ThinMan Toolkit User Manual
Contents
1. Add a firmware on the USB drive mandatory Add a ThinMan Template Configuration tplx optionally Add a licenses file fic optionally The template file is imported into the USB Storage Key Page 27 of 57 Praim Toolkit Guide we You can remove a template from the USB Storage Key clicking on Remove Template You can remove a firmware from the USB Storage Key clicking on Remove Firmware V Enable Override ThinMan Address IP Hostname DHCP Option ThinMan Address IP Hostname when DHCP option not available 192 168 0 100 Clicking on Set override will open this window that allows to override the ThinMan Address configuration contained in the template This option will overwrite on the USB Key the options configured in the loaded template Click OK to confirm these changes Click on Finish to close the software then you can disconnect the USB Storage Key from the PC To recover a thin client using the prepared USB Key follow the procedure explained at Use the Recovery USB Key on a Thin Client see page 47 paragraph Page 28 of 57 we Praim Toolkit 1 2 5 4 Cloning a ThinOX device using a USB Key It is possible to use a prepared USB Key to clone a ThinOX device In this way you can extract a thin client image and save it on a USB Key then it is possible to use this USB Key to write the previously saved image on new thin clients WARNING This procedure is2. Documents Music Computer b 4 4 d ThinClientToolkit Network BIOS USB Update Online Documentation Control Panel ThinOX USB Recovery USB Drive Copier Windows Embedded USB Recove di ThinMan a ThinMan Remote Console Devices and Printers Administrative Tools gt Run Shut down ica Run Windows Embedded USB Recovery software Page 42 of 57 Type Standard Praim Toolkit 1 2 5 Insert a USB drive Select the USB drive Select the format option Format as USB Recovery Format for device cloning Select from the list the inserted USB Storage Key Click on Format for device cloning Warning All data on device will be lost Are you sure you want continue Conform the operation clicking on Yes Page 43 of 57 Praim Toolkit Guide A Toolkit Formatting Wait a few seconds Insert a USB drive Don t remove the USB drive Select the USB drive Select the format option Format as USB Recovery The window will show the operation in progress Wait until it finished and click OK Page 44 of 57 we Praim Toolkit 1 2 5 PRAIM device doning Insert a USB drive Select the USB drive Select the format option Format as USB Recovery Format as simple drive Click on Finish to close the software Detach the
3. A Toolkit Formatting Wait a few seconds Insert a USB drive Don t remove the USB drive Select the USB drive Select the format option Format as USB Recovery Wait until it finished and click OK Page 32 of 57 we Praim Toolkit 1 2 5 PRAIM device doning Insert a USB drive Select the USB drive Select the format option Format as USB Recovery Format as simple drive Click on Finish to continue Detach the USB Key from the PC use the Windows procedure to safely remove the USB Key The USB Key is now ready to extract and save on itself the thin client DOM Disk On Module image Use the USB Key as explained in the Use the Recovery USB Key on a Thin Client see page 47 paragraph on the master configured thin client to extract its DOM Disk On Module image Once the USB Key has read a thin client DOM image you can use it on other thin clients to write the saved image The procedure is the same as explained in Use the Recovery USB Key on a Thin Client see page 47 paragraph with the only exception that a confirmation is required press y and Enter on the keyboard when requested to proceed with the writing Page 33 of 57 Praim Toolkit Guide EA WARNING This operation will clone the first thin client firmware and configuration on all the other thin clients Pay attention because also the license the hostname and t
4. Peripherals and press lt Enter gt on the keyboard From the Integrated Peripheral menu select USB Device Setting and press lt Enter gt On the menu you will see the inserted USB Key with Auto Mode option enabled Select the inserted USB Key and press lt Enter gt On the menu select FDD mode and press lt Enter gt Press lt ESC gt twice to return on the BIOS menu Press lt F10 gt and on the request to save press lt Y gt or lt Enter gt The BIOS configuration is saved Page 54 of 57 P Praim Toolkit 1 2 5 8 5 Procedure for Ultra Series On the thin client insert a USB Key Power on the device and while it is starting access the BIOS configuration pressing on lt DEL gt key On the BIOS menu select Advanced BIOS Features option use the arrow key on the keyboard and press lt Enter gt On the Advanced BIOS Features menu select First Boot Device and press lt Enter gt From the First Boot Device menu select USB ZIP and press lt Enter gt Press lt ESC gt to return on the BIOS menu Select Integrated Peripherals and press lt Enter gt on the keyboard From the Integrated Peripheral menu select USB Device Setting and press lt Enter gt On the menu you will see the inserted USB Key with Auto Mode option enabled Select the inserted USB Key and press lt Enter gt On the menu select FDD mode and press lt Enter gt Press lt ESC gt twice to return on the BIOS menu Press lt F10 gt a
