Home

Primary

1. default setting The IRQ and address range for both ports are fixed However if you wish to disable the port or change these parameters later you can do this in the system BIOS setup The table below shows the settings for the PCM 4823 4823L board s ports Table 2 5 PCM 4825 4825L Serial port default settings Port Address Interrupt Default COM1 3F8 3E8 IRO4 3F8 COM2 2F8 2E8 IRQS 2F8 18 PCM 4823 4823L User s Manual 2 12 VGA interface connections The PCM 4823 4823L board s SVGA interface can drive conven tional CRT displays and is capable of driving a wide range of flat panel displays including electroluminescent EL gas plasma passive LCD and active LCD displays The card has two connec tors to support these displays one for standard CRT VGA monitors and one for flat panel displays 2 12 1 CRT display connector CN14 CN15 is a 15 pin D SUB connector commonly used for conven tional CRT displays Pin assignments for CRT display connector CN15 are detailed in Appendix A 2 12 2 Flat panel display connector CN6 CN6 consists of a 44 pin dual in line header The PCM 4823 4823L provides a bias control signal on CN6 which can be used to control the LCD bias voltage It is recom mended that the LCD bias voltage not be applied to the panel until the logic supply voltage 5 V and panel video signals are stable Under normal operation the control signal ENAVE
2. 47 5 5 5 Changing color schemes eee 47 3 3 6 DOS Setups OE EE ertet tree rr Ete oe 48 5 5 7 Changing display drivers in DOS oo 48 5 5 8 Panning drivers seen 49 5 5 9 Linear acceleration drivers oo 49 5 6 Windows 95 drivers setup procedure 50 5 7 Windows NT drivers setup procedure 50 SA SCP EER EIE EA ee rete 50 MUNI SEE 50 941 3 Step 2 OE EE Hae EH PER 51 5 8 OS 2 drivers setup procedure eese 51 5 8 1 Preliminary steps 51 5 8 2 Installing from diskette AAA 51 5 8 3 Selecting monitor type oooocoooooo 53 5 8 4 Selecting screen resolution refresh rate 53 5 8 5 Installation notes 54 Appendix A Pin Assignments 55 A 1 CRT display connector CN14 esses 56 A 2 Flat panel display connector CN6 56 A 3 COM2 RS 232 422 485 serial port CN9 57 AA Keyboard and mouse connnector CN13 57 A 5 Main power connector CN11 ooooo Wooo 58 A 6 IDE hard drive connector CN 58 A 7 COMI RS 232 serial port CN12 ese esse se ee ee 59 A 8 Ethernet connector CN10 oooo W 0 59 A 9 Peripheral power connector CN1 60 A 10 Floppy drive connector CN 60 A 11 Parallel p
3. PCM 4823 4823L 486 Based Single Board Computer with SVGA LCD and Ethernet Interface Copyright Notice This document is copyrighted 1997 All rights are reserved The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual is intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use nor for any infringements upon the rights of third parties which may result from its use Acknowledgements VIA is a trademark of VIA Technology Inc AMD is a trademark of Advanced Micro Devices Inc Award is a trademark of Award Software International Inc Cyrix is a trademark of Cyrix Corporation IBM PC AT PS 2 and VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corp SMC is a trademark of Standard Microsystems Corporation RTL is a trademark of Realtek Semi Conductor Co Ltd C amp T is a trademark of Chips and Technologies Inc UMC is a trademark of United Microelectronics Corporation All other product names or trademarks are properties of their respective owners
4. Evaluation Not For Sale Error Message Figure 3 2 BIOS VGA setup screen 24 PCM 4823 4823L User s Manual 3 At the prompt type in the BIN file which supports your display When you are sure that you have entered the file name correctly press lt Enter gt The screen will ask Do you want to save If you wish to continue press Y If you change your mind or have made a mistake press N 4 If you decide to continue the screen will issue a prompt which will then ask Are you sure to program Y N If you wish to continue press Y Press N to exit the program The new VGA configuration will then write to the ROM BIOS chip This configuration will remain the same until you run the AWDFLASH EXE program and change the settings 3 4 Connections for four standard LCDs 3 4 1 Connections to Sharp LM64183P 640 x 480 DSTN MONO LCD Table 3 1 Connections for Sharp LM64183P LCD LM64P83 PCM 4823 CN6 Pin Pin name Pin Pin name CN1 1 S 36 FLM CN1 2 CP1 38 LP CN1 3 CP2 35 SHFCLK CN1 4 DISP 5 5 V CN1 5 VDD 6 5 V CN1 6 VSS 3 GND CN1 7 VEE 17 V external power CN1 8 DUO 12 P3 CN1 9 DU1 11 P2 CN1 10 DU2 10 P1 CN1 11 DUS 9 PO CN1 12 DLO 16 P7 CN1 13 DL1 15 P6 CN1 14 DL2 14 P5 CN1 15 DL3 13 P4 Chapter 3 Software Configuration 25 3 4 2 Connections to PLANAR EL 640 x 480 AD4 EL Table 3 2 Connections for Planar EL PLANAR 640 x 480 AD4 PC
5. Shift F2 Color F Load BIOS Defaults F7 Load Setup Defaults Figure 4 3 BIOS features setup Chapter 4 Award BIOS Setup 35 4 2 4 CHIPSET features setup By choosing the CHIPSET FEATURES SETUP option from the INITIAL SETUP SCREEN menu the screen below is displayed This sample screen contains the manufacturer s default values for the PCM 4823 4823L ROM ISA BIOS ZCALG6AKE CHOS SETUP UTILITY CHIPSET FEATURES SETUP Auto Configuration Enabled Onhoard local bus IDE Enabled Decoupled Refresh Enabled IDE Primary Master PIO Auto Relocate 256k 384k Disabled IDE Primary Slave PIO Auto Video BIOS Cacheable Enabled Onboard FDD Controller Enabled System BIOS Cacheable Enabled Onboard Serial Port 1 COML 3FS CHRDY for IS Master Enabled Onboard Serial Port 2 COM2 2F8 Memory Hole At 15Mh Addr Disabled Onboard Parallel Port 5 378 TRQ DRAM Timing Control Fast Onboard Parallel Mode ECP EPP Fast DRAM Disabled ECP Mode Use DMA Ha Burat Urite Disabled IR Function UnUsed CPU Write Back Cache Disabled LAN Card Boot ROM Disable ESC Quit ti Select Item Fl Help PU PD c Modify FS Old Values Shift Fz Color F Load BIOS Defaults F7 Load Setup Defaults Figure 4 4 CHIPSET features setup 36 PCM 4823 4823L Users Manual 4 2 5 Power management setup By choosing the POWER MANAGEMENT SETUP option from the INITIAL SETUP SCREEN menu the sc
6. formed to select monitor type This section applies only after installation or when a different monitor is used 1 Open the OS 2 System folder 2 Open the System Setup folder 3 Open the System object 4 When the System Settings notebook appears select the Screen tab This will take you to page 2 of the settings 5 On Screen page 2 select your monitor type from the Display Name list If your monitor is not listed select DEFAULT Return to Screen page 1 It may be necessary to restart your system to have all refresh rate options available 5 8 4 Selecting screen resolution refresh rate To switch to a different video resolution color depth or refresh rate follow the steps below 1 Open the OS 2 System folder 2 Open the System Setup folder 3 Open the System object 4 From the selection windows provided select a new Screen Resolution and Screen refresh rate Please note Refresh rates other than 60 Hz are only valid when the display is switched to CRT only display mode 5 Close the System Settings notebook 6 Perform a shutdown and restart for the changes to take effect Chapter 5 SVGA Setup 53 5 8 5 Installation notes 1 During the installation of this driver DISPLAY LOG and DSPINSTL LOG files are created in OS2 INSTALL directory These files identify the OS 2 system files that were updated and indicate whether the installation was successful The DISPLAY LOG file also contains a string which i
