Wireless Door Chime User`s Manual
Contents
1. 46 19230 2 Wireless Door Chime User s Manual Chime Push Button Thank you on your purchase of the Wireless Door Chime Before installation please read this manual carefully and keep for future reference 5m Reguired Tools e Flathead screwdriver e Drill e 1 16 drill bit e 5 32 drill bit e Phillips screwdriver Included Hardware e 2 Plastic anchors e 4 Screws e 1 Double sided Tape e 1 12 Volt battery Battery Installation Chime Unit 1 Make sure the Chime power is switched to the OFF position 2 Remove battery cover by pressing the tab in the direction of the arrow and lifting at the same time 3 Install 2 AA batteries noting the battery orientation inside the battery compartment 4 Replace battery cover Push Button 1 Remove battery cover by using a small flat screwdriver 2 Insert flat screwdriver in at the bottom of the Push Button to release the tab 3 While the flat screwdriver is inserted at the bottom of the Push Button press downwards to separate the battery cover from the Push Button 4 Remove plastic tab in between the 12V battery and contact tab to allow button 3 i EA to operate 2 i Linking the Push Button to the Chime Unit 1 Switch the Chime power to the ON position The red LED will begin blinking slowly 2 Within 10 seconds of turning on the power press the push button The LED on the chime will blink rapidly and turn off The2. screwdriver Remove the old push button and use this location to install your new Push Button described in the installation of the battery Use the battery cover as a template to mark the position of the screws hole for each screw mount the back cover using the screws provided Note The back cover has an arrow and the word Up embossed on the inside of the cover Position the back cover with the arrow pointing upwards and the word Up is at the top Press the Push Button on to the back cover by inserting the top of the Push Button onto the top of the back cover first and then pressing on the bottom of the Push Button to snap the bottom of the Push Button into place Installation using the provided Double Sided Tape 1 Clean the surface where you would like to mount the Push Button and the back of the Push Button Use a mixture of 50 50 water to isopropyl alcohol Remove the battery cover as described in the installation of the battery Remove the backing from one side of the double sided tape and press it onto the back of the back plate of the Push Button Remove the backing from the other side of the double sided tape and press the back plate to the cleaned mounting surface Note The back cover has an arrow and the word Up embossed on the inside of the cover Position the back cover with the arrow pointing upwards and the word Up is at the top 5 Press the Push But
3. Chime and Push Button have been successfully linked 3 To test press the Push Button and the Chime Unit should chime Note If linking fails or you change the batteries or turn the Chime Unit off and back on you will have to re link the Push Button to the Chime Unit Perform steps 1 and 2 in the Linking the Push Button to the Chime Unit Low Battery Indicator The Chime Unit has a low battery indicator feature When the battery is at 25 percent capacity the LED on the Chime Unit will begin to blink and will continue to blink each time the Push Button is depressed Replace the batteries and the LED will stop blinking You will have to re link the Push Button to the Chime Unit Installing the Push Button 1 Push Buttons are mounted at the same height as the door knob or handle between 36 44 above the floor Remove the old push button and use this location to install your new Push Button 2 Before mounting the Push Button run a test Place the Push Button as close as you can to where you would install it Place the Chime as close as possible to its installation site Press the Push Button and see if the Chime rings If the Chime does not ring see Troubleshooting Remember Button should be no farther away than 150 ft from the chime and test before installation Installation using the provided screws 1 Remove the battery cover as Using a 1 16th inch drill bit drill a pilot Using a Phillips head
4. found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this eguipment does cause harmful interference to radio or television reception which can be determined by turning the eguipment off and on the user is encouraged to ry to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the eguipment and receiver Connect the eguipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 10 10 11 is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC 10 E Memorial Road Oklahoma City OK 73114 This Jasco product comes with a limited lifetime warranty Visit www jascoproducts com for details
5. stalled according to the polarity markings inside the battery compartment on the Chime Unit 2 Make sure the battery is installed according to the polarity markings inside the battery compartment on the Push Button 3 Try installing new batteries 4 Make sure the Chime Unit is no farther than 150ft from the Push Button 5 Try moving the Chime Unit to a different location that is within the 150ft range 6 Make sure the Push button is not mounted on a metal surface on or near metal studs or near the floor Push Button should be mounted 36 to 44 from the floor 7 Make sure the Push Button and the Chime Unit is properly linked Refer to the section Linking the Push Button to the Chime Unit a o Functional range may be adversely affected by one or more of the following factors e Weather e Radio Frequency Interference e Low Transmitter Battery Push Button e Obstruction between Push Button and Chime Unit FCC Statement This device complies with Part 15 of FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference 2 This device must accept interference that may cause undesired operation FCC NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment NOTE This equipment has been tested and
6. ton on to the back A i A cover by inserting the top of the Push VX Button onto the top of the back cover M first and then pressing on the bottom M of the Push Button to snap the bottom v of the Push Button into place l h A Installing the Chime Unit Note Avoid mounting the Chime Unit on metal surfaces as this may result in reduced range of transmission The Chime Unit should also be mounted no farther than 150 feet from the Push Button No further than 150 fest away 1 Select a mounting location that is within the 150ft range 2 Use the supplied Chime template to mark mounting holes a If mounting to sheetrock i Using a 5 32nd inch drill bit drill holes at the marked locations ii Insert the two wall anchors supplied M iii Screw in the two screws supplied leaving a 1 4 of the screw extended out from the mounting surface See ve TP diagram iv Place the Chime Unit s keyholes over the screws and gently press downwards to secure Chime Unit b If mounting onto or into wood x i Using a 1 16th inch drill bit drill pilot holes at the marked locations T ii Screw in the two screws supplied leaving a 4 l of the screw extended out from the mounting surface See diagram i Place the Chime Unit s keyholes over the screws 7 and gently press downwards to secure Chime Unit Chime Template Q ON Q Troubleshooting 1 Make sure the batteries are in
Download Pdf Manuals
Related Search