5. and then lt ENTER gt to save the configuration and exit the BIOS setup window this will reboot the thin client The thin client will reboot using the USB Key as boot device This configuration is not saved in the BIOS but every time you need to boot from USB device you have to follow the procedure explained above Page 49 of 57 Praim Toolkit Guide te 8 How to configure BIOS to boot always from a USB Key first To allow the thin client to boot always from USB Key first you have to change its BIOS configuration The procedure is slightly different and depend on the thin client hardware Page 50 of 57 Da Praim Toolkit 1 2 5 8 1 Procedure for Ultra Dual Core Series It is not possible to configure U9xxx thin client model to boot always from the USB Key Every time you need to boot from a USB Key you have to follow the procedure explained at chapter Booting from USB Key for U9xxx and A9xxx thin client model see page 49 Page 51 of 57 Praim Toolkit Guide te 8 2 Procedure for Atom Dual Core Series It is not possible to configure A9xxx thin client model to boot always from the USB Key Every time you need to boot from a USB Key you have to follow the procedure explained at chapter Booting from USB Key for U9xxx and A9xxx thin client model see page 49 Page 52 of 57 P Praim Toolkit 1 2 5 8 3 Procedure for Compact Dual Core Series On the thin client insert a USB Key Power on the device and while it is starting access
6. the BIOS configuration pressing on lt DEL gt key On the BIOS menu select Advanced BIOS Features option use the arrow key on the keyboard and press lt Enter gt On the Advanced BIOS Fetaures menu select First Boot Device and press lt Enter gt From the First Boot Device menu select Removable and press lt Enter gt Press lt ESC gt to return on the BIOS menu Select Integrated Peripherals and press lt Enter gt on the keyboard From the Integrated Peripheral menu select USB Device Setting and press lt Enter gt On the menu you will see the inserted USB Key with Auto Mode option enabled Select the inserted USB Key and press lt Enter gt On the menu select FDD mode and press lt Enter gt Press lt ESC gt twice to return on the BIOS menu Press lt F10 gt and on the request to save press lt Y gt or lt Enter gt The BIOS configuration is saved Page 53 of 57 Praim Toolkit Guide te 8 4 Procedure for Atomino Series On the thin client insert a USB Key Power on the device and while it is starting access the BIOS configuration pressing on lt DEL gt key On the BIOS menu select Advanced BIOS Features option use the arrow key on the keyboard and press lt Enter gt On the Advanced BIOS Features menu select First Boot Device and press lt Enter gt From the First Boot Device menu select USB ZIP and press lt Enter gt Press lt ESC gt to return on the BIOS menu Select Integrated
7. Next to continue It is possible to print the agreement by clicking on Print Page 9 of 57 Praim Toolkit Guide ie Customer Information Please enter your information Company Name PRAIM T 5 Type the User and Company Name Click Next to continue Page 10 of 57 ye Praim Toolkit 1 2 5 Choose Destination Location Select folder where setup will install files ERE C Program Files mT hinClientT oolkit You may choose a different directory where to install the software by clicking on Change Click Next to proceed with the operation Page 11 of 57 Praim Toolkit Guide ie Select Features Select the features setup will install Select the features you want to install and d ct the features you do not want to install PRAIM Windows Embedded USB Recovery of space required on the C driv 02 MB of space available on the C drive Select which components has to be installed Click Next to continue Page 12 of 57 ye Praim Toolkit 1 2 5 Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation change any of your installation settings click Back Click Cancel to exit the Click Install to begin the installation By clicking on Back is still possible to change the settings entered so far Page 13 of 57 Praim Toolkit Guide ie Setup Status The InstallShield Wizard is installing ThinClientT oolkit A