7. to exit to DOS Step 3 Change to the directory where you installed Windows usually CAWINDOWS Step 4 Type SETUP lt ENTER gt to run the Windows Setup program It will show the current Windows configuration Use the up arrow key to move to the Display line and press lt ENTER gt A list of display drivers will be shown Use the arrow keys to select one of the drivers starting with an asterisk and press lt ENTER gt Step 5 Follow the directions on the screen to complete the setup In most cases you may press lt ENTER gt to accept the suggested option When Setup is done it will return to DOS Type WIN lt ENTER gt to start Windows with the new display driver 5 5 7 Changing display drivers in DOS To change display drivers from DOS change to the Windows directory and run Setup repeating steps 4 and 5 from the previous page Besides the special display drivers marked by an asterisk you should be able to use the following standard drivers VGA 640x480 16 colors Super VGA 800x600 16 colors 48 PCM 4823 4823L User s Manual 5 5 8 Panning drivers Special panning drivers are provided to allow high resolution modes to be displayed on a flat panel or CRT These drivers will show a section of a larger screen and will automatically pan or scroll the screen horizontally and vertically when the mouse reaches the edge of the display 5 5 9 Linear acceleration drivers A special high performance linear acceleration dri
8. 1 13 GND 14 DRIVE SELECT 0 15 GND 16 MOTOR 1 17 GND 18 DIRECTION 19 GND 20 STEP 21 GND 22 WRITE DATA 23 GND 24 WRITE GATE 25 GND 26 TRACK 0 27 GND 28 WRITE PROTECT 29 GND 30 READ DATA 31 GND 32 HEAD SELECT 33 GND 34 DISK CHANGE 60 PCM 4823 4823L User s Manual A 11 Parallel port connector CN4 Table A 11 PCM 4823 4823L parallel port connector Pin Signal 1 STROBE 2 AUTOFD 3 DO 4 ERR 5 D1 6 UNIT 7 D2 8 SLCTINI 9 D3 10 GND 11 D4 12 GND 13 D5 14 GND 15 D6 16 GND 17 D7 18 GND 19 ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT 26 N C Appendix A Pin Assignments 61 A 12 IR connector CN8 Table A 12 PCM 4823 4823L IR connector Pin Signal 5 V N C IR_RX GND OT BOD IR TX 62 PCM 4823 4823L User s Manual A 13 System l O ports System UO ports Addr range Hex Device 000 01F DMA controller 020 021 Interrupt controller 1 master 022 023 Chipset address 040 05F 8254 timer 060 06F 8042 keyboard Controller 070 07F Real time clock non maskable interrupt NMI mask 080 09F DMA page register 0A0 0BF Interrupt controller 2 OCO ODF DMA controller OFO Clear math co processor OF 1 Reset math co processor OFB OFF Math co processor 1FO 1F8 Fixed disk 200 207
9. D None OMB D n D D Q Drive 1 44M 3 5 in Drive B None Base Memory DE Video 1 EGA VGA Extended Memory DE Other Memory 512K Halt On All But Keyboard Total Memory 512K ESC Quit tie Select Item PU PD c Modify Fl Help Shift F2 Change Color Figure 4 2 CMOS setup screen 34 PCM 4823 4823L User s Manual 4 2 3 BIOS features setup By choosing the BIOS FEATURES SETUP option from the INITIAL SETUP SCREEN menu the screen below is displayed This sample screen contains the manufacturer s default values for the PCM 4823 4823L ROM ISA BIOS 2C4L6AKE BIOS FEATURES SETUP AWARD SOFTWARE INC Virus Warning Disabled Video BIOS Shadow Enabled CPU Internal Cache Enabled CEOOO CEFFF Shadow Disabled Quick Power On Self Test Enabled CCOOO CFFFF Shadow Disabled Boot Sequence PCA DOOOO DSFFF Shadow Disabled Swap Floppy Drive Disabled D4000 D7FFF Shadow Disabled Boot Up Floppy Seek Enabled DS000 DEFFF Shadow Disabled Boot Up NumLock Status On DCODO DFFFF Shadow Disabled Boot Up System Speed High IDE HDD Block Mode Enabled Gate 420 Option Fast Memory Parity Check Disabled Typematic Rate Setting Disabled Typematic Rate Chars Sec 6 Typematic Delay Msec 250 Security Option i Setup PS 2 mouse function control Enabled ESC Quit ti Select Item OS Select For DRAM gt 64MB Non 052 Fl Help PU PD c Modify F5 Old Values
10. E PC 104 module PCM 4825 4825L Figure B 1 PC 104 module mounting diagram 8 9 82 5 oo Sa coco t a m C 90 8 54 85 1 y 0 90 2 Figure B 2 PC 104 module dimensions mm 0 1 Appendix B Installing PC 104 Modules 69 Table B 1 PCA 4823 4823L PC 104 connectors CN3 CN5 Pin Signal CN3 Signal CN5 Number Row A Row B Row C Row D 0 0 V OV 1 IOCHCHK OV SBHE MEMCS16 2 SD7 RESETDRV LA23 10CS16 3 SD6 5V LA22 IRQ10 4 SD5 IRQ9 LA21 IRQ11 5 SD4 5V LA20 IRQ12 6 SD3 DRQ2 LA19 IRQ15 7 SD2 12V LA18 IRQ14 8 SD1 ENDXFR LA17 DACKO 9 SDO 12V MEMR DRQO 10 IOCHRDY N C MEMW DACK5 11 AEN SMEMW SD8 DRQ5 12 SA19 SMEMR SD9 DACK6 13 SA18 IOW SD10 DRQ6 14 SA17 IOR SD11 DACK7 15 SA16 DACK3 SD12 DRQ7 16 SA15 DRQ3 SD13 5V 17 SA14 DACK1 SD14 MASTER 18 SA13 DRQ1 SD15 OV 19 SA12 REFRESH KEY OV 20 SA11 SYSCLK 21 SA10 IRQ7 22 SA9 IRQ6 23 SA8 IRQ5 24 SA7 IRQ4 25 SA6 IRQ3 26 SA5 DACK2 x 27 SA4 TC 28 SA3 BALE E 29 SA2 5V 30 SA1 OSC 31 SAO OV 32 OV 0 V active low 70 PCM 4823 4823L User s Manual APPENDIX DOC 2000 Installation Guide This appendix contains information on the DiskOnChip 2000 quick installation guide Itincludes DiskOnC
11. Game VO 278 27F Parallel printer port 2 LPT 3 2F8 2FF Serial port 2 300 31F Prototype card 360 36F Reserved 378 37F Parallel printer port 1 LPT 2 380 38F SDLC bisynchronous 2 3A0 3AF Bisynchronous 1 3B0 3BF Monochrome display and printer adapter LPT1 3C0 3CF Reserved 3D0 3DF Color graphics monitor adapter 3F0 3F7 Diskette controller 3F8 3FF Serial port 1 PNP audio I O map range from 220 250H 16 bytes MPU 401 select from 300 330H 2 bytes Appendix A Pin Assignments 63 A 14 DMA channel assignments DMA channel assignments Channel Function Available Available Floppy disk 8 bit transfer Available Cascade for DMA controller 1 Available Available NOU BIO DO Available Audio DMA select 0 1 or 3 A 15 Interrupt assignments Interrupt assignments Priority Interruptz Interrupt source 1 NMI Parity error detected 2 IRQ 0 Interval timer 3 IRQ 1 Keyboard IRQ 2 Interrupt from controller 2 cascade 4 IRQ 8 Real time clock 5 IRQ 9 Cascaded to INT OA IRQ 2 6 IRQ 10 Available 7 IRQ 11 Available 8 IRQ 12 PS 2 mouse 9 IRQ 13 INT from co processor 10 IRQ 14 Fixed disk controller 11 IRQ 15 Available 12 IRQ 3 Serial communication port 2 13 IRQ 4 Serial communication port 1 14 IRQ 5 Parallel port 15 IRQ 6 Diskette controller FDC 16 IRQ 7 Parallel port 1 print port 64 PCM 48
12. ROM is installed the RSETS019 EXE program does not support PNP mode configuration To execute the configuration to view the current configuration or to run diagnostics do the following 1 Power the PCM 4823 4823L on Ensure that the RSET8019 EXE file is located in the working directory 2 At the prompt type RSET8019 exe and press Enter The Ethernet configuration program will then be displayed Chapter 3 Software Configuration 29 3 A simple screen displays the available options for the Ethernet interface Highlight the option which you wish to change using the Up and Down keys To change a selected item press lt Enter gt and a window will appear with the available options Highlight your selection and press lt Enter gt Each highlighted option has a helpful message guide displayed at the bottom of the screen for additional information 4 After you have made your selections and you are sure that this 1s the configuration you want press lt ESC gt A prompt will appear asking if you want to save the configuration Press Y if you want to save The Ethernet Setup Menu also offers three very useful diagnostic functions These are 1 Run EEPROM test 2 Run Diagnostics on Board 3 Run Diagnostics on Network Each option has its own display screen which shows the format and result of any diagnostic tests undertaken 30 PCM 4823 4823L User s Manual CHAPTER Award BIOS Setup This chapter describes how to
