Home

Manual - Process Controls

1. SHARK7x MULTI PARAMETER TRANSMITTER USER S MANUAL Rev 2 AquaMetrix Inc Tel 800 742 1413 1245 Maple Hill Ct Unit 7 905 954 0841 Newmarket ON Fax 905 954 0415 Canada L3Y 9E8 www aquametrix com MULTI PARAMETER TRANSMITTER USER S MANUAL C Table of Contents Subject Introduction Section 1 Specifications Section 2 Installation Section 3 Electrical Connections amp Setup Differential Probe connection amp setup Combination Probe connection amp setup Conductivity Cell Contacting style connection amp setup Paddle Wheel Flow Sensor connection amp setup 4 20mA Isolated Output Section 4 Using the Transmitter in pH Mode LCD Menu Section 5 Using the Transmitter in ORP Mode LCD Menu Section 6 Using the Transmitter in Conductivity Mode LCD Menu Section 7 Using the Transmitter in Flow Mode LCD Menu Appendix A Probe Configuration Table Return Policy amp Warranty Plan Page No 12 13 29 30 45 46 63 64 79 80 28 44 62 78 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Introduction The SHARKrxe multi parameter transmitter is a microprocessor based transmitter capable of measuring one of the following parameters pH ORP conductivi ty or flow When shipped from the factory the Shark is not set to measure any one parameter When the Shark is powered up for the first time it will di
2. Example If the controller has been running in GPM mode and has a totalized flow changing from GPM to another unit will reset the totalizer to zero ME CUBIC FEET UNITS OF VOLU LITERS US GALLONS GP gt Use the P gt or keys to scroll through the available ranges To select a specific predefined unit press the 47 key once which will move the cursor back to the RH side of the display UNITS OF VOLUME CUBIC FEET gt DOWN To select custom units press the press the Q key then the key which will move the cursor back to the right hand digit of the custom over the last character of the volume unit setting Press the key to accept the setting and move to the store function In this example the units will be changed to ML milliliters and the multiplier changed to 3785 4 since one U S Gallon equals 3785 4 NOTE ACCELERATOR KEYS Pressing the or Gown key once will change the value by the smallest digit Holding the key down will cause the value to change at an increasing rate until the key is released Pressing the key again will cause the value to start changing at it s slowest rate again This allows the user to get to the new multiplier value quickly NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE unit character UNITS OF VOLUME gt CUSTOM 7 gt keys to select the appropriate text characte
3. Isolated Output Range expand 0 to 100 of full scale min segment 10 of full scale max load 8000 Memory Back up All user settings are retained indefinitely in memory EEPROM Enclosure NEMA 4X 1 4 DIN polycarbonate enclosure with two 1 2 conduit holes Mechanical SHARK xP Enclosure NEMA 4X front panel 1 4 DIN polycarbonate SHARKrx Mounting Universal Mounting kit for surface pipe and panel mount included SHARKrxp Mounting Panel and DIN rail mount included Sensor Input Probe 600 to 600mV Probe 1999 to 1999mV Temp Sensor 0 to 9999Q Temp Sensor 0 to 99990 Cell 0 to 99990 Temp Sensor 0 to 99990 Paddle 0 to 2000Hz Invalid Entries Invalid entries cannot be stored Manual Test Mode Process value can be simulated with arrow keys to verify correct setup of output Output Hold to 20mA output is placed on hold when the transmitter is in Menu mode Recall data from last Recall data from last calibration calibration mode calibration calibration buffer Calibration Data Ist amp 2nd accepted buffer value and probe mV output accepted value and cell Recall store K factor calibration temperature calibration slope and probe resistance calibration efficiency temperature Auto Return User selectable auto return if the transmitter is left in menu mode for more than 10 min Display Damping User can select rate at which the transmitter updates display Enables di
4. R K TX Section 3 Electrical Connections and Setup 3 4 pH or ORP Combination Probe connections and setup The drawing shows the connections for the Aquametrix Combination probe The cable should be run in a conduit separate from AC power wires and via a separate conduit hole The cable length should not exceed 10 feet 3 meters 2 wire version has 3 3 Connections for the 2 and 4 wire Combination Probe no temperature sensor WHITE 10 and is connected via a GREEN 12 coaxial wire COAX CENTER 11 In a pH meter the user THESE WIRES ARE ONLY PRESENT WITH 4 should set the T COMP WIRE COMBINATION OVERRIDE menu to ON COAX SHIELD 13 PRSE Section 4 10 and adjust JU PER 12443 Y the temperature setting to MUST BE INSTALLED FOR the actual probe temper ICUSTOMER ature In an ORP meter the ERN user should set the B E T DISP OVERRIDE to sis j ON Section 5 9 to blank the temperature reading on the display The 4 wire version has two additional wires for the probe internal tem perature sensor Ensure that the T COMP OVER RIDE or T DISP OVER RIDE is OFF NOTE JUMPER MUST BE SET TO STANDARD COMBINATION Dwg N104 43 pH or ORP PROBE Once connected step through the LCD menus to select the probe in the order shown The first two steps may be skipped if the meter is already configured for a Combination Probe I