8. USB Storage Key from the PC use the Windows procedure to safely remove the USB Key The USB Key is now ready to extract and save on itself the thin client DOM Disk On Module image Use the USB Key as explained in the Use the Recovery USB Key on a Thin Client see page 47 paragraph on the master configured thin client to extract its DOM Disk On Module image Once the USB Key has read a thin client DOM image you can use it on other thin clients to write the saved image WARNING Before restoring a Windows Embedded thin client be sure to power it on and verify that the thin client is visible in the ThinMan console If the device is visible on ThinMan its license is saved so when the recovery phase is terminated the device will restore correctly its license If the thin client is not shown on the ThinMan console its license has to be entered manually Page 45 of 57 Praim Toolkit Guide te The procedure is the same as explained in Use the Recovery USB Key on a Thin Client see page 47 paragraph with the only exception that a confirmation is required press y and Enter on the keyboard when requested to proceed with the writing A NOTE At the end of writing the thin client will reboot Leave the thin client untouched and wail It will execute a recovery phase and it will reboot once or twice Page 46 of 57 we Praim Toolkit 1 2 5 7 Use the Recovery USB Key on a Thin Client Once the Recovery USB Key is pre
9. age 39 of 57 Praim Toolkit Guide ie x Toolkit 200 of 956 Mb copied Don t remove the USB drive Add a firmware on the USB drive mandatory Add a ThinMan Template Configuration tplx optionally Add a licenses file fic optionally Wait until the software is writing the selected firmware on the USB Storage Key DO NOT REMOVE the USB key from the PC until this operation is terminated Page 40 of 57 ye Praim Toolkit 1 2 5 Type Version FACTORY Unknown Add a firmware on the USB drive mandatory Add a ThinMan Template Configuration tplx optionally Add a licenses file fic optionally Click on Finish to close the software and detach the USB Storage Key from the PC To recover a thin client using the prepared USB Key follow the procedure explained at Use the Recovery USB Key on a Thin Client paragraph Page 41 of 57 Praim Toolkit Guide te 6 Cloning a Windows Embedded device using a USB Key It is possible to use a prepared USB Key to clone a Windows Embedded device In this way you can extract a thin client image and save it on a USB Key then it is possible to use this USB Key to write the previously saved image on new thin clients The first step is to prepare the key in the cloning mode Connect an empty USB Storage Key to the Windows 7 PC Whether the USB Storage Key is not empty you will lose all the data inside it
10. age Key DO NOT REMOVE the USB key from the PC until this operation is terminated Page 25 of 57 Praim Toolkit Guide ie Type Version FACTORY 8 7 3 Add a firmware on the USB drive mandatory Add a ThinMan Template Configuration tplx optionally Add a licenses file fic optionally Click on Finish to close the software and detach the USB Storage Key from the PC Clicking on Remove Firmware will delete the firmware from the USB Storage Key You may use this feature after restoring the thin client firmware From this window you can also add a ThinOX Template file that will be inserted as thin client configuration in the USB Storage Key For more information on Template file please refer to the ThinMan User Guide Click on Add Template Page 26 of 57 ye Praim Toolkit 1 2 5 D m Volume C Program Files Praim ThinMan Template X Search Template Organize v New folder D GlobalBackup Name Date modified Type Ji Log d Naming p PrivateCommands Bp Repository p Repository_Ppd p Resources p SchedulReport p Server J SNMP a Template J TMBS e L ThinOX_Template tpht 05 02 2013 14 39 TPLXT File File name ThinOX_Template tpht v ThinOXx template tplxt Select the ThinOX Template file using the browsing windows and click Open Toolkit FACTORY 8 7 3 ThinOX_Template tplxt
11. cking on Yes Page 36 of 57 ye Praim Toolkit 1 2 5 A Toolkit Formatting Wait a few seconds Insert a USB drive Don t remove the USB drive Select the USB drive Select the format option Format as USB Recovery Wait until it finished and click OK Page 37 of 57 Praim Toolkit Guide ae Type PRAIM USB Recovery Insert a USB drive Select the USB drive Select the format option Click on Next to continue Page 38 of 57 we Praim Toolkit 1 2 5 Add a firmware on the USB drive mandatory Add a ThinMan Template Configuration tplx optionally Add a licenses file fic optionally Click on Add Firmware to select the Windows Embedded firmware file ae i firmware v earch firmw D a a fi 4 S fi Organize v New folder x TNE Name Date modified Type E Desktop _ 1gb cmxpf 12 04 2012 17 00 CMXPF File ih Downloads Hie m 01 02 2013 15 15 CMXPF File Le Photo Stream Recent Places a Libraries amp Apps Documents iE My Documents B Public Documents al Music ball lt P File name 1gb cmxpf Windows Factory File crmxpf Windows Backup File cmxpb Windows Clone File cmxpc You can choose between Factory Backup and Clone file type from the list on the right Then select the firmware file from the explorer window and click Open P
