PA168V SIP FXS Gateway User Manual
Contents
1. e rtp port RTP port is the port transferring and receiving voice packets using UDP protocol This is an even number between 1024 and 65535 e rtp tos Set the TOS field of the IP header of the RTP packets The bigger this value is 0 the higher priority the packet is 224 e call type Set call type by selecting the items in drop down list normal When SIP system not support outbound proxy selecting this item a advanced When SIP system support outbound proxy selecting this item Default setting is this item e dtmf Set DTMF signal sending way by selecting inband audio rfc 2833 and sip info from list box Beijing Centrality Communication Inc 21 PA168V SIP FXS Gateway User Manual V1 42 e dtmf payload When DTMF select rfc 2833 This parameter can be used indicating type of RTP payload type The value can be use integer 96 101 e super password Set the super password of PA168V gateway Default super password is 12345678 e debug Set the debug level of PA168V gateway a disable Disable output the debug message by selecting this item output Output the operation information to the window such as register input by selecting this item output all Output all debug information and data in test window by selecting this item remote debug Save the debug information in SDRAM of PA168V by selecting this item a no check Disable checking firmware tags when upgrading This is not sugges2. set nataddr XXXXX When nattraversal is set to 1 set IP address of NAT device wan port or URI of free assistant service Such as www showmyip com etc in Internet When nattraversal is set to 2 set IP address or URI of the stun server in the format as domain name IP address service port The default service port for stun is 3478 NOTE The free service list of Internet www ip calculator com www ipchicken com www ipchicken com www showmyip com www whatismyip com www myipaddress com www whatismyipaddress com ip sbbs net www whatismyipaddress net checkip dyndns org set natttl XX Beijing Centrality Communication Inc 38 PA168V SIP FXS Gateway User Manual V1 42 Set NAT TTL XX is an integer between 10 and 65535 sec default value is 20 sec set phonenumber XXXXXXXX Set a local ID of PA168V gateway Value xxxxx must be an Arabic numeral and no longer than 16 characters set account XXXXXX Set the account Value xxxxxx must be an Arabic numeral and no longer than 32 characters set pin XXXXXXXXXX Set the account Value xxxxxx must be an Arabic numeral and no longer than 32 characters set registerport XXXX Set register port Value XXXX default is 5060 set rtpport XXXX RTP port is the port transferring and receiving voice flow using UDP protocol XXXX is an even number between 1024 and 65535 set rtptos X Set TOS segment of IP head package in RTP digital follow X is range from 0 thro
3. PA168V SIP FXS Gateway User Manual V1 42 example the area code of Beijing is 10 the area code of Shanghai is 21 and the area code of Chengdu is 28 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set iddcode XXX Set the country code when set dialplan value set as 1 or 2 For example the country code of China is 86 the country code of USA is 1 etc Parameter xxxx must be an Arabic numeral and no longer than 4 characters set iddprefix XX Set IDD service prefix number when set dialplan value set as 1 or 2 For example IDD service prefix number of china is 00 IDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set dddprefix XX Set DDD service prefix number when set dialplan value set as 1 or 2 For example DDD service prefix number of china is 0 DDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set innerline X Set use innerline call or not X ranged from 0 through 1 0 disable 1 enable innerline call Beijing Centrality Communication Inc 34 PA168V SIP FXS Gateway User Manual V1 42 set innerlinepreifx X With innerline set as 1 enable please set the prefix to pick up inner line such as 0 set callwait X Set whether to use call wait X ranged from 0 to 1 0 do not use call wait 1 use call wait set fwdnumber XXXXXXX Set receiving forwarded calls phone
4. Set buffer size of RTP package The value range is 0 32 Beijing Centrality Communication Inc 13 PA168V SIP FXS Gateway User Manual V1 42 e g 723 1 high rate enable disable g 723 1 high rate G 723 1 high rate is 6 3kbps low rate is 5 3kbps Gateway Setting Phone Settings use dialplan disable gt dial number jeo ts ddd code fio idd code je idd prefix po ddd prefix poo inner line disable v inner line prefix call waiting 7 forward number 82378801 fwd poweroff O fwd noanswer T fwd always O fwd busy O answer fo use digitmap handset in 0 15 po handset out 0 31 p2 p dual mode pstn first dual mode prefix Fig 3 4 Gateway Setting e use dialplan Set whether use dial plan or use dial number by selecting the corresponding item in drop down list m disable Do not use dial plan or dial number by selecting this item enable Use dial plan by selecting this item dialnum Use dial number by selecting this item With this item selected please enter the dial prefix into dial number field m prefix Use 179XX service by selecting this item Hotline Use Hotline function by selecting this item With this item selected please enter the hotline number into dial number field e dial number With dialnum selected in use dialplan drop down list please enter the dial prefix into this field according to requirement of log in server For example with eTalk card used enter 00 here e ddd code With enable o
5. IP address of time server set daylight X Set use daylight or not X ranged from 0 through 1 0 do not use daylight 1 use daylight set timezone XX Set time zone Command store Syntax description no keyword Parameter ranged from 0 through 4 Usage Save the current settings to the designated position Relevant Usage store 1 Command load Syntax description no keyword Parameter ranged from 0 through 4 Beijing Centrality Communication Inc 41 PA168V SIP FXS Gateway User Manual V1 42 Usage Load the designated settings to the current position Relevant Usage load 1 Command exit Syntax description no keyword and parameter Usage Exit from Telnet command window without saving the configuration Relevant usage None Command write Syntax description No keyword and parameter Usage Save the configuration and restart the PA168V FXS gateway Command ping Syntax description ping IP address Usage ping IP address of other NAT device Relevant usage In telnet window input ping xx xxx xx xx an IP address and return then the result will be displayed If the address is effective ping OK will be seen If the address is ineffective nothing will be seen Fox example P gt ping 203 93 9 57 P gt ping OK P gt ping 27 56 120 56 Beijing Centrality Communication Inc 42 PA168V SIP FXS Gateway User Manual V1 42 P gt Note Usually the echo time of ping command is no m