5. simply return to the Display Damping Menu This function is useful if you wish to view the current selection without DISPLAY DAMPING making any changes STORE N DOWN Then press the Cow key to store the selection and return to the Display Not stored Stored Damping Menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Setup Menu Display Damping 4 11 Page 24 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Diagnostics Menu Firmware Rev 4 12 The FIRMWARE REV menu allows the user to see what revision of the firmware is currently installed in the controller This is a Read Only menu item NOTE 0 PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Diagnostics Menu Firmware Rev 4 12 Page 25 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Diagnostics Menu Calibration Data 4 13 7 15pH 25 0C RUN MODE The Calibration Data menu is a series of read only screens which allow the user to view the data collected during the last calibration Press to view the first Calibration Data screen CALIBRATION DATA Calibration Mode MODE 2PT 2 point calibration Press to view the next Calibration Data screen CALIBRATION DATA 1st POINT PH 7 00 1P 7 00 19 gt INPUT FROM PROBE 19 mV CALIBRATION DATA 2nd POINT PH 4 00 2P 4 00 143 E INPUT FROM PROBE 143 mV CALIBRATION DATA Probe Temperature at which
6. A warranty claim will not be honored if defects are not reported within the warranty period or if AquaMetrix determines that defects or damages are due to normal wear misapplication lack of maintenance abuse improper installation alteration or abnormal conditions AquaMetrix s obligation under this warranty shall be limited to at its option replacement or repair of this product The product must be returned to AquaMetrix Inc freight prepaid for examination The product must be accompanied with an MSDS for all the process chemicals used must be thoroughly cleaned and any process chemicals removed before it will be accepted for replacement or repair AquaMetrix liability shall not exceed the cost of the product Under no circumstances will AquaMetrix be liable for any incidental or consequential damages whether to person or property AquaMetrix will not be liable for any other loss damage or expense of any kind including loss of profits resulting from the installation use or inability to use this product Return Policy amp Warranty Plan Page 80
7. MULTI PARAMETER TRANSMITTER USER S MANUAL IF BUFFER1 READY PRESS DOWN RUNNING MANU CAL BUFFER1 WAIT MANUAL CAL pH BUFFER1 73 MANUAL CAL pH BUFFER1 o o MANUAL CAL pH BUFFER1 obl IF BUFFER2 READY PRESS DOWN RUNNING MANU CAL BUFFER2 WAIT MANUAL CAL pH BUFFER2 4 410 gt MANUAL CAL pH BUFFER2 olol gt MANUAL CAL pH TX pH Calibration Menu Manual Calibrate 4 1 Place the probe in the first buffer solution be sure to clean and rinse the P robe first with D I water and then insert it in the 7 00 buffer Press The controller will read the pH value averaging a number of results to get a stable calibration value Please wait for the controller the measuremen to complete When complete the controller will report the measured value Use the and keys to adjust the reading until it agrees with the actual buffer pH value Then press cursor to the RH po to move the sition Then press to store the value and move to BUFFER2 Place the probe in the second buffer Be sure to clean and rinse the Probe first with D I water and then insert it in the 4 00 buffer Press The controller will read the pH value averaging a number of results to get a stable calibration value Please wait for the controller the measurement to complete When complete the controller will report the measured value Use th
8. With N selected pressing the key will NOT store the selection but simply return to the TEMP SENSOR Selection Menu This function is useful if you wish to view the current selection without making any changes Conductivity Setup Menu Temp Sensor 6 8 TEMP SENSOR 3 Conductivity Setup Menu Temp Sensor 6 8 TEMP SENSOR allows the user to select the type of temperature sensor used the in the probe The factory default for Conductivity is a 3000 o NTC thermistor The user can also select a 300 o NTC thermistor or a Pt 1000 RTD Press the 4 key once which will move the cursor over to the sensor type 3 000 NTC Use the Qu or to select the sensor type TEMP SENSOR 3 3 000 9 NTC gt Once the correct Sensor has TEMP SENSOR been selected press the G gt gt key once which will move the cursor back to the RH side of the display UP 000 NTC UP TEMP SENSOR 1 000 RTD TEMP SENSOR 3000 E Press the key to accept the change and move to the store function Or press the Gr key to highlight the Y character Then press the key to store the selection and return to the TEMP NOE Stored SENSOR Selection Menu Stored NOTE PRESS THE Qu AND ow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 54 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Setup Menu Auto Return 6 9 1000uS
9. INITIALIZE N The controller will initialize itself for a specific meter NOTE PRESS THE AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Utilities Menu Meter Selection 6 5 Page 51 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Setup Menu Conductivity Range 6 6 Conductivity Range will allow the user to select the measuring range of the instrument The ranges can be selected from any of the following 200 mS cm cell constant 50 20 mS cm cell constant 10 5000 uS cm cell constan 200 uS cm cell constant 0 1 20 uS cm cell constant 0 1 2 uS cm cell constant 0 01 19 99 cell constant 0 01 Mo COND RANGE Press the G gt gt key once 500045 Pl 4 which will move the cursor ELLAS 2 over the last character of the range Use the Qu or keys to scroll through the available ranges Once the correct range is selected move to the store function to save the selection Press the G gt gt key once which will move the cursor back COND RANGE to the RH side of the display 20 00mS cm Press the key to accept the setting and move to the store function With N selected pressing the key Or press the C to highlight will NOT store the selection but simply the Y character return to the COND RANGE Menu This function is useful if you wish to view the COND RANGE COND RANGE current select