12. d and press lt Enter gt On the Advanced BIOS Features menu select First Boot Device and press lt Enter gt From the First Boot Device menu select USB ZIP and press lt Enter gt Press lt ESC gt to return on the BIOS menu Select Integrated Peripherals and press lt Enter gt on the keyboard From the Integrated Peripheral menu select USB Device Setting and press lt Enter gt On the menu you will see the inserted USB Key with Auto Mode option enabled Select the inserted USB Key and press lt Enter gt On the menu select FDD mode and press lt Enter gt Press lt ESC gt twice to return on the BIOS menu Press lt F10 gt and on the request to save press lt Y gt or lt Enter gt The BIOS configuration is saved Page 57 of 57
13. destructive on the destination thin clients It will remove the thin client license and you have to contact the Praim Support to obtain the correct one Instead to use this procedure try to restore the thin client using the recovery procedure see How to create Recovery USB Key for ThinOX see page 20 for more informations The first step is to prepare the key in the cloning mode Connect an empty USB Storage Key to the Windows 7 PC Whether the USB Storage Key is not empty you will lose all the data inside it Page 29 of 57 Praim Toolkit Guide te Documents Music Computer hb 4 4 J ThinClientToolkit Network b BIOS USB Update Online Documentation ThinOX USB Recovery Control Panel Devices and Printers USB Drive Copier Windows Embedded USB Recove di ThinMan di ThinMan Remote Console Administrative Tools gt Run Run ThinOX USB Recovery software Page 30 of 57 J Toolkit Praim Toolkit 1 2 5 Firmware WIN 0 Insert a USB drive Select the USB drive Select the format option Format as USB Recovery Format for device cloning Format as simple drive Select from the list the inserted USB Storage Key Click on Format for device cloning Warning All data on device will be lost Are you sure you want continue ves J Lue Confirm the operation clicking on Yes Page 31 of 57 Praim Toolkit Guide ie
14. e program default is Italiano and click OK to proceed with the installation tems to be installed on your computer Click Status Requirement Pending Microsoft Visual C 2010 Redistributable Package x86 Whether the component Microsoft Visual C 2010 Redistributable Package is not already installed on the device proceed with its installation by clicking Install the component must be installed and progress with the ThinMan setting up Page 7 of 57 Praim Toolkit Guide ie Welcome to the InstallShield Wizard for ThinClientT oolkit The InstallShie td will install ThinClientT oolkit on your computer To continue click Next j Click Next to confirm the installation Page 8 of 57 ve Praim Toolkit 1 2 5 License Agreement Please read the following license agreement carefully PRAIM Srl End User License Agreement READ THIS CAREFULLY BEFORE USING THE PRODUCT By installing or otherwise using the Software you agree to be bound by the term g of this Agreement If you do not accept these terms do not install or use the This End User License Agreement is a legal agreement between you either an individual or a single entity the Licensee and PRAIM Srl PRAIM for the PRAIM Product which include computer software printed materials electronic materials readme txt files help files etc updates and supplements provided to Read and accept the License Agreement then click
15. erties Below you can find information on how to install and remove Praim Toolkit software how to initialize the USB Memory Key for restoring a thin client how to initialize the USB Memory Key for cloning a thin client how to use the USB Memory Key on the thin client This guide is valid for thin client models belonging to Ultra Dual Core Series Atom Dual Core Series Compact Dual Core Series Atomino Series Ultra Series Compact Series Ino Series Page 4 of 57 we Praim Toolkit 1 2 5 1 1 Firmware compatibility For ThinOX thin client only firmware 8 2 x and above are suitable to be used with these procedures Page 5 of 57 Praim Toolkit Guide te 2 Installing and Removing Praim Toolkit Praim Toolkit can be installed on these supported Operating Systems in both 32 or 64 bit architecture if O S support 64 bit Windows 7 Windows 2003 Server Windows 2008 Server also SP2 All this O S can be installed on physical hardware or in a virtual machine environment In any case Praim Toolkit will run in 32 bit mode only Page 6 of 57 ie Praim Toolkit 1 2 5 2 1 Installing Praim Toolkit Run the installation file PRAIMThinClientToolkit W7 1 0 005_RC exe on the computer where you want to install Praim Toolkit The following window will appear on the display lt Select the language for the installation from the choices below English United States ka Select the appropriate language for th
