter turn in the direction of the sling arm i e one quarter turn to the left if the sling is going on the left arm and slip your arm into the loop See Drawing 9B 3 Place sling loop on your upper arm either above the bicep near the shoulder or below the bicep 4 Tighten the sling loop until it is snug enough to remain in place on your arm It should not be so tight that it restricts the flow of blood to your arm or creates a pulse effect LENGTHENING SLING Grasp the tab end of the keeper with your trigger hand and lift it up while pulling on the top strand not the tab end of the sling See Drawing 9C SHORTENING SLING Pull the tab end of
11. awing 6A Position the sight forward or to the rear until it suits your eye sight and or physique Installation Step 2 Tighten mounting screws securely See Drawing 6A ELEVATION To lower the point of impact turn elevation knob to the left counterclockwise To raise the point of impact turn elevation knob to the right clockwise per arrow and word UP See Drawing 7A WINDAGE To move the point of impact to the left turn the windage knob counterclockwise To move the point of impact to the right turn the windage knob clockwise per arrow and letter R See Drawing 7A ADJUSTMENT This precision peep sight is fully adjustable Each click of the micrometer adjustment results in a 413 minute of angle 048 inch shift of pellet impact at 10 meters 83 feet FRONT SIGHT APERTURE INSERTS MODEL 888 RELEASE PLATE INSERT TABS APERTURE INSERT RELEASE PLATE NO 8D Your model 888 competition pellet rifle comes with additional aperture inserts one is already in place To change inserts follow this procedure 1 Point the muzzle up and away from you in a safe direction 2 Open the bolt and put the gun ON safety NO RED SHOWING 3 Using your index finger or middle and index fingers if your fingers are slender push in on the top and bottom of the release plate See Drawing 8C 4 With insert release plate pushed in lift out the aperture insert with thumb and index finger of opposite h
12. ce has been reinstalled This can create a very dangerous condition and can be avoided by not allowing the CO2 source to become completely emptied while the gun is being used The shooter should always assume that a pellet may be in the gun and the gun should always be kept pointed in a safe direction and should NEVER be dry fired unless the gun is pointed in a safe direction REMOVING THE 2 5 OUNCE REMOVABLE CO2 BOTTLE CYLINDER FROM THE GUN CO2 pressure can cause the bottle cylinder O ring to seal very tightly in the gun and can cause the bottle cylinder to be harder to unscrew To help keep this from happening the shooter should always be sure to oil the O ring and threads of the bottle cylinder before installing it and should avoid over tightening it by always using only the wrench provided While the pressurized bottle cylinder is being unscrewed from the gun a small amount of CO2 can usually be heard escaping This is normal A Being sure to keep the gun pointed in a safe direction and always using only the wrench provided unscrew the bottle cylinder and remove it from the gun NOTE As the bottle cylinder is being unscrewed the shooter should be observant for any movement or loosening of the bottle cylinder fittings If this is found or if the shooter experiences any problems when they are installing or removing the CO2 source the gun and CO2 source should be stored in a safe place and the
13. e center of the face of the fitting that screws into the gun This will be on the valve pin on the 2 5 ounce refillable CO2 bottle cylinder Use one drop only More than that can cause the bottle cylinder or adapter to seem to be completely screwed into place when it is not CO2 will not feed into the gun until the bottle cylinder has been retightened Also too much oil can flood the valve of the gun and cause the gun to shoot low pellet velocities ONE DROP OF OIL WILL LUBRICATE THE GUN PROPERLY IMPORTANT The only oils recommended for use in the 887 888 are 30 weight automotive motor oils DO NOT use light household type oils or aerosol type spray lubricants since they may contain substances or additives harmful to the rubber seals and other components STORAGE To make your 887 888 safe for storage or transporting proceed through operating Steps 1 through 8 omitting Step 4 Loading WHILE POINTING THE GUN IN A SAFE DIRECTION FOR THE ENTIRE TIME Then put the trigger safety ON NO RED SHOWING This will ensure that the hammer is fired that there is not a pellet in the chamber and that the trigger safety is ON Remove CO2 source NEVER STORE A LOADED OR COCKED GUN KEEP AWAY FROM CHILDREN AND UNTRAINED SHOOTERS Always store pellets in a place separate from the gun to keep them from untrained shooters Before putting your gun away make sure it is clean dry oiled unloaded uncocked and that the CO2 cylinder has been remo
