Preset 10 Architectural Two User Manual
Contents
1. LA E le POWER DMX OUTPUT DMX INPUT TB 1 TB 2 Preset 10 Architectural Two INSTALLATION WIRING INFORMATION The Preset 10 Architectural Two uses daisy chain wiring topology one station s output feeds the next station s input Its predecessor the Preset 10A had only a single DMX in out connector input and output were married together on the same three terminals The Preset 10 Architectural Two has two plug in terminal connectors a 3 pin DMX input connector TB2 and a 5 pin DMX output power connector TB1 DMX512 wiring requires cable suitable for carrying high speed digital data Specifications for this wire are 120 Ohm characteristic impedance with capacitance of less than 20pF per foot Most cables specified for the following uses are acceptable RS 422 EIA 422 RS 485 EIA 485 DMX512 CAT 5 CAT 5e CAT 6 or better It is not recommended to mix CAT cables and shielded twist pair cables on the same physical run Eighteen gauge stranded wire is suggested for power supply wiring Larger wire may be used for long runs or for mechanical strength The terminals will accept up to 12 gauge Smaller wire may be used for short runs The minimum recommended wire size is 24 gauge CAT cable is 24 gauge The chart below shows maximum distances between the power supply and a single Preset 10 for various wire sizes and popular power supply voltages Systems containing two Preset 10s a single power supply should cut these dista2. NS tort 4 DIMMERS CABLE USE 120 Ohm Data Cable Shield Common 1 Belden 9829 or White Blue Stripe 5 Pin XLR Plate TB2 2 Data Equivalent Blue White Stripe PRE10 A2 Master TB2 3 Data 2 18 AWG Black Common TB1 4 Supply 2 s Wires Red Power supply Power TB1 5 Supply hot 120 Ohm Data Cable Shield TB1 1 Common 3 Belden 9829 or White Blue PRE10 A2 Master TB1 2 Dimmer Cabinet Data Equivalent Blue White Stripe TB1 3 Data Multi Master Note Place in HTP mode Remove JP5 12 OVAC DIMMERS CABLE COLOR FROM TO USE 120 Ohm Data Cable Shield Pin 1 2 1 1 Belden 9829 or White Blue Stripe 5 Pin XLR Plate Pin 2 2 2 Data Equivalent Blue White Stripe Pin 3 Arter econ ETP oom 1 2 18 AWG Black Power Supply Common TB1 4 Supply Stranded Wires Red Power TB1 5 Supply hot 120 Ohm Data Cable Shield TB1 1 TB2 1 Common 3 Belden 9829 or White Blue Stripe PRE10 A2 Master 1B1 2 PRE10 A2 Master 1B2 2 Data Equivalent Blue White Stripe Room 1 TB1 3 2 TB2 3 Data 2 18 AWG Black TB1 4 1 4 Supply Stranded Wires Red TB1 5 TB1 5 Supply hot 120 Ohm Data Cable Shield PRE10 A2 Master TB1 1 5 Belden 9829 o
3. TB1 4 Supply Stranded Wires Red Supply Power TB1 5 Supply hot 120 Ohm Data Cable Shield TB1 1 TB1 1 Common 3 Belden 9829 or White Blue Stripe TB1 2 TB1 2 Data Equivalent Blue White Stripe aaa TB1 3 PRE10 A2 Slave TB1 3 Data 2 18 AWG Black TB1 4 1 4 Supply Stranded Wires Red 1 5 1 5 Supply hot Shield TB1 1 120 Ohm Data Cable 7 5 Belden 9829 or White Blue Stripe 1 2 Dimmer Cabinet E Data Equivalent Blue White Stripe TB4 3 CONFIGURATION Preset 10 Architectural Two SETUP The Preset 10 Architectural Two has six jumpers that select different modes of operation The factory default is to have all jumpers installed It is suggested that unused jumpers be stored by offsetting the jumper over just one of the pins when removed JP1 Record Lockout JP2 Master Slave JP3 Restore Hold JP4 Single station JP5 Merge off JP6 Radio buttons MASTER SELECTION When installed recording of presets is enabled When removed the TIME and RECORD buttons are disabled The position of JP1 on a SLAVE has no affect When installed the station is a MASTER The MASTER is responsible for transmitting and receiving DMX storing presets and communicating with SLAVES When removed the station is SLAVE A SLAVE communicates button presses and mimics the indicators of the MASTER When installed upon loss of DMX at its input the Preset 10 will
