Home

NT401 user manual english free

1. 37 NT401 Oil Service Tool Manual_English_V1 01 5 OBDII EOBD Operations OBD II EOBD menu lets you access all OBD service modes According to ISO 9141 2 ISO 14230 4 and SAE J1850 standards the OBD application is divided into several sub programs called Service xx Below is a list of OBD diagnostic services e Service 01 request current powertrain diagnostic data e Service 02 request powertrain freeze frame data e Service 03 request emission related diagnostic trouble codes e Service 04 clear reset emission related diagnostic information e Service 05 request oxygen sensor monitoring test results e Service 06 request on board monitoring test results for specific monitored systems e Service 07 request emission related diagnostic trouble codes detected during current or last completed driving cycle e Service 08 request control of on board system test or component e Service 09 request Vehicle Information When OBDII EOBD application is selected from Home screen the service tool starts to detect the communication protocol automatically Once the connection has been established a menu that lists all of the tests available on the identified vehicle displays Menu options typically include e System Status e Read Codes e Freeze Frame Data e Erase Codes e Live Data e M Readiness e O2 Sensor Test e On board Monitor Test e Component Test e Vehicle Information e Modules Present e Code Lookup
2. E Engine Coolant Temperature Short Term Fuel Trim Bank 1 e Long Term Fuel Trim Bank 1 Figure 5 16 Sample Custom Datastream Selection Screen NOTE To deselect an item select it again and then press the ENTER key Alternatively use the function keys SELECT ALL and CLEAR ALL to select or deselect all items at once 3 When finished selection use the function key VIEW DATA to display selected items 44 NT401 Oil Service Tool Manual_English_V1 01 Custom List Md Number of DTCs O Fuel Systems 1 Status Fuel Systems2 Status Calculate load value I Engine Coolant Temperature Short Term Fuel Trim Bank 1 x o o Sy Figure 5 17 Sample Datastream Screen 5 5 Freeze Frame Freeze Frame menu displays freeze frame data a snapshot of critical vehicle operating conditions automatically recorded by the on board computer at the time of the DTC set Itis a good function to help determine what caused the fault gt To view freeze frame data 1 Select Freeze Frame from the Diagnostic Menu Details of freeze frame data displays Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 02 Monitor Test 8 On board Monitor Test Figure 5 18 Sample Diagnostic Menu Screen 2 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data If no fr
3. NOTE Not all function options listed above are applicable to all vehicles Available options may vary by the year model and make of the test vehicle A The selected mode is not supported message displays if the option is not applicable to the vehicle under test 5 1 System Status System Status option open a screen with a summary of system status of the vehicle under test To view summary system status of a vehicle 1 Scroll with the arrow keys to highlight System Status from Diagnostic Menu and press the ENTER key Diagnostic Menu 1 System Status 2 Read Codes A e 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 O2 Monitor Test 8 On board Monitor Test 38 NT401 Oil Service Tool Manual_English_V1 01 Figure 5 1 Sample Diagnostic Menu Screen 2 A screen with detailed information displays MIL Status Code Found Monitors N A Monitors OK Monitors INC Figure 5 2 Sample System Status Screen 5 2 Read Codes Read Codes menu lets you read both stored codes and pending codes found in the control unit Typical menu options include e Stored Codes e Pending Codes Diagnostic trouble codes stored in a control module are used to help identify the cause of a trouble or troubles with a vehicle These codes have occurred a specific number of times and indicate a problem that requires repair Pending codes are also referred to as maturing codes that indicate intermittent faults If the fault
4. CADILLAC Model CHEVROLET Century GMC PONTIAC j 2 Lacrosse 3 LeSabre Wyner Year 4 Park Avenue 7 OLDSMOBILE 5 Rainier SATURN 1 2001 2005 2 1999 2000 3 1997 1998 6 Regal 7 Rendezvous 8 Riviera Figure 4 8 Sample Vehicle Identification Screens 3 When the vehicle is identified a procedure screen displays Manual Reset With Driver Information Center 1 Turn the ignition to RUN without starting the engine 2 Fully press and release the accelerator pedal slowly three times within 5 seconds The CHANGE OIL SOON indicator flashes to indicate the system is resetting 3 Turn the ignition to OFF 4 Start the vehicle The oil life changes to 100 5 If the CHANGE OIL SOON indicator comes back on reset Figure 4 9 Sample Manual Reset Instructions Screen 4 Follow all on screen instructions to perform the manual mechanical reset 5 Press function key OK to return 4 2 3 Auto Reset Auto Reset is a bi directional communication procedure directed by the service tool The service tool displays guides for you through the process A number of instructions that require a response to continue display including an option to clear any stored codes once the interval has been reset Follow the on screen instructions 4 2 3 1 AUDI SEAT SKODA VW Operations Oil Service menu allows to reset the Service Reminder in vehicles so equipped This function will automatically access the Instrum
5. PURPOSE OR USE SHALL BE LIMITED TO THE DURATION OF THE FOREGOING LIMITED WRITTEN WARRANTY OTHERWISE THE FOREGOING LIMITED WARRANTY IS THE CONSUMER S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED FOXWELL SHALL NOT BE LIABLE FOR SPECIAL INCIDENTAL PUNITIVE OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED 2 NT401 Oil Service Tool Manual_English_V1 01 TO LOSS OF ANTICIPATED BENEFITS OR PROFITS LOSS OF SAVINGS OR REVENUE LOSS OF DATA PUNITIVE DAMAGES LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT COST OF CAPITAL COST OF ANY SUBSTITUTE EQUIPMENT OR FACILITIES DOWNTIME THE CLAIMS OF ANY THIRD PARTIES INCLUDING CUSTOMERS AND INJURY TO PROPERTY RESULTING FROM THE PURCHASE OR USE OF THE PRODUCT OR ARISING FROM BREACH OF THE WARRANTY BREACH OF CONTRACT NEGLIGENCE STRICT TORT OR ANY OTHER LEGAL OR EQUITABLE THEORY EVEN IF FOXWELL KNEW OF THE LIKELIHOOD OF SUCH DAMAGES FOXWELL SHALL NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE LIMITED WARRANTY OR LOSS OF USE DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED 6 Some states do not allow limitation of how long an implied warranty lasts so the one year warranty limitation may not apply to you the Consumer Some states do not allow the exclusion or limitation of incidental and consequential damages so certain of the above limitations or exclusions may not apply to you the Consumer This limited warranty gives the Consumer
6. specific legal rights and the Consumer may also have other rights which vary from state to state 3 NT401 Oil Service Tool Manual_English_V1 01 Safety Information For your own safety and the safety of others and to prevent damage to the equipment and vehicles read this manual thoroughly before operating your service tool The safety messages presented below and throughout this user s manual are reminders to the operator to exercise extreme care when using this device Always refer to and follow safety messages and test procedures provided by vehicle manufacturer Read understand and follow all safety messages and instructions in this manual Safety Message Conventions Used We provide safety messages to help prevent personal injury and equipment damage Below are signal words we used to indicate the hazard level in a condition Indicates an imminently hazardous situation which if not avoided will result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided could result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided may result in moderate or minor injury to the operator or to bystanders Important Safety Instructions And always use your service tool as described in the user s manual and follow all safety messages e Do not route the test cable in a manner that would int
7. Codes steps 5 4 Live Data Live Data menu lets you view and record real time PID data from the electronic control module Menu options typically include e Complete Data List e Custom Data List 41 NT401 Oil Service Tool Manual_English_V1 01 5 4 1 Complete Data List Complete Data List menu lets you view all live PID data from a selected system To view all live PID data 1 Scroll with the arrow keys to highlight Live Data from Diagnostic Menu and press the ENTER key Diagnostic Menu iii 1 System Status 3 Erase Codes 4 Live Data 7 O2 Monitor Test 8 On board Monitor Test Figure 5 9 Sample Diagnostic Menu Screen 2 Select Complete List from the menu and press the ENTER key to display the datastream screen 1 Complete List 2 Custom List Figure 5 10 Sample Live Data Menu Screen 3 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data Complete List Number of DTCs 0 Eo Fuel Systems 1 Status E Fuel Systems2 Status Engine Coolant Temperature Short Term Fuel Trim Bank 1 Calculate load value fo 3 Figure 5 11 Sample Complete List Screen 42 NT401 Oil Service Tool Manual_English_V1 01 4 Scroll with the up and down arrow keys to highlight a line if the One Graphic on the bottom is highlighted it indicates the graphing is available for the selected line Press the function key One
8. Graphic to display the PID graph Engine RPM 1225 rem 2437 Figure 5 12 Sample PID Graph Screen 5 Press the function key Two Graphics to display two PID graphs in one screen Engine RPM rem Vehicle Speed Sensor 0 mph 0 Figure 5 13 Sample Two PID Graph Screen 6 Press the function key Merge Graph to display two PID plots in one coordinate for easy and intuitive diagnosis Engine RPM Vehicle Speed Sensor N Figure 5 14 Sample Merge Graph Screen 7 To record the data to memory of the service tool use the function key SAVE and press Stop Saving to stop recording at any time 8 Select Text to return to text viewing of PID data 43 NT401 Oil Service Tool Manual_English_V1 01 9 Press Pause to suspend collecting data and use the Start key to resume collecting data 10 Use the Back key to return to diagnostic menu 5 4 2 Custom Data List Custom Data List menu lets you to minimize the number of PIDs on the data list and focus on any suspicious or symptom specific data parameters b To create a custom data list 1 Select Custom List from the menu and press the ENTER key Live Data 1 Complete List 2 Custom List Figure 5 15 Sample Live Data Menu Screen 2 The custom datastream selection screen displays Scroll with the up and down arrow keys to highlight a line press the ENTER key and then repeat the action to make more selections Ei Numbers of DTCs PETE Ll rue Sytemaz St a El Oncala o