10. Use the or keys to adjust the 20mA output to get exactly 20 The TUNE value can be adjusted over the range from 0 to 1000 these are unitless numbers used for tuning purposes only With N selected pressing the Gow key will NOT store the selection bu simply return to the OUTPUT Menu This function is useful if you wish to view the current selection without making any changes 4 20mA PROC gt STORE YN Not stored 4 20mA PROC STORE N Gown Or press key to highlight Stored the Y character press the G gt gt key once which will move the cursor to the first character of the value to be changed 4 20mA PROC zp 20 PROC 20mA OUT 1000 20mA OUT 1000 gt Bown Use the Cup and keys to change the setting 4 20mA PROC 20mA OUT 800 gt Press 4 key once which will move the cursor PROC pus to the RH side of the play 20mA OUT 800 Gown Press the key to accept the setting and move to the next setting If you wish to change the setting press the 4 key once which will move the cursor to the first character of the value to be changed 4 20mA PROC TE 4 20mA PROC 20mA TUNE 512 20mA TUNE 51 DOWN Use the Cur and keys to change the setting 4 20mA PROC 20mA TUNE 540 gt Gown Press the Gow key to accept the setting and move to the next setting Press the 07 key once which will move the cursor back to the RH side of the d
11. 4 20mA PROC 20mA OUT 1400 gt 4 20mA PROC 20mA OUT 14 00 DOWN Press the 4 key once which will move the cursor back to the RH side of the display Press the ow key to accept the setting and move to the next setting If you wish to change the setting press the Gr key once which will move the cursor to the first character of the value to be changed 4 20mA PROC 20mA TUNE 51 Use the ve and owe keys to change the setting Press the 4 key once which will move the cursor back to the RH side of the display 4 20mA PROC 20mA TUNE 540 DOWN Press the key to accept the setting and move to the next setting Page 28 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Section 5 Using the Transmitter in ORP Mode 1 4 TURN SCREWS FOR SHARKTX ONLY UNIT LABEL 2 LINE 16 CHARACTER 3 00 mV 2 0 C MM LCD DISPLAY MAIN MENU INTERFACE SCREEN MEASURE SHARK IS CONFIGURED FOR ENU PRESS DOWN LABEL TO INDICATE UNIT OF SIMPLE THREE BUTTON INTERFACE FOR FAST amp EASY SETUP REFER TO SECTIONS 5 0 TO 5 13 Section 5 Using the Transmitter in ORP Mode Page 29 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Menu Overview 5 0 500mV 25 0C RUN MODE MANUAL CALIBRATE MANUAL CAL ORP ORP PROLE SEC 5 1 CALIBRATE TEMP SENSOR IN ORP PROBE SEC 5 2 SIMULATE PROCESS VERIFY OUTPUTS SEC 5 3 SELECT TYPE OF SELECT TYPE PROBE SELECT ORP PROBE OF METER S
12. CAL TEMP 19 4C gt calibration was performed lt 19 4 C Calculated slope based on 2 59 16MV PH gt point calibration 59 16 mV pH CAL EFFICIENCY Calculated efficiency based on 2 EFF 9196 gt point calibration lt 91 96 NOTE PRESS THE C AND Gow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Diagnostics Menu Calibration Data 4 13 Page 26 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Diagnostics Menu Sensor Input 4 14 The Sensor Input Menu allows the user to view real time uncompensated process data from the probe This is a Read only menu item IAGNOSTICS FIRMWARE REV Press to view the Sensor Input data PROBE 18mV The top line shows the mV input from the probe TEMP 3310 The bottom line shows the actual value of the temperature sensor in ohms NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Troubleshooting a pH probe using the sensor input Sensor input displays the uncompensated sensor input data The pH probe values are dis played in mV millivolts The temperature sensor value is displayed in Q ohm Connect the pH probe as per Probe Configuration Table in Appendix A 1 Place the probe in buffer 7pH allow temperature to stabilize Probe should read OmV 50mV Temperature should read 3000 509 25 C Record both of these numbers 2 Place the probe in buffer 4pH Probe should read 160mV more than probe value at
13. GO IMMEDIATELY BACK TO DISPLAY DAMPING RUN MODE UPDATE gt DISPLAY DAMPING UPDATE 10 SEC Press the key to accept the setting and move to the store function DOWN If you wish to save the setting press the G gt gt key to highlight the Y character With N selected pressing the Gow DISPLAY DAMPING Y key will NOT store the selection but STORE simply return to the Display Damping Menu This function is useful if you wish to view the current selection without DISPLAY DAMPING making any changes STORE N DOWN Then press the Cow key to store the selection and return to the Display Not stored Stored Damping Menu ORP Setup Menu Display Damping 5 10 Page 40 MULTI PARAMETER TRANSMITTER USER S MANUAL 7 ORP Diagnostics Menu Firmware Rev 5 11 The FIRMWARE REV menu allows the user to see what revision of the firmware is currently installed in the controller This is a Read Only menu item NOTE 100 pP PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Diagnostics Menu Firmware Rev 5 11 Page 41 MULTI PARAMETER TRANSMITTER USER S MANUAL TX ORP Diagnostics Menu Calibration Data 5 12 The Calibration Data menu is a series of read only screens which allow the user to view the data collected during the last calibration Press F to view the first Calibration Data screen CALIBRATION DATA Calibration Mode 1 point calibration
