File - Hawk Measurement Systems
Contents
1. be consulted for advice 9 List of ATEX certified equipment types Sultan Acoustic Wave Remote Electronics AWR series Sultan Acoustic Wave Remote Transducer AWRT series Sultan Acoustic Wave Integral Transmitter AWI series Sultan Acoustic Wave Smart Transducer AWST series Flange Cone and Accessory Selection in any combination 10 Wiring Configuration drawings Note All equipment in Zone 20 Hazardous area must have ATEX Cat 1D marking HAW_RD_WIR ATEX H1 A20_ jpg HAW_RD_WIR ATEX J1 A20_ jpg 04 Safety Instr v2 ATEX Cati D A20_Sultan doc Page 5 of 7 Hawk Measurement Systems Pty Ltd www hawklevel com H1 Wiring for ATEX Category 1 D Sultan 3 amp 4 wire Remote Amplifier in Safe Zone amp Remote Transducer in Zone 20 Hazardous Area Note All equipment in Zone 20 Hazardous area must have ATEX Cat 1 D marking Certificate No ITSO4ATEX12896X ATEX Rating gt can External Environment Rating Zone 2 22 ATEX Category 3 or Safe Area AC DC Power a 4 20mA Current Loop Isolated r Optional B Shield PLC Comms SULTAN ORCA or Panel Mount REMOTE AMPLIFIER Note 1 04 Safety Instr v2 ATEX Cati D A20_Sultan doc SSS SSS a a a a a SS SS SS SS Category 1D ZONE 20 HAZARDOUS AREA Internal Vessel Rating Ex Il 1 D IP67 Ta 20 C to 75 C Black Shield SULTAN REMOTE TRANSDUCER kna A e2. marking label g Safe power supply Power supply values must be according to the Specifications h It is advised to provide a cover for the unit to prevent damage that could happen due to environmental conditions 1 Do not put into service where there is a possibility of contact with acetic acid 4 Use The instructions for safe use of the Sultan Unit is as follows 04 Safety Instr v2 ATEX Cati D A20_Sultan doc Page 2 of 7 Hawk Measurement Systems Pty Ltd www hawklevel com a The Sultan equipment must put into service safely see Putting Into Service above b This User Manual must be read and understood by any person involved with the unit c Environment and installation conditions should be checked regularly d When opening the cover of the any Sultan unit prevent dust liquids or chemical substances from getting inside the unit Do not leave any cover open in rain or snow conditions e The LCD display is visible through the clear lid of the AWR series Sultan Remote Electronics enclosure To view the LCD display on the AWI series Sultan Integral Transmitter open the visor by lifting up the front edge with a finger Close and click into place again after viewing so that the display is protected from environmental effects f Before making any wiring or hardware configuration changes it is important to disconnect power from the equipment 5 Assembling and dismantling The only assembly that may be required by the u
3. A higher level of performance Safety instructions x CEs HAWK SULTAN SERIES Smart Universal Level Transmitter And Network A20 ATEX Category 1 D C E0359 x 11 D T85 C Equipment types IP67 AWRT series Remote Transducer T 20 C to 75 C AWR series Remote Electronics ITS04ATEX12896X AWI series Integral Transmitter YV AWST series Smart Transducer 1 General This document provides instructions for the installation of equipment for Category 1 hazardous dust locations according to EC Type Examination Certificate ITTS04ATEX12896X ATEX Categories are relevant in all parts of the European Community Device Category 1D is similar to Zone 20 This equipment can also be installed in Categories 2 and 3 The Hawk Sultan Series Acoustic Wave equipment uses high frequency acoustic waves to measure the distance from the sensor face to the material product surface The equipment is available as an Integral Transmitter or as a Remote system with various levels of Ex rating The Remote Sultan system is one where an AWRT series Sultan Acoustic Wave Remote Transducer is mounted at the level measurement point and an AWR series Sultan Remote Electronics unit is installed some distance away in a more convenient location The AWI series Sultan Acoustic Wave Integral Transmitter models as well as the AWST series Sultan Smart Transducer models consist of a transducer and an electronic control amplifier in a single housing T
