Home

Quick Start Guide

image

Contents

1. SMa SMDa SMQa RM U S Patent 7 225 135 Serial Number Purchase Date uick Start Guide ISS yup Ar TORN on f ROSONI HOLD AT TURN ON EMOTE HOLD AT TURN z FREQ Quick STANDBY RF OFF POWER RF ON HOLO AUDIO SMa 10 20 me This guide is intended to assist with initial setup and operation of your Lectrosonics product For a detailed user manual down load the most current version at 24jul07 Controls and Functions LCD Screen Battery Compartment Cover Plate UP Arrow Antenna Battery NICS qoipartuRn y Compartment Opener th SMa POWER RF ON HOLD LOCK 100 ye DOWN Arrow Modulation AUDIO FREQ 4 n n A he O LEDs PWR auick il SANDBY RF OFF Audio AN Input Jack Power LED AUDIO Button FREQ Button Tuning LCD Screen Used to display the status of the selected function Power LED Indicates power status and battery strength Audio Input Jack Accommodates most lavaliere and dynamic microphones and line level signals Modulation LEDs Provides a visual indication of the audio input signal level either red or green to indicate modulation levels Audio Button Used to display the audio level setting 0 dB to 44 dB on the LCD and used with the Up and Down arrows to adjust the audio level input from the micro phone FREQ Button Used to set the operating frequency and toggle the LCD between the operating frequenc
2. ers contact the factory for details Compatibility Mode Note RF transmission is prevented while selecting Compatibility Modes Also the SM exits the Compatibility Mode screen to Standby Mode See Standby Mode this section Note The unit comes from the factory configured as a 400 Series transmitter 1 Set the receivers audio controls to minimum 2 Power up the SM and observe the Boot Sequence If the Compatibility Mode for the SM does not match the corresponding receiver then power off the SM transmitter 3 From a power off condition press and hold the Up arrow then press the AUDIO and FREQ buttons simultaneously 4 TheLCD will display the current Compatibility Mode Use the Up or Down arrow buttons to set the Compatibility Mode to match the corresponding receiver W www lectrosonics com The following Compatibility Modes are selectable e 100 Series mode CP 100 e 200 Series mode CP 200 e Mode 3 Contact factory for details CP 3 e 400 Series mode CP 400 e IFB Series mode CP IFB e Mode 6 Contact factory for details CP 6 5 The Compatibility Mode selected in Step 4 will be the current Compatibil ity Mode until reset using this procedure Pressing AUDIO or FREQ exits into the Standby Mode To power off from the compatibility mode screen press AUDIO and FREQ together Setting Transmitter Operating Frequency The Operating Frequency of the SM is displayed either in MHz or as a two digit hexa
3. This gain adjustment matches the Less than 20 dB Oof Ooft transmitter gain with the microphone s 20 dB to 10 dB Green Oof output level the user s voice level and the 10 dB to 0 dB Green __ Green _microphone s position The audio input 0 dB to 10 dB Red creen level can be set with the unit in Standby Greater than 10dB Red Red Mode or powered up for normal operation 1 2 3 4 5 Locking or Unlocking the Control Panel The Lock mode protects the transmitter from accidental changes to its settings 1 2 www lectrosonics com Note Different voices will usually require different settings of the AUDIO control so check this adjustment for each person using the system If several different people will be using the transmitter and there is not time to make the adjustment for each individual adjust it for the loudest voice With the SM powered off insert the microphone plug into the Audio Input Jack aligning the pins and ensuring that the connector locks Place the SM in Standby Mode or if the unit is to be powered up and ad justed mute the main sound system prior to powering up the transmitter Position the microphone in the location where it will be used in actual operation Observe the SM audio level LEDs while speaking or singing into the microphone at the same voice level that will be used during the program While holding the AUDIO button press the Up or Down arrow buttons until t
4. using block independent hex code 2 b select a block number optional uncovers page 3 3 000 000 set transmitter s frequency in MHz avail if a block is selected www lectrosonics com zZ LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer This warranty does not cover equipment which has been abused or damaged by careless handling or shipping This warranty does not apply to used or demonstrator equipment Should any defect develop Lectrosonics Inc will at our option repair or replace any defective parts without charge for either parts or labor If Lectrosonics Inc cannot correct the defect in your equipment it will be replaced at no charge with a similar new item Lectrosonics Inc will pay for the cost of returning your equipment to you This warranty applies only to items returned to Lectrosonics Inc or an authorized dealer shipping costs prepaid within one year from the date of purchase This Limited Warranty is governed by the laws of the State of New Mexico It states the entire liablility of Lectrosonics Inc and the entire remedy of the purchaser for any breach of warranty as outlined above NEITHER LECTROSONICS INC NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT SPECIAL PUNITIVE CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING
5. FREQ Battery Level AC 4 LOU FREQ Button tery Level ii The RM gives you remote control of SM Series transmitters using an audible tone delivered to the transmitters microphone When the SEND button is pressed a dweedle tone will play from the RM speaker and the parameter on the transmitter will be set immediately The transmitter must be configured to accept commands from the RM see page 6 Adjustments can be made to set e Audio input gain Note The speaker should be uncovered and e Frequency held within a few inches of the transmitter s microphone The longest usable range is about 6 feet depending on the microphone e Sleep mode ON OFF and volume settings e Lock or Unlock modes In the power saving sleep mode power consumption drops to 20 of normal Powering the RM On and Off Press the AUDIO and FREQ buttons together briefly Principles of Operation The RM user interface is organized into pages which are accessible via the AUDIO and FREQ buttons Once on a page settings can be adjusted with the UP and DOWN arrow buttons Only the specific function displayed is altered The AUDIO button cycles through 4 pages 1 Aud set transmitter s audio level 2 SLEEP unSLP cause transmitter to sleep or wake up 3 Loc unLoc lock or unlock transmitter s buttons 4 Loud adjust RM speaker volume press SEND button for a sample tone The FREQ button cycles through 3 pages 1 CH set transmitter s channel
6. OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS INC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS INC EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT This warranty gives you specific legal rights You may have additional legal rights which vary from state to state LECTROSONICS ie Made in the USA by a Bunch of Fanatics 581 Laser Road NE e Rio Rancho NM 87124 USA e www lectrosonics com 505 892 4501 800 821 1121 fax 505 892 6243 sales lectrosonics com
7. decimal num ber Pressing the FREQ button toggles between the Frequency displayed two display modes The frequency can be set with in MHz the unit in Standby Mode or while powered up for normal operation Note You must first find a clear frequency P z F l with the receiver then set the transmitter to d ha dema match number To change the Operating Frequency of the SM Series transmitter 1 Press the FREQ button to enter this screen Note The default display is in MHz Pressing the FREQ button again displays the operating frequency as a two digit hexadecimal number 2 While holding the FREQ button use the Up or Down arrow buttons to move the operating frequency up or down in 100 kHz increments from the current setting Holding the Up or Down arrows will cause rapid scrolling through the frequencies Note The operating frequency displayed on the LCD wraps as it reaches the upper or lower end of its range Thus if you intend to move the operating frequency from the lower end of the range to the upper end it may be faster to do this by using the Down arrow until the frequency wraps to the upper end 4 LECTROSONICS INC Attaching a Microphone and Adjusting Gain The front panel Modulation LEDs indicate limiter activity See chart below Once set the transmitter s audio level setting should not be used to control the volume of your sound system or recorder Signal Level 20 LED oLed levels
8. he both the 20 and 10 LEDs glow green with the 10 LED occa sionally flickering red 0 dB to 10 dB range during peaks Note Setting the audio level too high reduces the dynamic range of the audio signal Setting the audio level too low may cause hiss and noise in the audio If the unit was set up in Standby Mode it will be necessary to power up the SM and adjust the remaining components of the audio system prior to use Ensure the SM setup is complete Simultaneously press both the Up and Down boc arrow buttons to start the Lock timer When the timer reaches zero Loc is displayed and the controls are locked Important The only ways to unlock a locked transmitter are to remove the battery or unlock it via the remote control It cannot be unlocked or powered off using the buttons The remote control will work only if the transmitter was previously configured to respond to the remote control The unit will always power up in unlocked mode Ol Battery Installation The SM transmitter is powered by a single AA 1 5 volt battery while the SMD and SMQ use two AA batteries We recommend using lithium or high capac ity rechargeable batteries for longest life In the SM lithium batteries provide over 4 5 hours of operation at room temperature Note Standard zinc carbon batteries marked heavy duty or long lasting are not adequate The battery status circuitry is designed for the voltage dro
9. p over the life of lithium batteries To install new batteries 1 2 3 Configuring for Remote Control Use Turn the Battery Cover Plate Opener counterclockwise open the battery compartment and remove any old batteries Insert the new battery or batteries into the housing The positive battery terminal goes into the transmitter first Replace the Bat tery Cover Plate and tighten the Opener Some transmitter settings can be changed with the rc on Lectrosonics RM Remote Control However you must first configure the SM Series transmitter to accept commands from the RM Press and hold the Down Arrow Button then ee Sale 1 power on the transmitter by pressing the Remote Control Screens Audio and Freq buttons simultaneously 2 The LCD will display the status either rc ON or rc OFF To change the setting press the Up or Down arrow button 3 Power Off the transmitter by pressing the Audio and Freq buttons simulta neously The RC setting will persist when you Power Up the transmitter again Note SM Series transmitters with firmware version 1 6 and later are factory set to rc ON by default 6 LECTROSONICS INC RM Remote Control Operating Instructions LCD Display UP Arrow Button Battery Cover SEND Knob CTROSONICS Button Lanyard Attachment DOWN Arrow i a 2 SLEEP BLOCK ae Button AUDIO Button O O E ne FREQ Gg m Speaker BTO gt Lock ee
10. y in MHz and a two digit hexadecimal frequency code Up Down Arrows Used to adjust the selected function or parameter Battery Compartment Cover Plate and Opener Used to install or remove battery batteries LECTROSONICS INC Operating Instructions Power On 1 Ensure that good batteries are installed 2 Simultaneously press and hold the AUDIO and Initial Power On FREQ buttons until the Power On Boot Se Timer Screen quence is initiated 3 seconds Power Off 1 Simultaneously press and hold the AUDIO and OFF 3 FREQ buttons while observing that the word Off appears in the LCD along with a counter Initial Power Off Timer Screen 2 When the counter reaches 0 the unit turns off Note If the AUDIO and FREQ buttons are released before the end of the countdown the unit will not turn off Standby Mode From the OFF position quickly press and release both the AUDIO and FREQ buttons simultaneously to enter and exit this mode Allows the user to verify Standby Screen or change the transmitter s operating frequency or audio input level without transmitting any signals Selecting the Compatibility Mode SM Series transmitters will work with all Digital Hy brid Wireless receivers in the native compandor less mode They are also capable of working with 200 Series 100 Series and IFB analog receivers 400 Series or Digital plus some other brands of analog wireless receiv Hybrid Wireless

Download Pdf Manuals

image

Related Search

Related Contents

Descargar  CH-‐3000 - SunStar  18-00073A 取扱説明書のダウンロードはこちら DOWN  olla arrocera estimado cliente advertencias de seguridad  SUR LES SOLUTIONS CONSIDERABLEMENT  Manual de Instruções de Consulta à AMEDINAL  

Copyright © All rights reserved.
Failed to retrieve file