14. e inside the bottle cylinder could become too high from the bottle cylinder being overfilled with CO2 or from the bottle cylinder becoming heated by being left in direct sunlight or from some other source The burst disk is a replaceable part but replacing the disk should be done by trained personnel only Ruptured burst disks can be replaced by personnel at stores where these CO2 bottle cylinders are filled When a burst disk does rupture to relieve the excess pressure in the CO2 bottle cylinder all of the CO2 in the bottle cylinder will escape rapidly from the bottle cylinder The rapidly emptying CO2 bottle cylinder will quickly become coated with frost The shooter should avoid contact with the escaping CO2 and the frosted bottle cylinder If the disk bursts inside an automobile or in some other enclosed area a window or door should be opened to allow the CO2 to dissipate 10 PROPER CARE With periodic cleaning and lubrication your 887 888 will provide many years of shooting enjoyment As is the case with conventional firearms abuse neglect and continued exposure to the elements will impair the performance of any airgun and could make the gun unsafe Learn to take care of your 887 888 and it will serve you well Ad caution Never attempt to clean this gun until you put the trigger safety in the ON position NO RED SHOWING have made absolutely certain that the gun is not loaded have the bolt in the fully open
15. es not fire follow these steps carefully 1 Put trigger safety ON NO RED SHOWING 2 Open bolt 3 With gun pointed in safe direction remove CO2 source from the gun using only wrench provided 4 Invert the gun with the barrel held in the horizontal position 5 Clear barrel by running a brass or aluminum cleaning rod through from the muzzle end using a steel rod will damage rifling and allow the pellet to fall clear of the receiver through the feed track Be careful not to damage the bolt tip by pushing the rod through too hard Do not reuse this pellet Do not allow a pellet to fall into the action of the gun NOTE Should you let a pellet fall into the action of the gun make every effort to shake it free and get it to fall out Otherwise the gun will have to be returned to the Daisy Service Department See Repair of Daisy Guns section 6 Repeat operating Steps 1 through 8 If after following the firing procedure a pellet is not fired put safety ON NO RED SHOWING and return your gun to the Daisy Service Department If these steps do not correct the problem the gun and CO2 source should be stored in a safe place The Daisy Customer Service Department should be called for information on correcting the problem or for information on how to return the gun and CO2 source for repair Do not return the gun to the retailer UNLOAD PELLET The bolt does not extract a pellet Shoot the pellet at a safe target to unload
16. move the point of impact to the right turn the windage knob clockwise FRONT SIGHT APERTURE INSERTS MODEL 887 Your model 887 competition pellet rifle comes with four aperture inserts 2 6 mm 3 8 mm 4 0 mm 4 4 mm 4 4 mm already in place To change inserts follow this procedure 1 Point the muzzle up and away from you in a safe direction 2 Open the bolt and put the gun ON safety NO RED SHOWING 3 Grip the ring at the muzzle end of the sight and turn counterclockwise If tight a coin may be used in the slots See drawing 8A 4 Unscrew until aperture is free to be removed by using finger and thumb on side of sight tube engaging ears on aperture to pull back and upwards See drawing 8B Note Apertures have ears of different sizes to ensure the proper positioning when replaced 5 To install make sure back locking ring is unscrewed far enough for clearance Have ears to proper side Insert in groove and push forward Tighten locking ring A coin may be used to assure a firm lock REAR SIGHT INSTALLATION AND ADJUSTMENT MODEL 888 WINDAGE ADJUSTMENT rae MOUNTING SCREWS ELEVATION ADJUSTMENT KNOB DOVETAIL GROOVES PEEP SIGHT MOUNTING SCREWS WINDAGE CALIBRATION WINDAGE ADJUSTMENT ELEVATION ADJUSTMENT KNOB ELEVATION CALIBRATION under knob PEEP SIGHT NO 7A Installation Step 1 Loosen bracket mounting screws and slide receiver sight onto dovetail grooves of receiver See Dr
17. shooter should call the Daisy Customer Service Department for information on handling the problem Only trained personnel should attempt to work on the refillable bottle cylinder or on the gun ee TRACK BOLT HANDLE BOLT TIP Step 4 LOAD PELLET With the bolt back lower the muzzle slightly and load a 177 cal 4 5 mm pellet solid end forward See Drawing 4A Step 5 CLOSE BOLT Push the bolt handle fully forward This will chamber a pellet and lock the bolt See Drawing 4B The gun will not fire if the bolt is open AX caution The gun is now loaded and ready to fire Pulling the trigger now will fire a pellet from the gun In this condition it should be handled with extreme care Step 6 AIM AT SAFE TARGET Aim the gun at a safe target To be a consistent marksman use the correct sight picture each time you fire your gun See Drawing 5 FRONT SIGHT BULLSEYE Ad caution Due to the power of these airguns use extra caution in selecting a safe target backstop These models should not be used with BB gun target backstops Pick targets that cannot be penetrated or that will not cause a ricochet because of their hard surface Use only targets and traps that are designed for use with high powered pellet guns Do not shoot at water Step 7 TAKE OFF TRIGGER SAFETY When you are certain the target backstop and surrounding area are safe push the trigger safety from the right fully to the left RED SHOWING ON LEFT