4. g right back hinge unlocks to gain access to the cable wiring located under the interior hinged cover flap To close the lid ensure that the double hinge at the top of the enclosure is locked into place before re tightening the lid fastening screw b Sultan Remote Electronics AWR series models To access the user controls unlock the clear cover using the lever on the right hand side of the clear lid Press this lever in the direction of the arrow towards the lid to release the catch The lid can then be swung open to gain access to the user control push buttons Close the lid when finished To lock the lid press on the lower part of the lever which moves the arrow symbol in reverse slightly away from the lid locking the lid closed c Change of output configuration The only other hardware adjustment that may be desired by the user is converting from the Sultan 234 output configuration to the Sultan 2 output configuration Refer to Assembling and Dismantling above d Software Adjustment For software adjustment of Sultan unit parameter adjustment and data entry refer to instructions in Entering Data and all of the Setup sections If GosHawk II software is to be used for parameter adjustment and data entering from a lap top computer read and fully understand the information in the GosHawk IT Manual either supplied with the equipment or downloaded free from the Hawk web site http www hawklevel com The AWST series m
5. hey are mounted directly at the level measurement point usually at the top of a vessel and focused downwards to the product surface The Integral Transmitter includes a user interface keypad and display whereas the Smart Transducer is smaller in size and has no user interface except for the communication port Zz Equipment Identification The ATEX Category 1D marking label is shown above 04 Safety Instr v2 ATEX Cati D A20_Sultan doc Page 1 of 7 Hawk Measurement Systems Pty Ltd www hawklevel com When Hawk Sultan Acoustic Wave equipment is installed and mounted in Category 1 or 2 hazardous areas these User Manual Safety and Operating Instructions the general Ex installation regulations and the general installation regulations for electrical equipment must all be observed The installation of Ex instruments should only be made by trained personnel 3 Putting Into Service To put a Hawk Sultan Unit safely into service the following steps must be taken a To be compliant the equipment must be installed with suitable protection for the cable It must be protected in a suitable manner and terminated in an enclosure suitable for the environment such as a suitably certified EEx e junction box b Follow the instructions in Typical Installations and Installation Guide as well as the relevant conditions on the ATEX EC Type Examination Certificate e Transducer cables shall be appropriately connected e Units with terminal compartme
6. ltan Integral Transducer in Zone 20 Hazardous woa aa THIS DRAWING AND THE CONTENTS THEREOF MEASUREMENT SYSTEMS REPRODUCTION OR DWG NO REVISION SHEET WRITTEN AUTHORISATION FROM HAWK HAW_RD_WIR ATEX J1 A20 1 1 MEASUREMENT IS PROHIBITED 04 Safety Instr v2 ATEX Cati D A20_Sultan doc Page 7 of 7 Hawk Measurement Systems Pty Ltd www hawklevel com
7. nt shall be mounted with the terminal compartment outside the hazardous area e Units shall not be installed where they are subject to direct sunlight c Remote Electronics enclosure conduit entry locations for AWR series models are shown in Dimensions Remote Enclosure Remove the terminal cover by loosening the two captive screws Use a flat blade screwdriver and a slight tap to remove the selected conduit entry openings in the front of the enclosure Follow the installation instructions in the Installation Guide and Wiring Diagram sections Be careful to seal any unused cable glands When wiring is complete ensure the cable glands are securely sealed against the enclosure and the cable then seal the terminal cover by tightening the two screws d Integral Transmitter AWI series models have cable glands located at the rear of the housing which face downward to protect against moisture ingress Ensure that cable glands are securely tightened to adequately seal the cable Be careful to seal any unused cable glands The Smart Transducer model AWST has one cable entry point e Correct wiring Follow the instructions in the Wiring Diagram sections Wiring should be in accordance with relevant installation standards for hazardous area equipment or other local codes of practice f Safe temperature Temperature must not exceed the operating range of the Sultan unit In particular Ex rated equipment must not exceed the temperature limits shown on the