4. Two is placed in SLAVE mode by removing JP2 Preset 10 Architectural Two OPERATION INDICATORS GREEN LEDS ON CURRENTLY SELECTED PRESET FLASHING SETTING FADE TIME FOR THIS PRESET YELLOW FADE LED ON FADE IN PROGRESS FLASHING SETTING FADE TIME YELLOW MASTER FULL LED ON MASTER AT 100 OFF MASTER LESS THAN 100 YELLOW MASTER ZERO LED ON MASTER AT 0 OFF MASTER GREATER THAN 0 RED LED ON STATION LOCKED OUT RECEIVING DMX512 FROM EXTERNAL CONSOLE FLASHING RECORD MODE SELECTED GREEN LEDS YELLOW RED LED STATE TIME LED OFF OFF OFF NO POWER N A OFF ON RECEIVING DMX512 If in switch over mode PRESET 10 S LOCKED OUT If in merge mode Received DMX is merged with PRESET 10 signal OFF OFF FLASHING RECORD MODE ACTIVE CURRENT LOOK WILL BE STORED TO THE NEXT PRESSED PRESET FLASHING FLASHING OFF SETTING FADE TIME FOR THE SELECTED PRESET ON OFF OFF PRESET 10 TRANSMITTING DMX512 NO DMX512 INPUT ON ON OFF PRESET 10 TRANSMITTING DMX512 CURRENTLY FADING TO NEW PRESET PRESET BUTTON MASTER UP BUTTON PRESET LED GREEN 2 MASTER FULL LED YELLOW MASTER ZERO LED YELLOW FADE LED YELLOW MASTER DOWN BUTTON Master RECESSED TIME BUTTON RECESSED RECORD BUTTON SIGNAL RECORD LED RED RECORDING PRESETS 1 Set the look to be recorded using any DMX512 lighting console 2 Using a small blunt object i e paper clip press the recessed RECORD button located next to th
5. return to the preset selected prior to receipt of DMX When removed upon loss of DMX at its input the Preset 10 will hold the last received DMX levels until a PRESET button is pressed When installed the station is prevented from communicating with SLAVE units Slave communication uses Alternate Start Code messages Some poorly implemented DMX512 devices fail to ignore these messages resulting in flicker To reduce troubleshooting calls slave communication defaults to off When removed slave communication is enabled When installed the Preset 10 does not merge the incoming DMX with the presets Instead if there is a DMX input the levels are passed directly to the DMX output When removed if there is a DMX input it is merged with the output of the Preset 10 in a Highest Takes Precedence HTP manner When installed the PRESET buttons act like radio buttons selecting a new preset cancels the current preset When removed the PRESET buttons act in a push on push off manner all selected presets pile on to each other in a Highest Takes Precedence HTP manner All systems contain at least one MASTER Jumper JP4 is installed default condition for normal MASTER operation In systems that contain SLAVES jumperJP4 must be removed This enables MASTER SLAVE communication SLAVE SELECTION SLAVE stations communicate button presses to the MASTER and MASTER stations communicate indicator status to the SLAVES A Preset 10 Architectural
6. 3 DMX512 data input 1 C DMX512 common 2 DMX512 data output 3 DMX512 data output 4 C Supply common internally tied to pin1 5 V Supply voltage hot ESD protected EIA 485 transceiver LT1785 Ten green Preset LEDs One yellow Master at full LED One yellow Master at zero LED One yellow Fade LED One red Signal Record LED Ten Preset buttons One Master Up button One Master Down button One recessed Record button One recessed Time button For a single station installation all jumpers should be installed INSTALLED REMOVED JP1 Recording Enabled Recording Disabled JP2 Master Station Slave Station JP3 Fade to last active preset Hold Last Look JP4 Single Station Mode Multi Station Mode JP5 Switch over Mode Highest Takes Precedence HTP Mode JP6 Radio button Mode Push On Push Off Mode 9 to 24 volts DC or 10 to 16 volts AC 200mA per station A 10 volt class 2 doorbell transformer works nicely Black anodized with laser engraved nomenclature Faceplate 4 5 h X 4 6 w X 0 2 d Faceplate rear inset 4 15 h X 4 25 w X 0 1 d Electrical box minimum inside dimensions 3 6 h X 2 9 w X 1 26 d gt 1 sy 3 5 m o01 s00 JP1 JP3 lt lt gt gt TT 02 700 o op4 900 H JP4 JP6 ops 800 3 3 p 2 8 4 15 o 05 OFFLIO h