16. ete Pram KTN Documentation Area Praim Toolkit Guide This document is exclusive property of Praim Srl Permission is granted to print and copy this document for noncommercial distribution Author Documentation Date 29 Oct 2013 09 48 URL http wiki praim com display PTool125 Page 1 of 57 Praim Toolkit Guide Table of Contents NOW BB W Introduction 1 1 Firmware compatibility Installing and Removing Praim Toolkit 2 1 Installing Praim Toolkit 2 2 Removing Praim Toolkit How to create Recovery USB Key for ThinOX Cloning a ThinOX device using a USB Key How to create Recovery USB Key for Windows Embedded Cloning a Windows Embedded device using a USB Key Use the Recovery USB Key on a Thin Client 7 1 Booting from USB Key for U9xxx and A9xxx thin client model How to configure BIOS to boot always from a USB Key first 8 1 Procedure for Ultra Dual Core Series 8 2 Procedure for Atom Dual Core Series 8 3 Procedure for Compact Dual Core Series 8 4 Procedure for Atomino Series 8 5 Procedure for Ultra Series 8 6 Procedure for Compact Series 8 7 Procedure for Ino Series NOW Bf 16 20 29 39 42 47 49 50 ol 52 53 54 55 56 a7 Page 2 of 57 we Praim Toolkit 1 2 5 Praim Toolkit User Guide Praim Toolkit 1 2 5 User Guide Revision 1 Date 28 October 2013 This document has been produced by Praim This guide the software and the firmware are protected under international copyright laws wi
17. f the installed software and select Praim ThinClientToolkit Click on Uninstall Skip the next step and proceed Page 16 of 57 ye Praim Toolkit 1 2 5 Welcome Modify repair or remove the program ice program This program lets you modify the Modify t new program features to add or select currently installed features to remove Il all program features installed by the previo Remove all installed features Remove running installation file Run the installation file PRAIMThinClientToolkit W7 1 0 005_RC exe on the computer where you previously installed Praim Toolkit From the window select Remove option and click Next Do you want to completely remove the selected application and all of its features Yer ute For both cases Select Yes from the dialog window to confirm the removing of the software Page 17 of 57 Praim Toolkit Guide ie Setup Status The InstallShield Wizard is removing ThinClientT oolkit A status bar will show the progress of the software removing Page 18 of 57 ye Praim Toolkit 1 2 5 Uninstall Complete InstallShield Wizard has finished uninstalling ThinClientT oolkit The software is removed Page 19 of 57 Praim Toolkit Guide te 3 How to create Recovery USB Key for ThinOx Connect an empty USB Storage Key to the Windows 7 PC Whether the USB Storage Key is not empty you will lose all the data inside it T Documents Music Compute
18. he IP Address configuration are cloned The license contained on the cloned thin clients will be not valid Contact the Praim Support to obtain the correct license So you will have all the thin clients with the same hostname remember to change it after the cloning operation Also if a static IP Address is configured on the first thin client the cloned thin clients will have the same static IP Address causing network problem Page 34 of 57 we Praim Toolkit 1 2 5 5 How to create Recovery USB Key for Windows Embedded Connect an empty USB Storage Key to the Windows 7 PC Whether the USB Storage Key is not empty you will lose all the data inside it T Documents Music Computer EREEREEREERE d ThinClientToolkit Network p BIOS USB Update Online Documentation Control Panel m ThinOX USB Recovery USB Drive Copier Windows Embedded USB Recove Ji ThinMan P ThinMan Remote Console Devices and Printers Administrative Tools gt Run Shut down gt Run Windows Embedded USB Recovery software Page 35 of 57 Praim Toolkit Guide Type Standard Insert a USB drive Select the USB drive Select the format option Format as USB Recovery Format for device cloning Select from the list the inserted USB Storage Key Click on Format as USB Recovery Warning All data on device will be lost Are you sure you want continue Conform the operation cli
