Challenger10 Installation and Quick Programming Manual
Contents
1. 2 2 l g TERM link off iw 1 Do lt RAS without earth terminal P 5 le 4 1g l y TERM link off Extemal power supply z if needed a 3 ay O LAN Earth Data gathering panel last device on LAN Z Power Earth 6 TERM link on F F Challenger10 Installation and Quick Programming Manual Figure 1 legend Item Description 1 RS 485 LAN cable We recommend the use of 2 pair twisted shielded data cable such as Belden 8723 for optimal performance 2 Join data cable shields where cable extends past a device that doesn t have a LAN earth connection 3 In each segment of LAN cabling connect one end only of the data cable shield toa device s LAN earth terminal 4 External 12 VDC power supply if needed 5 Do not connect the from the external 12 VDC power supply to the of the LAN 6 Terminate the control panel and the most distant device or the devices at the ends of the two longest LAN cable runs as applicable System configurations A Challenger system s RS 485 LANs LAN 1 or LAN 2 may be configured in a variety of ways e Straight LAN where the Challenger panel is at one end of a LAN cable run e Star LAN where multiple LAN cable runs are used in a branched configuration e Multi building where the LAN extends to more than one building LAN 1 is required and LAN 2 is optional Each LAN must be indepen2. Normally open 10K Normally closed tamper contact tamper contact 10K L s Normally closed Normally open alarm contact alarm contact The panel uses the circuit s resistance to determine the state of the zone input e 10 KQ indicates sealed e Open circuit or short circuit indicates unsealed To use two state monitoring for all zone inputs Input Tamper Monitoring must be set to No Install menu option 7 System Options Note When the system is used in 2 state configuration inputs can only report sealed and unsealed states This prohibits the use of input types that need to detect short or open states See the Challenger10 Programming Manual for details Special zone input types Zone inputs programmed as area control type inputs can also be used to turn areas on and off as opposed to entering a PIN on a keypad These inputs do not have areas assigned to them their functions are determined by assigning an alarm group to them 16 Challenger10 Installation and Quick Programming Manual Figure 9 Wiring of key switches for input types 6 and 31 1c c2c3cC 4c5C6C 7C8C9C 10011C12C 13C14C15C 16C SHOOOG HOHOHODO BHHSHHH HHHHGH HHOHOHHOOD Not used with two state monitoring 10K 10K 10K 10K e Normally closed Normally open key switch contact key switch contact Input type 6 is used for
3. Install menu option Description 1 Input Database 2 Area Database 3 RAS Database 4 DGP Database 5 Alarm Groups 6 Timers 22 Program all physical inputs on the control panel DGP or plug in expander and inputs that are activated by macros The default values for inputs 1 to 16 are e Input type is set to type 2 Secure Alarm e Report ID type is set to 25 140 General Alarm e Siren event flag is selected Event flag 2 Secure Alarm is selected and is mapped to relay 2 Strobe Output Program up to 99 areas Areas determine how the system is partitioned and therefore provides the ability to limit users to performing functions only in the areas relevant to their role The default values for areas are e Exit time is set to 60 seconds e Entry time is set to 30 seconds e Siren event flag is set to 1 Program the system s remote arming stations RASs RASs provide alarm system control such as area arming or disarming and provide access control such as unlocking a door for a user You may need to change the RAS s default area LED assignments RAS 1 is programmed as an LCD RAS to be polled and is assigned Alarm Group 2 Master RAS Program any data gathering panels DGPs used to send information to the control panel and to provide added access control functionality Program alarm groups to enable users inputs and arming stations to control the system s alarm control functionality Pr
4. 8 Click to select the Search for the best driver in these locations radio button and then browse to include the location of the Tecom Firmware Loader application in the search for example C Program Files Tecom Firmware Loader inf_driver 9 Run Tecom Firmware Loader for example double click the file C Program Files Tecom Firmware Loader tecom fw loader_v1 04 exe When you run it will tell you if the device is ready otherwise you can t select a file 10 Click Select File and then browse to the location of the firmware upgrade file on your computer Select the file and then click Open 11 Click Program File to update the panel firmware The process will take several minutes The percentage completion displays at the bottom of the window When finished a Programming is complete message displays 12 Remove the USB cable from the Challenger panel 13 Disconnect the panel s power supply 14 Remove test links 1 and 2 Figure 5 on page 11 item 22 15 If applicable reconnect the panel s Ethernet and or serial connections to the management software computer 16 Reconnect power to the panel The panel should reboot and connect with RAS 1 on LAN 1 If the panel does not reboot repeat the process from step 9 17 Use Install menu option 11 Version option 1 to display the Challenger version number It should display the new version number 18 We recommend that you also default the panel s programmin
5. 26 to 41 can be programmed to be valid when a relay is active and invalid at other times Display the number of errors detected in communications between the control panel and the devices connected to the control panel Download access control data for Intelligent Access Controllers 4 door or 4 lift DGPs that may not have been downloaded automatically Display the site number and ID number of the last card read by a reader connected directly to the control panel doors 1 to 16 on LAN 1 and doors 65 to 80 on LAN 2 Challenger10 Installation and Quick Programming Manual 23 Install menu option Description 26 Diagnostics Skip this option It is reserved for factory use 28 Remote Controllers Use this option to access additional programming menus for remote devices such as a RAS an Intelligent Access Controller DGP or a TS0862 Smart Door Controller which is addressed and polled as a RAS 29 Panel Volts amp Display the values of the panel s voltage and current consumption Currents 31 Battery Testing Program automatic battery testing or perform manual battery testing 32 Custom Message Create a custom message or use the panel s time and date for the top line of the RAS s initial LCD screen 33 Program Next Program the date of the next service call and a custom message on Service the LCD to call the installer 34 Program Summary Program event flags to be triggered on system wide events such as Event Flags ma
6. a device connected to J15 serial port On solid when J15 is ready inactive 18 Challenger10 Installation and Quick Programming Manual Rx0 item 19 flashes to indicate data being received from device connected to J15 serial port Tx1 item 24 flashes to indicate the Challenger panel is polling remote units RASs and DGPs on LAN 1 The Tx1 LED should always be active Rx1 item 24 flashes to indicate remote units on LAN 1 are replying to polling Tx2 item 26 flashes to indicate the Challenger panel is polling remote units RASs and DGPs on LAN 2 Tx2 flashes quickly for 1 second each minute when nothing is polled on LAN 2 Rx2 item 26 flashes to indicate remote units on LAN 2 are replying to polling Link active item 17 flashes when Ethernet is active 100BT item 15 on when Ethernet speed is 100 Mbps Challenger10 Installation and Quick Programming Manual Initial programming This section describes basic initial programming via a RAS Advanced programming is typically performed via management software such as Titan Security Commander or Forcefield so basic programming also includes the items required to connect with a management software computer Refer to the documentation provided with the management software for additional details Challenger panel programming is described in detail in Challenger10 Programming Manual This section describes the following programming steps that are part of the installatio