7. DOUG FLEENOR DESIGN PRESET TEN ARCHITECTURAL TWO OWNERS MANUAL model PRE10 A2 Doug Fleenor Design 396 Corbett Canyon Road Arroyo Grande CA 93420 805 481 9599 2 Serial 08B001 DOUG FLEENOR DESIGN PRODUCT DESCRIPTION The Preset 10 Architectural Two is an enhanced version of our award winning Preset 10 Architectural controller The Preset 10 Architectural Two model PRE10A2 offers new features and different wiring options New features of the PRE10A2 include a master a merge mode DMX input merged with the Preset 10 output jumper selectable button modes radio or push on push off and a two gang design that fits all North American two gang electrical boxes The PRE10A2 has separate input and output ports which allows incoming levels to be merged with the local preset This merge capability allows multiple Preset 10s and or a live theatrical console to share control of the same devices Multi room control of a single dimmer rack is another possible use The Preset 10 Architectural Two control station is capable of storing up to ten presets These presets are recorded by capturing the output of aDMX512 console Each preset can be assigned a unique fade time from 0 to 999 seconds Presets are recalled by pressing one of ten PRESET buttons Systems consist of one or more stations and a power supply The solid aluminum faceplate is designed to install over a standard two gang electrical box Connections to the Pres
8. e red LED The LED will begin to flash To cancel the record operation press the RECORD button again 3 Press the PRESET button of the preset you wish to record The adjacent green LED will illuminate as you press the button A snapshot of the DMX512 signal is taken at the time the PRESET button is pressed Repeat steps 1 through 3 for each preset SETTING FADE TIMES Each preset can have its own fade time Upon recording a preset the fade time defaults to two seconds A preset s fade time is the time it will take that preset to fade in when selected To set a different fade time 1 Remove the DMX512 signal from the Preset 10 Architectural Two Required only if the Preset 10 is in switch over mode 2 Select the preset for which you wish to set the fade time 3 Using a small blunt object i e paper clip press the recessed TIME button next to the yellow LED The yellow time indicator and the green preset indicator will begin flashing You have ten seconds to set the fade time To cancel the operation press the TIME button again 4 Enter the three digit fade time in seconds using the PRESET buttons for the digit zero use the OFF button For example to enter 120 seconds press 1 2 OFF The operation is completed by a Entering a three digit time The operation will complete upon the entry of the third digit A one or two digit time may be entered with leading zeros five seconds entered as OFF OFF 5 b Entering a o