13. RS 232 422 485 with DB 9 connector as COMI and a mini DIN PS 2 keyboard mouse interface A local bus SVGA LCD display controller LCD EL and CRT displays allows LCD screen resolutions up to 1024 x 768 and CRT resolutions up to 1280 x 1024 16 colors PCM 4823 only The PCM 4823 4823L complies with the Green Function standard and supports three types of power saving features Normal Doze and Sleep modes The display type configuration is done through software A single Flash chip holds the system BIOS and the VGA BIOS This minimizes the number of chips and eases configuration You can change the display BIOS simply by programming the Flash chip If you need any additional functions the PCM 4823 4823L has a PC 104 connector for future upgrades 2 PCM 4823 4823L User s Manual 1 2 Features Ultra compact size single board computer as small as a 3 1 2 hard disk drive 145 mm x 102 mm On board AMD DX5 133 5x86 133 CPU Up to 32 MB on board EDO Fast Page mode DRAM Local bus SVGA display controller LCD EL and CRT displays flat panel type configured by programming the Flash chip PCM 4823 On board 16 bit Ethernet interface Supports M Systems DiskOnChip 2000 Flash memory Built in VL Bus Enhanced IDE AT bus hard disk drive interface On board mini DIN PS 2 keyboard mouse connector Two serial ports one RS 232 one RS 232 422 485 or infared selectable uses 16C550 UARTs with 16 byte FIFO Upgradeable through P
14. 23 4823L User s Manual A 16 1st MB memory map 1st MB memory map Addr range Hex Device FOOOh FFFFh System ROM C800h EFFFh Unused C000h C7FFh Expansion ROM B800h BFFFh CGA EGA VGA text BOOOh B7FFh Unused A000h AFFFh EGA VGA graphics 0000h 9FFFh Base memory D000 D400H DOC 2000 Appendix A Pin Assignments 65 66 PCM 4823 4823L User s Manual APPENDIX Installing PC 104 Modules This appendix gives instructions for installing PC 104 modules B 1 Installing PC 104 modules The PCM 4823 4823L s PC 104 connectors give you the flexibility to attach PC 104 modules Installing these modules on the PCM 4823 4823L is quick and simple The following steps show how to mount the PC 104 modules 1 Remove the PCM 4823 4823L from your system paying particu lar attention to the safety instructions already mentioned above Make any jumper or link changes required to the CPU card now Once the PC 104 module is mounted you may have difficulty in accessing these Normal PC 104 modules have male connectors and mount directly onto the main card Refer to the diagram on the following page Mount the PC 104 module onto the CPU card by pressing the module firmly but carefully onto the mounting connectors Secure the PC 104 module onto the CPU card using the four mounting spacers and screws 68 PCM 4823 4823L User s Manual o E PC 104 Mounting Support Female Male
15. 6 colors 1 3 3 Ethernet interface Chipset RTL 8019AS VO address switchless setting Software compatible with NE1000 and NE2000 Built in boot ROM 1 3 4 Mechanical and environmental Dimension 5 9 L x 4 2 W 145 mm x 102 mm Power supply voltage 5 V 4 75 V to 5 25 V Max power requirements 5 V 2 A typical Operating temperature 32 F to 140 F 0 C to 60 C Weight 0 65 kg weight of total package Chapter 1 General Information 5 6 1 4 Board layout and dimensions ZER E p Cu LL Am486DX2 66 Am486DX4 100 Am486DX5 133 ui Bee VT82C4966 Pin RR TH cu ni Pini E 2 ae wu Zam l int um 6 Wm es Pin e HH Maan 6 Aen e ULI o Hl K 2 NIET E 95 25 213 17 102 Figure 1 1 PCM 4823 4823L dimensions PCM 4823 4823L User s Manual CHAPTER Installation This chapter tells how to set up the PCM 4823 4823L hardware including instructions on setting jumpers and connecting peripherals switches and indicators Be sure to read all the safety precautions before you begin the installa tion procedure 2 1 Jumpers and connectors Connectors on the board link it to external devices such as hard disk drives a keyboard or expansion bus connectors In additi
16. 823 4823L IDE hard drive connector Pin Signal Pin Signal 1 IDE RESET 2 GND 3 DATA 7 4 DATA 8 5 DATA 6 6 DATA 9 7 DATA 5 8 DATA 10 9 DATA 4 10 DATA 11 11 DATA 3 12 DATA 12 13 DATA 2 14 DATA 13 15 DATA 1 16 DATA 14 17 DATA 0 18 DATA 15 19 SIGNAL GND 20 N C 21 N C 22 GND 23 IO WRITE 24 GND 25 IO READ 26 GND 27 IO CHANNEL READY 28 N C 29 N C 30 GND 31 IRQ14 32 10CS16 33 ADDR 1 34 N C 35 ADDR O 36 ADDR 2 37 HARD DISK SELECTO 38 HARD DISK SELECT 1 39 IDE ACTIVE 40 GND 41 VCC 42 VCC 43 GND 44 N C 58 PCM 4823 4823L User s Manual A 7 COM1 RS 232 serial port CN12 Table A 7 PCM 4823 4823L COM1 RS 232 serial port Pin Signal DCD RxD TxD DTR GND DSR RTS CTS R OO NOU ADO ND A 8 Ethernet 10Base T connector CN10 Table A 8 PCM 4823 4823L Ethernet 10Base T connector Signal XMT XMT RCV N C N C RCV N C N C Y 5 OO On BR PD Appendix A Pin Assignments 59 A 9 Peripheral power connector CN1 Table A 9 PCM 4823 4823L peripheral power connector Pin PM 0 A 10 Floppy drive connector CN2 Table A 10 PCM 4823 4823L floppy drive connector Pin Signal Pin Signal 1 GND 2 DENSITY SELECT 3 GND 4 N C 5 GND 6 N C 7 GND 8 INDEX 9 GND 10 MOTOR 0 11 GND 12 DRIVE SELECT
17. Both CRT and panel displays can be used simultaneously The PCM 4823 4823L can be set in one of three configurations on a CRT on a flat panel display or on both simultaneously The system is initially set to simultaneous display mode In the utility diskette there are three COM files which can be used to select the display Simply type the filename at the DOS prompt CT COM Enables CRT display only FP COM Enables panel display only SM COM Enables both displays at the same time 5 4 Sleep mode The utility diskette contains two files that support sleep mode Simply type the filename at the DOS prompt ON COM switches to normal display mode OFF COM switches to sleep mode Chapter 5 SVGA Setup 45 5 5 Driver installation Windows 3 1 amp DOS 5 5 1 Necessary prerequisites The instructions in this manual assume that you understand elementary concepts of MS DOS and the IBM Personal Computer Before you attempt to install any driver or utility you should know how to copy files from a floppy disk to a directory on the hard disk understand the MS DOS directory structure and know how to format a floppy disk If you are uncertain about any of these concepts please refer to the DOS or Windows user reference guides for more information before you proceed with the installa tion 5 5 2 Before you begin Before you begin installing software drivers you should make a backup copy of the display driver diskette and store the origin
18. C 104 module Green engine with sleep mode and low power consumption Single 5 V power supply Chapter 1 General Information 3 1 3 Specifications 1 3 1 Standard SBC functions CPU Embedded AMD DX5 133 5x86 133 processor BIOS AWARD 128 KB Flash memory Chipset VIA VT82C496G System memory One 72 pin SIMM sockets accepts 1 MB 2 MB 4 MB 8 MB 16 MB and 32 MB Supports FPM or EDO DRAM from 1 MB to 32 MB Enhanced IDE hard disk drive interface Supports up to two IDE VL bus hard disks BIOS auto detect and PIO Mode 3 transfer protocol Serial ports One serial RS 232 port one serial RS 232 422 485 port Two 16550 serial UARTS Parallel port One parallel port supports SPP EPP ECP mode Infrared port Shared with COM2 Transfer rate up to 115 kbps Keyboard mouse connector Mini DIN connector supports standard PC AT keyboard and a PS 2 mouse Power management Supports power saving modes including Normal Doze Sleep modes APM 1 1 compliant Supports M Systems DiskOnChip 2000 Flash disk up to 72 MB 4 PCM 4823 4823L User s Manual 1 3 2 Local bus flat panel VGA interface PCM 4823 Chipset C amp T 65550 Display memory 1 MB DRAM Display type Supports CRT and flat panel EL LCD and gas plasma flat panel displays Can display CRT and flat panel simultaneously Flat panel display mode Panel resolution supports up to 1024 x 768 CRT display mode Non interlaced CRT monitors resolutions up to 1280 x 1024 1