7. the Port field and select USB as the communications mode Save the record 1 Select Open System from the File menu select Active System and then save the record The connection indicator at the bottom of the Titan window displays green to indicate a successful connection Example 2 Programming an event driven IP connection to a Titan computer You may use a Cat 5 cable to connect the Challenger panel to a Titan computer either directly or via LAN Challenger10 Installation and Quick Programming Manual 29 To establish an event driven IP connection 1 On an LCD RAS access the Install menu See Accessing the Challenger menu on page 20 2 Press 9 ENTER to access the Communications menu and then select option 1 Setup H W to access the Setup menu 3 Select option 1 Onboard and then press ENTER to step through the options Change the default settings if required in particular change Ethernet to Yes Use the values advised by the site s network administrator for the IP address subnet mask and gateway address 4 When returned to the Setup menu press 0 ENTER to exit to the Communications menu 5 At the Communications menu select option 2 Setup Paths and then press 3 ENTER to select path 3 MANAGEMENT SOFT 6 Press ENTER to display the first item for path 3 and then select option 1 Main 7 Press ENTER to step through the options and change the default settings if req
8. to be aware of requirements for cabling and earthing and plan accordingly NOTICE A qualified service person complying with all applicable codes should perform all required hardware installation Disclaimer This manual contains recommendations based on Australia and New Zealand codes It is not an authoritative reference regarding codes and has not been reviewed by the responsible authorities The codes may change and may not be reflected in this document Cabling requirements This section contains recommendations for installers and electricians for the application and wiring of Challenger equipment with respect to e System earthing e RS 485 data cable LAN cabling e Power supply from LAN or from external 12 V supply System earthing The following recommendations are based upon Australian wiring regulations AS NZS 3000 2000 Section 5 e Each device s GND link if applicable must be removed e Connect the 230 16 VAC plug pack earth conductor to the Challenger panel s earth terminal Figure 5 on page 11 item 3 Do not extend this wire to any device outside of the enclosure e Some Challenger devices have an earth lug or stud on the PCB and are fitted with a link labelled GND or EARTH In such cases the device s GND or EARTH link must be removed When configured correctly there will be a resistance value greater than 100 kQ between the device s earth lug or stud or power earth terminal similar to
9. 17 Telephone connection See Figure 5 on page 11 item 13 The Challenger panel is supplied with a pre wired 604 plug for connection to a 611 socket for PSTN in connection mode 3 for dialler reporting formats see Figure 11 below Figure 11 Line connections for 611 socket for dialler reporting formats O1 2 o3 Pins 2 and 6 O4 to telephones on premises EES x O2 Pins 2 and 6 7 611 ki 604 plug connected se to Challenger panel AA to PSTN 05 a o6 J Comms earth Connection mode 3 J15 serial port See Figure 5 on page 11 item 20 The J15 port also called STU port may be used for connection to a management software computer or to a printer Figure 12 below details the required connections from the J15 terminals to either a DB9 or a DB25 serial connector to a management software computer Figure 12 Wiring details for computer connection J 15 on Challenger PCB Computer serial port 412 DB9 pins DB25 pins Rx gt TX 3 2 Tx gt Rx 2 3 OV gt GND 5 T LED indications Refer to Figure 5 on page 11 e L1 item 23 flashes slowly to indicate normal panel operation and flashes quickly during reset mode Clearing the memory via the Challenger panel PCB on page 24 or firmware update Firmware upgrade process on page 32 e TXO item 19 flashes to indicate data being sent from the Challenger to
10. Figure 5 on page 11 item 3 and any C or OV terminal on the device e Install LAN isolation devices between multiple buildings and maintain independent earthing systems For example use TS0893 TS0894 or TS0896 Isolation Interface modules to provide electrical isolation and or to extend distance Earthing of one cabinet containing several devices All devices designed for the system have earth connections via metal studs to the metal housing Take care that these metal studs have a good connection to bare metal no paint 2 Challenger10 Installation and Quick Programming Manual Earthing of panels in a single building In a single building several cabinets or devices are earthed A licensed electrician should check the integrity of the building earth system Earthing of panels in more than one building If the wiring extends to separate buildings use more than one common earth system Install LAN isolation devices such as TS0893 to isolate the system LAN between buildings to protect the system against differences in earth potential See Figure 3 on page 7 Guidelines for retrofitting a Challenger V8 system When replacing a Challenger V8 panel with a Challenger10 panel in an existing installation e Where used a device s GND or EARTH link must be removed if fitted Note Challenger10 panels do not have a GND link e Where 230 16 VAC plug packs are used connect the earth conductor to the device s power earth term
11. S tecom Challenger10 Installation and Quick Programming Manual P N MAINST TS1016 REV 01 ISS 18FEB13 Copyright Trademarks and patents Manufacturer Agency compliance Contact information 2013 UTC Fire amp Security All rights reserved The Challenger name and logo are trademarks of UTC Fire amp Security Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products Interlogix a division of UTC Fire amp Security Australia Pty Ltd Level 1 271 273 Wellington Road Mulgrave VIC 3170 Australia N4131 A For contact information see www interlogix com au Content Important information ii Agency compliance ii Limitation of liability ii Regulatory requirements for New Zealand iii Preface iv Product overview 1 Product contents 1 Before you begin 2 Cabling requirements 2 System configurations 6 Installing the control panel 9 Installation guidelines 9 Installation procedures 10 Connections 11 LED indications 18 Initial programming 20 Disarming the system 20 Accessing the Challenger menu 20 Clearing the memory 24 Basic programming sequence 25 Working with multi area systems 26 Default installer PIN 26 Enabling communications 27 Programming users 31 Firmware upgrade process 32 Requirements 32 Getting ready 32 Upgrade process 32 Challenger10 Installation and Quick Programming Manual Import
12. Type B Mini Male to connect the Challenger panel to a Titan computer This process requires Titan 3 0 or later Note Do not connect the USB cable until instructed to To establish a polled USB connection 1 On an LCD RAS access the Install menu See Accessing the Challenger menu on page 20 2 Press 9 ENTER to access the Communications menu select option 2 Setup Paths and then press 2 ENTER to select path 2 USB INSTALLER 3 Press ENTER to display the first item and then select option 1 Path Main The first option displays 4 Press ENTER to step through the options and change the default settings if required in particular change Enabled to Yes You might also need to change the account code and the computer password default is 0000000000 5 Press 0 ENTER as needed to exit from the Communications menu 6 In Titan select Ports from the Admin menu 7 Inthe port record select USB and then enter a port number and description Save the record 8 Connect the Challenger panel s USB port at J18 Figure 5 on page 11 item 18 to a USB port on the computer via a USB cable The first time you connect a Challenger panel to the computer s USB port the Found New Hardware Wizard may display Do not use the Wizard 9 Select Challenger from the Admin menu 1 oO In the Challenger record ensure the Challenger No and Security Password are the same as programmed via RAS type the port number in