9. econds Preset 1 will then fade in using its recorded fade time When the fade is complete a fade from preset 1 to preset 2 will begin automatically using the fade time for preset 2 When that fade is complete a fade from preset 2 to preset 3 will begin using the fade time for preset 3 This auto following of presets will continue through preset 10 OFF and then wrap around to preset 1 again Auto follow mode is canceled by pressing any PRESET button Auto follow is only available in radio button mode JP6 installed To skip a preset in the auto follow progression set its fade time to 999 A fade time of zero will cause the auto following preset to pop on instantly This is useful if followed by a preset whose fade time is other than zero For example Recording presets 1 and 2 as red 3 and 4 as green and 5 and 6 as blue then setting the odd fade times to zero and the even fade times to two seconds would create an auto follow show of red bumping to green bumping to blue and bumping back to red with each color staying on for two seconds presets 7 10 fade times set to 999 Bump is a theatrical lighting term meaning to fade to in zero time PRESET 10 OFF SPECIAL FUNCTION If the levels stored in preset 10 OFF are all zeros a special function is enabled When preset 10 OFF is selected and the fade is complete the Preset 10 Architectural Two stops sending DMX By ending DMX transmission many moving lights and dimming systems will en
10. et 10 Architectural Two are power 2 wires and DMX512 3 wires Power for the Preset 10 can be supplied from a variety of sources including a 10V class 2 doorbell transformer The Preset 10 Architectural Two system can work in conjunction with a lighting console automatically switching between the Preset 10 and the console or by merging the console s levels with the Preset 10 s levels In this switch over mode when there is DMX512 present at the Preset 10 s input the Preset 10 goes off line and the console has control Upon loss of DMX from the console the Preset 10 takes control and either returns to its pervious preset or holds the last console look jumper selectable In merge mode the Preset 10 merges the levels from the console with the levels of the currently active preset PRESET BUTTON MASTER UP BUTTON PRESET LED GREEN MASTER DOWN BUTTON MASTER FULL LED YELLOW MASTER ZERO LED YELLOW RECESSED TIME BUTTON FADE LED YELLOW RECESSED RECORD BUTTON SIGNAL RECORD LED RED SPECIFICATIONS Connector Connector pin out Input Output Circuit Indicators User controls Option Jumpers Power input Color Size Phoenix Contact MSTB series 3 position plug in terminal block Model MSTB MSTB 2 5 3 ST 5 08 Order Number 17 57 02 2 Phoenix Contact MSTB series 5 position plug in terminal block Model MSTB 2 5 5 ST 5 08 Order Number 17 57 04 8 1 C DMX512 common 2 DMX512 data input
11. nces in half Systems with three Preset 10s on a single power supply should divide these distances by three Systems containing multiple Preset 10s may contain multiple power supplies Wire Gauge Supply Voltage 24 22 20 18 16 14 12 Resistance per foot 51mQ 35mQ 22mO 14mQ 9mO 6 4mQ 9VDC or 10VAC 90 140 225 350 550 900 1500 12VDC or 12VAC 360 460 900 1400 2200 3000 3000 15VDC or 16VAC 540 840 1350 2100 3000 3000 3000 18VDC 810 1260 2025 3000 3000 3000 3000 24VDC 1500 3000 3000 3000 3000 3000 3000 MAXIMUM POWER SUPPLY CABLE LENGTH The determining factor for wire length is voltage drop in the wire The Preset 10 must receive 9 volts 8 volts absolute minimum atits terminals for proper operation Using Ohms Law a skilled technician can calculate the voltage drop using the Preset 10s current draw of 0 2 Amps the resistance per foot shown below and the length of the wire Wire Gauge 24 22 20 18 16 14 12 Resistance per foot 51mQ 35 MQA 22mO 14mQ 9mO 6mQ 4mO POWER SUPPLY The voltage provided to the Preset 10 Architectural Two must be between 9 and 24 volts DC or 10 and 16 volts AC The Preset 10 Architectural Two has been designed to operate on a standard class 2 doorbell transformer For example Ace Hardware s model ACE36483 10 volt 5 watt transformer SAMPLE WIRING DIAGRAMS Single Master Note All jumpers installed 120VAC PRE10 AZ MASTER H e m H sm oie
