Quick Start E7 Operations Manual
Contents
1. QUICK START USERS GUIDE lf you do not understand any part of this quick start users manual and would like the complete version Please visit our web site www encoreautomotivesystems com The complete manual is necessary for advanced users and not all user functions are covered in this quick start guide Encore E 7 LCD Remote Transceiver RA D a D D A The lock icon will be displayed when system is ARMED Driver paging Someone is paging you in your vehicle Hood Trigger Hood is illegally opened Zone 1 Door Open Warning Doors are illegally opened Zone 3 Ignition Trigger Ignition switch is illegally turned on Zone 5 Remote Transmission You are transmitting to the control unit Anti Car Jack Mode Activated Engine Cranking Your vehicle engine Cranking by remote control The unlock icon will be displayed when the system is disarmed Manual Gear Mode programmed Trunk Trigger Trunk is illegally opened Zone 2 Sensor Trigger Trigger on shock Sensor 1 Zone 4 System trigger In Range Indicator You are within the range of the remote control Button Lock icon on Engine Running Your vehicle s engine is running Daily Start Engine will start automatically at the same time next day sig Timer Control Engine will start automatically every 2 or 3 hours TEMP Temperature Start Z Valet Mode SUAUS Engine will start Remote start2. and automatically when the programmed temperature is reached alarm functions Activate Channel c3 o C4 Time Monitor 4 Parking Meter Parking meter reminder time Alarm Clock Alarm clock set Ie 00 l i Lo kanas a na l Low Battery Oe i the battery of remote control K De Pressing the Star Power Save 0 and trunk buttons nnn battery icon full bar together Briefly will flash turn ON the transmitter backlight BATTERY CHANGING Depending on the usage the remote batteries should be changed at least once a year in the one way remote and once every 4 5 months for the two way remote The 1 way remote E 7s is powered by a pair of 3V CR2016 batteries These batteries are available at most locations batteries are sold and can be replaced by the user Battery Level Indicator 2 way remote The Battery Level indicator has three level indicators that serve as a visual indication of battery charge When the battery reaches a low charge level that requires changing the remote control will generate a single notification chirp and the Battery Level indicator __ will flash continuously If the battery voltage is LOW the range of the remote will be reduced by 50 to conserve battery life The two way remote requires 2 3 Volt CR2032 batteries The operation lives of these batteries are affected by many factors including temperature usage back light ON time and programmable in range
3. and be aware of 1 Keep the transmitter out of children s reach 2 Do not leave anyone in the vehicle while running on remote control 3 Alert servicing personnel that the vehicle can be started automatically 4 Do not start the vehicle by remote while it s in an enclosed area or garage 5 Always apply the parking brake and lock the vehicle as you exit the vehicle 6 The vehicle windows must be rolled up 7 Should the unit malfunction disconnect the fuse until the problem is corrected 8 The use and operations of this system is the sole responsibility of the operator 9 Some areas may have local ordinances that prohibit leaving a vehicle running on public streets 10 It is not safe to remote start the vehicle if the vehicle is parked on a steep incline TO REMOTE START THE VEHICLE When you want to start your vehicle 1 Press button once on the transmitter 2 The parking light will activate to indicate the remote start received the signal 3 The engine will start in approximately 5 seconds 4 Once the engine is running after couple seconds the parking lights will turn on and the climate controls will activate and adjust the vehicle s interior temperature to your preset setting While the vehicle is running the minutes digit on the LCD screen will flash and the will indicate countdown timer based on the 5 10 20 or 30 minute run time set up by your installation center 5 The vehicle will ru
4. car jacking mode the system will be triggered when any door is opened and closed while the ignition is ON PASSIVE ANTI CAR JACKING Programmable lt will operate as noted below 1 Turn the ignition switch to the ON position and the system will arm 2 Once the system is armed if you are forced from the vehicle the system will trigger when the door is opened and closed while the ignition is ON TRIGGERING THE ANTI CAR JACKING MODE A 50 seconds after the system has been triggered The siren will start chirping for 15 seconds B During this 15 second period of chirping you will be alerted to push the valet switch once to turn off the car jacking feature If not it will enter a second timer for carjacking C 65 seconds after the system has been triggered the siren will start sounding and the parking lights will start flashing D 90 seconds after the system has been triggered 1 The siren will sound and the parking lights will flash and 2 The starter disable will activate to prevent the vehicle from starting 3 it will remain active until the vehicle s battery power is exhausted OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR JACKING Turn the ignition switch from OFF to ON and within 10 seconds push valet switch the siren will stop and the system disarmed Remote Start Operation WARNINGS As with any product that performs automatic functions there are certain safety precautions that you must practice