9. Screen 4 Ascreen with Success message comes up once the oil light reset has been done successfully DEMET G Success Figure 4 61 Sample Service Reset Successful Screen NOTE If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 34 NT401 Oil Service Tool Manual_English_V1 01 4 2 3 8 Vauxhall Operations This section illustrates how to do oil reset automatically on Vauxhall To perform oil reset on Vauxhall 1 Scroll with up and down arrow keys to highlight a function and press ENTER key to confirm 1 Reset Service Interval Figure 4 62 Sample Service Interval Resetting Menu Screen 2 Follow on screen instruction and press any key to continue Reset Service Interva Please press brake pedal during service interval reset Figure 4 63 Sample Service Interval Resetting Instruction Screen 3 Wait for a few seconds and a screen with Reset Successfully message displays once the service interval reset has been done successfully Reset Service Interva Reset Successfully Figure 4 64 Sample Service Interval Reset Successful Screen NOTE 35 NT401 Oil Service Tool Manual_English_V1 01 If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem
10. already have a Foxwell account click here to Sign in if you are new to Foxwell simply complete the forms below to create an account and register your product s Part No NT401 x Serial No Register Password How to find your products serial number and register password or Submit j Reset Cancel Figure 8 1 Sample Register Products Screen 2 Select your scanner part number enter your serial number and initial register password which can be found by turning on your scan tool and selecting Setup gt About and click Submit to continue F XWE LL a Sign in Gy er ee sy ENAN Thank you for purchasing F omwei producia Te Se al number and register paaaword can be found by sebecting Setup gt About from pour ecancer ed me De Of pour product Gy EDI POL pad 5 a latest ippo Ml pre i product infannation g t updates fer pour scan usera i you already have a Forvwoll account dick hort duel i El E Lai Pe Pad Part Ho Seal Ho e Register PEISA Figure 8 2 Sample Serial No amp Password Entering Screen 63 NT401 Oil Service Tool Manual_English_V1 01 3 Read through our Register Information and click Agree to continue events are notified in such manner 12 Advertising Any promotional activities such as making advertisement showing users product on the Foxwell Website freight payment service commercial conditions guarantee and product description are done betwe
11. annie saad arn Paid eaiae pais Haw cieaanee A 15 4 2 3 1 AUDI SEAT SKODA VW OperatiONS ccccccccccccooooccononcnnnnnnnnnnnnnnononnnnnnnnncnnnnnnononnnnnnnns 15 4 2 3 2 BMW OPSrallONS ii ii 18 OBDINTOPIN CO Meco miciccadapisiaicicae tl talladas 18 A O O eamerune ae oaueee 23 4 2 9 3 Fla rOPperaloN Sri 23 42 34 GM Operations arena A eee 25 4 2 3 5 Mercedes Benz Operations rica ica nidad 28 4 2 3 6 Land Rover Operallons a 30 42 37 SAAD Operaio eas anced esse cas toes did 33 4 23 88 Vauxhall Operations sanna A A 35 4 23 9 WOIVO OPETAN S aisar an a OA seacqosebeaiaasaesucasabeaneenaesaugioe 36 gt OBDI EOBD O ERA TONS lt lt e 38 MO YS TEMO TA TUS cla aaa EEE A EAA E AEA AES EEE A E 38 5 NT401 Oil Service Tool Manual_English_V1 01 SZ READ CODES cheers act hs aces sas e eee eects ah cea tak sees ate el dad 39 53 ERASE CODES AA AAA A AA ee 41 SALVE DAT Arann ia isls 41 5 4 1 Complete Data Sd A ad 42 Ae Custom Data stas titan sa 44 SO PREEZE FRAME a A E RA aa 45 5 6 READ I M READINESS STATUS DATA c ooocccoccccoccconcncnnnnoncnnonnncnnrnnnnnnonrnnonnnnnnnnnnrnnonrnnnnrnnnnnnenrncanenanons 46 DF O2 MONTOR TEST O 48 5 90 ON BOARD MONITOR TEST similar lila land 49 5 9 COMPONENT TESTS do 51 5 10 REQUEST VEHICLE INFORMATION caia ii datada 52 SI MODULES PRESENT iian a a e a E i aale Deut aaesaaseameas 53 Cou LOOK Poltica 54 O PLAYBACK DATA ii olas less 56 TOY TEM SETUP Sa it asii 57 TA SELECT LANGUAGE an a 57 ORANGE UNITS a ias 58 7 3 CO
12. specific needs Depending on the needs of text entry it automatically shows the most suitable keypad e classic QWERTY keyboad for input of texts that contain both letters and numbers e numeric keyboard for input of numbers e alphabet keyboard for input of letters To input text with the service tool 1 When you are requested to input text press the function key Keyboard and the keyboard displays 10 NT401 Oil Service Tool Manual_English_V1 01 Distance driven since last o 1000 The value can be set between 0 and 5000 Figure 3 1 Sample Input Text Screen 2 Scroll with the arrow keys to highlight your desired letter or number and press the ENTER key to confirm Figure 3 2 Sample QWERTY Keyboard Screen 3 To delete a letter or number use the function key Previous to move the cursor to it and then press the Backspace button 4 When finished the entry press Finish key to continue 4 Instructions 4 1 gt This section illustrates how to use the service tool to reset oil service light oil inspection light service mileage service intervals and more on 32 vehicle manufacturers NOTE All software screens shown in this manual are examples actual test screens may vary by the year model and makes of the test vehicle Observe the menu titles and onscreen instructions to make correct option selections Vehicle Identification The vehicle identification information presented is provided by the ECM of the
13. still exists please contact your local dealer for assistant 4 2 3 9 Volvo Operations This section illustrates how to do oil reset on Volvo To do oil reset on Volvo 1 Scroll with up and down arrow keys to highlight Auto Reset from the oil reset menu and press ENTER key to confirm Oil Reset 1 Manual Reset 2 Auto Reset Figure 4 65 Sample Oil Reset Menu Screen 2 A list of vehicle models displays Scroll with up and down arrow keys to highlight the vehicle being tested and press the ENTER key to continue 9 80 13 V50 14 V70 00 08 15 V70 08 V70 XC 01 XC70 07 Figure 4 66 Sample Vehicle Model Selection Screen 3 Select the year of the vehicle being tested and press the ENTER key to confirm 36 NT401 Oil Service Tool Manual_English_V1 01 Version Figure 4 67 Sample Vehicle Year Selection Screen 4 Select a service function from the Oil Reset menu and press ENTER key to send a command to the vehicle ECU Oil Reset 1 Reset SRL data Figure 4 68 Sample Oil Reset Menu Screen 5 Wait for a few seconds and the Success message screen comes up once the oil reset has been done successfully Reset SRL data Success Figure 4 69 Oil Reset Successful Screen NOTE If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant
14. to off position 0 Figure 4 55 Sample Oil Reset Instruction Screen 6 Set the ignition switch to on again and press the function key OK to continue or press Cancel to quit the oil light reset Freelander 2 LR2 Set the ignition switch to on position 2 Figure 4 56 Sample Oil Reset Instruction Screen 7 A screen with Complete message comes up once the oil light reset has been done successfully 32 NT401 Oil Service Tool Manual_English_V1 01 Freelander 2 LR2 Complete Figure 4 57 Sample Oil Reset Successful Screen NOTE If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 4 2 3 7 Saab Operations This section illustrates how to do oil reset on Saab gt To do oil reset on Saab 1 Scroll with up and down arrow keys to highlight Auto Reset from the oil reset menu and press ENTER key Oil Reset 1 Manual Reset 2 Auto Reset E Figure 4 58 Sample Oil Reset Menu Screen 2 Select the function you wish to test and press the ENTER key to confirm 33 NT401 Oil Service Tool Manual_English_V1 01 DENT 1 ON 365 Days 2 ON 730Days 3 OFF Figure 4 59 Sample Service Reset Menu Screen 3 The Oil Reset menu displays Press ENTER key to send a command to the ECU Oil Reset 1 Daycounter Figure 4 60 Sample Oil Reset Menu
15. vehicle make to look for DTC definitions Press the Back key to exit l Trouble Codes y Fuel Volume Regulator Control Circuit Open Figure 5 41 Sample Trouble Codes Screen 55 NT401 Oil Service Tool Manual_English_V1 01 6 Playback Data The PlayBack option leads to screens for review of recorded test results gt To review recorded data 1 Scroll with the arrow keys to highlight PlayBack from home screen and press the ENTER key Application OBDII OilReset Setup PlayBack Figure 6 1 Sample Home Screen 2 A screen with a list of test records displays If no data is recorded the message No Data available is displayed 1 Datastream gt scan MAKE EOBD savefile 2 Ecu Information gt scan MAKE EOBD savefile 3 Trouble Code gt scan MAKE USA Ford savefile 4 Trouble Code gt scan MAKE Asia Hyundai savefile 5 Ecu Information gt scan MAKE EUROPE Bmw savefile 6 Ecu lnformation gt scan MAKE EUROPE Fiat savefile 7 Ecu Information gt scan MAKE EOBD savefile i Figure 6 2 Sample Playback Screen 3 Scroll with the arrow keys to highlight a vehicle record and press the ENTER key Details of the test record displays Use the up and down arrow keys to scroll through data to select lines Read Codes Intake Air Temperature Sensor 1 Circuit High Throttle Pedal Position Sensor Switch A Circuit High Throttle Pedal Position Sensor Switch B Circuit Low Throttle Pedal Posit