13. able or to the public telephone network Challenger10 Installation and Quick Programming Manual 9 The general installation guidelines are as follows e Mount the unit using screws or bolts through the four mounting holes in the base Ensure that the unit is mounted on a flat solid vertical surface so that the base will not flex or warp when the mounting screws or bolts are tightened e Allow 50 mm clearance between the equipment enclosures mounted side by side and 25 mm between the enclosure and any side wall or ceiling e The Challenger panel is powered and earthed via a 16 Volt AC plug pack supplied A power outlet GPO must be in proximity to the panel Only qualified Electricians should provide a GPO e The Challenger panel has an onboard dialler Telephone connections must be in proximity to the panel Only ACMA Cablers should provide telephone cabling e If the upper and or lower cabinet entry cable holes are used to route wiring into the control panel always use a proper pipe fitting system by means of an appropriate conduit and junction box For this purpose use only materials of suitable flammability class e Avoid loops of wire inside the control panel cabinet and route cables so that they do not lie on top or underneath the printed circuit board The use of cable ties is recommended and improves neatness of the wiring within the box e The battery used with this unit must be made of materials of suitable flammabilit
14. ant information Agency compliance This product conforms to the standards set by Standards Australia on behalf of the Australian Communications and Media Authority ACMA UTC Fire amp Security recommend enclosure covers remain fitted to maintain C Tick compliance Limitation of liability To the maximum extent permitted by applicable law in no event will Interlogix a division of UTC Fire amp Security Australia Pty Ltd be liable for any lost profits or business opportunities loss of use business interruption loss of data or any other indirect special incidental or consequential damages under any theory of liability whether based in contract tort negligence product liability or otherwise Because some jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages the preceding limitation may not apply to you In any event the total liability of Interlogix shall not exceed the purchase price of the product The foregoing limitation will apply to the maximum extent permitted by applicable law regardless of whether Interlogix has been advised of the possibility of such damages and regardless of whether any remedy fails of its essential purpose Installation in accordance with this manual applicable codes and the instructions of the authority having jurisdiction is mandatory While every precaution has been taken during the preparation of this manual to ensure the accuracy of its con
15. ault installer PIN on page 27 and for defaulting the panel Clearing the memory via the Challenger panel PCB on page 24 12 Challenger10 Installation and Quick Programming Manual Item Description 23 LED 1 flashes slowly to indicate panel operation and flashes quickly during firmware update or panel default 24 Transmit and receive LEDs to indicate activity on LAN 1 See LED indications on page 18 25 TERM link for LAN 1 See Terminating the RS 485 LAN on page 14 26 Transmit and receive LEDs to indicate activity on LAN 2 See LED indications on page 18 27 TERM link for LAN 2 See Terminating the RS 485 LAN on page 14 See Figure 6 below for connection details for terminal blocks J1 to J5 Figure 6 Connection details for terminal blocks J1 to J5 4 fo 16 VAC plug pack ye lele Plug pack earth wire Teo 12 V battery 1 5 jo J le E S M 9 Auxiliary power 12 VDC leo g WAO Gii m Auxiliary power 12 VDC a WAE Pe B Qo 5 LAN 1 required Z 8o RS 485 data cable 59 ele e e Z Panel tamper switch i mei 50 e Extemal 8 Q siren speaker me AO 5 or 1KQ 1 4 watt resistor A AO Intemal 8 Q siren speaker z 2 o ano 12 V s
16. dently configured and terminated Straight LAN In a straight configuration Figure 1 on page 5 the Challenger panel is at one end of the LAN cable run and all other devices are connected to the LAN cable The TERM links would be on for the Challenger panel and for the last device on the LAN Star LAN In a star configuration the LAN has at least two branches Figure 2 on page 7 optionally connected via a TS0844 Power Distribution Board see TS0844 Power Distribution Board on page 8 The TERM links would be on for the two devices at the ends of the two longest cable runs Note A star LAN configuration may consist of a number of cable runs branches LAN termination should be set to ON only at the devices at the far ends of the two longest branches A star LAN that has multiple branches in excess of 100 m may need to use LAN isolation devices such as TS0893 LAN Isolation Interface modules to isolate the LAN segments that do not have LAN termination set to ON 6 Challenger10 Installation and Quick Programming Manual Figure 2 Star LAN configuration T Off Challenger panel T On termination link fitted T Off termination link not fitted T Off Multi building or long distance LAN cabling If the RS 485 LAN extends to more than one building each building must have its own earth system LAN isolation devices such as TS0893 LAN Isolation Interface modules are used to isolate the system LAN be
17. details 7 Program the required system options via Install menu option 7 System Options if the default values are not suitable see Table 2 on page 22 8 Program custom site specific words if needed via Install menu option 10 Text Words 9 Program holidays in User menu option 21 Holidays Holidays must also be assigned one or more holiday types 1 to 8 Decide what each holiday type will be used for and record the purpose in the Holidays and Holidays Types worksheets see the Challenger10 Administrators Manual 10 Program time zones via Install menu option 13 Time Zones 11 Program areas via Install menu option 2 Area Database 12 Program area groups via Install menu option 36 Area Groups to help manage areas See also Working with multi area systems on page 26 Challenger10 Installation and Quick Programming Manual 25 13 Program alarm groups via Install menu option 5 Alarm Groups 14 If your system requires more than 16 inputs or requires advanced access control functionality then you will need to program DGPs data gathering panels into the system Program DGPs via Install menu option 4 DGP Database 15 Program inputs via Install menu option 1 Input Database 16 If your system requires more than 1 arming station then you will need to program RASs via Install menu option 3 RAS Database 17 Program the system s timers via Install menu option 6 Timers if the default values are not suitable see Table 2 o
18. er LAN data to be carried over an IP network and to be converted back to RS 485 communications for connection to LAN devices Refer to the Interlogix Web site at www interlogix com au for details and images of LAN devices Challenger10 Installation and Quick Programming Manual Installing the control panel See Figure 4 below for overall details of a TS1016 Challenger panel installed in a TS0307 Universal Enclosure Figure 4 Challenger panel board mounted in enclosure 1 2 lt l S I TS1016 board ha ebeL OOCoOO DOOOoO eL see serce Oo o m o mj 00 o oO o m 00 o 0 00 00 O 0 00 o o Oo oO O Oo oO Oo oO D o oO QO m 00 0 0 oO oO m O00 0 00 Space for 12 V 7 Ah battery o not included l 1 LO S on Figure 4 legend Item Description 1 Enclosure mounting points 2 Board mounting points 3 Location of tamper switch Installation guidelines Challenger panels are designed assembled and tested to meet the requirements related to safety emission and immunity with respect to environmental electrical and electromagnetic interference as of current relevant standards In addition to the general installation guidelines installers must adhere to any country dependent requirements of local applicable standards Only a qualified electrician or other suitably trained and qualified person should attempt to wire this system to mains power if applic
