EUKT03-CW60 User Manual
Contents
1. 20V AC input power must be completed by a licensed electrician Please check your local codes prior to beginning any project All 12V DC output circuits meet Class II lighting requirements and are safe for do it yourself installation Please read these guidelines before installing Disconnect the AC DC power supply before making any cuts or connections Do not connect power to the LED strip lights while they are coiled on the reel Do not install or use this kit in wet or damp locations Use LED strip lights only with a low voltage 12V DC power source and 5 24V DC Controller To protect the eyes do not stare directly into the LED lights when they are lit Make sure to use the and indicators on the LED strip lights to maintain polarity and correct sequencing For running wires inside walls use properly certified CL2 or better cabling Do not install Class 2 low voltage wiring in the same runs with AC main power wiring If AC and DC wires cross keep them at 90 degree angles Peel Connect Remove the 3M tape Simply use the wire backing from the LED strip interconnects and lights and stick in place connectors to join the LED strips Cut Locate the cut lines on the RGB strip light and cut strip to desired length Figure A Figure B Copper pad location Soldered copper pad location al gt g g BE JC ti Cut the LED strip light using scissors Make sure to cut strip in the center of the copper pad locatio2. Tape 5050 smd 60 LED meter 12V DC maximum Operation temp 20 50 C Non waterproof View Angle 120 degrees Storage Temp 30 C 80 C Power per meter 72watt Color Cool White IP20 PRESET BRIGTHNESS SELECTION 50 Brightness 100 Brightness EUKT03 CW60 Connector Use for AWG 22 LED strip thickness 0 3mm Current 5A AC DC Voltage 12 24V DC Operation temp 40 105 C Voltage Resistance 1500V AC min Contact Resistor 30m max 1000m min Housing PA6 Contact over Brass Tin Tooth Slice double Tin Size 12 88mm x 15 48mm x 3 3mm w EUComtrols EUKT03 CW60 Standard Product Warranty PRODUCT WARRANTY EuControls warrants that at the time of shipment the standard products manufactured by EuControls and sold hereunder will be free from defects in material and workmanship for a period of three years from the date of shipment Warranty Adjustment Buyer shall notify EuControls immediately if any defect within the warranty period should appear EuControls agrees to repair or furnish a replacement for but not install any product which within three 3 years from the date of shipment by EuControls shall upon examination by EuControls prove defective within the above warranty period No product will be accepted for return or replacement without written authorization of EuControls Upon such authorization and in accordance with instructions by EuControls the product will be retur
3. gular spaces since this might damage the LED s w EUuComtrols ALORS AND LIGHTS UNDER YOUR CONTROL EUKT03 CW60 OPERATIONAL MANUAL Turn the Knob counter clockwise Turn the Knob clockwise to to OFF or decrease brightness ON or increase brightness Power ON OFF To Cancel Timer function Select desired Brightness Press for high or for low Preset Brightness Control Timer option Color Mixing Q Battery in back Note e If button works properly then a buzzer will be heard when it pressed e Tear the sticker on the buzzer away to make it louder EuControls Corp Los Angeles California www EuControls com ae EuConmf trols SPECIFICATIONS Dimmer Power Supply Output Power 100W DC 12 24V Output Voltage 12V DC Power 84 168W Output Current 0 8 33A Input Voltage AC 100 240V 50 60Hz Channel Range Voltage AC 90 264V 47 63Hz Brightness adjustments Over voltage Protection 120 min Over current Protection 120 min Load Regulation 5 Ripple and Noise 100mV Operation Temp 0 40 C Storage Temp 20 85 C Operation Humidity 5 95 Size L 156 x W 67 x H 40 mm Input Voltage Output Current 7A 1 Remote Control Controller IR remote control Brightness adjustments Present Brigthness Manual and Preset Cord Input cable wire stripped and tinned 18 AWG black power cord 120VAC 25 Brightness 75 Brightness LED