16. vehicle being tested Therefore certain attributes of the test vehicle must be entered into the service tool to ensure the data displays correctly The vehicle identification sequence is menu driven you simply follow the screen prompts and make a series of choices Each selection you make advances you to the next screen Exact procedures may vary somewhat by vehicle To identify a vehicle 11 NT401 Oil Service Tool Manual_English_V1 01 1 Scroll with the arrow keys to highlight Oil Reset from the Application menu and press the ENTER key to start If you have the application assigned to one of the function keys at the bottom of the screen you can alternatively press the function key to start the application Application saasaa rr a BB OBDII OilReset Setup PlayBack Figure 4 1 Sample Application Menu Screen 2 A screen with a list of vehicles displays Select the vehicle you wish to test and press the ENTER key Application Scan European COCO Abarth Acura Alfa romeo AUDI 6 O BMW Chrysler FIAT Ford Figure 4 2 Sample Vehicle Manufacturer Selection Screen 3 On each screen that appears select the correct option and then press the ENTER key Do this until the complete vehicle information is entered and the menu of controller selection displays Model Year 5 9 013013 2 C02 4 Reo LAO TO Sag hide tod a ieee j Passenger Car 3i T EDO a LD Tri MPM Incomolete amp 612006 La hi el
17. vehicles The Service Indicator System SIA is designed to alert the driver when the vehicle is due for a service The BMW Maintenance System includes the Engine Oil Service and Inspections minor service and II major service Different years and models have display variations depending on the instrument cluster level type gt To perform oil service on BMW 1 Scroll with up and down arrow keys to highlight Auto Reset from the Oil Reset menu and press ENTER to start Oil Reset E 1 Manual Reset 2 Auto Reset Figure 4 16 Sample Oil Reset Menu Screen 2 The connector type selection screen displays Scroll with arrow keys to select the connector type for the vehicle being tested BMW 1 BMW 20Pin 2 BMW 16Pin Figure 4 17 Sample BMW Vehicle Connector Screen OBDII 16PIN Connector BMW vehicles with OBDII connector have more service functions than those with 20 PIN connector There are two ways to complete oil reset on 16 PIN Connector vehicles e CBS reset e CBS correction CBS reset gt To perform oil service functions on BMW with OBDII connector 1 To complete the service functions automatically scroll with up and down arrow keys to select CBS Reset from the Oil Reset menu and press ENTER key to confirm 18 NT401 Oil Service Tool Manual_English_V1 01 Oil Reset 6 1 CBS reset 2 CBS correction Figure 4 18 Sample Oil Reset Menu Screen NOTE Not all functions listed are applicable to all vehi
18. Gross Weight 1 2Kg Protocols SAE J1850 VPW and PWM ISO 9141 2 ISO 14230 2 KWP 2000 ISO 15765 4 CAN 3 Getting Started This section describes how to provide power to the service tool provides brief introductions of applications loaded on the service tool and display screen layout and illustrates how to input text and numbers with the service tool 3 1 Providing Power to Scanner Before using the service tool make sure to provide power to the service tool The unit operates on any of the following sources e 12 volt vehicle power e USB connection to personal computer 3 1 1 Connecting to Vehicle Power The service tool normally powers on whenever it is connected to the data link connector DLC gt To connect to vehicle power 1 Locate the data link connector DLC The DLC is generally located under the dash on the driver side of the vehicle 9 NT401 Oil Service Tool Manual_English_V1 01 2 Attached the diagnostic cable to the service tool and tighten the captive screws to ensure good connection 3 Connect a correct adapter to the data cable according to the vehicle being serviced and plug it into the vehicle DLC 4 Switch the ignition key to the ON position 5 The service tool automatically boots up IMPORTANT Never try to provide power for the service tool from USB connection when the service tool is communicating with a vehicle 3 1 2 Connecting to Personal Computer with USB Cable gt The service t
19. NFIGURE BEEPER uratconciaa innatas nadia ioaaa 59 124 TEST KEYPAD a 59 FONG KEYPAD tt dais 60 TH TOOL INFORMATION A AA Geneon 61 Lif CONFIGURE SHORTCUT KEYS estacionado alada 61 UPDATES e ds 62 8 1 REGISTER THE SCANNER ccccccccesccceesceceuceceeuceceuueeceeueeseueeeeuceceueeeecueeeeueeseueeeeeueeseeueeseeueesees 62 o Z UPDATE THE OCANNER de do 67 6 NT401 Oil Service Tool Manual_English_V1 01 1 Using This Manual We provide tool usage instructions in this manual Below is the conventions we used in the manual 1 1 Bold Text Bold text is used to highlight selectable items such as buttons and menu options Example Press the ENTER button to select 1 2 Symbols and Icons 1 2 1 Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot e Example When System Setup is selected a menu that lists all available options displays Menu options include e Languages e Unit e Beep e Keypad Test e LCD Test e About e Shortcuts 1 2 2 Arrow Icon gt gt An arrow icon indicates a procedure Example To change menu language 1 Scroll with the arrow keys to highlight Language on the menu 2 Press the ENTER button to select 1 2 3 Note and Important Message Note A NOTE provides helpful information such as additional explanations tips and comments Example NOTE Test results do not necessarily indicate a faulty component or system Important IMPORTANT indicate
20. Sample Diagnostic Menu Screen 2 Scroll with the arrow keys to highlight an O2 sensor and press the ENTER key to confirm A screen with details of the selected sensor displays O2 Monitor Tes 1 02 Bank1 Sensor 2 O2 Bank1 Sensor2 Figure 5 24 Sample O2 Monitor Test screen 3 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data 48 NT401 Oil Service Tool Manual_English_V1 01 O2 Bank1 Sensor T Figure 5 25 Sample O2 Bank1 Sensor 1 Screen 4 Press Enter key to view data of selection 81 Module Test Value 10 Min Limit oa Max Limit Figure 5 26 Sample data of 81 screen 5 Press the BACK key to exit and return 5 8 On Board Monitor Test The On Board Monitor Test function is useful after servicing or after clearing a vehicle ECU s memory It receives test results for emission related powertrain components and systems that are not continuously monitored for Non CAN vehicles And for CAN vehicles it receives test data for emission related powertrain components and systems that are and are not continuously monitored It is vehicle manufacturer who is responsible for assigning test and component IDs NOTE Test results do not necessarily indicate a faulty component or system gt To request on board monitor test results 1 Scroll with the arrow keys to highlight On Board Monitor Test from Diagnost
21. Trademarks FOXWELL is trademark of Shenzhen Foxwell Technology Co Ltd All other marks are trademarks or registered trademarks of their respective holders Copyright Information 2013 Shenzhen Foxwell Technology Co Ltd All rights reserved Disclaimer The information specifications and illustrations in this manual are based on the latest information available at the time of printing Foxwell reserves the right to make changes at any time without notice Visit our website at www foxwelltech com For Technical Assistance send us email at support foxwelltech com 1 NT401 Oil Service Tool Manual_English_V1 01 One Year Limited Warranty Subject to the conditions of this limited warranty Shenzhen Foxwell Technology Co Ltd FFOXWELL warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of one 1 year In the event this product fails to operate under normal use during the warranty period due to defects in materials and workmanship FOXWELL will at its sole option either repair or replace the product in accordance with the terms and conditions stipulated herein Terms and Conditions 1 If FOXWELL repairs or replaces the product the repaired or replaced product shall be warranted for the remaining time of the original warranty period No charge will be made to the customer for replacement parts or labor charges incurred by FOX
22. WELL in repairing or replacing the defective parts 2 The customer shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable a The product has been subjected to abnormal use abnormal conditions improper storage exposure to moisture or dampness unauthorized modifications unauthorized repair misuse neglect abuse accident alteration improper installation or other acts which are not the fault of FOXWELL including damage caused by shipping b The Product has been damaged from external causes such as collision with an object or from fire flooding sand dirt windstorm lightning earthquake or damage from exposure to weather conditions an Act of God or battery leakage theft blown fuse improper use of any electrical source or the product was used in combination or connection with other product attachments supplies or consumables not manufactured or distributed by FOXWELL 3 The customer shall bear the cost of shipping the product to FOXWELL And FOXWELL shall bear the cost of shipping the product back to the customer after the completion of service under this limited warranty 4 FOXWELL does not warrant uninterrupted or error free operation of the product If a problem develops during the limited warranty period the consumer shall take the following step by step procedure a The customer shall return the product to the place of purchase for repair or replacement processi
23. a vee z i Chewglet 2 Cadillac 12 NT401 Oil Service Tool Manual_English_V1 01 Figure 4 3 Sample Vehicle Selection Screens 4 2 Service Reset Operations Oil service reset methods are determined by the vehicle being tested Depending on the vehicle being tested any of the following means displays e Oil Reset With One Button e Manual Reset e Auto Reset 4 2 1 Oil Reset With One Button Oil Reset With One Button is applicable to GM models only It offers quick and simple oil service reset with the click of one button To do Oil Reset With One Button 1 Scroll with up and down arrow keys to highlight Oil Reset With One Button from the Oil Reset menu An Information screen displays Press the function key OK to continue or Cancel key to return to the Oil Reset menu Oil Reset 1 Oil Reset With One Button 2 Manual Reset 3 Auto Reset Figure 4 4 Sample Oil Reset Menu Screen 2 Follow on screen instruction and send a command to reset oil service A screen with Success message displays once the lamp has been reset Press any key to return Oil Life Reset Success Figure 4 5 Sample Oil Reset With One Button Success Screen 3 If the oil service reset failed the following screen displays Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 13 NT401 Oil Service Tool Manual_English_V1 01 Communication No commun