19. evices may be used to provide electrical isolation and to reduce cabling costs LAN isolation devices can also be used to extend the distance of LAN cabling beyond what can be achieved by a single cable run of 1 5 km LAN devices include the following TS0844 Power Distribution Board The TS0844 module can be used in either data or power mode as set by a pair of onboard links The TS0844 module expands the number of physical connections that can be made to the panel s power or data output terminals e In data mode each TS0844 module provides five sets of LAN out connections and five sets of and auxiliary power output terminals e In power mode each TS0844 module provides 10 sets of and auxiliary power output terminals A TS0844 module is shown in Figure 2 on page 7 TS0893 LAN Isolation Interface Provides an optical isolation barrier between components on a Challenger or Intelligent Access Controller LAN The TS0893 can be also used as a LAN repeater with up to three stages cascaded together to increase the maximum LAN cabling run from 1 5 km to 6 km TS0893 modules are shown in Figure 3 on page 7 TS0896 RS 485 to Fibre Optic Interface A pair of TS0896 modules with suitable optical fibre cable may be used to extend the LAN to remote buildings or locations within a building for example where unused optical fibre cable already exists TS0098 Challenger IP LAN Adaptor Multiple IP LAN Adaptor modules enable Challeng
20. g From the Install menu option 14 Defaults press 99 ENTER to reset all custom programming Challenger10 Installation and Quick Programming Manual 33
21. g ready You will need to backup or record any custom programming that you want to use after upgrading the firmware Upload the Challenger panel s database to the management software computer After updating the firmware you will need to reprogram the connection details before you can download the Challenger panel s database Upgrade process To upgrade the Challenger panel firmware 1 Disconnect the panel s power supply 2 We recommend that you disconnect the panel s existing Ethernet and or serial connections to the management software computer for the duration of this process 3 Fit test links 1 and 2 Figure 5 on page 11 item 22 4 Reconnect power to the panel LED L1 will blink rapidly Figure 5 on page 11 item 23 5 Use the USB cable to connect the computer to the Challenger panel s USB port at J18 Figure 5 on page 11 item 18 32 Challenger10 Installation and Quick Programming Manual The first time you connect a Challenger panel to the computer s USB port the Found New Hardware Wizard may display If the Found New Hardware Wizard does not display go directly to step 9 6 If the wizard asks Can Windows connect to Windows Update to search for software click to select the No not this time radio button and then click Next 7 Ifthe wizard asks What do you want the wizard to do click to select the Install from a list or specific location radio button and then click Next
22. hallenger10 Installation and Quick Programming Manual is for installation technicians to install a Challenger panel e The Challenger10 Users Manual is suitable for most users of the Challenger10 system to perform everyday tasks e The Challenger10 Administrators Manual is for users and system administrators who need to manage the Challenger10 system via its text based user interface e The Challenger10 Programmers Manual is for system administrators and installers who need to manage the Challenger10 system via its text based user interface in particular the Install menu This manual describes e How to install a Challenger panel e How to connect other equipment to the Challenger panel e Challenger programming required for basic system setup This manual is intended for use only by trained Challenger installation and configuration technicians Notes e The permissions assigned to you may not allow you to do everything described in this manual You may not be able to see all menu items described in this manual e A qualified service person complying with all applicable codes should perform all required hardware installation iv Challenger10 Installation and Quick Programming Manual Product overview Challenger is a scalable intrusion detection and access control system Challenger panels use one and optionally a second RS 485 data bus LAN to provide continuous polling of remote arming stations RAS and data gathe
23. hout Install menu access 1 Remove power to the Challenger panel 2 Fit test link 1 Figure 5 on page 11 item 22 and repower the system L1 item 23 illuminates for about 20 seconds flashes quickly for about 20 seconds to indicate reset mode and then flashes slowly to indicate normal mode Note The panel can only be defaulted in the 20 second interval when L1 is flashing quickly in reset mode The panel returns to normal mode automatically to help protect against accidental reset 3 Remove test link 1 when L1 is flashing quickly to default the panel Basic programming sequence This section provides an overview of how to use an LCD RAS to set up a basic alarm system that uses PINs for access control To initially program a Challenger system Plan the system and fill out the programming sheets Disarm the system See Disarming the system on page 20 Access the Install menu See Accessing the Challenger menu on page 20 Default the system See Clearing the memory on page 24 Disarm the system and access the Install menu again as described above Program the date and time via User menu option 15 Time and Date na A A WB DY Change the default installer PIN See Changing the default installer PIN on page 26 5 If the system will contain more than areas 1 to 16 then modify Area Group 1 using Install menu option 36 Area Groups See Working with multi area systems on page 26 for
24. inal similar to Figure 5 on page 11 item 3 e Connect one end only of the RS 485 data cable shield to a device s LAN earth terminal or earth lug similar to Figure 5 on page 11 item 1 e All other wiring compliant with Challenger V8 earthing recommendations via Communications Earth Terminal CET may remain unchanged Guidelines for new Challenger10 installations When installing a Challenger10 panel in a new installation follow the wiring requirements of this manual including e Where used a device s GND or EARTH link must be removed if fitted Note Challenger10 panels do not have a GND link e Where 230 16 VAC plug packs are used connect the earth conductor to the device s power earth terminal similar to Figure 5 on page 11 item 3 e Connect one end only of the RS 485 data cable shield to a device s LAN earth terminal or earth lug similar to Figure 5 on page 11 item 1 e Connections to building earth via CET are no longer required Note For new installations the earthing and configuration instructions in this manual supersede all previously released installation instructions supplied with other devices unless otherwise noted RS 485 LAN cabling The cabling recommendations for the two RS 485 system LANs are e Use 2 pair twisted shielded data cable such as Belden 8723 e In each segment of LAN cabling connect one end only of the data cable shield to a device s LAN earth terminal Join data cable shields