6. address of PA168V complies with the requirements of t the firmware configuration and dial rules files it will be upgraded or configured automatically When the upgrading is done MAC address of PA168V will keep unchanged while other parameters will be upgraded as in the new configuration files Upgrade the matching PPP ID Use this way to match PPPID When PPPID of PA168V complies with the requirements of t the firmware configuration and dial rules files it will be upgraded or configured automatically Beijing Centrality Communication Inc 48 PA168V SIP FXS Gateway User Manual V1 42 When the upgrading is done PPPID of PA168V will keep unchanged while other parameters will be upgraded as in the new configuration files Upgrade the matching Account Use this way to match the account When the account of PA168V complies with the requirements of t the firmware configuration and dial rules files it will be upgraded or configured automatically When the upgrading is done the account of PA168V will keep unchanged while other parameters will be upgraded as in the new configuration files Upgrade the matching phone number Use this way to match the phone number When the phone number of PA168V complies with the requirements of t the firmware configuration and dial rules files it will be upgraded or configured automatically When the upgrading is done the phone number will keep unchanged while other parameters will be
7. of PA168V FXS gateway will ring to remind you You can receive the call by picking up the phone or using the hand free set gt When the dual mode of the PA168V is disable Make a call e Make a call using phone number 1 Use the handset to make the call Picking up the handset of the ordinary phone and after hearing the dial tone dial your number to make a call 2 Use the handfree to make the call Press the handfree of the ordinary phone and after hearing the dial tone dial your number to make a call 3 Redial When you want to redial Pick up the handset or press the handfree then after hearing the dial tone Press the Redial key e Make a call using IP address If PA168V FXS gateway does not register to the SIP Proxy you can make a Call directly through dialing the IP address of other party 1 Picking up the handset of the ordinary phone and after hearing the dial tone input the IP address then press key to make a call 2 Press the handfree of the ordinary phone and after hearing the dial tone input the IP address then press key to make a call Beijing Centrality Communication Inc 44 PA168V SIP FXS Gateway User Manual V1 42 Note When input the IP address by keypad of ordinary phone use to replace gt When the dual mode of the PA168V is set as PSTN first Make a call with PSTN line When PA168V is set as PSTN first and when you pick up the handset the pone will be linked with the public
8. range from O through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec6 X Set the priority 6 of the audio compression algorithm X is range from O through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set vad X Enable disable VAD X is ranged from 0 through 1 0 disable VAD 1 enable VAD set agc X Enable disable AGC X is ranged from 0 through 1 0 disable AGC 1 enable AGC set aec X Enable disable AEC X is ranged from 0 through 1 0 disable AEC Beijing Centrality Communication Inc 32 PA168V SIP FXS Gateway User Manual V1 42 1 disable AEC set audioframes X Set audio frames in RTP package X is Arabic numerals between 0 and 7 set jittersize X Set buffer size of RTP package X is range from 0 32 set 6 3k X With G 7231 codec selected set PA168V FXS gateway to use 6 3K rate or not X is ranged from 0 through 1 0 use 6 3K rate 1 use 5 3K rate set dialplan X Enable disable dial plan and dial number Parameter X ranged from O through 4 0 disable dial plan 1 enable dial plan 2 use dial number 3 use 179XX service 4 use hotline function set dialnumber XX When set dialplan value set as 2 please use this command to set dial number For example with eTalk card used please set it as 00 When set dialplan value set as 4 please use this command to set hotline number set dddcode XX Set the area code when set dialplan value set as 1 or 2 For Beijing Centrality Communication Inc 33
9. select this item for it is a protocol especially designed for them modem Users of PA168V FXS gateway attached with modem please select this item Then please fill user name and password of dial up network into ppp id and ppp pin fields e ppp id With pppoe selected in iptype drop down list please enter the ADSL user name here with modem selected in iptype drop down list please enter the modem dial up user name here The length of the user name is limited within 40 bytes e ppp pin With pppoe selected in iptype drop down list please enter the ADSL password here with modem selected in iptype drop down list please enter the modem dial up password here The length of the password is limited within 24 bytes Beijing Centrality Communication Inc 11 PA168V SIP FXS Gateway User Manual V1 42 e local ip With static ip selected in iptype drop down list please enter IP address acquired from the administrator or ISP e subnet mask With static ip selected in iptype drop down list please enter subnet mask acquired from the administrator or ISP e router ip With static ip selected in iptype drop down list please enter the default Gateway IP address on which the PA168V locates in the network e dns With static ip selected in iptype drop down list please enter the IP address of the main DNS server e dns spare With static ip selected in iptype drop down list please enter IP address of backup DNS serve
10. standard WEB browser Double click lj icon to open the IE Input the IP address of the PA168V into address bar e g 192 168 1 100 Address http 192 168 1 100 and then input password of the PA168V into the following page Default ordinary password is 1234 and super password is 12345678 If the default password is invalid please consult the supplier With Debug set O disable please input super password while Debug Beijing Centrality Communication Inc 9 PA168V SIP FXS Gateway User Manual V1 42 is not set as O disable please input ordinary password Then clickL__222in___Jbutton The following configured page wills popup Refer to Fig 3 1 please Network Settings iptype static ppp id oe Ppp pin a local ip fi92 168 1 100 subnet mask 255 255 255 0 router ip 192 168 1 254 dns 202 106 46 151 dns2 202 96 128 68 mac 00 0d ea 00 00 03 Audio Settings codeci e729 codec2 fe7231 gt codec3 gTlluy codec4 etia gt codec5 fesn gt codec6 u z vad r age D aec IV audio frames ie jitter size 0 zg 723 1 high rate Phone Settings use dialplan disable dial nunber feso ddd code idd code jpe idd prefix ddd prefix inner line disable x inner line prefix forward mmber 82378801 fwd poweroff fwd always L fwd busy call waiting fwd noanswer answer TTi use digitmap r handset in 0 15 handset out 0 31 dual mode pstn first gt dual mode prefix SIP Protocol Settings use service V