14. MOUNTING BRACKET SCREW 10 24 X 3 1 2 SHARK7x UNIVERSAL MOUNTING BRACKET Dwg 105 101 gt Qm SHARK rxe TS32 DIN RAIL MOUNT CUSTOMER SUPPLIED TS35 DIN RAIL MOUNT CUSTOMER SUPPLIED TS35 DIN RAIL MOUNT TS32 DIN RAIL MOUNT Section 2 Installation Page 5 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K TX Section 3 Electrical Connections and Setup 3 1 Conduit Connections The has two 1 2 conduit holes at the bottom of the enclosure as shown on fig 2 1 The unit is shipped with these holes plugged with liquid tight conduit seals These must be left in unused holes to maintain the NEMA 4X integrity Use approved conduit hubs to connect the conduit connect these to the conduit before connecting to the enclosure 3 2 Power Connections Figure 3 1 Connections SHARK TX LOOP POWER CONNECTIONS SHARK TX WIRING INDICATOR ONLY NO OUTPUT ISOLATED CHASSIS 100 1 EARTH GND 4 LOOP 2 OPTIONAL NO CONNECTION 3 ISOLATED CHASSIS EARTH GND 4 SHARK TX WIRING SHARK TX WIRING DEVICE WITHOUT INTERNAL DEVICE WITH INTERNAL LOOP POWER ISOLATED CHASSIS Men and EARTH GND 4 100 1 LooP 2 OPTIONAL 2 OPTIONAL SEE TABLE FOR MAXIMUM LOOP RESISTANCE SEE TABLE FOR MAXIMUM LOOP RESISTANCE 24VDC SUPPLY SUPPLY LOOP RESISTANCE 16 18 20 22 24 26 28 30 32 Dwg N104 41 SUPPLY VOLTAGE DCV Sect
15. On line state NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Utilities Menu Manual Test Mode 6 4 Page 50 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Utilities Menu Meter Selection 6 5 100005 25 0 The Meter Selection menu is used to select the meter type that the DOWN controller is configured for either pH ORP Conductivity or Flow CALIBRATION Once selected the controller will initialize itself for the selected meter s CL functionality and move to run mode UTILITIES 4 1 TEST MODE Press the key to initialize the controller as a pH meter INITIALIZE Y gt Press key to initialize the controller as an ORP meter om INITIALIZE YN e DOWN Press the key to initialize the controller as a Conductivity meter To reset the controller back to all ICJONDUCTIVITY CONDUCTIVITY the factory default values reselect INITIALIZE Y N 4 the current meter type DOWN Press the key to initialize the controller as a Flow meter INITIALIZE YN lt DOWN Press the G gt gt key to Exit and return to the Utilities menu If you do not wish to initialize to this type of meter after all then press Gow key to return back to the Meter Selection menu If you do wish to initialize to this type of meter press the key to highlight the Y character CONDUCTIVITY Then press Gow
16. Press to view the next Calibration Data screen 1st POINT 600mV CALIBRATION DATA Probe Temperature at which CAL TEMP 19 4C calibration was performed lt 19 4 C If the Temperature Display Override is ON Section 5 10 the display will show CALIBRATION DATA TEMP O R ON NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Diagnostics Menu Calibration Data 5 12 Page 42 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Diagnostics Menu Sensor Input 5 13 500mV 25 0 RUN MODE The Sensor Input Menu allows the user to view real time uncompensated process data from the probe This is a Read only menu item DIAGNOSTICS Press to view the Sensor Input data PROBE 500mV The top line shows the mV input from the probe The bottom line shows the actual value of the TEMP 310 i TEMP 3310 temperature sensor in ohms If the Probe is not equiped with a NOTE Temperature Sensing Device PRESS THE AND KEYS and Temperature Display Override is ON Section 5 10 TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE the display will show PROBE 500mV TEMP O R ON ORP Diagnostics Menu Sensor Input 5 13 Page 43 MULTI PARAMETER TRANSMITTER USER S MANUAL ORP Output Menu 4 20mA Output 5 14 ETX The Transmitter has a single 4 20mA output electrically isolated from the ground The output can source current into a maximum of 800 ohms See Section 3 9 f
17. Section 2 Installation N 3 06 78 2 56 65 1 PANEL CUTOUT c Cee f FRONT VIEW Dwg N106 129 SIDE VIEW REAR VIEW Panel Mount The transmitters can be panel mounted to a panel using the hardware kit provided The panel cutout dimensions are shown in fig 2 1 and 2 2 Figure 2 3 Panel Mount EXTERNAL PANEL GASKET QTY 1 CUSTOMER SUPPLIED UNIVERSAL MOUNTING UNIVERSAL MOUNTING CLAMP QTY 2 1 4 20 X 2 1 2 QTYA SHARK17x Dwg N105 101 amp N105 104 Section 2 Installation EXTERNAL PANEL GASKET PANEL CUSTOMER SUPPLIED 5 4 Ch MULTI PARAMETER TRANSMITTER USER S MANUAL TX Section 2 Installation Surface Mount The SHARK7x be surface Figure 2 4 Surface Mount mounted using the hardware kit provided with the unit UNIVERSAL MOUNTING BRACKET QTY 1 Pipe Mount The SHARK 7x be mounted to a horizontal or vertical pipe with e a minimum outside diameter of 1 30 33mm for example 1 CPVC pipe and a maximum of 2 375 60mm for example 2 f CPVC pipe HOLES 91 4 FOR MOUNTING SCREWS QTYA CUSTOMER SUPPLIED DIN Rail Mount The SHARK can be DIN rail mounted or panel mounted See figure 2 3 amp figure 2 7 5 Fig 2 5 Vertical Pipe Mount MIN PIPE DIA 1 PIPE NOMINAL MAX PIPE DIA 2 PIPE NOMINAL 2 MIN PIPE DIA 1 NOMINAL MAX PIPE DIA 2 PIPE NOMINAL UNIVERSAL