25. ins failures or DGPs going offline 35 Program Macro Logic Program macro logic equations for activating inputs or event flags based on the conditions of one to four macro inputs event flags or relays 36 Area Groups Area groups include one or more areas that can be more easily managed for example armed or disarmed simultaneously Each area in an area group must be configured to allow certain users as specified by the user s alarm group to have permissions for arming disarming alarm reset and for timing Clearing the memory When installing a new panel or upgrading the firmware on an existing panel we recommend that you default the panel before programming it Note All custom programming will be erased Back up any data you need before using these procedures The panel can be defaulted in two ways see e Clearing the memory via RAS below or e Clearing the memory via the Challenger panel PCB below Clearing the memory via RAS Users with access to Install menu option 14 Defaults can clear the memory via RAS To clear the panel s memory via RAS 1 From the Install menu option 14 Defaults press 99 ENTER to reset all custom programming Clearing the memory via the Challenger panel PCB You may want to perform a panel default to reset the panel to its factory default state and erase all programming 24 Challenger10 Installation and Quick Programming Manual To clear the panel s memory wit
26. ion 3 Connect the plug pack earth wire green to the power earth terminal 4 Connect the and terminals to a 12 V sealed lead acid battery 7 0 An maximum not supplied 5 Connect the and auxiliary power output terminals to devices that require 12 Volt DC power such as detectors See Auxiliary power terminals on page 14 6 Connect the D and D terminals to the RS 485 data cable for LAN 1 If the and terminals are used consider the current draw as part of the auxiliary power output See Auxiliary power terminals on page 14 7 Input and common terminals for panel tamper switch supplied Short circuit for sealed open circuit for unsealed Must be sealed if not used Can only be used with normally closed contacts such as the panel tamper switches 8 Connect the S and S terminals to an external 8 Q siren speaker If an external siren is not used connect the S and S terminals to a 1K 1 4 watt resistor supplied The maximum current draw for the external 8 Q siren and the strobe is 700 mA The internal and external siren speaker outputs are relay 16 and are mapped to event flag 1 9 Connect the S and S terminals to an internal 8 Q siren speaker If an internal siren is used consider the current draw as part of the auxiliary power output See Auxiliary power terminals on page 14 10 Connect the and terminals to the strobe The maximum current draw for the external 8 Q siren and the strobe
27. is 700 mA The strobe output is relay 2 and is mapped to event flag 2 11 Connect the D and D terminals to the RS 485 data cable for LAN 2 if required If the and terminals are used consider the current draw as part of the auxiliary power output See Auxiliary power terminals on page 14 12 Zone input terminals See Zone inputs on page 15 13 RJ 12 socket to telephone system dialler See Telephone connection on page 18 14 Slot for SD card 15 100BT LED on when Ethernet speed is 100 Mbps See LED indications on page 18 16 Ethernet port 17 Link Active LED flashes to indicate Ethernet activity See LED indications on page 18 18 USB port 19 Transmit and receive LEDs to indicate data transfer over J15 serial port See LED indications on page 18 20 J15 terminals also called STU port for RS 232 serial connection to computer See J15 serial port on page 18 21 J14 10 way cable socket for TS0840 TS0841 or TS0842 relay or output expansion modules Note The J14 connector can provide power to one relay controller If connected to a device that will be powered from an auxiliary power supply not powered by the Challenger panel then you must ensure that the 12V wire is not connected 22 Test links 1 and 2 Both links are used when updating firmware see Firmware upgrade process on page 32 Link 1 is used when resetting the master installer code Restoring the def
28. llenger10 panels have a range of communications options configured via Install menu 9 Communications The first two options in the Communications menu are e 1 Setup H W This option is used to configure the communications ports on the panel onboard and on expander modules pending e 2 Setup Paths This option is used to configure up to 10 communication paths for connecting to various devices such as a management software computer or a local printer Ten communication paths are available for simultaneous management software connections reporting via onboard dialler printing events and so on The status of each path can be quickly displayed via RAS to facilitate installation and troubleshooting Challenger10 Installation and Quick Programming Manual 27 A communication path can be assigned a priority number in the range 1 to 10 the highest priority being 1 or O for no priority assignment Also a communication path can be designated as a backup to another communication path A Challenger10 panel has default values programmed for the following communications paths e Path 1 CID Dialler For reporting to a remote monitoring company via a telephone connection e Path 2 USB Installer For USB serial connection to a computer running management software such as Titan e Path 3 Management Software For IP connection to a computer running management software such as Titan e Path 10 Service Enabled for management sof
29. ming adding the system s users yourself you will need to program at least one administrator who will be able to program additional users See Challenger10 Administrators Manual for details The default values for User 50 the master code are Name TECOM Master PIN 4346 Alarm Group 3 contains areas 1 to 16 as defined by Area Group 1 Door Group 1 Floor Group 1 Note You may need to add areas to Area Group 1 See Working with multi area systems on page 26 Challenger10 Installation and Quick Programming Manual 31 Firmware upgrade process This section describes how to upgrade Challenger10 panel firmware It is provided here as an interim guide only and is subject to change Note During the upgrade process the Challenger panel will not be able to receive or report alarm signals We recommend that you follow the general instructions listed in the Challenger10 Programming Manual Recommended routine maintenance procedures in particular to notify the alarm monitoring company and personnel on the premises if applicable Requirements To upgrade the firmware you need the following e A powered and functioning Challenger10 panel e A Windows PC with a USB 2 0 port e Tecom Firmware Loader application e Access to the Challenger10 panel s printed circuit board PCB e A USB cable Type A Male to Type B Mini Male to connect the Windows computer to the Challenger panel s PCB e Firmware upgrade file Gettin
30. momentary area control e 10 kQ normal state of key switch indicates sealed e 5kQ or 20 kQ indicates unsealed the programmed alarm group functions are performed Input type 31 is used for toggling area control When the input switches to unsealed the areas secure When the input seals the areas are in access e 10 KQ normal state of key switch indicates sealed turn areas off 5kQ or 20 kQ indicates unsealed turn areas on Figure 10 Wiring of key switch and alarm contact for input type 33 1c 2c3cC 4c5C6C 7C8C9C 10C11C12C 13C14C15C 16C SSOSSOSSOS HHHHH SHSHSHSHSH HHSHHH SBHHHHH OO Normally open o alarm contact H Normally open 10K alarm contact 10K 10K 10K e Normally closed Normally open key switch contact key switch contact Input type 33 24 hour alarm amp isolate input is used to wire a key switch and an alarm contact to the same input For example a key switch used to isolate a shop s input in a shopping centre where only one input is available for each shop Alarm is generated when input changes from sealed to open or short e 10 KQ normal state of key switch indicates sealed e 5 kQO or 20 kQ indicates unsealed isolated no alarm generated e Open circuit generates a tamper alarm e Short circuit generates an alarm Challenger10 Installation and Quick Programming Manual