24. alue you want or press the function key Cancel to quit service reset SID Maximum value of time to Service Stored Value 260 Days Figure 4 12 Sample Vehicle Stored Value Screen 4 Enter a valid value and press Finish to continue 16 NT401 Oil Service Tool Manual_English_V1 01 SID Maximum value of time tose Figure 4 13 Sample Service Time Value Entry Screen 5 Press the function key Yes to save and continue or press the function key NO to quit Input Dialog Box 200 Do you want to save and continue Figure 4 14 Sample Input Dialog Box Screen 6 If the service reset has been completed a confirmation message comes up Press any key to return SID Maximum value of time to se The new values have been set success Figure 4 15 Sample Service Interval Reset Successful Screen NOTE e Stored Value is the value of the most recent setup retrieved by NT401 If you change your mind after making new setups it can be used to reset all changed values to original ones It is advised to write down this value before making any changes e l No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 17 NT401 Oil Service Tool Manual_English_V1 01 4 2 3 2 BMW Operations This section illustrates how to reset the oil service lamps on the instrument cluster of BMW
25. anguage About Shortcuts Figure 7 6 Sample Beeper On Off Selection Screen 7 4 Test Keypad Selecting Key Test option opens a screen that allows you to check the functionality of the keypad P To test the keypad 1 Scroll with the arrow keys to highlight Key Test from Setup menu and press the ENTER key 59 NT401 Oil Service Tool Manual_English_V1 01 Application Setup Language Key Test Led Test Shortcuts Figure7 7 Sample Setup Screen 2 Press any key to start test The virtue key corresponding with the key you pressed will be highlighted on the screen if it works correctly FOXWELL Press Any key to test Double F2 to return Figure 7 8 Sample Key Test Screen 1 To quit the test click the F2 function key twice 7 5 LCD Keypad Selecting LCD Test option opens a screen that allows you to check the functionality of the display gt To test the display 1 Scroll with the arrow keys to highlight LCD Test from Setup menu and press the ENTER key to start test Check if there are any missing spots in the LCD screen 60 NT401 Oil Service Tool Manual_English_V1 01 Figure 7 9 Sample LCD Test Screen 2 To quit the test press the Back key 7 6 Tool Information Selecting About option opens a screen that show information about your service tool such as serial number and register password which may be required for product registration gt To view information of your service tool 1 Scroll with the ar
26. ant Monitor Sec Air System Secondary Air System Monitor Oxygen Sens Mon Oxygen Sensor Monitor 10 Oxygen Sens Htr Oxygen Sensor Heater Monitor Exhaust Gas Recirculation System Monitor EGR System Mon NOTE e To review I M Readiness status make sure that the ignition key is switched to ON with the engine off e Not all monitors are supported by all vehicles To retrieve I M Readiness Status data 1 Scroll with the arrow keys to highlight I M Readiness from Diagnostic Menu and press the ENTER key If vehicle supports both types of monitors a screen for monitor type selection displays Select a monitor type and press the ENTER key 46 NT401 Oil Service Tool Manual_English_V1 01 Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 02 Monitor Test 8 On board Monitor Test Figure 5 20 Sample Diagnostic Menu Screen 2 Depending on readiness test one of these 2 screens will be present Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data Since DTCs cleared Malfunction Indicator lamp MIL Status OFF Misfire Monitoring Fuel system Monitoring Comprehensive component Monitoring Catalyst Monitoring Heated Catalyst Monitoring Evaporative system Monitoring Secondary air system Monitoring Figure 5 21 Sample IM Readiness Screen 1 Or T
27. any key to exit and return 8 Update The scanner can be updated to keep you stay current with the latest development of diagnosis This section illustrates how to register and update your scan tool 8 1 Register the Scanner If you are new to FOXWELL please register the scanner first All of your scanners can be registered on One Foxwell ID To register the scanner 1 Visit our site www foxwelltech com and then select Register Products to create a Foxwell ID and register your scan tool Alternatively please visit our website and then select Support gt Updates gt Professional Scanner http www foxwelltech com support3 php id supportUpdate_5 to download the update tool DiagMate to complete the registration If you have already had a Foxwell ID just click the Sign in link http www foxwelltech com login php at the top right of the website to login 62 NT401 Oil Service Tool Manual_English_V1 01 FOXWELL signin cy Free es seamen o Comat Thank you for purchasing Foxwell products You can help us to develop new products that meet your needs and help us give you the best service possible through the life of your product by registering your product When you registered your product s you are allowed to view and modify your account information get the latest product information get updates for your scan tool leave us feedbacks get our professional technical supports and share your successful story with other users If you
28. ation types 1 Scroll with the arrow keys to highlight Modules Present from Diagnostic Menu and press the ENTER key Diagnostic Menu I M Readiness 7 O2 Monitor Test 8 On board Monitor Test 9 Component Test 10 Vehicle Info 11 Modules Present 12 DTC Lookup System Status Figure 5 37 Sample Diagnostic Menu Screen 2 A screen with the module IDs and protocols displays Module Present Protocol Y KWP 2000 Figure 5 38 Sample Module Present Screen 3 Press function key Save to store the readiness data Or use the BACK key to exit and return 5 12 DTC Lookup DTC Lookup menus allows to request DTC definitions stored in the service tool To Look up DTCs 1 Scroll with the arrow keys to highlight DTC Lookup from Diagnostic Menu and press the ENTER key 54 NT401 Oil Service Tool Manual_English_V1 01 Diagnostic Menu 6 I M Readiness 7 02 Monitor Test 8 On board Monitor Test 9 Component Test 10 Vehicle Info 11 Modules Present 12 DTC Lookup 1 System Status Figure 5 39 Sample Diagnostic Menu Screen 2 Enter a valid code number and press the function key Finish DTC Lookup Figure 5 40 Sample DTC Lookup Screen 3 A screen with code number and its definition displays If definition could not be found SAE or Manufacturer Specific the service tool displays DTC definition not found Please refer to vehicle service manual If a P1xxx C1xxx B1xxx or Ul1 xxx code is entered select a
29. ce Tool Manual_English_V1 01 Table of Contents ONE YEAR LIMITED WARRANTY ccccssseccecssseeeeccsseeeeeeaseeeeeeaseeeeeeuseeeeeeaeseeeeeasseeeeeaseesseeaseeesseaens 2 SAFETY INFORMATION tae 4 SAFETY MESSAGE CONVENTIONS USED tac ece t5sdive arias dm 4 IMPORTANT SAFETY INSTRUCTIONS Dacia oe 4 TUSINGTAIS MANUAL iena vastos id 7 ERE NUE Le TN es lt q pen CON o ae es eres wnt as sees hea a cas dace vara eens satin cw ectuaans cane tes naseasea es cena 7 LAS MBOLS AND ICONS serait patna A a EN 7 A SS snes ab E 7 Ns ee AIOW ICOM CPC O Oo O O 7 1 2 3 Note and Important Message iaa 7 INTRODUCTION ones 8 2 SO CANNER DESCRIPTION Siria iaa tilda leida asias 8 2 ACCESSORY DESCRIPTIONS aiir nN e is 9 2 3 TECHNICAL SPECIFICATIONS andoian hea E a aa e ida 9 3 GETING STARTED lt a Vea 9 3 1 PROVIDING POWER TO SCANNER asno dc cea 9 31 1 CONNECIING to Venice PO Wero tn ii 9 3 1 2 Connecting to Personal Computer with USB Cable oooococccccnnccccccccccccncnancncncnnnnnonononnnnnnnnos 10 de APPLICATION OVERVIEW A AT AAA AAA A A 10 Bro INP UN DIALOG BOX coscese aacaneasstcsane asecanen eetanace a E 10 INSTRUCTIONS ad tan e 11 41 VEHICLE IDENTIFICATION stas dd 11 4 2 SERVICE RESET OPERATIONS cscssessesecscsscusescuscnseuecueuscusenseueuseuscuueneusenseuseueuscuvenseueeeuseaseneuses 13 42101 Reset Wih Ope BUNOM rasinn ser ascel aaa 13 Ae Mana THESE sed ana 14 A253 AWO ROS SU icc saras sce sate anea cin xwngaanncamaacsue maecaewiatevawaie
30. cles Available options may very by the model year of the vehicle being tested 2 A screen with available services displays CBS reset 1 Engine Oil 2 Spark plugs 3 Front brakes 4 Rear brakes 5 Coolant 6 Diesel particle filter 7 Brake fluid 8 Microfilter Figure 4 19 Sample CBS Reset Menu Screen 3 Scroll with up and down arrow keys to highlight service you want to perform and press ENTER key to confirm Press Modify to perform the service Engine oil Availability Service counter Figure 4 20 Sample Engine Oil Reset Screen 4 A command to reset the engine oil is sent A screen with ECU default value displays when the lamp has been reset successfully Press any key to return to the function menu 19 NT401 Oil Service Tool Manual_English_V1 01 Engine oil Availability Service counter 8 Figure 4 21 Sample Engine Oil Reset Successful Screen 5 If it fails to reset engine oil the following screen displays Please follow the on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant Engine oil The engine control unit did not execute the CBS reset engine oil If the CBS reset is not accepted also after the second reset attempt carry out troubleshooting in the engine control unit After successfully rectifying the fault repeat CBS reset procedure Rectify the causes of all fault code memory entries Known causes of CBS reset problems Oi