11. then upgrade x 2 Link to the FTP Server to get the dialplan rules file and then upgrade m Use HTTP Use Web brownser to visit PA168V FXS gateway Please use super password to log in Click ___Uperade Firmware there will pop up a corresponding page As to the details please refer to the part of Upgrading Program Update Digitmap in the chapter of Configured with the standard web browser gt Automatic upgrading The auto upgrading is used only with the FTP server It is mostly used by the service provider or manufactory When the auto upgrading is done and PA168V FXS power on the PA168V Beijing Centrality Communication Inc 47 PA168V SIP FXS Gateway User Manual V1 42 will to link with the FTP server automatically to get the firmware configuration and dial rules files According different purposes the following different matching ways together with different the firmware configuration and dial rules files can be adopted to configure and updateing Upgrade the matching type of hardware Use this way to match the type of hardware When the type of the hardware complies with the requirements of t the firmware configuration and dial rules files it will be upgraded or configured automatically When the upgrading is done the type of hardware will keep unchanged while other parameters will be upgraded as in the new configuration files Upgrade the matching MAC address Use this way to match MAC address When MAC
12. PA168V SIP FXS Gateway User Manual V1 42 PA168V SIP FXS Gateway User Manual gt PA168V SIP FXS Gateway ADPCAlAriCe cccccccccccceccesecseeecseeseeseesecsseeecasenseeseesenaeeseneeaseaes 3 gt Indicators and the setting key functions 4 gt PA168V SIP FXS Gateway fEAtUIeS ececcecesceccsseseesenseseesenseseeseaseseeseaseaeesenseaeeseneeaeeneneeaes 4 gt Slandard ANA POCOCOL ceccenaeanea a AA A 6 gt Operating requirements oo ececccecccsceescnesecesesseeseesenecaessecasesesasessesaecsessecseesecasenaeeaeesesaeeseeneesaeaes 6 gt Electric requiremMentS sseseseseseesesesseserrereseesssesesreresesssseseseerrsesesesesrenesssreseseerenesesseseseere 7 Be ALLE EEE E INE OEE A E ET EA EE AE E 7 Pr MTSTAN AU ONT E ss a RE T A E ua cats A E E shah E E canes 7 CONNIE AAEN AA NAAR 8 gt Configuration with the standard WEB brOWSeT eeeeeeeeeeeeeeesesresrrrsrresesrses 9 BP Fel COMMG UAL ON en esx cuca sates E E E ee eg ca a aed EEE Lege dada ca sates ew Rada E EES 25 gt PA168V Telnet Commands Explanation ccccccccccccceccccssesecssseesesssseeseescseeseessseeseeseseeseesesenaes 26 gt PA168V TELNET COMMANDS scssssesecesssssssesesesesesesceeeeeecececeesenenenensneesecececeseseasaeaseseceeeeeeeeees 26 gt Operation of PA168V FXS GAlOway ccccecceccseseeserseseescsseseesceeseescaeeaeeecaeeaeeeeaeeaeeeeaeeaeerenees 44 gt Receiving a eal aaa a EEn Hed E A RE needa R daa Aire nla 44 gt When the dual mode of the PA168
13. V is disable 44 gt When the dual mode of the PA168V is setas PSTN AiSt ssscccccccccsetetsneecsnetsnesetsnees 45 gt When the dual mode of the PA168V is set as IP St 45 Beijing Centrality Communication Inc PA168V SIP FXS Gateway User Manual V1 42 gt Emergency CA eee eccccccesecessecesessvseseesesesensssesesecsesenssseseseceesenssaesesecseaeneeaeseseceeaeeeeaeeeseaeaeeeeaeees 45 gt Centralize Upgrade and configuration of PA168V FXS gateway 46 gt Prepare firmware and configuration file 46 gt Manual upgrading and configuration seeeeeeeeeeeseeeessesrrerrresesesesesrsesrsses 46 gt Automate upg ad eienares 47 gt Recover the factory Settin9 eeseseseserersrrrsrrrrrrrsrrrerrrsrirrrrrrsrrrnrs 49 Beijing Centrality Communication Inc 2 PA168V SIP FXS Gateway User Manual V1 42 gt PA168V SIP FXS Gateway Appearance e Front view Refer to Fig1 1 POWER REG STATS USE CONNECT Fig 1 1 PA168V SIP FXS Gateway Front View e Back view Refer to Fig1 2 PSTN FXS PC NETWORK SET POWER Fig 1 2 PA168V SIP FXS Gateway Back Front View Beijing Centrality Communication Inc PA168V SIP FXS Gateway User Manual V1 42 gt Indicators and the setting key functions Indicators Functions Indicators Functions Light s on when power on Lights off when registered flashing Power Reg Stats when register failed Light s on when picking up off Light s flashing when call is connect
14. am into this field e nts ip Fill IP address of time server here When network without Internet Beijing Centrality Communication Inc 23 PA168V SIP FXS Gateway User Manual V1 42 Fill special address IP 255 255 255 255 here e use daylight Enable disable daylight e timezone Select correct time zone in list box When debug set as O disable if input ordinary password default one is 1234 then following page will pop up after clicking Cei And only those parameters can be modified Network Settings iptype dhcp ppp id e PPP pin eT local ip fi92 168 1 221 subnet mask 255 255 255 0 router ip fi92 168 1 254 dns f202 106 46 151 dns2 f202 96 128 68 mac 00 09 45 63 66 af Audio Settings codecl e729 gt codec2 27231 gt codec3 feTllu z codec4 eTila z codec5 esn gt codec8 null vad E age B aec Vv audio frames e jitter size 0 zg 723 1 high rate Vv Phone Settings use dialplan disable gt dial number keno tits ddd code fic idd code fe idd prefix foo ddd prefix p inner line disable x inner line prefix o call waiting Ll forward number 82378801 fwd poweroff L fwd noanswer E fwd always D fwd busy O answer p use digitmap T handset in 0 15 Pp handset out 0 31 22 dual mode pstn first gt dual mode prefix ps Other Settings password 1234 upgrade type disable x upgrade addr sntp ip o 0 0 0 use daylight Vv timezone GMT 08 00 Pacific Time U S amp Canada Y Save Settings Ad