19. D AUTO DETECTION utility can automatically detect the IDE hard disk installed in your system You can use it to self detect and or correct the hard disk type configuration ROM ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC HARD DISK TYPE SIZE CYLS HEADS PRECOMP LANDZ SECTORS MODE Primary master MB 790 15 65535 789 57 Select Secondary Slave Option N Skip N ESC SKIP Figure 4 8 IDE HDD auto detection screen 4 2 11 Save amp exit setup If you select this option and press lt Enter gt the values entered in the setup utilities will be recorded in the chipsets CMOS memory The microprocessor will check this every time you turn your system on and compare this to what it finds as it checks the system This record is required for the system to operate 4 2 12 Exit without saving Selecting this option and pressing lt Enter gt lets you exit the Setup program without recording any new values or changing old ones 42 PCM 4823 4823L User s Manual CHAPTER SVGA Setup The PCM 4823 4823L features an on board flat panel VGA interface This chapter provides instructions for installing and operating the software drivers on the included display driver diskette 5 1 Before you begin To facilitate the installation of the enhanced display device drivers and utility software you should read the instructions in this chapter carefully The enhanced display drivers for th
20. E is active high When the PCM 4823 4823L board s power is applied the control signal is low until just after the relevant flat panel signals are present Configuration of the LCD type is done completely via the software utility You do not have to set any jumpers Refer to Chapter 3 for software setup details Refer to Chapter 3 for details on connecting the four standard LCD s Sharp LM64183P Toshiba LTM10C042 Sharp 64C142 and Planar EL Display Chapter 2 Installation 19 2 13 Ethernet interface connections The PCM 4823 4823L is equipped with a high performance 16 bit Ethernet interface which is fully compliant with IEEE 802 3 10 Mbps CSMA CD standards It is supported by all major network operating systems and is 100 Novell NE 2000 compati ble 2 13 1 10Base T RJ 45 connector CN10 10Base T connections are made via the on board RJ 45 connector 20 PCM 4823 4823L User s Manual CHAPTER Software Configuration This chapter details the software configu ration information It shows you how to configure the card to match your applica tion requirements Award system BIOS is covered in Chapter 4 Sections include LCD display configuration Connections for four standard LCDs 3 1 Introduction The PCM 4823 4823L system BIOS and custom drivers are located in a 128 KB 32 pin Flash ROM device designated U2 A single Flash chip holds the system BIOS and VGA BIOS The display type can be configured via
21. M 4823 CN6 Pin Pin name Pin Pin name 1 GND 3 GND 2 DO 21 P12 3 GND 3 GND 4 D1 22 P13 5 GND 3 GND 6 D2 23 P14 7 NC 8 D3 24 P15 9 NC 10 D4 17 P8 11 NC 12 D5 18 P9 13 NC 14 D6 19 P10 15 GND 4 GND 16 D7 20 P11 17 GND 4 GND 18 VCLK 42 ASHFCLK 19 GND 4 GND 20 BLANK 21 GND 8 GND 22 HS 37 M 23 NC 24 VS 36 FLM 25 NC 26 SELFTST 39 GND 27 COLMAP 39 GND 28 ENABLE 29 RESERVED 30 LOWPOW 31 32 NC 33 RESERVED 34 NC 26 PCM 4823 4823L User s Manual 3 4 3 Connections to Toshiba LTM10C042 640 x 480 TFT Color LCD Table 3 3 Connections for Toshiba LTM10C042 LTM10C042 PCM 4823 CN6 Pin Pin name Pin Pin name 1 GND 3 GND 2 CLK 35 SHFCLK 3 GND 4 GND 4 RO 27 P18 5 R1 28 P19 6 R2 29 P20 7 GND 8 GND 8 R3 30 P21 9 R4 31 P22 10 R5 32 P23 11 GND 33 GND 12 GO 19 P10 13 G1 20 P11 14 G2 21 P12 15 GND 33 GND 16 G3 22 P13 17 G4 23 P14 18 G5 24 P15 19 GND 34 GND 20 ENAB 37 M 21 GND 34 GND 22 BO 11 P2 23 B1 12 P3 24 B2 13 P4 25 GND 39 GND 26 B3 14 P5 27 B4 15 P6 28 B5 16 P7 29 GND 39 GND 30 VDD 5 5 V 31 VDD 6 5 V Chapter 3 Software Configuration 27 3 4 4 Connections to Sharp LM64C142 640 x 480 DSTN Color LCD Table 3 4 Con
22. OS 2C4L6AKEI CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE amp EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS Esc Quit tlae Select Item Fl Save amp Exit Setup Shift F2 Change Color Figure 4 1 BIOS setup program initial screen Award s BIOS ROM has a built in setup program that allows users to modify the basic system configuration This type of information is stored in battery backed CMOS RAM so that it retains the setup information when the power is turned off 4 2 1 Entering setup Poweron the computer and press Del immediately This will allow you to enter Setup Chapter 4 Award BIOS Setup 33 4 2 2 Standard CMOS setup When you choose the STANDARD CMOS SETUP option from the INITIAL SETUP SCREEN menu the screen shown below is displayed This standard setup menu allows users to configure system components such as date time hard disk drive floppy drive display and memory Once a field is highlighted on line help information is displayed in the bottom left of the menu screen ROM ISA BIOS ZCALSAEK STANDARD CMOS SETUP AWARD SOFTWARE INC Date mm dd yy Wed Noy 19 1997 Time hh imm ss 18 25 9 CYLS HEADS PRECOMP LANDZONE SECTORS MODE Drive C Auto OMb 0 0 0 AUTO Drive
23. Part No 2006482300 1st Edition Printed in Tarwan March 1998 Packing list Before you begin installing your card please make sure that the following materials have been shipped PCM 4823 4823L All in One Single Board Computer utility disk with system BIOS VGA BIOS utility programs 3 SVGA driver disks PCM 4823 only Ethernet driver disk 1 3 5 IDEflatcable 1 keyboard mouse cable secondary serial port cable RS 232 422 485 1 parallel cable floppy cable If any of these items are missing or damaged contact your distribu tor or sales representative immediately Contents Chapter 1 General Information 1 1 1 Introduction RE EE nanas 2 A OO 3 1 3 WE 4 1 3 1 Standard SBC functions sees 4 1 3 2 Local bus flat panel VGA interface PCM 4823 only 5 1 33 Ethernet interface ben ea e ehe ee aa 5 1 3 4 Mechanical and environmental ooo 5 1 4 Board layout and dimensions 6 Chapter 2 Installatioriz ss SE NS Ke ai 7 2 1 Jumpers and connectors ooooooocoo ooooooooooooooo 8 2 2 Locating jumpers ooooooo oo ooocooooooooooooooooooo 10 2 3 Locating connectoOrs oocoocooooooooo oooooooo 11 2 4 Setting jumpers ooooooooo ooocoooooooooooooooooooooooooooo 12 2 4 1 PCM 4823 Jumper Settings o 13 2 5 Safety precautions ooooooooooo ooooooooooooooooooo 14 2 6 Installing DRAM SIMMS ceooooooooo
24. YNC 7 GND 15 N C 8 GND A 2 Flat panel display connector CN6 Table A 2 PCM 4823 4823L flat panel display connector Pin Function Pin Function 1 12 V 2 12 V 3 GND 4 GND 5 Vcc 6 Vcc 7 ENAVEE 8 GND 9 PO 10 P1 11 P2 12 P3 13 P4 14 P5 15 P6 16 P7 17 P8 18 P9 19 P10 20 P11 21 P12 22 P13 23 P14 24 P15 25 P16 26 P17 27 P18 28 P19 29 P20 30 P21 31 P22 32 P23 33 GND 34 GND 35 SHFCLK 36 FLM 37 M 38 LP 39 GND 40 ENABKL 41 GND 42 ASHFCLK 43 ENAVDD 44 Vcc 56 PCM 4823 4823L User s Manual A 3 COM2 RS 232 422 485 serial port CN9 Table A 3 PCM 4823 4823L COM2 RS 232 422 485 series port Pin RS 232 port RS 422 port RS 485 port 1 DCD N C N C 2 DSR N C N C 3 RxD N C N C 4 RTS N C N C 5 TxD N C N C 6 CTS N C N C 7 DTR N C N C 8 RI N C N C 9 GND N C N C 10 N C N C N C 11 N C TxD DATA 12 N C TxD DATA 13 N C RxD N C 14 N C RxD N C A 4 Keyboard and mouse connnector CN13 Table A 4 PCM 4823 4823L keyboard and mouse connector Pin Signal KB DATA MS DATA GND Voc KB CLOCK OO BR Po MS CLOCK Appendix A Pin Assignments 57 A 5 Main power connector CN11 Table A 5 PCM 4823 4823L main power connector Pin Signal 1 12 V 2 GND 3 GND 4 5 V A 6 IDE hard drive connector CN7 Table A 6 PCM 4
25. al in a safe place The display driver diskette contains drivers for several versions of certain applications You must install the correct version in order for the driver to work properly so make sure you know which version of the application you have 5 5 3 Windows setup These drivers are designed to work with Microsoft Windows 3 1 You may install these drivers through Windows or in DOS Step 1 Install Windows as you normally would for a VGA display Run Windows to make sure that it is working correctly Step 2 Place the display driver diskette in drive A In Windows Program Manager choose File from the Options Menu Then from the pull down menu choose Run At the command line prompt type A SETUP Press the lt ENTER gt key or click OK to begin the installation At this point the setup program locates the directory where Windows is installed For proper operation the drivers must be installed in the Windows subdirectory Press lt ENTER gt to complete the installation Once completed the 46 PCM 4823 4823L User s Manual Display Driver Control Panel appears on the screen This Control Panel allows you to select and load the installed drivers Another method of installing these drivers is through the File Manager Click on Drive A Then double click on SETUP EXE to begin installation 5 5 4 Changing display drivers in Windows To change display drivers in Windows select the Windows Setup icon from the Main window You