31. does not occur within a certain number of drive cycles depending on vehicle the code clears from memory If a fault occur a specific number of times the code matures into a DTC and the MIL illuminates or blinks To read codes pending codes from a vehicle 1 Scroll with the arrow keys to highlight Read Codes from Diagnostic Menu and press the ENTER key Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes e onaran Figure 5 3 Sample Diagnostic Menu Screen 2 Select Stored Codes Pending Codes and press the ENTER key to confirm A code list including code number and its description displays 39 NT401 Oil Service Tool Manual_English_V1 01 Read Codes 1 Stored Codes 2 Pending Codes Figure 5 4 Sample Read Codes Screen If no DTCs are present the message No Pending Codes Found is displayed If any manufacturer specific or enhanced codes detected select vehicle a make before viewing DTC information Trouble Codes No codes are stored in the module Figure 5 5 Sample No Codes Screen 3 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data Trouble Codes Intake Air Temperature Sensor 1 Circuit High ii Throttle Pedal Position Sensor Switch A Circuit High Throttle Pedal Position Sensor Switch B Circuit Low Throttle Pedal Position Sensor Switch D Circuit Low Throttle Pedal Po
32. e Oil Life Reset Entry Screen 7 Input a valid value and use the function key Finish to confirm Oil Life Reset Figure 4 41 Sample Oil Life Reset Entry Screen 8 Press the function key Yes if the entered value are to be saved or press the function key NO to quit Input Dialog Box 49 Do you want to save and continue Figure 4 42 Sample Input Dialog Box Screen 9 Wait for a few seconds and a screen with Success message comes up once the oil life reset has been done successfully Press any key to continue 27 NT401 Oil Service Tool Manual_English_V1 01 Oil Life Reset Success Figure 4 43 Sample Oil Life Reset Successful Screen NOTE If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 4 2 3 5 Mercedes Benz Operations This section illustrates how to do oil reset on Mercedes Benz gt To do oil reset on Mercedes Benz 1 Scroll up and down arrow keys to select a control unit and press ENTER key to continue Control unit adaptations 1 ASSYST settings Figure 4 44 Sample Control Unit Adaptations Screen 2 Scroll up and down arrow keys to highlight the settings item and press ENTER key to reset the value Settings 1 National version factor 2 Oil quality 3 Distance driven since last oil change 4 Days since last oil change 5 Oil m
33. eeze frame detected the message No freeze frame data stored is displayed Freeze Frame Data E Absolute pressure 0 00 mbar Timing angle 5 5 BTDC E pa N 45 NT401 Oil Service Tool Manual_English_V1 01 Figure 5 19 Sample Freeze Data Screen 3 Press function key Save to store freeze frame information Or use the BACK key to exit 5 6 Read I M Readiness Status Data I M Readiness option allows to view a snapshot of the operations for the emission system on OBDII EOBD vehicles I M Readiness is a useful function used to check if all monitors are OK or N A The vehicle s computer performs tests on the emission system during normal driving conditions After a specific amount of drive time each monitor has specific driving conditions and time required the computer s monitors decide if the vehicles emission system is working correctly When the monitor s status is e OK vehicle was driven enough to complete the monitor e INC Incomplete vehicle was not driven enough to complete the monitor e N A Not Applicable vehicle does not support that monitor There are two types of I M Readiness tests e Since DTCs Cleared shows status of the monitors since the DTCs were last cleared e This Drive Cycle shows status of monitors since the start of the current drive cycle Below is a list of abbreviations and names of OBD II monitors supported by the service tool A C Refrig Mon Air Conditioning Refriger
34. en the user and advertising designer Foxwell Company is not liable for such activities 13 Copyright You acknowledge that any and all of content subsisting in or used in connection with the products the software updates and all documentation are and shall remain the copy right of foxwell and may only be used to perform its obligations under this Agreement and shall not remove any trade mark from the products You shall not during or after the expiry or termination of this Agreement without the prior written consent of Foxwell use or adopt any name trade name trading style or commercial designation that includes or is similar to or may be mistaken for the whole or any part of any trademark trade name trading style or commercial designation used by Foxwell or any third party 14 Law and disputation The terms of network service should accord with relevant law of the People s Republic of China You and Foxwell agree to obey the ruling of the Supreme Court Should there be any contradiction between the some terms of the service and the law of the People s Republic of China the terms should be re explained according to the law and other terms still keep valid Figure 8 3 Sample Terms amp Conditions Screen 4 Create a unique user name and password complete the registration form and then click Submit to create your ID When your ID has been created you are allowed to view all programs associated with your tool download updates edit your pr
35. ent Cluster and will retrieve SRI instructions as well as current values stored in the cluster It will also specify the total length in kilometers and or days between the service intervals In this case it only specifies the time or distance between intervals it does not reset the interval When an inspection has been carried out prematurely before the service interval is required it will read the kilometers or days since the last service set them to the required value gt To do oil service reset on AUDI SEAT SKODA VW vehicles 1 Scroll with up and down arrow keys to highlight Auto Reset from the Oil Reset menu and press ENTER A screen with a list of available service displays 15 NT401 Oil Service Tool Manual_English_V1 01 Oil Reset 1 Manual Reset 2 Auto Reset M Figure 4 10 Sample Oil Reset Menu Screen 2 Scroll with the arrow keys to highlight a function you wish to test and press the ENTER key to confirm Oil Reset 1 SID Maximum value of time to service 2 SID Maximum value of distance to service 3 ESI Max value of time between insp 4 ESI Max value km driving dis insp 5 ESI Minimum value of time between inspections 6 ESI Min value km driving dist insp 7 ESI Distance driven since inspections 8 ESI Time since inspections Figure 4 11 Sample Oil Reset Function Screen 3 The stored value on the vehicle being tested displays Press the function key OK to set the service v
36. erfere with driving controls e Do not exceed voltage limits between inputs specified in this user s manual e Always wear ANSI approved goggles to protect your eyes from propelled objects as well as hot or caustic liquids e Fuel oil vapors hot steam hot toxic exhaust gases acid refrigerant and other debris produced by a malfunction engine can cause serious injury or death Do not use the service tool in areas where explosive vapor may collect such as in below ground pits confined areas or areas that are less than 18 inches 45 cm above the floor e Do not smoke strike a match or cause a spark near the vehicle while testing and keep all sparks heated items and open flames away from the battery and fuel fuel vapors as they are highly flammable e Keep a dry chemical fire extinguisher suitable for gasoline chemical and electrical fires in work area e Always be aware of rotating parts that move at high speed when an engine is running and keep a safe distance from these parts as well as other potentially moving objects to avoid serious injury e Do not touch engine components that get very hot when an engine is running to avoid severe burns e Block drive wheels before testing with engine running Put the transmission in park for automatic transmission or neutral for manual transmission And never leave a running engine unattended e Do not wear jewelry or loose fitting clothing when working on engine 4 NT401 Oil Servi
37. ged Multiple CVNs may be reported for a control module It may take several minutes to do the CVN calculation In use performance tracking tracks performance of key readiness monitors NOTE Available options will vary depending on the vehicle under test To request vehicle information 1 Scroll with the arrow keys to highlight Vehicle Info from Diagnostic Menu and press the ENTER key 52 NT401 Oil Service Tool Manual_English_V1 01 Diagnostic Menu La 6 I M Readiness 7 O2 Monitor Test 8 On board Monitor Test 9 Component Test 10 Vehicle Info 11 Modules Present 12 DTC Lookup 1 System Status Figure 5 34 Sample Diagnostic Menu Screen 2 Follow on screen instruction and send the command to read vehicle information A screen with a list of available options displays Vehicle Info 1 Calibration ID Figure 5 35 Sample Vehicle Info Screen 3 Scroll with the arrow keys to highlight an available option and press the ENTER key A screen with details of the selected option displays Calibration ID Calibration 1K0907115A 0050 Identifications Figure 5 36 Sample Calibration ID Screen 4 Press function key Save to store the readiness data Or use the BACK key to exit and return 5 11 Modules Present The service tool identifies module IDs and communication protocols for OBD2 modules in the vehicle 53 NT401 Oil Service Tool Manual_English_V1 01 P To view module IDs and communic
38. generally goes to the next screen 7 HELP Key displays helpful information 8 Power Switch turns on off the service tool and press and hold for 5 seconds for emergency reboots 9 SD Card Port holds the SD memory card for data backup and software update 8 NT401 Oil Service Tool Manual_English_V1 01 10 USB Port provides a USB connection between the Service tool and PC or laptop IMPORTANT Do not use solvents such as alcohol to clean keypad or display Use a mild nonabrasive detergent and a soft cotton cloth 2 2 Accessory Descriptions This section lists the accessories that go with the service tool If you find any of the following items missing from your package contact your local dealer for assistance 1 User s Guide provides operation instructions for the usage of the service tool 2 USB Cable provides connection between the service tool and a computer to upgrade the tool 3 Memory Card contains the service tool s operating software and applications IMPORTANT Do not remove the memory card unless performing updates to the card 4 Diagnostic Cable provides connection between the service tool and vehicle 5 Nylon Carry Pouch stores the service tool and its accessories 2 3 Technical Specifications Display Backlit 240 320 TFT color display Working Temperature 0 to 60 C 342 to 140F Storage Temperature 20 to 70 C 4 to 158 Power Supply 8 18V powered by vehicle battery Dimensions L W H 200 100 38mm