15. dr field will be activated Besides port mapping port forwarding needs to be properly set up on NAT device stun Select this item with Stun server used according to requirement of system With this item selected nat addr field is activated e nat addr When nat traversal is set to enable please put the domain name of the servers These web server helps to find out the public IP of the NAT device into nat addr such as www whatismyip com When nat traversal is set to stun please put the URI of the stun server into nat addr in the format as domain name IP address service port The default service port for stun is 3478 e nat ttl When PA168V gateway sit behind a NAT device it will send packets to server every nat ttl seconds to keep the port mapping on the NAT device alive nat ttl is an integer between 10 and 65535 default value is 20 e phone number The local phone number or username of PA168V Beijing Centrality Communication Inc 20 PA168V SIP FXS Gateway User Manual V1 42 gateway usually is allocated by system e account With SIP system which requires authentication please put the username account into this field e pin With SIP system which requires authentication please put the password into this field e register port The local UDP port registered with server to accept incoming handshaking messages The default port number is 5060
16. dress Book Upgrade Firmware Fig 3 7 Setting Page using ordinary password with Debug set as 0 disable e Update Click this button to save the configuration and PA168V will reboot Once PA168V reboots successfully the new configuration is effective Note After entering set page if Update button is not clicked within 10 minutes then Beijing Centrality Communication Inc 24 PA168V SIP FXS Gateway User Manual V1 42 when you click it again the index page asking for pin will pop up again Then please input the password again to enter the set page and then click Update button to confirm the modification Phone Book Click this button to open the speed dial settings page Please refer to Fig 3 7 In this page you can set and save the speed dial number by typing the name into the Name field and then entering the corresponding number following the name For example input Jack in Name field following 001 and then input 5989426454 into Phone number field Then Jack s number 5989426454 is saved in phone book Then please click Save Back button In normal state you can use speed dial to call numbers saved in phone book Phone Book Ho Hame Phone Number No Name Phone Number 001 Tack 5989426454 002 Allen 192 168 1 56 omaa i Ee ke keel ef jyt yoy yyy l a o lll O O y O un O O poopy yl Fig 3 8 Phone Book Illustration Upgrade Program Click this button to update the program of the PA168V Update Di
17. ed USE Connect when hung up off when call is disconnected Button Functions 1 With handset hung press this key to indicate local IP address with voice prompt Please refer to the details in the Use ordinary telephone keyboard pre setting chapter 2 Set the connect network type please refer to the details in the Use ordinary SET telephone keyboard pre setting chapter 3 When IP type using the static IP use the required static IP address 4 To set PA168V in setup mode please refer to the Use ordinary telephone keyboard pre setting chapter gt PA168V SIP FXS Gateway features gt Hardware e Main chip PA1688LQ 50MHz e Data Memory 2MB SDRAM e Program Memory 2 MB Flash memory Beijing Centrality Communication Inc 4 PA168V SIP FXS Gateway User Manual V1 42 e FXS Jack 1 XRJ 11 e POTS Jack 1XRJ11 PSTN telephone line jack e Ethernet Jack 2X10 100M auto negotiate interface e AC DC adapter Input AC100 220V Output 9V DC 1A gt Software e DHCP support for automatic assigning IP addresses e PPPoE support for ADSL or Cable modem e Setup by HTTP web browser or Telnet e Upgraded and Configured by FTP and HT TP TFTP optional e Support major G 7XX GSM610 audio codec e VAD Voice active detect e CNG Comfort noise generation e Dynamic voice jitter buffer e G 167 165 compliant 16ms acoustics echo cancellation e Tone generation and Local DTMF re generation accordi
18. from 10 through 65535 Sec default value is 60 Sec set service type X Beijing Centrality Communication Inc 36 PA168V SIP FXS Gateway User Manual V1 42 Enable disable the repaid and service system choose the repaid server provider Parameter x ranged from 0 through 15 0 common disable repaid card or specially system 1 use huawei s system 2 use ZTE s system 3 use harbour s system 4 use utstarcom s system 5 use uptech system 6 use keimen s system 7 use meidaring s service 8 use italkBB service 9 use stanaphone service 10 use net2phone SIP service 11 use fwd freeworlddialup service 12 use inphonex system 13 use sipphone system 14 use ngtel system 15 use ayctel system set sipproxy XXXX Set IP address or domain name of SIP Proxy Server If the system has an Outbound Proxy set IP address or domain name of Outbound Proxy Beijing Centrality Communication Inc 37 PA168V SIP FXS Gateway User Manual V1 42 set domain realm XXXXX If the system has an Outbound Proxy Set the domain name of SIP proxy server such as Xxxx set nattraversal X X ranged from 0 through 2 0 do not use NAT traversal When the log in server and PA168V in the same LAN or the log in system supports PA168V working behind the LAN 1 Use NAT traversal When the login system does not support PA168V working behind the LAN With this item selected please make port mapping on NAT device 2 stun
19. gitmap Click this button to update the digitmap of the PA168V gt Telnet Configuration e On the PC choose Start gt Run and then type telnet 192 168 1 100 into Beijing Centrality Communication Inc 25 PA168V SIP FXS Gateway User Manual V1 42 Run field in popuping Run dialog Or input telnet 192 168 1 100 in the DOS window Then the following information will be display PA168X V1 42 settings Password Then please type password With debug is set as O disable if type ordinary password default one is 1234 after Retun you will see Password P gt If you type super password then you will see Password a kkkkkkkk P gt Above information indicates that PA168V FXS gateway is under setting mode and then you can set the PA168V FXS gateway by using the telnet commands gt PA168V Telnet Commands Explanation PA168V Telnet Commands Command Function Supply command name and parameters get Display basic parameters of the PA168V FXS gateway set Set parameters of the PA168V FXS gateway Beijing Centrality Communication Inc 26 PA168V SIP FXS Gateway User Manual V1 42 store Save current settings to designated position load Load designated settings to current position exit Exit from the setting mode without saving the configuration write Exit with saving all configurations and restart PA168V ping Ping other net parameter ftp The PA168V connects to FTP server and then get the files Detail de
