Manual - AdvanceTec™ Industries Inc.
Contents
1. AR PURPOSE ARE EXPRESSLY EXCLUDED AND DISCLAIMED AdvanceTec will not be liable or responsible for any loss damage or injury caused by any failure of it s products to operate properly or promptly MOTOROLA and IMPRES are registered in the US Patent amp Trademark Office All other product or service names are the property of their respective owners Motorola Inc 2007 All rights reserved wW AN advancelec 7 INDUSTRIES INC AdvanceTec Industries Inc 1150 NW 163 Drive Miami FL 33169 USA Tel 305 623 3939 Fax 305 623 3996 www advancetec com2. d electronic device which may be damaged if handled roughly or dropped Specifications AC Adapter Input 120V AC 60Hz 22W Output 12VDC 800mA Charger Input 12V DC LED sequence Blinking RED Stand by Blinking GREEN Battery being charged Solid GREEN Battery fully charged NOTE The AdvanceLogic is suitable for indoor use ONLY Warranty Your AdvanceLogic has a one year limited warranty from date of purchase against defects in material and workmanship Under this warranty you may return a faulty product to AdvanceTec and AdvanceTec will either repair or replace the faulty product free of charge To return a faulty product for repair or replacement please call AdvanceTec at 1 800 881 8211 in the USA or 305 623 3939 out of the USA to obtain a Return Material Authorization number This warranty covers only defects in material or workmanship in normal use and not damage from negligent handling misuse charging of batteries other than those the AdvanceLogic was specified and designed to charge or lack of proper care Important Opening of the charger will void this warranty This warranty gives you specific legal rights You may also have other rights which vary from state to state OTHER THAN AS EXPRESSLY SET FORTH ABOVE AdvanceTec DOES NOT MAKE ANY EXPRESS OR IMPLIED WARRANTIES OR REPRESENTATIONS REGARDING THEIR PRODUCTS ANY IMPLIED WARRANTIES OF MERCHANTABILITY NONINFRINGEMENT AND FITNESS FOR A PARTICUL
3. nit in temperatures exceeding 45 C 113 F Do not operate if the unit has been dropped or damaged or if the cord or power supply has been damaged Do not disassemble or attempt to repair or modify the unit This action may be dangerous and will automatically void the warranty General Use 1 Remove the battery from the radio and confirm that the battery chemistry of the battery matches the battery chemistry specified and labeled on the battery adapter plate Place the battery onto the battery adapter plate as you would onto the radio matching the inside battery contacts the ones that would make contact with the radio with the contacts of the battery adapter plate If you are using a Motorola IMPRES radio a specially designed drop in adapter cup can be used to condition and charge the battery through the outer battery contacts without having to remove the battery from the radio The battery alone or the battery attached to the radio can be accommodated in the Drop in adapter cup The drop in adapter cup will accommodate Ni Cd Ni MH Li lon and Li Poly chemistry batteries in the one cup Ask your AdvanceTec sales representative for details NOTE If the battery on the IMPRES radio is not an IMPRES battery the unit will charge but not recondition the battery 4 Once the battery is inserted onto the battery adapter plate the Red Stand by LED will turn off and the Green LED will blink indicating that
4. r available to accurately determine the capacity of the battery If no analyzer is available it is suggested that the battery be taken to your local two way dealer to confirm the status of the battery before discarding the battery Trouble Shooting 1 If the blinking Red LED indicator does not light after the AC adapter is plugged into the wall outlet a Check that the wall socket is powered and that the AC adapter is properly seated in the outlet b Check that the plug into the unit or the cigarette lighter plug into the cigarette lighter adapter power point if being used in a vehicle is properly seated c If being used in the vehicle check that the fuse in the cigarette lighter plug is intact and has not blown To locate the fuse unscrew the end metal tip of the cigarette lighter plug Replace the fuse only with a 3 Amp fuse 2 If the Red LED indicator lights with the battery in place a Remove the battery and replace it ensuring that the battery is properly seated b Check the battery voltage to determine if the battery is still useful c Remove the battery to check for visible damage or interference with the contacts d Verify the battery type and or chemistry for compatibility with the battery adapter plate Warning 1 Do not use an AC or DC adapter other than those supplied with the unit or purchased from AdvanceTec 2 Do not short circuit the output on the units 3 The unit is a highly sophisticate
5. the battery is being charged 5 If the Green LED does not light and the blinking Red LED remains on with the battery in place refer to Trouble Shooting further on in these instructions 6 When the battery is fully charged the Green LED will light steady indicating that the battery is fully charged and that the unit has entered the Maintenance Mode 7 If the battery is removed from the unit before the full charge cycle has been completed the blinking Red LED indicator will turn on To recommence the charging cycles replace the battery on the unit It is quite safe to remove the battery from the unit prior to completing the full charging cycle 8 While in the maintenance mode the unit will keep the battery at 100 peak condition without ever overcharging the battery 9 During the charging cycle the unit and the battery may become warm This is quite normal and is not harmful to either the battery or the Radio NOTE If the battery is new and is being charged for the first time the new battery may cause the Red and Green LEDs to blink alternately for a short time If this should occur leave the battery on the unit and the Red blinking LED will stop within two minutes If the alternating blinking Red and Green LEDs do not stop within two minutes it would appear that the battery is defective 2 Before replacing a defective battery it is suggested that the battery be placed on an AdvanceTec Analyzer or another reliable analyze
6. wW ACVANCEIEC Warning The Advancelogic is designed to accommodate INDUSTRIES INC e Ni Cd and Ni MH battery chemistries of a radio model on one battery adapter plate and e Li lon and Li Poly battery chemistries of a radio AdvanceLogic model on a different battery adapter plate The use of battery chemistry on a battery adapter plate not Part AT2000 AL specified for that chemistry may cause swelling in the battery or burst the battery causing personal injury and User Manual damage This unit is NOT to be used with Lead Acid Carbon Zinc Alkaline Mercury Silver Lithium or any other battery other than the specified Ni Cd Ni MH Li lon and Li Poly batteries Set Up 1 Insert the male round metal plug at the end of the cable of the AC power supply supplied into the corresponding female socket on the back of the unit 2 Plug the AC power supply into a suitable wall outlet At this point the red LED indicator will light and blink to indicate Stand By position 3 The unit is designed for use with interchangeable battery adapters The unit is supplied set up with a battery adapter plate installed as specified by the user Battery adapter model purchased may differ l C AUTI O N tt in th le pict i i a Always plug the power supply into the unit BEFORE you plug it into a standard power outlet Always remove the power supply from the outlet BEFORE you unplug it from the unit Do not operate the u
Download Pdf Manuals
Related Search