31. mount them to the board Connections See Figure 5 below for the locations of connectors and other items See Cabling requirements on page 2 for recommendations for the application and wiring of Challenger equipment Figure 5 Challenger10 board details E O O Oj D re E 3 p HF 13 LE e 22 A TAON 5 3 e E xpander 1 Expander 2 Expander 3 1 4 3 He ollo 15 ile So o BBS 24 2 le 16 6 ag 25 17 7 i p 8 8e SF na oz g 2 g 7 19 1 A Vi A E E i de ole olo an 11 20 f pro J8 21 oToTeTeTeto Fal aaa Ea 1 2C3C 4C5C6C 7C8B8CI9C WCNC12C 13C 14C015C 16C 9 ALARM INPUTS 12 Figure 5 legend Item Description 1 Connect one end of each LAN cable shield to the ring terminal and fasten with M3 screw to the Challenger panel board s LAN earth terminal 2 Connect the power terminals to a 16 Volt AC plug pack Maximum current drawn by the panel with no peripheral devices connected is approximately 200 mA Challenger10 Installation and Quick Programming Manual 11 Item Descript
32. n page 22 18 Program the communication options to enable the Challenger system to report alarms to the remote monitoring station via Install menu option 9 Communications 19 Program the behaviour of relays via Install menu option 16 Map Relays 20 Program at least the first user See Programming users on page 31 Working with multi area systems Challenger10 can have up to 99 areas New or defaulted Challenger panels can arm and disarm only areas 1 to 16 This functionality is accomplished via Area Group 1 which contains areas 1 to 16 Area Group 1 is used in the following Alarm Groups e Alarm Group 2 Master RAS or Door e Alarm Group 3 Master Code Installer e Alarm Group 11 High Level User Master e Alarm Group 12 Low Level User Master e Alarm Group 13 All Area User Code The default installer user 50 PIN 4346 is assigned Alarm Group 3 which controls only the areas contained in Area Group 1 Alarm Group 3 cannot be edited but Area Group 1 can have areas added to it Note If an installer needs to program a system with more than areas 1 to 16 then they should first modify Area Group 1 so that it contains all the required areas Default installer PIN Changing the default installer PIN The default panel programming includes PIN 4346 for user 50 The default PIN must be changed to keep unauthorised persons from modifying your programming or using the system without authorisation 26 Challenger10 Installation a
33. n process e Disarming the system below e Accessing the Challenger menu below e Clearing the memory on page 24 e Working with multi area systems on page 26 e Changing the default installer PIN on page 26 e Enabling communications on page 27 An LCD RAS configured as RAS 1 must be connected to LAN 1 Disarming the system A new or defaulted Challenger10 panel is armed and the RAS LED for area 1 illuminates Previous Challenger versions armed all areas The system must be completely disarmed before you can access the Install menu on a system keypad LCD RAS To disarm the system 1 The default message displays on the top line of the RAS This line may display There Are No Alarms In This Area the time and date or a custom message There Are No Alarms In This Area Code 2 Press 4346 the default Installer code press OFF 0 to select all areas and then press ENTER Tip When using the system keypad numbers are entered in sequence For example press 4346 means press the 4 button the 3 button the 4 button and then the 6 button Accessing the Challenger menu The Challenger menu system as displayed on an LCD RAS has a first level User menu and a second level Install menu the Install menu is option 19 of the User menu Access to the Install menu is typically limited to installers or administrators 20 Challenger10 Installation and Quick Programming Manual Thi
34. n zone input circuits at the end of the circuit If an alarm device is connected place the EOL resistors at the device s connections If a zone input is not used you don t need to connect an EOL resistor if you program the corresponding input number as type 10 spare Tip Use sleeves on the resistor leads to prevent accidental shorting Figure 7 Four state monitored zone input circuits 1c c2c3 C 4c5C6C 7C8C9C 10C011C12C 13C14C15C 16C COOCOO BHOHOHOO BHHHHH HHHHGH O BHHOHOOHOHSOSO Normally open 10K Normally closed tamper contact tamper contact 10K 10K 10K e e Normally closed Normally open alarm contact alarm contact Challenger10 Installation and Quick Programming Manual 15 When four state monitoring is used the panel uses the circuit s resistance to determine the state of the zone input e 10 KQ indicates sealed e 5 kQO or 20 kQ indicates unsealed e Open circuit indicates input tamper e Short circuit indicates input tamper Alternatively the Challenger system can be configured to monitor zone inputs for two states sealed and unsealed This is accomplished by using one 10 kQ resistor in each circuit as shown in Figure 8 below Figure 8 Two state monitored zone input circuits 1c c2cC3C 4c5C6C 7C8C9C 10C11C12C 13C14C15C 16C SSSSSS HHHHH SHHSHEHH HHHHH SHSHSHHH SOO
35. nd Quick Programming Manual Restoring the default installer PIN If the installer PIN for user 50 has been changed and lost you may need to reset the PIN to default 4346 This is easily accomplished via management software However if necessary it can be done from the Challenger panel PCB Note This also defaults area group 1 back to areas 1 to 16 only and defaults RAS 1 on LAN 1 To restore the default installer PIN 1 Access the Challenger panel PCB 2 Fit test link 1 Figure 5 on page 11 item 22 momentarily and then remove the link Enabling communications Although basic programming and administration of the Challenger system can be done via a LCD RAS on the RS 485 LAN most systems use management software such as Titan Security Commander or Forcefield after installation The Challenger panel may communicate with a management software computer by an alternative path to provide backup reporting of alarms This section describes the RAS programming required to prepare for communications between the Challenger panel and a Titan management software computer Refer to the documentation provided with the management software for additional details if required Notes for New Zealand application e Refer to Regulatory requirements for New Zealand on page iii e If reporting via the Challenger panel s onboard modem the Communications option New Zealand Dialling must be enabled Challenger10 programming Cha
36. ogram the system s timers if the default values are not suitable The default values for timers are e Each user category time is set to 0 minutes e Access test time is set to 15 minutes e Secure test time is set to 15 minutes e Warning time is set to 5 minutes e Delay holdup time is set to 60 seconds e Suspicion time is set to 15 seconds e Service time is set to 30 minutes e Local alarm reminder time is set to 0 minutes e Individual testmode time is set to 5 minutes e Door unlock time is set to 5 seconds e Tester event flag time is set to 15 seconds e Siren time is set to 8 minutes e Mains fail time is set to 0 minutes e Card to code time is set to 8 seconds Challenger10 Installation and Quick Programming Manual Install menu option Description 7 System Options 8 Auto Reset 9 Communications 10 Text Words 11 Version 12 Lamp Test 13 Time Zones 14 Defaults 15 User Category 16 Map Relays 17 Arm Disarm via Tz 18 Vaults 19 Area Linking 21 Input Shunts 22 TZ to Follow Relays 23 Poll Errors 24 Download 25 Display Last Card Program the system options if the default values are not suitable The default values for system options are e Film Low is set to 800 e Film Out is set to 1100 Input tamper monitoring is selected Display one input at a time is selected e User name file is selected e EOL resistor is 10K Program the Challenger to automa