20. ith modem with modem item selected in iptype list box and then fill ISP number into this field e fwd noanswer Forward calls without replying by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd always Forward all calls by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd busy Forward calls if busy by checking this box Please enter receiving forwarded calls phone number into fwd number field e answer Enter a number from O through 60 to set the entries of the seconds before the phone answer the call auto or forward the calls e Use digitmap Enable disable digit map by checking unchecking the box e handset in Set the volume of handset input e handset out Set the volume of handset output e Dual mode Set this item to enable or disable the PSTN line Disable This item selected Disable PSTN line a PSTN First This item selected PA168V FXS gateway will choose Beijing Centrality Communication Inc 16 PA168V SIP FXS Gateway User Manual V1 42 PSTN calling first a IP First This item selected PA168V FXS gateway will choose IP calling first e dual modes prefix When IP first is set in the dual modes setting setting switches to PSTN prefix such as 9 Protocol Setting SIP Protocol Settings use service Iv register ttl jo service type common 7 sip proxy fw sipphone con domain realm fw
21. ix 00 dddprefix 0 innerline 1 enable innerlineprefix 0 callwaiting 1 disable fwdnumber 82378009 fwdpoweroff 1 enable fwdalways 1 enable fwdbusy 1 enable fwdnoanswer 1 enable answer 30 digitmap 1 enable handsetin 5 handsetout 20 ringtype O dtmf speakerout 20 speakerin 1 KAE Protocol Settings service 1 enable registerttl 60 servicetype O common _ sipproxy www iax2 com domain realm www sipphone com Beijing Centrality Communication Inc 28 PA168V SIP FXS Gateway User Manual V1 42 nattraversal O disable nataddr empty natitl 0 phonenumber 8870054 account 8870054 registerport 5060 rtpport 1726 calltype 1 advanced dtmf O inband audio SRERAEEKEREESES OTH OF Settings 4 superpassword 12345678 debug 1 output password 1234 upgradetype O disable upgradeaddr empty sntpip 0 0 0 0 daylight O disable timezone 55 GMT 08 00 Beijing Hong Kong Urumaqi pin 418668077 rtptos 0 dtmfpayload 101 Input ordinary password with debug set as O disable following information will be seen PA168X V1 42 settings Password P gt get seeen Network Settings e ee iptype O static ip 192 168 1 100 subnetmask 255 255 255 0 dns 202 106 46 151 dns2 202 96 128 68 steer Adio Settings tt router 192 168 1 254 mac 00 0d ea 00 00 03 codec 0 g729 codec2 1 g7231 codec3 2 g711u codec4 3 g711a codecd 4 gsm codec6 6 null vad 1 enable agc O disable aec 1 enable audioframes 2 jittersize 0 6 3k 1 enable
22. ng with ITU T e E 164 dial plan and customized dial rules e 100 entries for speed dial e Voice prompt local IP address e Hotline e Support adjustable user password and super password Beijing Centrality Communication Inc PA168V SIP FXS Gateway User Manual V1 42 gt Standard and Protocol PA168V SIP FXS gateway supports following standard and protocol e IEEE 802 3 802 3 u 10 Base T 100Base TX e Major G 7XX GSM610 audio codec e SIP RFC 2543 RFC3261 e TCP IP Internet transfer and control protocol e RTP Real time Transport Protocol e RTCP Real time Control Protocol e VAD CNG save bandwidth e DHCP Dynamic Host Configuration Protocol e PPPoE PPP Protocol over Ethernet e DNS Domain Name Server e Telnet Internet s remote login protocol e FTP File Transfer protocol e TFTP File Transfer protocol optional e HTTP Hyper Text Transfer protocol gt Operating requirements e Operation temperature 0 to 50 C 32 to 122 F e Storage temperature 30 to 65 C 22 to 149 F e Humidity 10 to 90 no dew Beijing Centrality Communication Inc PA168V SIP FXS Gateway User Manual V1 42 gt Electric requirements e Voltage 9V DC e Power 9W max e Power adapter AC DC input 100 230V Output 9V 1A e Network interface 2X RJ 45 Ethernet Connectors e FXS jack 1XRJ 11 telephone jack e POTS jack 1XRJ 11 PSTN telephone line jack gt Size 153 x 124 x 27 mm L x W x H g
23. number XXXX must be an Arabic numeral and no longer than 16 characters set fwdalways X Enable disable forward all calls X is ranged from 0 through 1 0 do not forward all calls 1 forward all calls set fwdbusy X Enable disable forward calls if busy X is ranged from 0 through 1 0 do not forward calls if busy 1 forward call if busy set fwdnoanswer X Enable disable forward calls without replying X is ranged from 0 through 1 0 do not forward calls without replying 1 forward call without replying set answer X Set the ring seconds before the phone answers the call auto or forward the calls X is ranged from 0 through 60 Beijing Centrality Communication Inc 35 PA168V SIP FXS Gateway User Manual V1 42 set digitmap X Set whether to use digitmap X ranged from 0 to 1 0 do not use digitmap 1 use digitmap set handsetin X Set initial volume of handset X is ranged from 0 through 15 set handsetout X Set initial volume of handout X is ranged from 0 through 31 set dualmode X Set to enable or disable the PSTN line X is ranged from 0 through 2 0 do not use PSTN line 1 use PSTN line first 1 use IP side call first set dual modes prefix XX When IP first is set in the dual modes setting setting switches to PSTN prefix XX is ranged from 0 through 99 set service X Set register the SIP proxy server or not X ranged from 0 through 1 0 do not register 1 register set registerttl X Set register TTL X is range
24. ore than 1 second So if the result is not displayed in 5 seconds ping command is fail ftp command Syntax description ftp value Usage the system connects to the FTP server auto to get the corresponding file and deal with it Relevant usage ftp X X ranged from 0 through 2 X 0 Connect to FTP Server to get the file of updating program and save it to the SDRAM of PA168V Then the file can be read by PalmTool This operation aims at testing X 1 Connect to FTP Server to get the file of updating program and update program Flash This operation aims at updating program X 2 Connect to FTP Server to get the file of updating dial rules and update program Flash This operation aims at updating dial rule Note When you use ftp 0 and ftp 1 commands if the file get from FTP server is too large or the net speed is too slow then the process will not be seen in telnet window Please be patient Using ftp command in telnet to get file spends almost same minutes as getting file using PA168V So if nothing is displayed after too long time it means that ftp is fail Note All the Telnet commands of PA168V FXS gateway should be written in low case and the password is case sensitive Beijing Centrality Communication Inc 43 PA168V SIP FXS Gateway User Manual V1 42 gt Operation of PA168V FXS gateway gt Receiving a call When a call incomeing whether from IP net work or PSTN all the ordinary phones linked with the FXS jacks