8. odels with no buttons can only be adjusted in this way 8 Application Conditions a Voltage Supply Must be according to the voltage supplies given in Specifications b Temperature Must not exceed the operating temperature range stated in Putting Into Service above To prevent inaccuracies due to extremes in temperature and the effect of long term UV exposure it is recommended that transducers constructed with grey beige polypropylene housing material be protected from direct sunlight This does not apply to the blue green and dark grey plastic enclosure parts These parts have better UV stability 04 Safety Instr v2 ATEX Cati D A20_Sultan doc Page 4 of 7 Hawk Measurement Systems Pty Ltd www hawklevel com c Cable Connection Cables must only be replaced by the same cable type If extending the cable it must be protected in a junction box and terminated in an enclosure suitable for the environment Refer to Wiring Diagrams Transducer d Earthing Hawk Sultan Acoustic Wave equipment must be earthed to ensure that shielded cabling is effective e Electrostatic Discharge Hawk Sultan Acoustic Wave equipment has been certified safe to use in hazardous dust locations f Industrial Conditions This equipment is designed for use in normal industrial conditions relating to humidity vibration etc If the user intends to operate the equipment in more severe environmental conditions the manufacturer or local distributor should
9. r A S a a Wiring to conform to EN 61241 14 Related Drawing No modifications permitted without the approval of the Engineering Manager DOC NO NOT TO SCALE ALL DIMENSIONS IN MM COMPANY PETET HAWK MEASUREMENT SYSTEMS 15 17 MAURICE COURT NUNAWADING DATE 49 12 2011 VICTORIA AUSTRALIA 3131 amp Remote Transducer in Zone 20 Hazardous Area DWG NO REVISION SHEET HAW_RD_WIR ATEX H1 A20 1 1 A01 TITLE Wiring for ATEX Category 1 D Sultan 3 amp 4 wire Remote Amplifier in Safe Zone THIS DRAWING AND THE CONTENTS THEREOF ARE THE PROPRIETARY PROPERTY OF HAWK MEASUREMENT SYSTEMS REPRODUCTION OR USE OF THIS INFORMATION WITHOUT PRIOR WRITTEN AUTHORISATION FROM HAWK MEASUREMENT IS PROHIBITED Page 6 of 7 Hawk Measurement Systems Pty Ltd www hawklevel com J1 Wiring for ATEX Category 1 D Sultan Integral Transducer in Zone 20 Hazardous Area Note All equipment in Zone 20 Hazardous area must have ATEX Cat 1 D marking Certificate No ITSO4ATEX12896X ATEX Rating x 113 1D External Environment Rating Zone 2 22 ATEX Category 2 or Safe Area Note 1 Wiring to conform to EN 61241 14 Related Drawing No modifications permitted without the approval of the Engineering Manager DOC NO NOT TO SCALE ALL DIMENSIONS IN MM COMPANY HAWK MEASUREMENT SYSTEMS 15 17 MAURICE COURT NUNAWADING DATE 49 12 2011 VICTORIA AUSTRALIA 3131 a ge WES PATE 20 12 2011 ee Wiring for ATEX Category 1 D Su
10. ser is to reconfigure a Sultan 234 unit 2 3 4 wire Operation to that of a Sultan 2 unit 2 wire operation This flexibility is unique to Sultan equipment To safely reconfigure a Sultan 234 model to that of a Sultan 2 model a Make sure that the original unit is a Sultan 234 model eg AWI234 or AWR234 It is not possible to reconfigure a Sultan 2 model eg AWI2 or AWR2 as a Sultan 234 model Only Sultan 234 models can be reconfigured to operate as Sultan 2 models and this modification is reversible b Disconnect the power to the Sultan 234 Unit c Todo the modification follow the instructions in Wiring Change Sultan 234 lt gt Sultan 2 d Modify the wiring to suit the new output configuration as shown in Wiring Diagrams 6 Installation and Wiring Carefully follow Typical Installations Installation Guide and Wiring Diagram sections Follow all points listed in Putting Into Service above Wiring should be in accordance with relevant installation standards for hazardous area equipment eg EN 61241 14 or other local codes of practice 04 Safety Instr v2 ATEX Cati D A20_Sultan doc Page 3 of 7 Hawk Measurement Systems Pty Ltd www hawklevel com 7 Adjustment a Sultan Integral A WI series models To access the user controls loosen the single captive screw sufficiently to release the lid The lid can then be raised to one of two positions 1 vertical 2 swun
Download Pdf Manuals
Related Search