39. h up and down arrow keys to highlight Auto Reset from the Oil Reset menu and press ENTER to confirm Oil Reset 1 Oil Reset With One Button 2 Manual Reset 3 Auto Reset Mx Figure 4 35 Sample Oil Reset Menu Screen 2 Enter vehicle information by certain VIN characters such as model and year to identify the vehicle being tested and press ENTER key to confirm Model Year 5 012013 2 C0012 4 BO LAO To eT amp 112004 Be Passenger a enor 2 LO Trk MPV Incomplete 1612006 La mi gda Ty 1 Ghevoet Figure 4 36 Sample Vehicle Identification Screens 3 Select the control module and press ENTER key to communicate with the vehicle 25 NT401 Oil Service Tool Manual_English_V1 01 election 1 Engine Control Module 2 Transmission Control Module Figure 4 37 Sample Control Module Selection Screen 4 Once the tool established communication with the vehicle the Oil Reset screen comes up Press the ENTER key to confirm Oil Reset 1 Oil Life Reset Figure 4 38 Sample Oil Reset Menu Screen 5 Press the function key OK to continue or press the function key Cancel to quit Oil life Reset Engine Oil Life 49 Figure 4 39 Sample Oil Life Reset Screen 6 If the value needs to be changed press the function key Keyboard The screen for new value entry displays 26 NT401 Oil Service Tool Manual_English_V1 01 Oil Life Reset Input the value must be between 0 and 100 Figure 4 40 Sampl
40. his Drive Cycle Malfunction Indicator lamp MIL Status OFF Misfire Monitoring Fuel system Monitoring lok OK Comprehensive component Monitoring OK H Catalyst Monitoring Heated Catalyst Monitoring INC a _M E o E Evaporative system Monitoring Heated Caianst Monona IN Secondary air system Monitoring N A Figure 5 22 Sample IM readiness screen 2 3 Press the BACK key to exit 47 NT401 Oil Service Tool Manual_English_V1 01 5 7 O2 Monitor Test OBD II regulations require certain vehicles monitor and test oxygen O2 sensors to isolate fuel and emissions related faults The O2 Monitor Test function is used to retrieve completed O2 sensors monitor test results The O2 Monitor Test is not an on demand test O2 sensors are not tested when selected via the menu but tested when engine operating conditions are within specified limits If the vehicle uses a controller area network CAN protocol to communicate this function is not supported by vehicle Refer to On Board Monitor Tests on page 38 39 for O2 monitor data of CAN equipped vehicles To retrieve O2 monitor data 1 Scroll with the arrow keys to highlight O2 Monitor Test from Diagnostic Menu and press the ENTER key A screen with a list of available sensors displays Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 02 Monitor Test 8 On board Monitor Test Figure 5 23
41. ic Menu and press the ENTER key 49 NT401 Oil Service Tool Manual_English_V1 01 Diagnostic Menu ie 1 System Status a gt 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 O2 Monitor Test 8 On board Monitor Test ho Figure 5 27 Sample Diagnostic Menu Screen 2 Depending on the protocol the vehicle used one of these 2 screens shows On Board Monitor Test 1 Test 01 Data 2 Test 02 Data 3 Test 05 Data 4 Test 06 Data Figure 5 28 Sample Non CAN Vehicle Test Screen On Board Monitor 1 02 Monitor B1S1 2 02 Monitor B1S2 3 Catalyst Monitor B1 4 EGR Monitor Bank1 Figure 5 29 Sample CAN vehicle test screen 3 Scroll with the arrow keys to highlight a test group and press the ENTER key to confirm A screen with details of the selected sensor displays Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data For non CAN vehicles test screen is illustrated as below 50 NT401 Oil Service Tool Manual_English_V1 01 Test 01 Data Test Value Min Limit Max Limit Status Figure 5 30 Sample Non CAN vehicle test screen For CAN vehicles test screen is illustrated as below Test 01 Data 0 450 OK ES Figure 5 31 Sample Can vehicle test screen 4 Press the BACK key to exit and return 5 9 Component Test Component Test allows the service tool to con
42. icating 1 Make sure the ignition is switched on 2 Check the cables between the Tester and the vehicle DLC 3 Check that the vehicle battery is charged Figure 4 6 Sample Oil Reset With One Button Failed Screen 4 2 2 Manual Reset Almost all Asian vehicles and most American and European vehicles have mechanical oil service indicator reset The service tool does not have to communicate with the vehicle being tested but guides you to complete the service manually by providing step by step on screen instructions When Manual Reset is selected and the vehicle being tested identified a procedure opens on the screen Scroll with arrow keys to read the entire procedure and performing the necessary steps as directed by the on screen instructions The exact order of the test operation steps may vary depending on the test vehicle Be sure to follow all on screen instructions This manual reset procedure can be interrupted and aborted if the ignition key position is changed gt To do oil reset manually 1 Scroll with up and down arrow keys to highlight Manual Reset from the Oil Reset menu and press ENTER to confirm Oil Reset 1 Oil Reset With One Button 2 Manual Reset 3 Auto Reset Figure 4 7 Sample Oil Reset Menu Screen 2 Enter vehicle information by certain VIN characters such as model and year to identify the vehicle being tested and press ENTER key to confirm 14 NT401 Oil Service Tool Manual_English_V1 01 BUICK j
43. inimum warning 28 NT401 Oil Service Tool Manual_English_V1 01 Figure 4 45 Sample Oil Reset Setting Menu Screen 3 Press the function key Modify to enter the new value ASSYST settings Distance driven since last oil change 5212 National version factor Days since last oil change 1326 E mm Figure 4 46 Sample ASSYST Setting Screen 4 Follow on screen instruction and then you can enter a new value by pressing the function key Keyboard Distance driven since last o 5212 The value can be set between O and 200000 Figure 4 47 Sample Service Mileage Entry Screen 5 Scroll with the arrow keys to highlight your desired letter or number and press the ENTER key to confirm To delete a letter or number use the function key Previous to move the cursor to it and then press the Backspace button When finished the entry press Finish key to continue Distance driven since last o Figure 4 48 Sample Service Mileage Entry Keyboard Screen 29 NT401 Oil Service Tool Manual_English_V1 01 6 Press the function key YES to save and continue the oil light reset or press the function key NO to quit the oil light reset Input Dialog Box 5219 Do you want to save and continue Figure 4 49 Sample Service Mileage Reset Confirmation Dialog Box Screen 7 A screen with Success message comes up once the oil light reset has been done successfully Information Success Figure 4 50 Sample Service Mileage Reset Succe
44. ion Sensor Switch D Circuit Low Throttle Pedal Position Sensor Switch E Circuit Low High Speed CAN Communication Bus Mass or Volume Air Flow A Circuit Figure 6 3 Sample Test Data Details Screen 56 NT401 Oil Service Tool Manual_English_V1 01 4 If you are reviewing live data or freeze frame data use the function key Next Frame or Pre Frame to scroll through all possible frames when necessary 1 of 4 Frame Numbers of DTCs Fuel system 1 status a Fuel System 2 status pr Calculated Load Value Engine Coolant Temperature Short Term Fuel Trim Bank 1 Figure 6 4 Sample Test Data Details Screen 5 To erase a record scroll with the arrow keys to highlight it and press the function key Delete To delete all records press the function key Delete All Answer Yes to delete and No to quit 7 System Setup This section illustrates how to program the service tool to meet your specific needs When Setup application is selected a menu with available service options displays Menu options typically include e Language e Unit e Beep Set e Key Test e LCD Test e About e Shortcuts 7 1 Select Language Selecting Language opens a screen that allows you to choose system language The service tool is set to display English menus by default P To configure system language 1 Scroll with the arrow keys to highlight Language from Setup menu and press the ENTER key Application Setup 7 Language i Key Test Lcd Test About Sh
45. ish_V1 01 5 Input a valid value and use the function key Finish to confirm Spark plugs Kj Ss Figure 4 27 Sample Spark Plugs Enter Screen 6 Press the function key Yes to if the new value is to be saved or press the function key NO to quit Input Dialog Box 95 Do you want to save and continue Figure 4 28 Sample Input Dialog Box Screen 7 A screen with success message displays and the new value is set Spark plugs Success Figure 4 29 Sample Spark Plugs Reset Successful Screen NOTE If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 22 NT401 Oil Service Tool Manual_English_V1 01 20PIN Connector To perform oil service functions on vehicles with a 20PIN connector 1 Scroll with up and down arrow keys to select the function from the menu and press ENTER key to confirm BMW 1 Oil service 2 Inspection Figure 4 30 Sample Oil Reset Function Menu Screen 2 Ascreen with Reset Implemented message displays once the oil service reset has been done successfully Reset Implemented Figure 4 31 Sample Oil Service Reset Successful Screen NOTE If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact y
46. l level sensor defective Engine control unit not encoded Figure 4 22 Sample Engine Oil Reset Failed Screen NOTE Not all failure screens are the same The message may vary by the service being performed CBS Correction P To perform oil service functions on BMW with OBDII connector 1 Scroll with up and down arrow keys to select the CBS Correction function and press ENTER key to confirm Oil Reset 1 CBS reset 2 CBS correction Figure 4 23 Sample Oil Reset Menu Screen 20 NT401 Oil Service Tool Manual_English_V1 01 2 Ascreen with a list of available tests displays as below CBS Correction 1 Engine Oil 2 Spark plugs 3 Front brakes 4 Rear brakes 5 Coolant 6 Diesel particle filter 7 Brake fluid 8 Microfilter Figure 4 24 Sample CBS Correction Menu Screen NOTE Not all functions listed above are applicable to all vehicles Available options may vary by the year and model of the test vehicle 3 Scroll with up and down arrow keys to highlight a function from the menu and press the ENTER key to confirm Spark plugs Availability 100 Service counter 0 Figure 4 25 Sample Spark Plugs Test Screen 4 If the value needs to be changed press the function key Modify The screen for new value entry displays as below Spark plugs 100 j Enter the new value for spark plugs in Figure 4 26 Sample New Spark Plug Value Entry Screen 21 NT401 Oil Service Tool Manual_Engl