18. This function is useful if you wish DOWN DOWN to view the current selection without making any changes Then press the key to store the selection and return to the T COMP OVERRIDE Menu Not stored pH Setup Menu T Comp Override 4 10 Page 23 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Setup Menu Display Damping 4 11 The Display Damping menu allows the user to adjust the rate at which the display and the output is Bown updated This allows the user to dampen out unstable process readings The damping can be set from 0 seconds to 10 Bown seconds default value is 0 sec TEMP SENSOR DOWN AUTO RETURN DOWN T COMP OVERRIDE Gown Press the 07 key once which will move the cursor over the seconds digit DISPLAY DAMPING 3 DAMPING zT UPDATE 05 DOWN DISPLAY DAMPING Use the and to adjust UPDATE gt the damping time the default setting is 0 seconds The setting can be adjusted from 0 to 10 seconds Press the 4 key once which will move the cursor back to the RH side of the display DISPLAY DAMPING UPDATE SEC gt DISPLAY DAMPING UPDATE 10 SEC Press the Gow key to accept the setting and move to the store function DOWN If you wish to save the setting press the G gt gt key to highlight the Y character With N selected pressing the Gow DISPLAY DAMPING PTS key will NOT store the selection but
19. UNTSOFTIME U SEC 7 5 side of the sensor or on a label E UE RUNS NTSOFTIME attached to the sensor cable 5 0 SEC 7 6 RESET TOTALIZER OTALIZER RESET TO ZERO SEC 7 0 K TOTAL RUN MODE Section 3 Electrical Connections and Setup Page 10 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K TX Section 3 Electrical Connections and Setup 3 10 MANUAL TEST MODE LCD MENU SECTIONS pH 4 4 ORP 5 3 Conductivity 6 4 Flow 7 2 The setup can be tested using Manual Test Mode to simulate process changes MANUAL TEST MODE is used to simulate a process reading in order to verify the correct response of the output 3 11 4 20 mA Isolated Output LCD MENU SECTIONS pH 4 15 ORP 5 14 Conductivity 6 16 Flow 7 14 The Transmitter has a single 4 to 20mA output electrically isolated from the ground The output can source current into a resistive load Maximum resistance depends on supply voltage Drawing on page 6 Fig 3 1 The output is dedicated to track the process and has fully independent and fully adjustable 4 amp 20 mA output setpoints This will enable the operator to span the output over the desired range The output can be precisely trimmed through the LCD menu for precision applications The drawing on page 6 Fig 3 1 shows the connections for the output Wire Specification 22 AWG 7 30 insulation 0 010 Section 3 Electrical Connections and Setup Page 11 M
20. Y character With N selected pressing the Gow TEMP UNIT TEMP UNIT key will NOT store the selection but STORE YN STORE simply return to the TEMP UNIT Selection Menu This function is useful if you wish to view the current selection Then press the Gown key to store the without making any changes Not stored selection and return to the TEMP UNIT Selection Menu NOTE PRESS THE C AND Gow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Setup Menu Temp Unit 5 6 Page 36 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Setup Menu Temp Sensor 5 7 TEMP SENSOR allows the user to select the type of temperature sensor used in the probe The factory default for ORP is a 300 NTC Thermistor The user can also select a 3000 NTC Thermistor or a 1000 RTD TEMP UNIT TEMP SENSOR TEMP SENSOR qp Press the key once 300 NIC which will move the cursor over to the sensor type Use the Cup or to select the sensor type TEMP SENSOR Once the correct Sensor has been selected press the G gt gt key once which will move the cursor back to the RH side of the display 1 000 2 RTD gt TEMP SENSOR 3000 2 NTC gt TEMP SENSOR 300 NTC Press the Gow key to accept the change and move to the store function Or press the Gr key to highlight the Y character TEMP SENSOR TEMP SENSOR With N selected pressing the TEMP SENSOR key will NOT store the
21. by the smallest digit Holding the key down will cause the to value change at an increasing rate until the key is released Pressing the key again will cause the value to start changing at it s Slowest rate again This allows the user to get to the new K Factor value quickly The K Factor can be set anywhere from 0 5000 pulses per U S Gallon to 1500 0 pulses per U S Gallon ETX MULTI PARAMETER TRANSMITTER USER S MANUAL Flow Calibration Menu K Factor 7 1 The K Factor menu is used to enter the flow sensor calibration factor The K Factor represents the number of pulses per U S Gallon generated by the combination of sensor and flow fitting It is normally stamped on the flow fitting or attached to a tag on the cable Typical K factors range between 0 5000 to K FACTOR 100 00 If you just wish to view the current K Factor without changing it press the Gow key which will move to the store function K FACTOR If the calibration did not appear to be correct press the Gow key which will return back to the K Factor menu without storing the value Flow Calibration Menu K Factor 7 1 To enter the K factor use the ow key to enter the Calibration menu and then the G gt gt key to select the K Factor menu Press the G gt gt key once which will move the cursor over the least sign digit of the display Use the u and keys to adjust the reading until it agrees with the actual K Factor as specif
22. correct Sensor has been selected press the key once which will move the cursor back to the RH side of TEMP SENSOR the display 1000 RTD gt TEMP SENSOR 300 NTC Press the key to accept the change and move to the store function Or press the key to highlight the Y character i TEMPSENSOR TEMP SENSOR With selected pressing the TEMP SENSOR TEMP SENSOR key will NOT store the selection but simply return to the TEMP SENSOR Selection Menu This function is useful if you wish to view the current selection without making any changes Then press the key to store the Not stored selection and return to the TEMP SENSOR Selection Menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Setup Menu Temp Sensor 4 8 Page 21 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Setup Menu Auto Return 4 9 AUTO RETURN is used to select what conditions will cause the controller to time out of the operations menu MENU ON will cause the controller to exit the menu and revert back to the online run mode after 10 minutes with no buttons pressed This feature ensures that if a user forgets to return back to run mode the controller will not be left in an offline state If for some reason the user would like to remain in the menu mode for extended periods of time the TEMP SENSOR AUTO RETURN function can be set to OFF D
23. menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Setup Menu Temp Comp Curve 6 12 Page 58 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K 7 Conductivity Diagnostics Menu Firmware Rev 6 13 The FIRMWARE REV menu allows the user to see what revision of the firmware is currently installed in the controller This is a Read Only menu item FIRMWARE REV NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Diagnostics Menu Firmware Rev 6 13 Page 59 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K 7 Conductivity Diagnostics Menu Calibration Data 6 14 The Calibration Data menu is a series of read only screens which allow the user to view the data collected during the last calibration Press to view the first Calibration Data screen TYPICAL DISPLAYS TYPCIAL DISPLAYS FOR MANUAL CAL FOR DRY CAL CALIBRATION DATA 1717 CALIBRATION DATA MODE 1PT point calibration MODE DRY ry Ca Press to view the next Press to view the next Calibration Data screen Calibration Data screen CALIBRATION DATA Conductivity of Buffer No Buffer used in 1P 1000 1000 2 Input Resistance this Calibration Mode CALIBRATION DATA Calculated Cell Constant CALIBRATION DATA Cell Constant Setting K FACTOR 0 9774 K FACTOR 1 0000 CALIBRATION DATA Probe Temperature at
24. of Time 7 5 The Units of Measurement is broken into two variables UNITS OF VOLUME and UNITS OF TIME The two variables are then combined to display the desired units of measure For example if units of Volume is to set Cubic Meters CM and Units of Time is set for Seconds S the controller will display flow as Cubic Meters per Second on the front LED display Press the Gr key once which will move the cursor SECONDS S over the last character of the time unit setting Use the keys to scroll through the available ranges UNITS OF TIME MINUTES M Press the key to accept the setting and move to the store function Or press the G gt gt key to highlight the Y character With N selected pressing the ow UNITS OF TIME key will NOT store the selection but simply return to the UNITS OF TIME Selection Menu This function is useful if you wish to view the current Then press the ow key to store the selection without making any Not stored Stored selection and return to the UNITS OF changes TIME Selection Menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Setup Menu Units of Time 7 5 Page 69 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Setup Menu Auto Return 7 6 RUN MODE AUTO RETURN is used to select what conditions will cause the controller to time out of the operations menu MENU ON will cause the cont
25. store the selection and return to the OUTPUT menu pH Output Menu 4 20mA Output 4 15 20mA TUNE 512 L pH Output Menu 4 20mA Output 4 15 The Transmitter has a single 4 20mA output electrically isolated from the ground The output can source current into a maximum of 800 ohms See Section 3 9 for wiring diagram The channel has a fully adjustable 4 amp 20 mA output adjustments This will enable the operator to span the output over the desired range The example below shows the 4 20 mA set to 4mA 7 00pH and 20mA 14pH The output would then span 4 to 20 mA for a pH swing of 7 0 to 14 0 Note that the span can reversed in that 4 mA can be set to a high pH value and 20 mA can be set to a low pH value effectively reversing the control direction If you wish to change the setting press the key once which will move the cursor to the first character of the value to be changed PIS 4mA OUT 0 0 0 gt Use the ve and keys to change the setting Press the 4 key once which will move the cursor back to the RH side of the display 4 20mA PROC 4mA OUT 700 gt 4 20mA PROC 4mA OUT 7 00 DOWN Press the key to accept the setting and move to the next If you wish to change the setting setting press the 4 amp key once which will move the cursor to the first character of the value to be changed 4 20mA PROC 20mA OUT 14 00 gt Use the ve and keys to change the setting
26. then press key to return back to the Meter Selection menu If you do wish to initialize to this type of meter press the G gt gt key to highlight the Y character FLOW INITIALIZE DOWN NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 67 TOTAL 0 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Setup Menu Units of Volume 7 4 The Units of Measurement is broken into two variables UNITS OF VOLUME and UNITS OF TIME The two variables are then combined to display the desired units of measure For example if units of Volume is to set Cubic Meters CM and Units of Time is set for Seconds S the controller will display flow as Cubic Meters per Second on the front LED display UNITS OF VOLUME The user can select from four predefined units of Volume or create their own custom value The four predefined units are US Gallons GP Cubic Feet CF Liters LP Cubic Meters CM The user can also select any two custom characters to represent units from AA to ZZ and an input multiplier which will numerically relate the custom unit of measure to US Gallons The input multiplier can be set at any value between 0 0001 and 10000 UNITS OF VOLUME UNITS OF VOLUME Press the G gt gt key once which will move the cursor UNITS OF VOLU US GALLONS WARNING Changing the units of Volume with an accumulated flow total will reset the flow total to zero UNITS OF VOLU