26. charges Use a grounding wrist strap at all times Place all electronic components on a static dissipative surface or in a static shielded bag when they are not in the chassis 14 PCM 4823 4823L User s Manual 2 6 Installing DRAM SIMMs You can install anywhere from 1 MB to 32 MB of on board DRAM memory using 1 2 4 8 16 or 32 MB 72 pin SIMMs Single In Line Memory Modules DRAM access time lt 60 ns 2 6 1 Installing SIMMs NOTE The modules can only fit into a socket one way and their gold pins must point down into the SIMM socket The procedure for installing SIMMs appears below Please follow these steps carefully 1 2 Ensure that all power supplies to the system are switched Off Install the SIMM card Install the SIMM so that its gold pins point down into the SIMM socket Slip the SIMM into the socket at a 45 degree angle and carefully fit the bottom of the card against the connectors Gently push the SIMM into a perpendicular position until the clips on the ends of the SIMM sockets snap into place Check to ensure that the SIMM is correctly seated and all connector contacts touch The SIMM should not move around in its socket Chapter 2 Installation 15 2 7 IDE hard drive connector CN7 The built in Enhanced IDE Integrated Device Electronics controller supports up to two IDE devices including CD ROM drives tape backup drives a large hard disk drive and other IDE devices It also supports fast
27. ctors EDO FPM DRAM SIMM Power 5 12 V Socket CN1 Floppy Disk e U Ve RRE mr Am486DX2 66 Pin ma Parallel Port CN4 VT82C496G ou E Pint N GT EE LLL DE Hora TR c Disk CN7 PC 104 CN5 E E z Flat Panel Palos ne EYE Display CN6 CN3 mum umm 7 SE E i a LE Power 5 Ge III IL ni Vun 12 V pe CN11 m COM1 COM2 Ethernet Keyboard CRT Power CN12 CN9 CN10 PS 2 Mouse Display HDD LED CN13 oa NET IR Reset SW LED CN8 J5 Figure 2 2 PCM 4823 4823L connectors Chapter 2 Installation 11 2 4 Setting jumpers You may configure your card to match the needs of your applica tion by setting jumpers jumper is the simplest kind of electrical switch It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the clip To open a jumper you remove the clip Sometimes a jumper will have three pins labeled 1 2 and 3 In this case you would connect either pins 1 and 2 or 2 and 3 da 22 2s BS Open Closed Closed 2 3 The jumper settings are schematically depicted in this manual as follows i8 OO m O ee Open Closed Closed 2 3 A pair of needle nose pliers may be helpful when worki
28. dentifies the version of driver that was installed This information may be important when reporting an installation problem 2 During installation DSPINSTL will invoke the SVGA Configu ration program SVGA EXE to determine the hardware configu ration and create the file OS2 INSTALL S VGADATA PMI If this file is not created the adapter will not be supported When this step is done the display will be blanked and you may see a series of flashes on the display and what appears to be a cor rupted display This is normal as the configuration process is doing Video BIOS mode sets to determine which screen resolu tions BIOS supports This configuration information is then used to provide the System Settings Resolution and Refresh selec tions 54 PCM 4823 4823L User s Manual APPENDIX Pin Assignments This appendix contains information of a detailed or specialized nature It includes CRT display connector Flat panel display connector Main power connector RS 232 422 485 serial port connector Keyboard and mouse connector Peripheral power connector DE connector RS 232 serial port connector Ethernet RJ 45 connector Floppy connector Parallel connector R connector A 1 CRT display connector CN14 Tabler A 1 PCM 4823 4823L CRT display connector Pin Signal Pin Signal 1 RED 9 N C 2 GREEN 10 GND 3 BLUE 11 N C 4 N C 12 N C 5 GND 13 H SYNC 6 GND 14 V S
29. e PCM 4823 4823L board are located on the software installation diskette You must install the drivers and utility software by using the supplied SETUP program for DOS drivers Note The files on the software installation diskette are compressed Do not attempt to install the drivers by copying the files manually You must use the supplied SETUP program to install the drivers Before you begin it is important to note that most display drivers need to have the relevant software application already installed in the system prior to installing the enhanced display drivers In addition many of the installation procedures assume that you are familiar with both the relevant software applications and operating system commands Review the relevant operating system com mands and the pertinent sections of your application software s user s manual before performing the installation 44 PCM 4823 4823L User s Manual 5 2 Installation Disk 1 Windows 3 1 driver Disk 2 Windows 95 Windows NT drivers Disk 3 OS 2 drivers 5 3 Simultaneous display mode The 65550 VGA BIOS supports monochrome LCD EL color TFT and STN LCD flat panel displays It also supports interlaced and non interlaced analog monitors VGA color and VGA mono chrome in high resolution modes while maintaining complete IBM VGA compatibility Digital monitors i e MDA CGA and EGA are NOT supported Multiple frequency multi sync monitors are supported as analog monitors
30. er data transfer rates and allows the IDE hard disk drive to exceed 528 MB 2 7 1 Connecting the hard drive Connecting drives is done in a daisy chain fashion and requires one of two cables depending on the drive size 1 8 and 2 5 drives need a 1 x 44 pin to 2 x 44 pin flat cable connector 3 5 drives use a 1 x 44 pin to 2 x 40 pin connector Wire number 1 on the cable is red or blue and the other wires are gray 1 Connect one end of the cable to CN7 Make sure that the red or blue wire corresponds to pin 1 on the connector which is labeled on the board on the right side 2 Plug the other end of the cable to the Enhanced IDE hard drive with pin 1 on the cable corresponding to pin 1 on the hard drive See your hard drive s documentation for the location of the connector Connect a second drive as described above Unlike floppy drives IDE hard drives can connect to either end of the cable If you install two drives you will need to set one as the master and one as the slave by using jumpers on the drives If you install just one drive set it as the master 16 PCM 4823 4823L User s Manual 2 8 Keyboard and PS 2 mouse connector CN13 The PCM 4823 4823L board provides a mini DIN keyboard connector which supports both a keyboard and a PS 2 style mouse In most cases especially in embedded applications a keyboard is not used The standard PC AT BIOS will report an error or fail during power on self test POST a