4. l colors mounting angle and objects can all affect the lighting appearance Before installing this LED lighting kit please consider the following Location of the power supply and the dimmer Controller LED Lighting ON and OFF plan The layout the configuration you will be using Wire connections to your LED strips w EUuUComtrols EUKT03 CW60 Typical Configuration Options Straight LED Connection LED Strips Controller Array LED Connection Heres cee ESReSlien cone LED Strips ernennn tren Loop Back LED Connection rm LED i LED Controller Center Feed LED Connection LED Strips LED Controller w EUuUComtrols EUKT03 CW60 INSTALLATION INSTRUCTIONS Power Supply Remote Control Input Voltage 100 240VAC Output Voltage 12V DC 11 Dimmer Controller wod ano LED Strips After you had determined the mounting position you are going to use e Make sure to clean the surface area The area should be free from oil or waxes and should be smooth and dry to ensure proper adhesion of the 3M tape on the back side of the Led strip light e Gently remove the 3M backing and press the Led strip light between the LED s to securely contact the surface of the mounting surface Never press on the individual LED s since this could damage their solder connections to the strip e Avoid sharply bending the LED strip solder joints in curves or irre
5. ned shipping charge prepaid by Buyer Replacements made under this warranty will be shipped prepaid by Seller Exclusions from Warranty This warranty does not extend to any products manufactured by EuControls which has been subjected to misuse neglect accident improper installation or use in violation of instructions furnished by EuControls This warranty does not extend to or apply to any unit which has been repaired or altered other than at EuControls factory or by persons not expressly approved by EuControls Components purchased or made by Buyer from any supplier other than EuControls shall bear only the warranty given by the manufacturer of that product and EuControls assumes no responsibility for the interface of its product with any other product and such responsibility shall remain with Buyer for interface functionality and intended use Notice The foregoing warranty is in lieu of and excludes all other expressed or implied warranties of merchantability or fitness for use or otherwise EuControls Corporation 19210 S Vermont Ave Ste 310 Gardena CA 90248 United States Toll free sales hotline 1 888 535 9580 Tel 1 810 643 5700 Fax 1 310 643 5688
6. ns as shown in the Figure A If you cut at a soldered location refer to Figure B You may need to remove the solder from the RGB strip light connection joint in order for the butt connectors to work properly w EUComtrols EUKT03 CW60 Connecting Carefully slide the LED Fa Insert the DE tape into the connector so SS LED strip IIN Z that copper pads on the NY N a into the i LED strip are positioned channel underneath the connector lt eee ae contacts Qh under l Figure 1 contact tabs Figure 2 a Snap the lid down to close the r4 connector Perform a test to S be sure that the connection is YN NY correct and that the LED s light before proceeding with the Figure 3 final installation Important Make sure to keep the correct polarity of indicators printed on the LED tape light to ensure correct color sequencing a F arc i owe fees l If necessary the LED wires can be extended using 4 conductor 22 18 AWG wire But the shorter the length of wire added or the larger the wire gauge the less chance for voltage drop which would allow for higher LED brightness Please consult your electrician if you are unclear about your connections Planning EUKTO3 Kit is designed for indirect lighting applications The light from the LED strip should not be directly visable Every design is unique and the lighting effects depend on your personal preference The installation location surfaces wal
7. w EUuUComtrols EUKT03 CW60 LED STRIP LIGHTING KIT EUKTOS3 CW60 This kit comes complete with everything you will need to light up your project It includes a deluxe LED dimmer controller a mated AC DC power supply 16 4 of LED strip light and six light strip connectors In some cases you may need to splice connecting wire to power the LED strips or make extended turns It is recommended you first read these guidelines completely to understand how the products work and how they can be configured to your desired lighting layout Please note All wiring must comply with local and national electrical codes for Class II lighting If you are unclear on how to install this product please contact a licensed electrician All 120V AC main connections should be made by a licensed electrician What s included in the KIT Part Number Description DU3 10700 IR Dimmer EUACRE 002 Dimmer Remote EULSC0260 5 0 CW LED Strip Light Wired Interconnect with End to End connectors EUABCON W10 Butt Connectors MKTO3 Revi1 Owner s Manual If any parts are missing please call 1 888 535 9580 Cc Ta AntrA lo CC Arr AC An INQ AC Al if Arrn 1 ry LAINVAINAT E x nny trn oC RMArY CULONTOIS Lorp LOS Angeles VUaillformla WWW CULONTTOIS CcCOM y j M3 w EUComtrols EUKT03 CW60 The AC DC power supply is UL listed and ready to use in a standard 120V AC outlet Any alterations or wiring modifications i e hardwiring to the 1
Download Pdf Manuals
Related Search