18. t Rifles shoot with much more muzzle energy than many BB and pellet guns Use extreme caution when operating these guns Although your new Avanti Competition Air Rifle is not a firearm it has lethal potential and should be treated with the caution and respect due any conventional firearm Like a firearm your Avanti Competition Air Rifle when misused or carelessly used can kill or seriously injure the shooter or other persons Always remember the first and most important safety feature of any gun is the shooter All safeties are mechanical devices and the shooter is the only part of the system that can make a gun safe or unsafe DON T DEPEND ON MECHANICAL SAFETIES think ahead and avoid situations that might lead to accidents Guns differ in their operation and you are never ready to fire any gun until you are thoroughly familiar with it Read the following operating instructions and WITHOUT LOADING ANY PELLETS proceed through the operating steps dry firing your gun several times at a safe target This will enable you to learn to operate this Avanti Competition Air Rifle properly and safely NOTE Models 887 and 888 are identical except for stock and sights MODEL 887 SHOWN FEED TRACK LEFT SIDE BARREL WEIGHT S aie BOLT HANDLE PISTOL GRIP RIGHT SIDE REAR SIGHT sa FRONT SIGHT C02 BOTTLE TRIGGER FOREARM CYLINDER TRIGGER SAFETY FIGURE NO 1 HOW TO OPERATE WARNING BE SURE GUN IS ALWAYS POINTED IN A
19. tch pellets 500 fps 152 mps 4 28 ft Ib 5 8 J 33 ft 10 m 257 yds 235 m 38 5 in 97 7 cm 887 7 3 lbs 888 6 9 Ibs Standard dovetail mount in receiver to accept a scope nylon web sling With muzzle pointed upward at optimum angle AVANTI Models 887 and 888 Parts List Part No 888 1 887 1 888 2 888 3 888 4 888 5 888 6 888 7 888 8 888 9 888 10 888 11 888 12 888 13 888 14 887 14 888 15 887 15 888 16 888 17 888 18 15 Description 888 stock butt plate and screws 887 stock butt plate and screws Stock spacers 3 each Trigger housing Safety assembly includes ball amp spring Trigger assembly Hammer and spring Receiver Bolt handle assembly includes bolt bolt handle and spring Valve body and barrel assembly Right filler Left filler Frame Barrel band 888 front sight and set screws 887 front sight and set screws 888 sight inserts 887 sight inserts O ring Burst disk and relief valve Screw assortment includes 2 receiver screws 1 trigger housing screw 1 trigger adjustment screw 1 rear tie down valve body screw 2 stock screws 1 seat screw O ring valve group includes O ring spring valve Adapter 888 rear sight 887 rear sight
20. the sling away from you until sling reaches the desired length See Drawing 9D STOCK ADJUSTMENTS SPA TRS To adjust the stock loosen screws in butt PEIE ENEE plate sufficiently to allow insertion of the desired a an number of spacers See Drawing 10 Spacers go between stock and butt plate Each insert will BUTT PLATE adjust stock length 5 8 inch 625 inch After stock SCREWS adjustment inserts have been added tighten butt plate screws to lock inserts in place To shorten the stock reverse this procedure Be certain spacers are placed so the molded cleats nest in the molded NO 10 receptacle 9 TRIGGER ADJUSTMENT The trigger in this model is adjustable for travel This is a Special TRIGGER Purpose Match Precision Gun and is exempt from the 2 Ib 0 9 ADJUSTMENT kg minimum trigger pull standard The trigger adjustment screw is located behind the trigger guard See Drawing 11 The adjustment screw can be turned outward until it has no effect and trigger travel is at the maximum or it can be turned inward to shorten the trigger travel To adjust the trigger travel in this model the gun should be kept pointed in a safe direction the safety should be at ON NO RED SHOWING the gun should be unloaded and the CO2 source should be removed from the gun CAUTION The trigger should be adjusted by an experienced shooter only After the trigger has been adjusted the gun should be treated with caution Coaches and
21. ved If the gun is to be stored for a long period of time a light coat of oil in the barrel will help prevent corrosion 11 MODIFICATION AX CAUTION The components of this gun were engineered to deliver optimum performance Any modification or tampering with a gun may cause a malfunction and may make it unsafe to use Any change in performance such as a lowered trigger force and shortened trigger travel indicates possible wear Such guns should be inspected replaced or properly repaired by qualified personnel Any gun that has been dropped should be checked by qualified personnel to insure that its function has not been affected AM WARNING A GUN THAT IS NOT OPERATING PROPERLY MAY BE DANGEROUS IT SHOULD BE KEPT SAFELY FROM USE BY ANYONE UNTIL REPAIRED OR DESTROYED DO NOT TRY TO TAKE THE GUN APART IT IS DIFFICULT TO REASSEMBLE AND IMPROPER REASSEMBLY CAN CAUSE A HAZARDOUS CONDITION GUNS IN WARRANTY LIMITED ONE YEAR WARRANTY For one year from date of purchase Daisy will repair or replace and return this gun free of charge if defective in material or workmanship Service is available by returning the gun to Daisy Outdoor Products refer to important note below Attach to the gun your name street address telephone number description of problem and proof of date of purchase sales slip Package and send transportation prepaid to Daisy This warranty gives you specific legal rights and you may also have other rights which may
Download Pdf Manuals
Related Search