19. kit Guide ae Add a firmware on the USB drive mandatory Add a ThinMan Template Configuration tplx optionally Add a licenses file fic optionally Click on Add Firmware to insert the ThinOX firmware file at ee Organize v New folder F Favorites Name Date modified ype BD Desktop F _ 9010_9 1 1 tar 26 03 2013 12 31 TAR File i Downloads _ XT9050 A_8 5 6 tar 18 09 2012 09 20 TAR File LA Photo Stream _ XT9050 A_8 6 0 tar 19 10 2012 15 04 TAR Fi _ XT9050 A_8 6 2 tar 08 11 2012 12 TAR File _ XT9050 A_8 6 3 tar 14 11 201 TAR File a Libraries _ XT9050 A_8 6 5 tar 16 01 2 8 TAR File amp Apps _ XT9050 A_8 7 0 tar 4 03 20 8 TAR File Documents _ XT9050 A_8 7 1 tar 25 03 2013 0 AR File ie C XT9050 A_8 7 2 tar 05 03 2013 15 32 TARFi E Pictures _ XT9050 A_8 7 3 tar 04 TAR Fi 327 7101 Recent Places EE Videns vies r File name XT9050 A_8 7 3 tar ThinOX Firmware tar M Goen fe canes Select the firmware file from the explorer window and click Open Page 24 of 57 ye Praim Toolkit 1 2 5 x Toolkit Part 4 of 6 Copying file 34 of 45 Don t remove the USB drive Add a firmware on the USB drive mandatory Add a ThinMan Template Configuration tplx optionally Add a licenses file fic optionally Wait until the software is writing the firmware on the USB Stor
20. nd on the request to save press lt Y gt or lt Enter gt The BIOS configuration is saved Page 55 of 57 Praim Toolkit Guide te 8 6 Procedure for Compact Series On the thin client insert a USB Key Power on the device and while it is starting access the BIOS configuration pressing on lt DEL gt key On the BIOS menu select Advanced BIOS Features option use the arrow key on the keyboard and press lt Enter gt On the Advanced BIOS Features menu select First Boot Device and press lt Enter gt From the First Boot Device menu select USB ZIP and press lt Enter gt Press lt ESC gt to return on the BIOS menu Select Integrated Peripherals and press lt Enter gt on the keyboard From the Integrated Peripheral menu select USB Device Setting and press lt Enter gt On the menu you will see the inserted USB Key with Auto Mode option enabled Select the inserted USB Key and press lt Enter gt On the menu select FDD mode and press lt Enter gt Press lt ESC gt twice to return on the BIOS menu Press lt F10 gt and on the request to save press lt Y gt or lt Enter gt The BIOS configuration is saved Page 56 of 57 P Praim Toolkit 1 2 5 8 7 Procedure for Ino Series On the thin client insert a USB Key Power on the device and while it is starting access the BIOS configuration pressing on lt DEL gt key On the BIOS menu select Advanced BIOS Features option use the arrow key on the keyboar
21. pared see How to create Recovery USB Key for ThinOX see page 20 and How to create Recovery USB Key for Windows Embedded see page 35 you can use it on a thin client Insert the USB Key in a USB Port on the thin client Power on the thin client and keep pressed F12 function key on the keyboard during the bootstrap to access the Boot Menu you can also configure the thin client to boot always from a USB key first see How to configure BIOS to boot always from a USB Key first see page 50 for more informations From the Boot Menu select using arrow keys the USB Key see box below and then press lt ENTER gt A How to select the USB Key from Boot Menu For most BIOS the USB key is available and can be selected under HARDDISK press lt ENTER gt on the keyboard and selected then USBO or similar it can be also the model name of the USB key In some cases depending on the BIOS version and manufacturer select USB ZIP from the available choice For U9xxx thin client model e g U9700 follow the instruction available in the chapther Booting from USB Key for U9xxx and A9xxx thin client model see page 49 The restore procedure will start immediately and the progress status is shown on the monitor DO NOT turn off the thin client during this phase At the end of the process a message will indicate Now remove your USB device Remove the USB Key from the thin client and it will reboot The thin client will event