31. er defined you can change the password stored in the CMOS The password can be at most 8 characters long Remember to enable this feature you must first select either Setup or System in the BIOS FEATURES SETUP 40 PCM 4823 4823L User s Manual 4 2 9 Security option Access to the BIOS setup can be controlled using a password A password will control access to the BIOS setup according to two differing options System password The system will not boot and access to Setup will be denied unless the correct password is entered at the prompt Setup password The system will boot but access to Setup will be denied unless the correct password is entered at the prompt To disable security first enter the BIOS setup and select the PASSWORD SETTING option in the main menu When prompted to enter a password press the lt ENTER gt key without entering a password then save the new settings This will will disable security Now when you boot you will not be prompted for a password you will enter setup directly If you lose or forget your password the following steps restore default settings 1 Power off the system 2 Set jumper J4 connecting pins 1 2 for at least 3 seconds to clear CMOS entries 3 Set jumper J4 connecting pins 2 3 4 Power on the system 5 Press the Del key to access CMOS settings Modify the settings as desired save and exit Chapter 4 Award BIOS Setup 41 4 2 10 Auto detect hard disk The IDE HD
32. fter a reset 1f the keyboard is not present The PCM 4823 4823L board s BIOS standard setup menu allows you to select All But Keyboard under the Halt On selection This allows no keyboard operation in embedded system applications without the system halting under POST power on self test 2 9 Power connector CN11 2 9 1 Main power connector 5V 12V CN12 Supplies main power to the PCM 4823 4823L 5 V and devices that require 12 V 2 10 IR connector CN8 This connector supports the optional wireless infrared transmitting and receiving module This module mounts on the system case You must configure the setting through BIOS setup Chapter 2 Installation 17 2 11 Serial ports CN12 CN9 The PCM 4823 4823L offers two serial ports one RS 232 and one RS 232 422 485 These ports let you connect to serial devices a mouse printers etc or a communication network 2 11 1 COM1 RS 232 port CN12 The serial port connectors are mounted on the bottom edge of the card The 9 pin D SUB connector to the left of the card is the RS 232 port 2 11 2 COM2 RS 232 422 485 selection CN9 The secondary port located above COMI consists of a 14 pin dual in line male header and can be configured to operate in RS 232 RS 422 or RS 485 mode This is done via J7 Table 2 4 COM2 selection J7 RS 232 RS 422 RS 485 5 35 1 S 32 1 5 Dk J7 Soll E gee OO ol lo OO 6 4 2 6 4 2 6 4 2
33. hip 2000 installation instruc tions Additional information and assistance C 1 DiskOnChip 2000 quick installation guide C 1 1 DiskOnChip 2000 installation instructions 1 Make sure the target platform is powered OFF 2 Plug the DiskOnChip 2000 device into its socket Verify the direction is correct pin 1 of the DiskOnChip 2000 is aligned with pin 1 of the socket 3 Power up the system 4 During power up you may observe the messages displayed by the DiskOnChip 2000 when its drivers are automatically loaded into the system s memory 5 At this stage the DiskOnChip 2000 can be accessed as any disk in the system 6 If the DiskOnChip 2000 is the only disk in the system it will appear as the first disk drive C in DOS 7 If there are more disks besides the DiskOnChip 2000 the DiskOnChip 2000 will appear by default as the last drive unless it was programmed as the first drive Please refer to the DiskOnChip 2000 utilities user manual 8 If you want the DiskOnChip 2000 to be bootable a Copy the operating system files into the DiskOnChip by using the standard DOS command for example sys d b The DiskOnChip should be the only disk in the systems or would be configured as the first disk in the system c using the DUPDATE utility DUPDATE D S DOC104 EXB FIRST set as c DUPDATE C S DOC104 EXB set as d 72 PCM 4823 4823L User s Manual C 1 2 Additional info
34. nections for Sharp LM64C142 LM64C142 PCM 4823 CN6 Pin Pin name Pin Pin name CN1 1 YD 36 FLM CN1 2 LP 38 LP CN1 3 XCX 35 SHFCLK CN1 4 DISP 5 5 V CN1 5 VDD 6 5 V CN1 6 VSS 3 GND CN1 7 VEE 27 V external power CN1 8 DUO 20 P11 CN1 9 DU1 19 P10 CN1 10 DU2 18 P9 CN1 11 DUS 17 P8 CN1 12 DU4 12 P3 CN1 13 DUS 11 P2 CN1 14 DU6 10 P1 CN1 15 DU7 9 PO CN2 1 VSS 4 GND CN2 2 DLO 24 P15 CN2 3 DL1 23 P14 CN2 4 DL2 22 P13 CN2 5 DL3 21 P12 CN2 6 DL4 16 P7 CN2 7 DL5 15 P6 CN2 8 DL6 14 P5 CN2 9 DL7 13 P4 CN2 10 VSS 8 GND 28 PCM 4823 4823L User s Manual 3 5 Ethernet Interface Configuration The PCM 4823 4823L s on board Ethernet interface supports all major network operating systems I O adress and interrupts are easily configured via the RSET8019 EXE program included on the utility disk The RSET8019 EXE program provides two ways to configure the Ethernet interface Configuration can be done automatically when you choose PNP plug and play When you choose jumperless configuration the following IRQ and I O address settings are available PCM 4823 4823L Ethernet Settings IRQ option I O address range Jumperless 2 5 10 200 300EFH Configuration 11 15 Default Settings IRQ 5 Address 300H Note 1 You can select an IRQ from the Options shown above but be certain that your selection does not conflict with other 1 0 devices 2 When Boot
35. ng with jumpers If you have any doubts about the best hardware configuration for your application contact your local distributor or sales representa tive before you make any changes Generally you simply need a standard cable to make most connec tions 12 PCM 4823 4823L User s Manual 2 4 1 PCM 4823 4823L Jumper Settings ood 321 J2 DOC2000 Address Setting Pins Address 1 2 3 4 5 6 close close close C800 C9FF close close open CC00 CDFF close open close D000 D1FF close open open D400 D5FF open close close D800 D9FF open close open DCOO DDFF open open close E000 E1FF open open open OFF J3 LCD Power Closed Voltage J4 Clear CMOS Pins 158 3 3 V Closed eeh J6 COM2 Selector a Pins VY AIME LOR 2 3 SV 1 2 Clear CMOS ed Result 2 3 3 6 V Battery Sr Ba kan On 1 2 RS232 3 4 RS 422 5 6 RS 485 5 31 sem ooo 642 default setting Figure 2 3 PCM 4823 4823L Jumper Settings Chapter 2 Installation 13 2 5 Safety precautions Warning Always completely disconnect the power cord from your board whenever you are working on it Do not make connections while the power is on because sensitive electronic components can be damaged by the sudden rush of power Caution Always ground yourself to remove any static charge before touching the board Modern electronic devices are very sensitive to static I we electric
36. nnections to Sharp LM64C142 640 x 480 DSTN Color LCD ess 28 3 5 Ethernet interface configuration 29 Chapter 4 Award BIOS Setup 31 4 1 System test and initialization 32 4 1 1 System configuration verification sss 32 4 2 Award BIOS setup ooooooooooooooooooooooooo 33 4 2 1 Eniering setup eret an E eee ee eii 33 4 2 2 Standard CMOS setup 34 4 2 3 BIOS features setup 35 4 2 4 CHIPSET features setup 36 4 2 5 Power management setup oooooooo 37 4 2 6 Load BIOS defaults ee ee ee ee ee ee 38 4 2 7 Load setup defaults 39 4 2 8 Change password seen 40 ASe ad de Me oi LE EE N 41 4 2 10 Auto detect hard disk 42 42 Ll Saver exit setup iu etes 42 4 2 12 Exit without saving essere 42 Chapter 5 SVGA Setup EE aa 43 5 1 Before you begin coooocoooooooooooo o o oooooo o oo oo 44 5 2 InstallatiOn 0er OE EE ER ENEE 45 5 3 Simultaneous display mode e 45 SA Sleep mode eerie eerie eroe eae net Ge ore oon eu See ee GER es eue 45 5 5 Driver installation Windows 3 1 amp DOS 46 5 5 1 Necessary prerequisites 46 3 5 2 Before you Decisi n 46 519 3 Windows Setup una angan ama 46 5 5 4 Changing display drivers in Windows
37. on the board has a number of jumpers that allow you to configure your system to suit your application The table below lists the function of each of the board jumpers and connectors Table 2 1 PCM 4823 4823L jumpers Label Function J2 DOC 2000 address setting J3 LCD power selector J4 Clear CMOS J6 COM selector 8 PCM 4823 4823L User s Manual Table 2 2 PCM 4823 4823L connectors Label Function CN1 Power connector 5 V 12 V CN2 Floppy disk connector CN3 PC 104 connector CN4 Parallel port connector CN5 PC 104 connector CN6 Flat panel connector CN7 Hard disk connector CN8 IR connector infrared CN9 COM connector CN10 Ethernet connector CN11 Power connector 5 V 12 V CN12 COM connector CN13 PS 2 keyboard PS 2 mouse CN14 CRT display connector J5 Reset switch Chapter 2 Installation 9 2 2 Locating jumpers oPinleooroooonoooosoocoo 9 vn os t De Am486DX2 66 Am4860X4 100 Am486DX5 133 VT82C4966 I Pint Pini sysvew aos Ir ima Foo i qa vumm o a DE te 9 9 EET TNT p Dn 22 Zou Im f ut Jumm In eooe o COM1 la Con 10BASE KB MS Figure 2 1 PCM 4823 4823L jumpers 10 PCM 4823 4823L User s Manual 2 3 Locating conne