25. r enable PA168V to enter into the setup mode Details refer to the following table Keys Functions 1 With handset of the ordinary telephone lined to FXS port hung press SET SET key to indicate local IP address with voice prompt 2 With handset of the ordinary telephone lined to FXS port hung push on 1234 X SET the default password and then input numbers X SET button to set different the connect network type X ranges from 0 to 3 Beijing Centrality Communication Inc 8 PA168V SIP FXS Gateway User Manual V1 42 0 static IP 1 DHCP 2 PPPoE 3 modem 3 With handset of the ordinary telephone lined to FXS port hung push on 1234 SET the default password and then press SET button enable the gateway to enter into the setup mode 4 With handset of the ordinary telephone lined to FXS port hung push on 1234 XXX XXX XXX XXX the default password and input purpose static IP address SET XXX XXXX XXX XXX then press the SET button Use the key on the keyboard of an ordinary telephone to replace After the presetting as mentioned above PA168V has acquired the related network parameter You can make specific settings on the PC Note If PA168V has been set in the double modes and PSTN First please first tap down the hook or press the flash key shift to the IP mode then conduct the operation above gt Configuration with the
26. r dialnum selected in use dialplan drop down Beijing Centrality Communication Inc 14 PA168V SIP FXS Gateway User Manual V1 42 list set area code according to E 164 dial rule For example Beijing is 10 Shanghai is 21 e idd code With enable or dialnum selected in use dialplan drop down list set country code according to E 164 dial rule For example China is 86 U S A is1 e idd prefix With enable or dialnum selected in use dialplan drop down list set international call prefix according to E 164 dial rule such as 00 e ddd prefix With enable or dialnum selected in use dialplan drop down list set long distance call prefix according to E 164 dial rule such as 0 Note With dialnum seletcted in use dialplan drop down list you can also set dddcode iddcode iddprefix and dddprefix according to requirement of system e innerline Enable disable innerline call by selecting corresponding items from dropdown list a disable Disable call innerline by selecting this item enable enable call innerline by selecting this item e innerlineprefix With enable selected in innerline dropdown list please fill the number prefix to pick up innerline such as 0 e Call waiting Enable disable call waiting by checking unchecking the box e forward number Enter receiving forwarded calls phone number into this Beijing Centrality Communication Inc 15 PA168V SIP FXS Gateway User Manual V1 42 field If the IP phone used w
27. r here e mac MAC address is the physical address supplied by the Ethernet NIC Every PA168V FXS Gateway is preset while shipped from the factory with a unique algorism MAC address printed on the back of the base Audio settings Audio Settings codecl e729 gt codec2 27231 gt codec3 feTl1u z codec4 eTlla gt codecS esn gt codec null vad IV age Cj aec IV audio frames jitter size fo g 723 1 high rate Vv Fig 3 3Audio Setting Beijing Centrality Communication Inc 12 PA168V SIP FXS Gateway User Manual V1 42 codec1 Set the priority 1 of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm codec2 Set the priority 2 of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm codec3 Set the priority 3 of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm codec4 Set the priority 4 of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm codec5 Set the priority 5 of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm codec6 Set the priority 6 of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm vad Enable disable VAD voice activity detection agc Enable disable AGC aec Enable disable VEC audio frame Set audio frames in RTP package Minimum is 1 and maximum is 8 jitter size
28. rading and configuration m Use FTP server FTP server can be supplied by the service provider as well as setup by the users in LAN Please set the IP address or domain name of FTP server to PA168V FXS gateway relevant field As to the related operations of centralize upgrade and configuration please refer to the following table step operation Operation illustration Pick up the handset enter the default password then press SET button 1 1234 SET and the PA158V will enter the setup mode In the setup mode PA168V will be linked to FTP server to get the 2 8 SET firmware and upgrade In the setup mode PA168V will be linked to FTP server to get the 3 5 SET configuration file and upgrade Beijing Centrality Communication Inc 46 PA168V SIP FXS Gateway User Manual V1 42 In the setup mode PA168V will be linked to FTP server to get the 4 6 SET dialplan rule file and upgrade Note Please do NOT change the name of the upgrading files or the upgrading will fail Use Telnet command to upgrade Use telnet connect to PA168V Please use the supper password to log in and then start the upgrading with FTP X command X ranges from 0 to 2 X 0 Link to the FTP Server to get the firmware and save the files to the sadram of the PA168V The files can be read with Palmtool and are used for debug x 1 Link to the FTP Server to get the firmware and
29. reee Phone Settings ee dialplan 1 enable dddcode 10 iddcode 86 iddprefix 00 dddprefix 0 innerline 1 enable innerlineprefix 0 callwaiting 1 enable fwdnumber 82378009 fwdpoweroff 1 enable fwdalways i enable fwdbusy 1 enable fwdnoanswer 1 enable answer 30 digitmap 1 enable handsetin 5 handsetout 20 ringtype O dtmf speakerout 20 speakerin 1 reee Other Settings ee password 1234 upgradetype O disable upgradeaddr empty sntpip 0 0 0 0 daylight O disable Beijing Centrality Communication Inc 29 PA168V SIP FXS Gateway User Manual V1 42 timezone 55 GMT 08 00 Beijing Hong Kong Urumgi Command set Syntax description set keywords value Usage Used to configure password and other running parameters of PA168V FXS gateway Detailed description set iptype X Set how PA168V FXS gateway gets relevant network parameters X ranged from 0 through 3 0 authorize users set IP address subnet mask and router IP address of PA168V manually 1 use DHCP mode With this system 2 use PPPoE mode Those ADSL and Cable Modem users please select this item 3 use modem mode Those who use PA168V with modem please set the value as 3 set pppid XXX With iptype set as 2 use this command to set user name of PPPoE with iptype set as 3 use this command to set user name of dial up network set ppppin XXX With iptype set as 2 use this command to set user name of PPPoE with iptype set as 3 use this command to set user name of dial up net