37. onnect the data cable shield to the LAN earth connection Figure 5 on page 11 item 1 The RS 485 LAN may be used to power devices up to 100 m cabling distance from the Challenger panel See Power supply to RS 485 LAN devices on page 4 for details One set of terminals is provided for each LAN if you need more than one connection you can use a TS0844 board to increase the number of terminals see TS0844 Power Distribution Board on page 8 Terminating the RS 485 LANs All Challenger LAN devices including the panel use a 470 Q LAN termination resistor where required LAN termination resistors are used to set the impedance of the LAN to around 220 Q in order to minimise noise The termination resistor may be external or onboard devices with an onboard resistor use a link or a DIP switch to set the LAN termination to ON A Challenger LAN should have only two devices with the LAN termination set to ON or the LAN termination resistor fitted e Ina straight LAN configuration Figure 1 on page 5 the TERM links are ON at the Challenger panel and the most distant device e Ina star LAN configuration Figure 2 on page 7 the TERM links are ON at the two devices that are the furthest apart and OFF at the Challenger panel if it s not at the end of one of the longest cable runs See also Star LAN on page 6 In a completely connected but powered down system you can check for correct LAN termination by measuring the re
38. ring panels DGP These devices extend the system s intrusion detection and access control functions Refer to the Challenger10 Programming Manual for details Product contents Table 1 below lists the items that are shipped with TS1016 Challenger10 Table 1 Challenger panel shipping list Quantity Item Metal enclosure with four spring standoffs fitted Challenger panel board 604 to RJ12 lead line 1 5 m Challenger10 Administrators Manual Challenger10 User Manual Challenger10 Installation and Quick Programming Manual 16 Volt AC plug pack Q A ee ee ee ee MA Tamper switch Tamper switch metal bracket Ring terminal M3 x 14 pan head screws 3 way plug on screw terminal connectors 2 way plug on screw terminal connectors Red battery lead with QC terminal Black battery lead with QC terminal ey fee fi ek ke eee eae Pe J ew oO uo 1K 1 4 watt resistor A 10K 1 4 watt resistors Inspect the package and contents for visible damage If any components are damaged or missing do not use the unit contact the supplier immediately If you need to return the unit you must ship it in the original box Challenger10 Installation and Quick Programming Manual 1 Before you begin This section contains items that govern the installation of many different Challenger system devices including but not limited to the Challenger panel When installing a Challenger panel or any other parts of the system you need
39. s manual describes the Challenger programming that you may need for basic system setup Refer also to Challenger10 Programming Manual for details of Challenger system programming via the Install menu Challenger10 Administrators Manual for details of Challenger programming and operation via the User menu User menu options As part of the basic system setup you may need to use the following User menu options Option 12 Test Input Option 14 Program Users Option 15 Program Time amp Date Option 20 Door amp Floor Groups Option 21 Holidays To access the User menu Use the following steps to access the Challenger User menu when the Code prompt is displayed on the bottom line of the RAS 1 Press MENU To Access Menu Enter Code Code Enter 4346 default Installer code and then press ENTER 0 Exit ENTER Down Up 0 Exit Menu You can now select the programming option you need from the User menu To access the Install menu enter 19 Install menu option number and then press ENTER Install Menu 0 Exit Menu You can now select the programming option you need from the Install menu see Table 2 on page 22 Install menu options The Install menu options and the default settings of particular importance to installers are listed in Table 2 on page 22 Challenger10 Installation and Quick Programming Manual 21 Table 2 Install menu options and selected default values
40. sistance across the Challenger panel s D and D terminals e 0 indicates a short circuit in the cabling 14 Challenger10 Installation and Quick Programming Manual e 160 Q or less indicates that three or more devices are terminated e 220 Q is good two devices are terminated e 470 Q or more indicates that less than two devices are terminated Checking LAN performance Use Install menu option 23 Poll Errors to check for poll errors on the LANs If the rate of poll errors seems excessive check the LAN cabling and termination Zone inputs Zone inputs are also known as alarm inputs A Challenger10 system can receive alarm signals from e The Challenger panel s onboard inputs numbered 1 to 16 e Inputs numbered 17 to 496 via Data Gathering Panels DGPs on LAN 1 e Inputs numbered 497 to 1008 via DGPs on LAN 2 Note Input numbers in the range 1000 to 1008 will not report CID alarms Each pair of zone input terminals may be connected to an alarm system device such as a detector or reed switch By default the Challenger system can monitor zone inputs for four states sealed unsealed open circuit and short circuit This is accomplished by using two end of line EOL resistors in each zone input circuit as shown in Figure 7 below Note The Challenger system s EOL resistor value is configurable in system options The default value is 10K and all examples in this manual are based on the default value Install EOL resistors i
41. tents Interlogix assumes no responsibility for errors or omissions ii Challenger10 Installation and Quick Programming Manual Regulatory requirements for New Zealand Some parameters required for compliance with Telecom s Telepermit requirements are dependent on the equipment PC associated with this device In order to operate within the limits for compliance with Telecom s Specifications the associated equipment shall be set to ensure that There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation The equipment shall go on hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt Automatic calls to different numbers are spaced such that there is no less than 5 seconds between the end of one call attempt and the beginning of another This equipment shall not be set up to make automatic calls to the Telecom 111 Emergency Service The associated equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing Refer to the Challenger10 Programming Manual for details about programming these parameters Challenger10 Installation and Quick Programming Manual Preface This is the Challenger10 Installation and Quick Programming Manual It is part of the following suite of manuals for the Challenger10 intrusion detection and access control panel e The C
42. tically reset alarms Program the communications devices and paths for reporting to a remote monitoring company connecting to management software computers and so on If your system requires text words not found in the standard text word library you can program up to 400 custom site specific text words Display the system s device types and firmware version numbers Toggle the on off state of all RAS LEDs in the system so that they may be checked Define time slots hard time zones in which certain events can take place Reset the panel to default settings User categories provide timing for areas that are configured for timed disarming or for delayed arming via vault programming Link relays outputs to event flags and or time zones The default values for relay mapping are e Relay 2 panel strobe output is mapped to event flag 2 e Relays 16 32 48 64 and so on panel siren driver are mapped to event flag 1 The sixteenth relay assigned to each DGP DGP siren drivers is mapped to event flag 1 Define arm disarm timer programs Areas being armed or disarmed automatically by time zone do not require any user action Define areas that when armed will automatically arm other areas after a specified time Define a common area that is armed only when the last shared area is armed Define shunt timers to inhibit inputs from generating alarms during a specified interval Define soft time zones Time zones