38. ooooo o ooooo 15 2 6 1 Installing SIMMS esee 15 2 7 IDE hard drive connector CN7 ee 16 2 7 1 Connecting the hard drive esse ee ee ee ee 16 2 8 Keyboard and PS 2 connector CN13 17 2 9 Power connector CN11 ooooooooooooooooooooooooooo 17 2 9 1 Main power connector 5V 12V CN11 17 2 10 IR connector CNN ese ee ee see ee ee Ge ee ee ee ee 17 2 11 Serial ports CN12 CN9 ooooooooooooooo ooooo 18 2 11 1 COMI RS 222 port CN12 ooooWooWooomom 18 2 11 2 COM2 RS 232 422 485 selection CNO 18 2 12 VGA interface connections oooooo oooo ooo 19 2 12 1 CRT display connector CN14 19 2 12 2 Flat panel display connector CN6 19 2 13 Ethernet interface connections ooooooooooo 20 2 13 1 10Base T RJ 45 connector CN10 20 Chapter 3 Software Configuration 21 3 1 Introductio scii N AE 22 3 2 Utility disk ooooooooooooooooooooooocooo 22 3 3 VGA display software configuration 24 3 4 Connections for four standard LCDS 25 3 4 1 Connections to Sharp LM64183P 640 x 480 DSTN MONO LCD eee 25 3 4 2 Connections to PLANAR EL 640 x 480 ADA EL 26 3 4 3 Connections to Toshiba LTM10C042 640 x 480 TFT Color LCD 27 3 4 4 Co
39. ort connector CNA esses 61 A 12 IR connector CNN 62 A 13 System YO ports 63 A 14 DMA channel assignments 64 A 15 Interrupt assignments 64 A 16 Ist MB memory map 65 Appendix B Installing PC 104 Modules 67 BI Installing PC 104 modules ss 68 Appendix C DOC 2000 Installation Guide 71 C 1 DiskOnChip 2000 quick installation guide 72 C 1 1 DiskOnChip 2000 installation instructions 72 C 1 2 Additional information and assistance 73 CHAPTER General Information This chapter gives background informa tion on the PCM 4823 4823L Sections include Card specifications Card layout and dimensions 1 1 Introduction The PCM 4823 4823L is the ultimate cost effective solution for limited space applications It offers all the functions of an AT compatible industrial computer on a single board and only occu pies the space of a 3 1 2 hard drive The PCM 4823 4823L comes with an embedded high performance 5x86 processor and audio on board For maximum performance the PCM 4823 4823L also supports an EDO FPM DRAM SIMM socket that can accept up to 32 MB memory On board features include an Ethernet interface support for a VL Bus Enhanced IDE interface with up to Mode 3 transfer protocol one parallel port two serial ports RS 232 and
40. r computer select the desired display settings from the Display property dialog box 2 Click on Test to test the newly selected graphics mode A color test screen should appear followed by the Testing Mode window 3 Click on Yes to continue Click on Apply to switch to the new graphics mode 4 Since graphics modes are changed dynamically with NT 4 0 you need not shutdown and restart to give effect to the new screen settings 5 8 OS 2 drivers setup procedure 5 8 1 Preliminary steps The following steps must be performed before you install the 65550 554 display driver 1 OS 2 DOS support must be installed 2 If you previously installed SVGA support you must reset the system to VGA mode VGA is the default video mode enabled when OS 2 is installed To restore VGA mode use Selective Install and select VGA for Primary Display For more information on this procedure see the section on Changing Display Adapter Support in the OS 2 User s Guide 5 8 2 Installing from diskette To install this driver do the following steps 1 Open an OS7 full screen or window session 2 Place the 65550 Display Driver Diskette in drive A 3 At the OS 2 command prompt type the following commands to copy the files to the OS 2 drive Chapter 5 SVGA Setup 51 Type A lt ENTER gt to make this the default drive SETUP A C lt ENTER gt where A is the floppy disk drive and C is the hard drive When the se
41. reen below is dis played This sample screen contains the manufacturer s default values for the PCM 4823 4823L ROM ISA BIOS ZCALG6AKE CHOS SETUP UTILITY POWER MANAGEMENT SETUP Power Management Disabled IRQS Activity Primary Doze Timer 32 sec IRQ4 Activity Primary Sleep Timer 2 min TIROS Activity Primary Sleep Mode Sleep IRQ Activity Primary HDD Power Management Disabled IRQS Activity Secondary VGA Activity Wakeup Disabled IRQLO Activity Primary IO Activity Disabled IROLI Activity Primary IRQ12 Activity Primary ESC Quit ti Select Item Fl Help PU PD c Modify FS Old Values ShiftIF2 Color F Load BIOS Defaults F7 Load Setup Defaults Figure 4 5 Power management setup Chapter 4 Award BIOS Setup 37 4 2 6 Load BIOS defaults BIOS DEFAULTS contains the default system values which are the appropriate system parameters for minimum performance These default values are loaded automatically if the stored record created by the Setup program becomes corrupted and therefore unusable ROM ISA BIOS ZCALSAEE CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE amp EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING LOAD BIOS DEFAULT Load BIOS Defaults Y N N LOAD SETUP DEFAUL Esc Quit tl Select Item Fl Sa
42. rmation and assistance 1 Visit M Systems Web site at www m sys com where you can find Utilities Manual Data Sheet and Application Notes In addition you can find the latest DiskOnChip 2000 S W Utilities 2 Contact your dealer for technical support if you need additional assistance and have the following information ready Product name and serial number Description of your computer hardware manufacturer model attached devices etc Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages Appendix C DOC 2000 Installation Guide 73 74 PCM 4823 4823L User s Manual
43. set BIOS configuration data 4 1 System test and initialization These routines test and initialize board hardware If the routines encounter an error in during the tests you will either hear a few short beeps or see an error message on the screen There are two kinds of errors fatal and non fatal The system can usually continue the boot up sequence with non fatal errors Non fatal error messages usually appear on the screen along with the following instructions press lt F1 gt to RESUME Write down the message and press the Fl key to continue the bootup sequence 4 1 1 System configuration verification These routines check the current system configuration against the values stored in the card s CMOS memory If they don t match the program outputs an error message You will then need to run the BIOS setup program to set the configuration information in memory There are three situations in which you will need to change the CMOS settings 1 You are starting your system for the first time 2 Youhave changed the hardware attached to your system 3 The CMOS memory has lost power and the configuration infor mation has been erased The PCM 4823 4823L board s CMOS memory has an integrated lithium battery backup The battery backup should last ten years in normal service but when it finally runs down you will need to replace the complete unit 32 PCM 4823 4823L User s Manual 4 2 Award BIOS setup ROM ISA BI