30. scription of PA168V Telnet commands Command Syntax description No optional parameter Usage Type command name and parameters following P gt Be used as the keyword to supply keyword and parameters of the relevant commands Relevant usage None Detailed description List help of all commands For example P gt set get list settings store x store current to xth settings load x load xth settings to current exit write save settings Beijing Centrality Communication Inc 27 PA168V SIP FXS Gateway User Manual V1 42 Command get Syntax description No optional parameter of keywords Usage Display basic parameters of the PA168V FXS gateway Relevant usage None Detailed description get Display basic running parameters of the PA168V FXS gateway Input ordinary password without debug being set as O disable or input super password with debug set as O disable then following parameters of PA168V FXS gateway will be displayed PA168X V1 42 settings Password P gt get Henne Network Settings iptype O static ip 192 168 1 100 subnetmask 255 255 255 0 router 192 168 1 254 dns 202 106 196 152 dns 2202 106 196 115 mac 00 09 45 65 a3 e6 sa Adio Settings codec1 0 g729 codec2 1 g7231 codec3 2 g711u codec4 3 g711a codec5 4 gsm codec6 6 null vad 1 enable agc O disable aec 1 enable audioframes 1 jittersize 0 6 3k 1 enable seee Phone Settings ree dialplan 1 enable dddcode 10 iddcode 86 iddpref
31. sipphone Free SIP service please visit www sipphone com for Beijing Centrality Communication Inc 18 PA168V SIP FXS Gateway User Manual V1 42 more information e ngtel Use NGTEL s SIP system e ayctel Use Ayctel s SIP system e sip proxy If use service is checked please set the URI domain name IP address service port of the SIP proxy server into sip proxy The default service port is 5060 When the default service port is used service port can be omitted If the system has an Outbound Proxy please set the URI of the Outbound proxy into sip proxy and set the domain name of SIP proxy server into domain realm If use service is not checked please clear sip proxy and domain realm e domain realm Set the domain name of the SIP proxy server e nat traversal When PA168V gateway with private IP address need communicate with other PA168V gateway in a different LAN or on Internet please select an item from dropdown list a disable Select this item when the sip proxy server and PA168V gateway in the same LAN or the sip proxy system supports PA168V Beijing Centrality Communication Inc 19 PA168V SIP FXS Gateway User Manual V1 42 gateway working behind the LAN enable When the system does not support PA168V gateway working behind the LAN please select this item to search public IP address of the NAT device With this item selected nat ad
32. sipphone con nat traversal disable gt nat addr aaa nat ttl p phone number 8870054 secot e8700 O oin fesor register port E060 rtp port i726 rtp tos p call type advanced dtmf inband audio 7 dtmf payload fior super password 12345678 debug foutput x Fig 3 5 Protocol Setting e use service Enable disable service by checking clearing this box To make calls through SIP Proxy Server please check this box otherwise PA168V can only make IP to IP calls e register ttl PA168V will send a keep alive registration message to SIP proxy server every register ttl seconds The minimum value is 10 maximum value is 65535 Default is 60 e service type This option is used to accommodate the miscellaneous requirements of the system providers Beijing Centrality Communication Inc 17 PA168V SIP FXS Gateway User Manual V1 42 e Common no special requirements e Huawei Use Huawei s system e zte Use ZTE s SIP system e harbour Use Harbour s system e utstarcom Use UtstarCom s SIP system e uptech Use Uptech s system e keimen Use Keimen s system e mediaring Use Mediaring s SIP system e italkbb Use ItalkBB s SIP system e stanaphone Use Stanaphone s SIP system e net2phone Use Net2phone s SIP system e Fwd Free SIP service please visit www freeworldialup com for more information e Inphonex Free SIP service please visit www inphonex com for more information e
33. t Installation PA168V SIP FXS gateway adopts the standard RJ45 Ethernet connectors which are put in use in cases that Ethernet Jack is used such as those of users of LAN Ethernet ADSL or Cable Modem 1 Connect to telephones Connect the ordinary telephone to the PA168V FXS jack with a RJ11 connect cable 2 Connect to PSTN Connect the PSTN line to the PSTN jack of PA168V Note When power off use ordinary telephones to make or receive a PSTN call to confirm PSTN line works well 3 Link to the network Plug one end of the RJ45 skips cable into the NET WORK marked RJ45 connector by of PA168V Link the other end to the Beijing Centrality Communication Inc 7 PA168V SIP FXS Gateway User Manual V1 42 HUB or switch or RJ45 connector of ADSL or Cable Modem 4 Link to the PC Plug one end of the RJ45 skips cable into the PC marked RJ45 connector of PA168V Link the other end to the RJ45 connector of PC NIC optional 5 Power on plug the power cord adapter into the Power Jack at the back of the PA168V Then plug the other end of the power cord adapter into the appropriate wall outlet gt Configuration Two ways of configuring the PA168V SIP FXS gateway are available web browser Telnet commands gt Preset the PA168V by Using ordinary telephone keyboard Use the keyboard of an ordinary telephone which has been linked to the PA168V FXS together with the set button to make the presetting o
34. ted because it will increase the risk of upgrading the wrong firmware into PA168V gateway Other settings Other Settings password 1234 upgrade type disable X upgrade addr l sntp ip jo 0 0 0 use daylight D timezone GMT 08 00 Beijing Hong Kong Urumqi Ne Save Settings ddress Book Upgrade Firmware Fig 3 6 Other Setting Beijing Centrality Communication Inc 22 PA168V SIP FXS Gateway User Manual V1 42 e password Set the ordinary password of PA168V Default is 1234 e upgradetype Set the auto upgrade type of the PA168V FXS gateway a disable Disable auto upgrade a all pa168V will find matching firmware binary file and configuration file of the hardware type only at the FTP server specify by upgradeaddr item a mac pa168V will find matching firmware binary file and configuration file of the MAC address only at the FTP server specify by upgradeadadr item ppp id pa168V will find matching firmware binary file and configuration file of the ppp id only at the FTP server specify by upgradeadadr item account pa168V will find matching firmware binary file and configuration file of the account only at the FTP server specify by upgradeaddr item phonenumber pa168V will find matching firmware binary file and configuration file of the phone number only at the FTP server specify by upgradeadar item e upgrade addr Put IP address or domain name obtained by ISP of FTP server supplying upgrade progr