47. load and update When download completed the downloaded programs start to update automatically DWIZ DL PALETA Lard La beans bist aL WAS En En ii En m Em ER m m En ih in En m Upalating Pee W RAPE BENZ VADE oo io EN Figure 8 12 Sample Software Downloading and Updating Screen 8 An Update Complete message displays once the updates completed 69 NT401 Oil Service Tool Manual_English_V1 01 a p reri y it MY UPDATES Updates Installed Softwares em 5 airar e rman lap Feed ae Fiene A 05 00 Eu 05 03 7014 Updated Vt En 15 02 5014 Updated 100 1640 PLAVIACK Di Iama fi Updo Compleza n l y EN PEIEE Wodeed i o En O5 03 D514 Vodated A AAA i EN 102 2014 Updarad ME avsi En 15 02 2014 A i ii PENETAN Undated EA 5 10 EN Updated ST 7 En Woditod A o 15 m Updated ita ERAN 45 10 En JAH Vodared EP En 19 03 5014 Undated I 55 L EN 19 03 7014 Updated Serial Number ADLIO7000037 vpis proi 20 Tumm ea Co Lid AR da arsa Figure 8 13 Sample Update Complete Screen NOTE If Update Failed dialog comes up it indicates that the software updates failed Please check the network connection or SD card If the problem still exists please contact with your local dealer for assistance 9 To view installed items click the Installed Software tab 10 To uninstall a software or all software select them and click the Uninstall button A
48. ments e Operation System Win98 NT Win ME Win2000 Win XP VISTA and Windows 7 e CPU Intel PIII or better e RAM 64MB or better e Hard Disk Space 30MB or better e Display 800 600 pixel 16 byte true color display or better e Internet Explorer 4 0 or newer NOTE Before updating please make sure your network works correctly and the SD card has been identified 1 Download the update tool DiagMate from our site www foxwelltech com by selecting Support gt updates gt Professional Scanner and save the application in computer disk 2 Unzip the update tool file Follow instructions on computer screen to install the tool and driver z 3 Double click the desktop icon Foxscanner to launch the application 4 Remove the memory card from the scanner put it into the card reader and plug the reader into the computer 5 Login with your Foxwell ID and password FOXWELL Scan Tools For Every Need A UserName efifoxwelltech com Q Password tkkkrrrz Foral pow pascua Stay signed in icher of pus ra t na raned compo pic ii Coprighi 02013 Fossat Tncmelogy Co id Ar n mirta Figure 8 10 Sample Software Update Sign In Screen 6 Click My Updates and all updates applicable to your scanner displays 68 NT401 Oil Service Tool Manual_English_V1 01 Figure 8 11 Sample Home Screen 7 Click the check box es in front of the software s you wish to update and then click the Update button to down
49. nd the uninstalled items can be found in the Updates screen Foxwell Technology E MY UPDATES Updates Installed Softwares hem Sofware Version Release Daca chon ACL vsi 20002013 ALFA VES AE Ur atal aunt 13 00 Sanger anat BENTLEY 45 00 30 08 2003 ininstsl BENZ v5 00 200 2013 Uninsal Ei VEIG 04 13 3003 Uninstal BUGATTT VES Tay REI Utinwtall OSU 13 09 200 2013 aT CITROEN 13 00 Ea 2003 instal Dacia VEO Ee ERa Uninsial DANDO 15 00 JOA POS Uninstall Ea VII PETET TE Liertatal Eu_FORD 15 09 EPE Unnstal DisgMaie 41 09 Figure 8 14 Sample Uninstall Software Screen 70 NT401 Oil Service Tool Manual_English_V1 01
50. ng contact your local FOXWELL distributor or visit our website www foxwelltech com to get further information b The customer shall include a return address daytime phone number and or fax number complete description of the problem and original invoice specifying date of purchase and serial number c The customer will be billed for any parts or labor charges not covered by this limited warranty d FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product If FOXWELL cannot perform repairs covered under this limited warranty within 30 days or after a reasonable number of attempts to repair the same defect FOXWELL at its option will provide a replacement product or refund the purchase price of the product less a reasonable amount for usage e If the product is returned during the limited warranty period but the problem with the product is not covered under the terms and conditions of this limited warranty the customer will be notified and given an estimate of the charges the customer must pay to have the product repaired with all shipping charges billed to the customer If the estimate is refused the product will be returned freight collect If the product is returned after the expiration of the limited warranty period FOXWELL normal service policies shall apply and the customer will be responsible for all shipping charges 5 ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
51. ofile leave us feedbacks and join our community to share your ideas and your stories about our products 64 NT401 Oil Service Tool Manual_English_V1 01 Business Type Full Service Gasoline Station gt Other Where Purchased Auto Parts Store z Other Why did you buy this product Other fo How did you learn about this product Other f Business Type Full Service Gasoline Station y Other Where Purchased Auto Parts Store y Other Why did you buy this product other oe ie favorite automotive rap a Other OS Do you have any other automotive diagnostic scanner YES NO fyes please state Would you like to receive product information via email YES NO Would you like to be notified of your product updates and enhancement YES NO Would you like to receive a catalog YES NO Comment Dem Eara Figure 8 4 Sample Registration Form Filling Screen 5 A Submit OK message will comes up if it is registered successfully 65 NT401 Oil Service Tool Manual_English_V1 01 FOXWELL ison C Home Products Support Register Products Become Our Distributor About Us Contact Us wee foxvelltech com says Submit OK Figure 8 5 Sample Succeed Registration Screen 6 If you forget your register ID or password just click Sign in link at the top right of the website then click Forgot your user ID and or password link to input product s serial number and registered email address The New password will comes up once yo
52. ool also receives power through the USB port when it is connected to a PC for updating software and transferring saved files To connect to PC 1 Insert the small end of the USB cable to the USB port at the right side of the scanner and the large end to a computer 2 Press the power switch of the service tool to power it on 3 2 Application Overview When the service tool boots up the Home screen opens This screen shows all applications loaded on the unit Following applications are preloaded into the service tool e OBDII EOBD leads to OBDII screens for all 9 generic OBD system tests e Oil Reset leads to screens for resetting oil service light oil inspection light service mileage service intervals and more on 32 vehicle makes sold worldwide e Setup leads to screens for adjusting default settings to meet your own preference and view information about the scanner e Playback leads to screens for access saved data files 3 3 Input Dialog Box gt This section illustrates how to use the service tool to input letters and numbers such as channel number test values service intervials oil life values service mileage and DTC number Typically you may be required to input letters or numbers when you are doing any of the following operations e Input channel number e look up DTCs e service intervals e oil life values e service mileage The service tool provides 3 different types of keyboard to meet your
53. ortcuts 11D 57 NT401 Oil Service Tool Manual_English_V1 01 Figure 7 1 Sample Setup Screen 2 Press the LEFT RIGHT arrow key select a language and press the ENTER key to confirm Press the Back key to exit and return Application Language English ry espa ol Figure 7 2 Sample Language Selection Screen 7 2 Change Units Selecting Unit opens a dialog box that allows you to choose between US customary or metric units of measure gt To change the unit setup 1 Scroll with the arrow keys to highlight Units from Setup menu and press the ENTER key Application Setup pz Language Unit Beep Key Test Lcd Test a amp About Shortcuts Figure 7 3 Sample Setup Screen 2 Press the LEFT RIGHT arrow key select an item and press the ENTER key to save and return Application Setup Language wf English L Metric Shortcuts 58 NT401 Oil Service Tool Manual_English_V1 01 Figure 7 4 Sample Language Selection Screen 7 3 Configure Beeper Selecting Beep Set opens a dialog box that allows you to turn on off the beeper gt To turn on off the beeper 1 Scroll with the arrow keys to highlight Beep Set from Setup menu and press the ENTER key Application Setup TS GS 824 eT f A Language Unit Key Test Lcd Test Shortcuts Figure 7 5 Sample Setup Screen 2 Press the LEFT RIGHT arrow key select an item and press the ENTER key to save and return Application Setup a3 16 pun L
54. our local dealer for assistant 4 2 3 3 Fiat Operations This section illustrates how to do oil service reset automatically on Fiat vehicles gt To perform the oil service on Fiat 1 Scroll with up and down arrow keys to highlight an option and press ENTER key to confirm 23 NT401 Oil Service Tool Manual_English_V1 01 Oil Reset 1 Servicing information delete 2 Oil change servicing information delete Figure 4 32 Sample Oil Reset Menu Screen 2 Press the function key OK to perform the service or press Cancel to quit Oil change servicing The kilometre value when the service coupon was carried out is stored This procedure is to be done every time coupon servicing is performed Figure 4 33 Sample Oil Change Servicing Screen 3 Follow on screen instructions and send a command to reset oil service A screen with a Test Performed message comes up once the oil change has been done successfully Press any key to return Oil chance servicing Test Performed Figure 4 34 Sample Test Performed Screen NOTE If a No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 24 NT401 Oil Service Tool Manual_English_V1 01 4 2 3 4 GM Operations This section illustrates how to do oil reset by auto reset on GM gt To perform Auto Reset on GM 1 Scroll wit