22. r EREEREEREERE d ThinClientToolkit Network p BIOS USB Update Online Documentation ThinOX USB Recovery USB Drive Copier Windows Embedded USB Recove d ThinMan P ThinMan Remote Console Control Panel Devices and Printers Administrative Tools gt Run Shut down gt Run ThinOX USB Recovery software Page 20 of 57 J Toolkit Praim Toolkit 1 2 5 Firmware WIN 0 Insert a USB drive Select the USB drive Select the format option Format as USB Recovery Format for device cloning Format as simple drive Select from the list the inserted USB Storage Key Click on Format as USB Recovery Warning All data on device will be lost Are you sure you want continue ves J Lue Confirm the operation clicking on Yes Page 21 of 57 Praim Toolkit Guide A Toolkit Formatting Wait a few seconds Insert a USB drive Don t remove the USB drive Select the USB drive Select the format option Format as USB Recovery The window will show the operation in progress Wait until it finished and click OK Page 22 of 57 Type PRAIM USB Recovery Praim Toolkit 1 2 5 Insert a USB drive Select the USB drive Select the format option Format for device doning Format as simple drive Click on Next to continue Page 23 of 57 Praim Tool
23. status bar will show the progress of the installation At this point is still possible to quit the operation by clicking on Cancel Page 14 of 57 ye Praim Toolkit 1 2 5 InstallShield Wizard Complete The InstallShield Wizard has su fully installed ThinClientT oolkit Click Finish to exit the wizard The software is now installed Click Finish to end the installation Page 15 of 57 Praim Toolkit Guide ae 2 2 Removing Praim Toolkit Removing Praim Toolkit can be done in two different modes via Control Panel gt Programs and Features running the installation file PRAIMThinClientToolkit W7 1 0 005_RC exe S 3 gt Control Panel All Control Panel Items Programs and Features x Search Programs and Features Control Panel Home Uninstall or change a program View installed updates To uninstall a program select it from the list and then click Uninstall Change or Repair Turn Windows features on or Bi Organize Uninstall Change a Name Publisher Installed On Size Version Rs Praim ThinClientToolkit Praim 29 10 2012 1 00 005 Praim ThinMan Praim 13 09 2012 7 0 26 SI Praim ThinMan Remote Console Praim 12 09 2012 7 0 33 aN Praim Product version 1 00 005 Support link http www praim com Help link http www praim com L Remove via Control Panel Access the Control Panel from Windows Menu Start and then double click on Programs and Features Scroll the list o
24. th all rights reserved It s forbidden to reproduce adapt or translate this guide into any language in any form or by any means except documentation kept by the purchaser for backup purposes without explicit written permission of Praim Srl The information in this document is subject to change without notice Praim Srl makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose Further Praim Srl reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Praim Srl to notify any person of such revision or changes Unless otherwise specified all references to company names addresses and data appearing in this guide or in screenshots and examples are fictitious and is only meant to illustrate the use of the Praim product and are used only for identification or explanation and to the owner s benefit All products and or company names mentioned herein are trademarks or copyrights of their respective owners Page 3 of 57 Praim Toolkit Guide te 1 Introduction The Praim Toolkit software allows to create a USB Memory stick that can be used to restore a Praim thin client The procedure explained in this guide has to be executed only in exceptional cases and not before you have tried other ways eg put a terminal to factory default via ThinOX Terminal Prop
25. ually ask for Numero di Serie Serial Number and Codice Licenza License Code In this case write the data appearing on the monitor Model and MAC Address and contact Support Team at Praim http www praim com For Windows Embedded devices the request depend whether a ThinMan Server is on the network and the thin client already communicate with it Page 47 of 57 Praim Toolkit Guide te For ThinOX devices click Annulla on the first window then write down model and MAC Address and contact support team on Praim http www praim com Page 48 of 57 Praim Toolkit 1 2 5 7 1 Booting from USB Key for U9xxx and A9xxx thin client model For U9xxx thin client models e g U9700 A9700 it is not possible to boot always from USB Key Every time you need to boot from the USB Key you have to insert the USB Key in a USB 2 0 port USB 3 0 ports have a blue plastic insert in the middle of the port and or port is signed as SS while in USB 2 0 the insert is black power on the thin client access the BIOS window pressing continuously Del key on the keyboard at the thin client bootstrap select Boot in the upper menu using left and right arrow keys on the keyboard select Hard Drive BBS Priorities in the central window using up and down arrow keys on the keyboard press lt ENTER gt on Boot Option 1 and from the list select USB FLASH DRIVE PMAP press lt ENTER gt to confirm choice press lt F4 gt key on the keyboard
Download Pdf Manuals
Related Search