5. control on 1 Before turning off the engine press the oe button once on the transmitter and the LED indicator will flash 3 times to confirm enter 2 Turn the ignition key to OFF position The engine will stay running 3 The engine will run until the pre programmed time elapsed or shutdown input is received TURBO CHARGE MODE Turbo charger mode keeps the engine running after arriving at your destination for a programmable period of 1 3 or 5 minutes This allows the vehicle s engine time to conveniently cool down the turbo after you have left the vehicle For use Please download the complete manual TIMER START Please download the complete manual This unit can be programmed to start and run the engine every 3 hours or punctually at the same time next morning the engine will run for the programmed running time and then shut down IMPORTANT Timer Start should be used only in open areas never start and run the vehicle in on enclosed space as a garage or carport Please be sure you fully understand this feature before use TEMPERATURE CHECK Please see advanced user menu below TO TURN OFF THE REMOTE START When the engine is running by remote start if you want to stop it Press button once on the remote transmitter under the remote start mode Press this button twice if the unit is programmed to child safety start Press the brake pedal The vehicle will shut down and turn off the parking light to indicate th
6. status settings Do not allow these batteries to corrode or become wet for any extended period of time temporarily disabled Activate Channel 4 You have to change ACTIVE ARMING LOCK amp ARM 1 Press HM button on the transmitter 2 The siren will chirp once and parking light will flash once indicating that the system is now armed The vehicle s doors will lock upon arming if interfaced with the security system DEFECTIVE SENSOR REMINDER If the siren sounds 3 chirps then you have left a door trunk or hood lid ajar SILENT ARMING DISARMING Press the transmitter a and al buttons at the same time This will arm or disarm your security system No chirp sound will be heard arm disarm confirmation will be through the vehicles parking lights only SENSOR BY PASS Press the fa button two times within 5 seconds will arm the security system and by pass the shock sensor HIDDEN ALARM FUNCTION Silent Alarm Press the a button first within 3 seconds press the a button to activate the hidden alarm function The security system will arm and with Hidden Alarm Mode The siren horn will be silenced even if the sensor is triggered in the armed mode Alarm indication will only appear on the LCD Transmitter PASSIVE ARMING Programmable Active arming disarming is controlled by your security system via the remote transmitter This security system is equipped with an optional Passive Arming feature which allows
7. CAR LOCATOR Under armed mode press the fa button to active car locator function The siren will chirp 6 times The parking light will flash 12 times for you to easily locate your car PANIC FUNCTION The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency Press and hold the a button for 3 second The alarm will immediately sound To stop the alarm press the trunk ya button on the remote control If the button is not pressed the alarm will automatically stop after 30 seconds TRIGGER THE SYSTEM When armed your vehicle is protected as follows Light impact will trigger the warn away signal Heavy impacts Doors open if installed Hood open if installed Trunk open Turning on the ignition key will trigger the programmed sequence The starter disable relay if installed prevents the vehicle s starter from cranking The siren horn parking lights and dome light will turn on alerting of an intrusion for 30 seconds Then it will stop and automatic reset and re arm If the any one of the sensors or detectors is still active the alarm system will sound a maximum of 3 times of 30 seconds cycles NOISE ABATEMENT CIRCUIT Your system has a Noise Abatement Circuit It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Here s how Noise Abatement Circuit works The shock se