55. rd pee Name Address City State Province Country Zipcode Phone 86 755 26697229 Fax 86 755 26897226 Email friendivivan 183 com Figure 8 8 Sample Registration Screen 7 Sign in with your Foxwell ID and click My Products gt New Registration option if you have more than one scan tool to be registered And repeat the process as necessary FOXWELL amp alice lee foxwelltech com Logout en Home Products Support Register Products Become Our Distributor MS Contact Us Registered Product New Registration My Profile Feedbacks Community Part No NT611 z Serial No Register Password Submit Reset E Cancel Figure 8 9 Sample New Registration Screen 8 2 Update the Scanner To update your scanner you need following tools e the scan tool e update tool DiagMate 67 NT401 Oil Service Tool Manual_English_V1 01 e PC or laptop with USB ports and Internet explorer e Internet service e SD card reader NOTE The updates are installed in the SD cards Please make sure that SD card is corrected connected to the computer before upgrading The SD card can be inserted into the laptop directly without SD card reader if there s SD card slot on your laptop The USB Port on the scanner is for data reviewing when it connects with a PC laptop To be able to use update tool PC or laptop must meet the following minimum require
56. row keys to highlight About from Setup menu and press the ENTER key Application Setup q T q A Language Unit Key Test Lcd Test a amp About Shortcuts DIR Figure 7 10 Sample Setup screen 2 A screen with detailed information of the service tool displays FOXWELL Product Serial Number AD1307000022 Register Password 000105 Copyright C 2012 Foxwell Technology Co Ltd All rights reserved Figure 7 11 Sample Tool Information Screen 3 Press the Back key to exit and return to the Setup menu 7 7 Configure Shortcut Keys Selecting Shortcuts option lets you to change the functionality of the shortcut buttons b gt To assign a function to a shortcut button 1 Scroll with the arrow keys to highlight Shortcuts from Setup menu and press the ENTER key A screen with available shortcut keys displays 61 NT401 Oil Service Tool Manual_English_V1 01 Application Setup gt y O A g Language Unit Key Test Lcd Test A About Shortcuts 11D Figure 7 12 Sample Setup screen 2 Press the UP DOWN arrow key select an shortcut key and press the ENTER key A screen with a list of loaded applications displays ShortCuts 1 Edit ShortCuts F1 Function 2 Edit ShortCuts F2 Function 3 Edit ShortCuts F3 Function Figure 7 13 Sample Shortcuts Screen 3 Scroll with the UP DOWN arrow keys to highlight an application and press the ENTER key to assign the application to the shortcut key 4 Press
57. s a situation which if not avoided may result in damage to the test equipment or vehicle Example IMPORTANT Do not soak keypad as water might find its way into the scanner 7 NT401 Oil Service Tool Manual_English_V1 01 2 Introduction 2 1 Oil changes are the 1 service your shop will perform each year Enhance your service with the latest NT401 Oil Light Reset Tool from Foxwell and eliminate the need to take the vehicle to the dealer or use an OEM service tool to reset oil service lights With the tool properly connected to the vehicle s data link connector DLC you can use the service tool to reset oil service light oil inspection light service mileage service intervals and more on 32 vehicles Scanner Descriptions This section illustrates external features ports and connectors of the service tool 1 FOXWELL 10 2 9 j E E E 5 Enter NS Back 6 4 7 8 Figure 2 1 Front View 1 Diagnostic Port provides connection between the service tool and vehicle 2 LCD Display shows menus test results and operation tips 3 Function Keys Shortcut keys three keys that correspond with buttons on some screens for executing special commands or provide quick access to most frequently used applications or functions 4 Direction Keys select an option or scroll through a screen of data or text 5 BACK Key exits a screen and generally returns to previous screen 6 ENTER Key executes a selected option and
58. sition Sensor Switch E Circuit Low High Speed CAN Communication Bus Mass or Volume Air Flow A Circuit Figure 5 6 Sample Code screen 4 Press function key Save to store DTC information Or use the BACK key to exit 40 NT401 Oil Service Tool Manual_English_V1 01 5 3 Erase Codes Erase Codes menu lets you to clear all current and stored DTCs from the control module Also it erases all temporary ECU information including freeze frame So make sure that the selected system are completely checked and serviced by technicians and no vital information will be lost before clearing codes NOTE e To clear codes make sure that the ignition key is switched to ON with the engine off e Erase Codes does not fix the problem that caused the fault DTCs should only be erased after correcting the condition s that caused them To clear codes 1 Scroll with the arrow keys to highlight Erase Codes from Diagnostic Menu and press the ENTER key 1 2 3 4 5 6 7 8 Diagnostic Menu System Status Read Codes Erase Codes Live Data Freeze Frame I M Readiness O2 Monitor Test On board Monitor Test Figure 5 7 Sample Diagnostic Menu Screen 2 Follow the on screen instructions and answer questions about the vehicle being tested to complete the procedure Erase Codes DTC and Freeze Data will be lost Do you wish to continue Figure 5 8 Sample Erase Codes Screen 3 Check the codes again If any codes remain repeat the Erase
59. ssful Screen NOTE If No communicating message comes up it indicates the oil reset failed Please follow on screen instructions to troubleshoot it If the problem still exists please contact your local dealer for assistant 4 2 3 6 Land Rover Operations This section illustrates how to do oil reset on Land Rover gt To do oil reset on Land Rover 1 Scroll with up and down arrow keys to highlight Auto Reset from the Oil Reset menu and press ENTER key 30 NT401 Oil Service Tool Manual_English_V1 01 Oil Reset 1 Manual Reset 2 Auto Reset E Figure 4 51 Sample Oil Reset Menu Screen 2 Select the vehicle being tested and press the ENTER key to confirm 1 Discovery 2 Range Rover 3 Range Rover Sport 4 Freelander 2 LR2 Figure 4 52 Sample Vehicle Selection Screen 3 Set the ignition switch to on and press the function key OK to continue or press Cancel to quit Freelander 2 LR2 Set the ignition switch to on position 2 Figure 4 53 Sample Oil Reset Instruction Screen 4 Turn key on with engine off and press the function key OK to continue or press Cancel key to quit oil light reset 31 NT401 Oil Service Tool Manual_English_V1 01 Freelander 2 LR2 Key on engine off Figure 4 54 Sample Oil Reset Instruction Screen 5 Set the ignition switch to off and press the function key OK to continue or press Cancel key to quit the oil light reset Freelander 2 LR2 Set the ignition switch
60. trol operation of vehicle components tests or systems NOTE e Some manufacturers do not allow tools to control vehicle systems e The manufacturer sets the criteria to automatically stop test Refer to appropriate vehicle service manual before using this function P To perform a component test 1 Scroll with the arrow keys to highlight Component Test from Diagnostic Menu and press the ENTER key A screen with a list of available tests displays 51 NT401 Oil Service Tool Manual_English_V1 01 Diagnostic Menu I M Readiness 7 02 Monitor Test 8 On board Monitor Test 9 Component Test 10 Vehicle Info 11 Modules Present 12 DTC Lookup System Status Figure 5 32 Sample Diagnostic Menu Screen 2 Scroll with the arrow keys to highlight a system or component press the ENTER key to start test and the service tool displays the message Command Sent Component Tes 1 EVAP Sys Leak test Figure 5 33 Sample Component test screen 3 Press the BACK key to exit and return 5 10 Request Vehicle Information gt Vehicle Information allows to request the vehicle s VIN number calibration ID s which identifies software version in vehicle control module s calibration verification numbers CVN s and in use performance tracking on model year 2000 and newer OBD II compliant vehicles CVNs are calculated values required by OBD II regulations They are reported to check if emission related calibrations have been chan
61. u click Submit button If you want to change password please sign in with your user name and password then select My Profile Password Change to create a new password FOXWELL dapin Welcome to Foxwell FOXWELL aon EN Sign ms an exiting Decor Usar Hare PRERAGrO Forget your Password ISi signed in LEen A ya r on a H Enter a valid secial number and ihe registered Emai adress to retrieve your passeond Senal NO 1541339000008 Email Pa a Figure 8 6 Sample User ID and or Password Reset Screen www foxwelltech com says Dear alice lee foxwelltech com your new password is Please log in your account with this password and reset your own password immediately Or copy and keep this password in a safe place for future use OK j Figure 8 7 Sample Password Reset Successful Screen 66 NT401 Oil Service Tool Manual_English_V1 01 NOTE If the user name is different from the email you filled when registration please input registered email rather than your user name to retrieve your password product information get updates for your scan tool leave us feedbacks get our professional technical supports and share your successful story with other users If you already have a Foxwell account click here to Sign in if you are new to Foxwell simply complete the forms below to create an account and register your product s Password l e Confirm Passwo

NT401 user manual english free

Contents

Download Pdf Manuals

Related Search

Related Contents