12. ne or two digit time followed by pressing the TIME button C Entering a one or two digit time and waiting ten seconds for the operation to time out RECALLING PRESETS Preset are recalled by pressing one of the PRESET buttons The indicator next to the selected preset will illuminate and the fade to the new preset will begin Note that the lighting levels may not change quickly if the recorded fade time is long The yellow TIME indicator will illuminate during the fade In radio button mode JP6 installed pressing a PRESET button will cancel the current preset and fade to the selected preset In push on push off mode JP6 removed selecting a preset that was off will fade in the selected preset using a Highest Takes Precedence technique Deselecting a preset that was on will fade out the preset removing it from the output Preset 10 OFF is special in that when selected it cancels presets 1 through 9 just as it does in radio button mode Similarly selecting any preset other than preset 10 OFF cancels it AUTO FOLLOW Auto follow is typically used where a Preset 10 is dedicated to a specific task such as a continuously fading cove lighting or from one look to another in a night club A Preset 10 that loses power while in auto follow will resume auto follow when power is restored Auto follow is a mode in which each of the ten presets is recalled in order To begin auto follow press and hold PRESET 1 until all of the LEDs flash about 5 s
13. r White Blue Stripe Room 2 TB1 2 Dimmer Cabinet Data Equivalent Blue White Stripe TB1 3 Data UP STREAM SLAVE Note Master Remove JP4 120VAC Slave Remove JP2 amp JP4 PRE10 A2 SLAVE MASTER E E vm sH lt DIMMERS CABLE COLOR FROM TO USE 120 Ohm Data Cable Shield Pin 1 TB1 1 Common 1 Belden 9829 or White Blue Stripe 5 Pin XLR Plate Pin 2 TB1 2 Data Equivalent Blue White Stripe Pin 3 PRE10 A2 Slave TB1 3 Data 2 418 AWG Black Common TB1 4 Supply e Wires Red Pener Suply Power TB1 5 Supply hot 120 Ohm Data Cable Shield TB1 1 TB2 1 Common 3 Belden 9829 or White Blue Stripe TB1 2 TB2 2 Data Equivalent Blue White Stripe PRE10 A2 Slave TB1 3 PRE10 A2 Master TB2 3 Data 2 18 AWG Black TB1 4 TB1 4 Supply Stranded Wires Red TB1 5 TB1 5 Supply hot 120 Ohm Data Cable Shield TB1 1 2 5 Belden 9829 or White Blue Stripe PRE10 A2 Master TB1 2 Dimmer Cabinet Data Equivalent Blue White Stripe TB1 3 Data DOWN STREAM SLAVE Note Master Remove JP4 Slave Remove JP2 amp JP4 120VAC CABLE COLOR FROM PRE10 AZ MASTER TO DIMMERS USE 420 Ohm Data Cable Shield Pin 1 2 1 1 Belden 9829 or White Blue Stripe XLR Pin 2 TB2 2 Data 3 t Equivalent Blue White Stripe Pin 3 PRE10 A2 Master TB2 3 Data 2 2 18 AWG Black Power
14. ter their standby mode To defeat this feature and enable continuous transmission of DMX record a DMX level other than zero in preset 10 for example record DMX channel 512 at a level of 1 MASTER The MASTER up and down buttons allow proportional control of the current look When the master is at full 100 the yellow LED adjacent to the MASTER UP button is illuminated When the master is at zero 0 the yellow LED adjacent to the MASTER DOWN button is illuminated Pressing the MASTER UP or MASTER DOWN button increments or decrements the master level by 1 Holding the MASTER UP or MASTER DOWN button will fade the master level It takes 5 seconds to fade the master fully up or down The master only affects the levels of the Preset 10 not the levels from the console DMX512 input
Download Pdf Manuals
Related Search