27. to their specific process Estimates of the correct compensation for certain chemicals are available and can be preset via this menu otherwise the user will need to set the compensation to 0 measure the effect of temperature for a specific process calculate the Gown actual compensation required and enter it through this menu The Compensation can be varied from 0 C to 10 C DOWN TEMP SENSOR DOWN AUTO RETURN DOWN T COMP OVERRIDE DOWN DISPLAY DAMPING DOWN TEMP COMP CURVE 4 COMP CURVE gt Press the G gt gt key once 2 0 which will move the cursor over the least digit TEMP COMP CURVE Use the and Gow to adjust the percent compensation The setting can be changed from 0 to 10 C TEMP COMP CURVE 2 15 gt Press the key once which will move the cursor back to the RH side of the TAPER 259 C Bown Press the key to accept the setting and move to the store function If you wish to save the setting press the key to highlight the Y character With N selected pressing the TEMP COMP CURVE key will NOT store the selection but STORE Y N simply return to the Temp Cond Curve setting menu This function is useful if you wish to view the current selection TEMP COMP CURVE without making any changes STORE N DOWN Then press the key to store the Not stored Stored selection and return to Temp Cond Curve settting
28. will report the measured value Press the key to move to Buffer 2 Place the probe in the second buffer solution Be sure to clean and rinse the Probe first with D I water and then insert it in the 4 00 buffer Press the key The controller will read the pH value averaging a number of results to get a stable calibration value Please wait for the controller to complete the measurement BUFFER ERROR CONTINUE When complete the controller will report the measured value After 5 seconds the controller will compute the slope of the calibration the estimated probe efficiency and the probe temperature If the calibration is OK use key to move the cursor over the Y text and press the down key AUTO CAL pH This will store the calibration data and return back to the Auto cal setup so the user can select another function NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 15 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt R K TX pH Calibration Menu Temperature Calibration 4 3 7 15pH 25 0C RUN MODE CALIBRATION 47 CAL pH DOWN AUTO CAL pH DOWN TEMP CALIBRATION 4 TEMP CALIBRATION 224 DOWN TEMP CALIBRATION TEMP CALIBRATION ok gt TEMP CALIBRATION TFACTOR SHIFTED Lo E If the calibration does not appear to TEMP CALIBRATION be correct press the key STORE YIN which will return b
29. 25 0C AUTO RETURN is used to select what conditions will cause the controller to time out of the operations menu MENU ON will cause the controller to exit the menu and revert back to the online run mode after 10 minutes with no buttons pressed This feature ensures that if a user forgets to return back to run mode the controller will not be left in an offline state If for some reason the user would like to TEMP UNIT remain in the menu mode for extended periods of time the AUTO RETURN function can be set to OFF DOWN DOWN TEMP SENSOR DOWN To change the MENU RETURN setting Press the key once AUTO RETURN 4 AUTO RETURN which will move the cursor to MENU the ON or OFF text DOWN Use the or keys to select either ON or OFF Press the key once which will move the cursor back to the RH side of the display Press the key to accept the change and move to the STORE function Or press the key to highlight the Y character With N selected pressing the AUTO RETURN AUTO RETURN key will NOT store the selection but STORE Y 1 STORE N simply return to the AUTO RETURN Selection Menu This function is useful if BONN DOWN Then press the key to store the selection and return you wish to view the current selection without making any changes Not stored Stored to the Auto Return Selection Menu NOTE PRESS THE C AND KEYS TOGE
30. 7pH Temperature should read the same as in 7pH 3 Place the probe in buffer 10pH Probe should read 160mV less then probe value at 7pH Temperature should read the same as in 7pH pH Diagnostics Menu Sensor Input 4 14 Page 27 MULTI PARAMETER TRANSMITTER USER S MANUAL ETX 4 20mA PROC 4mA OUT 0 00 DOWN NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE The TUNE fuction allows the user to precisely adjust the 4 20 ma output to compensate for any errors in the output circuitry Normally fine tuning the 4 20mA output is not necessary To make the adjustment place an accurate current meter in series with the 4 20 mA output with the appropriate loads connected When the TUNE menu is selected the controller puts 20 mA out the terminals Use the or keys to adjust 20mA output to get exactly 20 4 20mA PROC 20 14 00 DOWN The TUNE value can be adjusted over the range from 0 to 1000 these are unitless numbers used for tuning purposes only With N selected pressing the key will NOT store the selection but simply return to the OUTPUT Menu This function is useful if you wish to view the current selection without making any changes 4 20mA PROC zs STORE Y Or press the G gt gt key to highlight the Y character 4 20mA PROC DOWN Not stored ROM Stored 4 20mA PROC STORE N Gown Then press the key to