35. telephone network Use the same way as the dialing of a PSTN call Make a call with IP network Tap the hook or press the Flash key on an ordinary phone and switch PA168V to the network from PSTN After hearing the dial tone you can make a call in different ways Please refer to the part of make a call in When the dual mode of the PA168V is disable gt When the dual mode of the PA168V is set as IP first Make a call with IP network When PA168V is set as IP first and while you pick up the handset it will be linked to the IP network After hearing the dial tone you can make a call in different ways Please refer to the part of make a call in When the dual mode of the PA168V is disable Make a call with PSTN line Dial the prefix number of the preseting Dual mode prefix PA168V will be switched to PSTN After hearing the dial tone dial the phone number then make a call gt Emergency call Beijing Centrality Communication Inc 45 PA168V SIP FXS Gateway User Manual V1 42 When PA168V is power cut or failed the ordinary phone on the PA168V FXS jacks will be linked directly to the PSTN to make a life line for the purpose of emergency call gt Centralize Upgrade and configuration of PA168V FXS gateway gt Prepare firmware and configuration file Please ask the latest version of upgrade program from the agents or suppliers Or visit http www aredfox com download gt Manual upg
36. ugh 224 set calltype X Set call type of PA168V gateway X is ranged from 0 through 1 0 when SIP systems not support outbound proxy 1 when SIP Beijing Centrality Communication Inc 39 PA168V SIP FXS Gateway User Manual V1 42 systems not support outbound proxy set dtmf X Set DTMF relay type X is ranged form 0 through 2 0 inband audio 1 rfc 2833 2 sip info set dtmf payload X When dtmf X select 1 rfc 2833 This parameter can be used indicating type of RTP payload type The value can be use integer 96 101 set password XXXX Set password of the PA168V FXS gateway XXX must be ASCII characters set superpassword XXXX Set super password of the PA168V FXS gateway XXX must be ASCII characters set debug X Set open debugging message output grade for special tool X is ranged from 0 through 5 0 close debugging output 1 output the operation information to the window 2 output all the bug information and data in test window 3 save the bug information into SDRAM 4 disable checks the mark Beijing Centrality Communication Inc 40 PA168V SIP FXS Gateway User Manual V1 42 set upgradetype X Set auto upgrade matching type X is range from O through 5 0 disable 1 all 2 mac 3 ppp id 4 account set upgradeaddr XXX XXX XXX XXXK Set IP address or domain name of FTP server supplying upgraded program of PA168V gateway set ntsip XXX XXX XXX XXXK Set
37. upgraded as in the new configuration files gt Recover the factory setting If you want to recover the default parameters setting please pick up the handset and input the ordinary password default is 1234 Then press the SET button at the back end of PA168V and PA168V will then enter into the setup mode In the setup mood after press 5 5 PA168V will restart and the factory setting is recovered Beijing Centrality Communication Inc 49 PA168V SIP FXS Gateway User Manual V1 42 Reserves the right to make changes in technical and product specification without prior notice PA168V SIP FXS Gateway User Manual V1 42 Copyright 2003 2005 Beijing Centrality Communication Inc All rights reserved Beijing Centrality Communication Inc 50
38. v register ttl service type common sip proxy fine sipphone con domain realm fiw sipphone con nat traversal disable nat addr a nat ttl phone number fas70054 ooo account estoos ts pin jaisees077 Cs register port fo06o rtp port fi726 rtp tos call type advanced z dtmf inband audio dtmf payload 101 super password 12345678 debug foutput x Other Settings password 1234 upgrade type disable upgrade addr sntp ip o 0 0 0 use daylight Vv timezone GNT 08 00 Pacific Time U S amp Canada ed Save Settings Address Book Upgrade Firmware Fig 3 1 Http Setting T T 3 A Network Setting Network Settings iptype static gt ppp id ppp pin OoOO O local ip 192 168 1 100 subnet mask 255 255 255 0 router ip 192 168 1 254 dns 202 106 46 151 dns2 202 96 128 68 mac 00 0d ea 00 00 03 Fig 3 2 Network Setting e iptype Set how PA168V FXS Gateway gets relevant network parameters Beijing Centrality Communication Inc 10 PA168V SIP FXS Gateway User Manual V1 42 by selecting corresponding item from drop down list static ip Select this item to authorize users to set IP address subnet mask router IP address and dns IP of PA168V FXS gateway manually m dhcp Select this item to enable DHCP mode and it will assign the IP address and other net parameters automatically m pppoe Those ADSL Cable Modem and Ether net users who take the way of virtual dial up please
39. work Beijing Centrality Communication Inc 30 PA168V SIP FXS Gateway User Manual V1 42 set ip XXX XXX XXX XXX With iptype set as 0 use this command to set IP address of PA168V FXS gateway set subnetmask XXX XXX XXX XXXK With iptype set as 0 use this command to set subnet mask of PA168V FXS gateway set router XXX XXX XXX XXX With iptype set as 0 use this command to set router IP of network set dns XXX XXX XXX XXX With iptype set as 0 use this command to set IP address of DNS server set dns2 XXX XXX XXX XXX With iptype set as 0 use this command to set IP of backup DNS server set mac XX XX XX XX KXX KX Set MAC address of the PA168V FXS gateway Parameter XX XX XX XX XX XX Must be an HEX number set codec1 X Set the priority 1of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec2 X Beijing Centrality Communication Inc 31 PA168V SIP FXS Gateway User Manual V1 42 Set the priority 2 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec3 X Set the priority 3 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec4 X Set the priority 4 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codecd X Set the priority 5 of the audio compression algorithm X is
Download Pdf Manuals
Related Search