43. trobe i J 8e amp le o lejos LAN 2 optional Q 1 RS 485 data cable lo no ee 16 VAC plug pack Notes e Use the 16 VAC plug pack supplied with the Challenger panel e When installing plug packs do not power the unit until you have terminated all necessary wires and checked that you do not have a short circuit Fused plug packs cannot be replaced under warranty as the fuse operation can only be caused by a direct short circuit Challenger10 Installation and Quick Programming Manual 13 Auxiliary power terminals Connect the and auxiliary power output terminals to devices that require 12 VDC power such as detectors Four sets of auxiliary power output terminals are provided if you need more than four connections you can use a TS0844 board to increase the number of terminals see TS0844 Power Distribution Board on page 8 RS 485 LANs Use 2 pair twisted shielded data cable such as Belden 8723 to connect the Challenger panel to system devices such as RASs and DGPs e Connect the terminal to the red wire The terminal provides 12 V to LAN devices such as RASs within 100 m cabling distance e Connect the terminal to the black wire The terminal provides ve DC to LAN devices such as RASs and common 0 V for the RS 485 LAN e Connect the D terminal to the white wire The D terminal is data positive e Connect the D terminal to the green wire The D terminal is data negative e C
44. tware connection via User menu 7 Service Each of the 10 communications paths can be edited The default paths are provided as a shortcut to setting up the panel Each communications path must be assigned a format Table 3 below lists the relationship between formats and hardware Table 3 Communications formats by device type Formats Devices Dialler STU RS 232 IP USB CID Modem Yes No No No Computer Polled Yes Yes Yes Yes Computer Event No No Yes No SecureSteam IP Receiver No No Yes No Securitel STU No Yes No No Printer No Yes No No After you select a format many of the subsequent options are pre programmed with values appropriate to that format Note If you need to change the format of a path that has been previously programmed or one of the default paths first set the format to O None to clear the previous format s programming Refer to Figure 5 on page 11 for the locations of the panel s onboard ports The following default values are typically sufficient to establish communications with the management software computer e Security password 0000000000 e Security attempts 255 28 Challenger10 Installation and Quick Programming Manual Note It is advisable to change the settings for the password and security attempts once the management software is communicating with the Challenger panel Example 1 Programming a polled USB connection to a Titan computer You may use a USB cable Type A Male to
45. tween buildings to protect the system against differences in earth potential Figure 3 below shows the use of two TS0893 modules to extend the RS 485 LAN across two electrical installations Each TS0893 module has a pair of termination links used to terminate if applicable the LAN segment on each side of the module s isolation barrier Figure 3 RS 485 LAN cabling between two buildings Building A Building B Challenger ox Panel 4 AS T On TS0893 T O0n termination link fitted T Off termination link not fitted Challenger10 Installation and Quick Programming Manual 7 Figure 3 legend Item Description 1 LAN segment 1 extends from the Challenger panel to one side of the TS0893 LAN Isolation Interface Termination is ON at the panel and the panel s side of the TS0893 Maximum cabling distance for segment 1 is 1500 metres LAN segment 2 extends from the TS0893 in building A to the TS0893 in building B Termination is ON at both TS0893 modules Maximum cabling distance for segment 2 is 1500 metres Earth point on Challenger panel connected to building earth via plug pack earth wire green Earth point on remote device connected to building earth via plug pack earth wire green or earth wire from local power supply Plastic body LAN device Join data cable shields where cable extends past a device that doesn t have a LAN earth connection Using LAN devices to facilitate cabling Various LAN d
46. uired in particular change Enabled to Yes You might also need to change the account code and the computer password default is 0000000000 8 When returned to the Path menu select option 6 Path IP Address 9 Press ENTER to step through the options and program the following settings in particular program the Titan computer s IP address Use the default values if applicable for the Send and Listen IP Port numbers default is 3001 and UDP IP 10 Press 0 ENTER as needed to exit from the Communications menu 11 In Titan select Ports from the Admin menu 12 In the port record select UDP IP enter a port number description Challenger panel s IP address and IP Port number for example 3001 Save the record 13 Connect the Challenger panel s Ethernet port at J19 Figure 5 on page 11 item 16 to the LAN or directly to the Titan computer via a Cat 5 cable 14 Select Challenger from the Admin menu 15 In the Challenger record ensure the Challenger No and Security Password are the same as programmed via RAS type the port number in the Port field and select UDP IP as the communications mode Save the record 16 Select Open System from the File menu select Active System and then save the record The connection indicator at the bottom of the Titan window displays green to indicate a successful connection 30 Challenger10 Installation and Quick Programming Manual Programming users Unless you will be program
47. where cable extends past a device that doesn t have a LAN earth connection e The length of the LAN cable run should not exceed 1 5 km unless LAN isolation devices are used to extend the distance Challenger10 Installation and Quick Programming Manual 3 Power supply to RS 485 LAN devices Devices on the LANs may be supplied from the panel s or DGP s and LAN power terminals Use an external 12 V power supply such as TS0073 2 A Power Supply when e the device is more than 100 m data cable length from the panel e electrical isolation is required e more power is needed than can be provided by the LANs When powering a LAN device from an external 12 V power supply e Connect the external power supply s terminal to the device s terminal Do not connect the power supply to the LAN e Connect the external power supply s terminal to the device terminal e Connect the LAN cable black wire to the device terminal 4 Challenger10 Installation and Quick Programming Manual Figure 1 RS 485 LAN 1 or LAN 2 and earth system block diagram 3 O LAN Earth Challenger panel first device on LAN O Power Earth 6 TERM link on F F RAS without earth terminal
48. y class HB or better e Install equipment in a clean environment and where environmental conditions are within the range specified in the product data sheet Installation procedures A Challenger panel may need to be fitted with various add on modules and interfaces See each product s installation instructions for details Note Expander modules must not be fitted to a powered Challenger panel Remove power before plugging an expander module onto the Challenger PCB To mount the Challenger enclosure 1 Fix the enclosure to the wall via the enclosure s four mounting holes Figure 4 on page 9 item 1 Make sure the enclosure is level and the tamper switch item 3 location isn t sitting over a line of mortar if you re installing the enclosure on a brick wall To mount the tamper switch The two way tamper switch detects removal of the cover from the enclosure and removal of the enclosure from the wall 1 Insert the tamper switch into its metal bracket 10 Challenger10 Installation and Quick Programming Manual 2 Insert the bracket with tamper switch into the 1 cm slot on top left hand side of the enclosure Figure 4 on page 9 item 3 To mount the Challenger board to the enclosure 1 Remove the Challenger board from its antistatic bag 2 Use four M3 x 14 pan head screws to fix the Challenger board to the enclosure s standoffs Figure 4 on page 9 item 2 3 Slide the board s terminal connectors together and
Download Pdf Manuals
Related Search