8. adjust parking Hour value from 0 to 2 Complete adjust Hour Press al button or ie adjust parking Minutes value from 0 to 30 Press W button complete count down timer setting or a button to adjusts hour from 0 to 12 then press al button or a button Adjusts clock Minute from 0 to 59 Press a button complete Daily Start setting or press button 2 sec to activate Daily start as indicate on LCD display and exit programming mode Power Save mode ON OFF LCD remote transceiver uses 0 current to save the battery power Exit Press ya buttons or not press any button within 10 seconds it will exit remote programming mode automatically Low Battery Indication When the power of the battery weakens it has two short bi sound and flash LL icon while pressing the button of the LCD screen transceiver Stop The Trigger Melody Sound While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon press any button on the LCD remote transmitter to stop melody sound only the remote control buttons will not send a command to the system saezapere Automotive Systems LLC All rights reserved For Warranty information Please go to www encoreautomotivesystems com and download the complete users manual For customer service please call us toll free 855 GO ENCORE 855 463 6267 8 00 5 00 PST Thanks for your purchase
9. e engine has stopped SHUT DOWN INPUT FOR REMOTE STARTER If any of the following conditions exist while the system is operating the engine will not start or will shut down immediately The hood is opened The brake pedal is pressed Press The system triggers OND ARON attempts The parking hand brake is released For Turbo Timer Mode Engine is over revved Tachometer checking type only The pre programmed run time 5 10 20 30 minutes has elapsed button on the remote transmitter under remote start mode The vehicle refused to start running after 3 unsuccessful ADVANCED USER S MODE LCD REMOTE TRANSCEIVER OPERATION Transmitter button LCD Press amp Hold ya for 2 seconds until 1 chirp is heard Press a button Press a button Press ya button Press xk button Press amp hold button Button Lock for 2 sec Press amp hold a button for 2 sec Press amp _ hold ya button for 2 sec Press amp hold button for 2 sec Feature amp remark Backlight turns on for 3 seconds Press amp Hold ie for 2 seconds chirp one time LCD display show U 01 enter 1 programming of LCD Remote Press e button check the vehicle s status Press a button check the system trigger condition Press button check the vehicle s temperature PRESS button FOR OPTION OF CAR 1 CAR2 Press amp hold A button for 2 sec Button Lock O
10. ill Arm 1 flash Arm automatically re arm itself in 60 seconds after disarming with remote 2 chirps Disarm 9 flashes Disarm transmitter Automatic rearm will cancel if any door is opened before the 60 3 flashes Disarm Triggered seconds timer has elapsed DISARMING WITHOUT A TRANSMITTER The Override function may be used if the remote transmitter is lost or inoperative 1 Enter the vehicle and turn the ignition switch to the ON position 2 Alarm will sound 3 Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode You can now start and operate the vehicle normally VALET MODE System is in Disarm Mode The valet switch allows you to temporarily bypass all alarm function eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm functions and remote start functions are bypassed however the remote panic Defective Reminder Disarm Triggered 12 flashes 6 chirps Constant On Under Remote Start ALARM OPERATING CONDITION Siren Parking Dome ee ee Slow Flash Flash Locking Locking Disable ae on second 3 Trigger Alarming Flashes Slow Flash Disable Flashes feature and remote door locks will remain operational To use the valet 4 Passive mode the system must first be disarmed either by using your remote Starter Fast Flash Disable transmitter or by operating the Manual Override
11. n 1 beep Off 2 beep default Off Press amp hold a button for 2 sec Vibrator or Melody mode selection Melody default Press amp hold ya button for 2 sec Fast Count Timer Off 20m 30m 1HR 1 5HR 2HR Down 10m Press amp hold button for 2 sec Button Beep Sound mode Enable 1 beep Disable 2 beeps default disable Table 2 two beeps to confirm LCD Display System feature amp remark Press amp hold button ya X for 3 seconds Two chirps will be heard 0 ic is flashing 2 0 Ut is flashing Alarm Clock adjust 12 is flashing UU is flashing Count Down Timer setting iZ is flashing Daily start PLEASE READ THE COMPLETE MANUAL FOR THIS MODE DAILY START icon flashing NEVER REMOTE START A VEHICLE THAT IS PARKED IN AN ENCLOSED SPACE EXTREME CARBON DIOXIDE DANGER Press amp hold button me HK rs seconds chirp x 3 Full battery icons flash clock time adjust or o button to decrease or increase Hour digit adjust hour from 0 to 12 Complete adjust Hour Press al button or ie button Adjusts clock Minute from 0 to 59 Press a button complete clock setting or ie button to decrease or increase Hour digit adjusts clock hour from 0 to 12 Complete adjust Hour Press button or ya button Adjusts clock Minute from O to 59 Press a button complete Alarm clock setting or a
12. n for a programmable 5 to 30 minute cycle before shutting down When the unit shuts off the countdown timer will turn off and the transmitter will play a melody NOTE The Remote Start Unit will not start the vehicle if any one of the following conditions exists 1 The hood is opened 2 The brake pedal is pressed 3 The optional remote start enable toggle is switched to the OFF position If installed 4 The gear selector is in any gear other then PARK or NEUTRAL SAFE START Child safety mode Factory default is set to press the button once on the transmitter to start the vehicle You can program this feature to eliminate an accidental remote start 1 The user presses the transmitter buttons twice within 3 seconds to start the vehicle or NOTE Contact your installing dealer to activate this feature OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START To operate the vehicle while the engine is running from the remote start Insert the ignition key and turn it to ON not the start position Press the brake pedal Note If the brake pedal is pressed before the key is in the ON position the engine will shut down TEMPORARY STOP FEATURE This feature allows the vehicle to remain running after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate
13. nsor triggers five times the Noise Abatement Circuit will interpret this pattern of triggers as a false alarm After the 5 trigger the Noise Abatement Circuit ignores or bypasses that sensor or switch until a different sensor or switch is triggered TRUNK RELEASE Press and hold a button on the transmitter for two seconds to remotely control the trunk release CHANNEL 4 OUTPUT Press the transmitter a and ye buttons at the same time to active Channel 4 function Channel 4 is a user programmable timer outputs You may program the built in timer to send a ground signal for any time duration from 1 second to 120 seconds For instance this timer output may be used to turn on the headlight power window or sunroof Factory defaults setting at Pulse output Stopping The Trigger Melody Sound When the alarm is triggered the LCD screen will alert the user with a melody sound and a flashing trigger icon Press any button on the LCD remote transmitter to stop melody sound ANTI CAR JACKING Programmable Warning If you don t need the carjacking function in this alarm system be sure to set carjacking feature OFF This systems default setting is OFF for all carjacking modes ACTIVE ANTI CAR JACKING 1 Ignition ON press and hold the fi and al buttons at the same time for 2 seconds The parking lights will turn on for 1 5 seconds to indicate the system has entered the anti car jacking mode 2 Once the system in anti
14. or seconds Pass will appear on the remote Arm System and Silent Alarm has been completed PASSIVE ARMING BY PASS While the system is disarmed Press the ye button twice the system will respond with 1 chirp and LED will turn ON The security system will remain in this temporary state for as long as you wish To exit passive by pass press the transmitter m or al buttons and the system will return to normal status ACTIVE DISARMING UNLOCK amp DISARM 1 Press m button on the transmitter 2 The siren will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed The vehicle s doors will unlock TAMPER DISARMING If the alarm is triggered upon disarm the system s siren will chirp 4 times and the parking lights will flash 3 times telling you the alarm has been triggered during the last armed state PATHWAY ILLUMINATION When receiving an unlock disarm signal this feature will turn the parking lights ON for 30 seconds and for 10 seconds upon the lock signal Programmable Activate or Turn Off The Remote Start K Press Twice if set to start D mode BOO BOO Channel 4 Channel 4 Timer Output 4 Channel 4 Timer Output 4 Optional De Switching code For 2nd Car For regular remote X 0 Operation transmitter CHIRP INDICATORS PARKING LIGHT Function Parking light Function AUTOMATIC RE ARM If this feature is selected the security system w
15. sequence Disable a Under disarm mode turn the ignition to ON position 5 Panic Aee Flashes Flashes b Press and hold valet switch for 2 seconds until the LED turns ON solid The LED will remain on as long as the system is in valet mode Exit Valet Mode a Turn ignition ON b Push and hold valet switch for 2 seconds The LED will turn off indicate the system are exiting the valet mode E car sanal Aemme fFe ato Fis 12
16. the security system to arm 30 seconds after the last door is closed Operation is as follows Press S within 3 seconds 1 Turn the ignition to the OFF position and exit the vehicle uncon and Hold th e button 2 After all entrances are closed the security system LED will flash fast for 30 seconds If you reopen any door hood trunk the security system Ignition in off position Silent Arming Disarming LED will stop flashing It will begin flashing again once all vehicle Ignition in on position press entrances are closed Active Anti Car Jacking Mode 9 and hod a 3 After the 30 second time has elapsed the security system will Unlock Doors amp Disain System automatically ARM The siren will chirp 1 time and the parking lights Press twice within 3 seconds will flash 1 time Two Steps Door Unlock amp Press and Hold for 2 seconds and Hold for 2 seconds PASSIVE ARMING WITH PASSIVE DOOR LOCKING Disarm System optional The vehicle doors will automatically lock after the passive arming cycle Trunk Release Channel 3 Passive Arming By pass Ress ane Hot ert sean the system Disarmed Press button once or X E REMOTE TRANSMITTER OPERATION Transmitter Button System Function Lock Doors amp Arm System Panic function Press and Hold for 3 seconds Press Trunk ya button to stop panic function Car Locator Press when in armed mode Arm and Delete The 2 Stage Press fa twice within 3 Shock Sens
Download Pdf Manuals
Related Search