44. software This method minimiz es the number of chips and eases configuration You can change the display BIOS simply by reprogramming the Flash chip 3 2 Utility disk The PCM 4823 4823L is supplied with a software utility disk This disk contains the necessary file for setting up the VGA display Directories and files on the disk are as follows README DOC AWDFLASH EXE 4823_SYS BIN 4823_CRT BIN 4823_TFT BIN 4823_STN BIN 4823_MON BIN 4823 EL DIN CBROM EXE CT COM FP COM SM COM ON COM OFF COM RSET8019 EXE Figure 3 1 Contents of the PCM 4823 4823L utility disk AWDFLASH EXE This program allows you to write the VGA BIOS files to the BIOS Flash ROM The VGA files all come ready formatted for the PCM 4823 4823L with BIN extensions See README DOC These files support various CRT and flat panel displays They are custom written and are available upon request 4823 SYS BIN This binary file contains the system BIOS 22 PCM 4823 4823L User s Manual 4823_CRT BIN Supports CRT only 4823_TFT BIN default Supports 640 x 480 color TFT Toshiba LTM10C042 4823_STN BIN Supports 640 x 480 color STN DD 8 16 bit displays Sharp LM64C142 4823 MON BIN Supports 640 x 480 dual scan monochrome displays Sharp LM64P8X 837 4823_EL BIN Supports 640 x 480 EL displays PLANAR EL640480 A Series CBROM EXE This program allows you to combine your own VGA BIOS with system BIOS 4823 SYS BIN CT COM Enables CRT di
45. splay only EP COM Enables panel display only SM COM Enables both displays at the same time ON COM Switches to normal display mode OFF COM Switches to sleep mode RSET8019 EXE This program enables you to view the current Ethernet configura tion reconfigure the Ethernet interface medium type etc and execute useful diagnostic functions Chapter 3 Software Configuration 23 3 3 VGA display software configuration The PCM 4823 on board VGA LCD interface supports a wide range of popular LCD EL gas plasma flat panel displays and traditional analog CRT monitors The interface can drive CRT displays with resolutions up to 1280 x 1024 in 16 colors It is also capable of driving color panel displays with resolutions of 1024 x 768 The LCD type is configured completely via the software utility so you do not have to set any jumpers Configure the LCD type as follows 1 Apply power to the PCM 4823 with a color TFT display attached This is the default setting for the PCM 4823 4823L Ensure that the AWDFLASH EXE and BIN files are located in the working drive NOTE Ensure that you do not run AWDFLASH EXE while your system is operating in EMM386 mode 2 Atthe prompt type AWDFLASH EXE and press Enter The VGA configuration program will then display the following FLASH MEMORY WRITER v1 2 Copyright C 1993 Award Software Inc For UIndB866 318L288 68 23 1994 Flash Type File Mane to Progran MENEEENEEEEEN
46. tup program is completed you will need to perform a shutdown and then restart the system in order for changes to take effect A log of the information output during the install can be found in lt root gt OS2 INSTALL DISPLAY LOG 4 After restarting the system perform the following steps 1 Open the OS 2 System folder 2 Open the System Setup folder 3 Open the Display Driver Install Object This step will execute the Display Driver Installation DSPINSTL utility program to finish installation of the new drivers 4 When the Display Driver Install window appears select Primary Display and then select OK 5 When The Primary Display Driver List window appears select Chips and Technologies 65550 554 from the list of adapter types then select OK to install the video driver 6 When the installation is complete you will need to shutdown and then restart the system for the changes to take effect Make sure to remove the install diskette before restarting the system When the system has restarted the display driver will be initialized for 640x480x256 color 60 Hz refresh To switch to a different video resolution color depth or refresh rate follow the steps below 52 PCM 4823 4823L User s Manual 5 8 3 Selecting monitor type Monitor type is initially set to DEFAULT This DEFAULT setting may not allow you to select all resolution refresh combinations that are available for your monitor The following steps can be per
47. ve amp Exit Setup Shift FZ Change Color Figure 4 6 Load BIOS defaults screen 38 PCM 4823 4823L User s Manual 4 2 7 Load setup defaults LOAD SETUP DEFAULTS loads the values required by the system for maximum performance Default ROM ISA BIOS Z2CALSAEE CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE amp EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING LOAD BIOS DEFAULT Load SETUP Defaults Y N N LOAD SETUP DEFAUL Esc Quit tie Select Item Fld Save amp Exit Setup Shift F2 Change Color Figure 4 7 Load SETUP defaults screen Chapter 4 Award BIOS Setup 39 4 2 8 Change password To change the password choose the PASSWORD SETTING option form the Setup main menu and press lt Enter gt 1 If the CMOS is bad or this option has never been used there is default password which is stored in the ROM The screen will display the following messages Enter Password Press lt Enter gt 2 Ifthe CMOS is good or this option has been used to change the default password the user is asked for the password stored in the CMOS The screen will display thefollowing message Confirm Password Enter the current password and press lt Enter gt 3 After pressing lt Enter gt ROM password or the current password us
48. ver is provided for 256 color modes This driver may require special hardware and may not be supported on all systems Chapter 5 SVGA Setup 49 5 6 Windows 95 drivers setup procedure 1 Boot system with VGA or SuperVGA driver 2 Select properties from a menu after right button press 3 Select display 4 Select Change Display 5 Select Change Monitor 6 Select Change Adapter 7 Select Have Disk 5 7 Windows NT drivers setup procedure 5 7 1 Step 1 1 Install Windows NT as you normally would for a VGA display 2 First click the Start button choose Settings and click on Control Panel 3 Choose the Display icon and click on the icon 4 In the Display Properties window click on the Settings tab 5 Click on Change Display Type In the Change Display Type window click on the Change button under Adapter Type This will bring up the Select Device window 5 7 2 Step 2 1 In the Select Device window click on Have Disk Enter source directory where the Windows NT driver files are located 2 Press lt ENTER gt and the name of the Chips and Technologies Video Accelerator driver will appear in the Models list box Select a driver then click OK or press enter 3 A warning panel about Third Party drivers will appear Click the Yes button to finish installation 4 Once the installation is complete the system must be shut down and restarted 50 PCM 4823 4823L User s Manual 5 7 3 Step 3 1 Upon restarting you
49. will be shown the current setup configuration Select Change System Settings from the Option menu Click on the arrow at the end of the Display line You will be shown a list of display drivers Click on the driver you want Then click on the OK button Follow the directions to complete the setup 5 5 5 Changing color schemes After you change display drivers you may notice that the color scheme used by Windows looks strange This is because different drivers have different default colors To change the color scheme select the Control Panel from the Main window Select the Color icon You will be shown the current color scheme Choose a new color scheme and click the OK button Chapter 5 SVGA Setup 47 5 5 6 DOS setup Step 1 Install Windows as you normally would for a VGA display Run Windows to make sure that it is working correctly Then exit Windows Step 2 Place the display driver diskette in drive A Type A lt ENTER gt to make this the default drive Type SETUP lt ENTER gt to run the driver SETUP program Press any key to get to the applications list Using the arrow keys select Windows Version 3 1 and press the lt ENTER gt key Press the lt ENTER gt key to select All Resolutions and then press lt END gt to begin the installation At this point you will be asked for the path to your Windows system directory default CAWINDOWS When the installation is complete press any key to continue Press lt ESC gt followed by Y

Primary

Contents

Download Pdf Manuals

Related Search

Related Contents