31. DOWN KE PROBE SELECT Use the Qu or keys to scroll through th bet ilable If using the 2 wire Combination Probe which 0 IFFERENTIAL In this case the user can select doesn t have a temperature sensor T COMP the 2 or 4 wire combination probe OVERRIDE must be set to ON and the actual the 5 wire differential probe probe temperature set through the T COMP OVERRIDE menu see sec 4 11 Once the correct probe type is selected move to the store function to save the selection which will move the cursor back to the RH side of the display PROBE SELECT COMBINATION DOWN Press the key to accept the setting and move to the store function ap NI Or press the key to highlight With N selected pressing the the Y ss he CA key will NOT store the selection but simply return to the PROBE SELECT PROBE SELECT PROBE SELECT Menu This function is useful if you YN sr STORE YIN wish to view the current selection without making any changes a Then press the key to store the Not stored Stored selection and return to the PROBE SELECT Menu Note Refer to Appendix A Probe Configuration Table NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Setup Menu Probe Select 4 6 Page 19 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Setup Menu Temp Unit 4 7 TEMP UNIT allows the user to select either Deg
32. EC 5 5 SEC 5 4 SELECT DEG C OR DEG F SEC 5 6 SELECT TYPE OF TEMP SENSOR SEC 5 7 ENABLE TIME OUT FROM MENU SEC 5 8 DISABLE TEMPERATURE DISPLAY ON LCD AND LED DISPLAYS SEC 5 9 SETUP DISPLAY AND OUTPUT RESPONSE TIME SEC 5 10 DISPLAY FIRMWARE REV FIRMWAVE REVISION SEC 5 11 DISPLAY PREVIOUS CALIBRATION DATA SEC 5 12 DISPLAY UNCALIBRATED PROBE DATA SEC 5 13 NOTE 2 PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Menu Overview 5 0 Page 30 MULTI PARAMETER TRANSMITTER USER S MANUAL If the calibration did not appear to be correct press the key which will return back to the Manual Cal menu ORP Calibration Menu Manual Calibrate 5 1 IF BUFFER READY PRESS DOWNO RUNNING MANU CAL BUFFER WAIT MANUAL CAL ORP BUFFER 500 gt MANUAL CAL ORP BUFFER 600 gt MANUAL CAL ORP BUFFER 600 BUFFER 600mV EMP 25 0C MANUAL CAL ORP TX ORP Calibration Menu Manual Calibrate 5 1 Place the probe in the buffer solution be sure to clean and rinse the Probe first with D I water and then insert it in the mV buffer Press The controller will read the mV value averaging a number of results to get a stable calibration value Please wait for the controller to complete the measurement When complete the controller will report the measured value Use the Qu and keys to adjust the reading until it agrees with t
33. ETER SEC 6 5 NOTE PRESS THE C AND Gow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE 4 20 mA OUTPUT SEC 6 16 Conductivity Menu Overview 6 0 Page 46 MULTI PARAMETER TRANSMITTER USER S MANUAL 7 Conductivity Calibration Menu Manual Calibrate 6 1 Manual Calibration is used to wet calibrate the cell This can be done with the cell installed in the process or with the cell suspended in a known buffer solution When calibrated In Process the actual conductivity is determined with a grab sample or a hand held meter and the value entered in the display When calibrated with buffers the cell is placed in a known buffer solution and the value of the buffer entered on the display In both cases make sure the cell has time to stabilize both in temperature and conductivity before entering any data Place the cell in the buffer solution The controller will read the Conductivity value averaging a number of results to get a stable MANUALCALCOND calibration value t Pressthe G key once which will move the cursor over the least sign digit of the display Use the and keys to adjust the reading until it agrees with the actual buffer conductivity value MANUAL CAL COND MANUAL CAL COND Then press G gt gt to move the cursor to the RH position MANUAL CAL COND 1000 u If the calibration is OK use the G gt gt key to move the cursor over the Y text and press the down key If
34. ITIALIZE YN e DOWN ICIONDUCTIVITY Press the key to initialize the controller as a Flow meter INITIALIZE Press the Gr key to Exit and return to the Utilities menu If you do not wish to initialize to this type of meter after all then press key to return back to the Meter Selection menu If you do wish to initialize to this type of meter press the 4 gt gt key to highlight the Y character OR _ INITIALIZE DOWN NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 34 MULTI PARAMETER TRANSMITTER USER S MANUAL TX ORP Setup Menu Probe Select 5 5 500mV 25 0C RUN MODE PROBE SELECT will allow the user to select whether the probe is a 2 or 4 wire combination probe or a 5 wire differential probe Press the 4 key once 5 SELECT 4 PROBE SELECT 4 which will move the cursor DIFFERENTIAL over the first character of the probe type DOWN Not PROBE SELECT Use the or keys to scroll through ote th be styl lable If using the 2 wire Combination Probe which DIFFERENTIAL prope In this case the user can select doesn t have a temperature sensor T DISP the 2 or 4 wire combination probe OVERRIDE must be set to ON and the actual the 5 wire differential probe probe temperature set through the T DISP OVERRIDE menu see sec 5 10 Once the correct style probe is selected move to
35. OWN DOWN AUTO RETURN alle 4 To change the MENU RETURN setting Gown Press the r key once which will move the cursor to the ON or OFF text Use F or keys to select either ON or OFF Press the key once which will move the cursor back to the RH side of the display Bown Press the Gow key to accept the change and move to the STORE function Or press the Gr key to highlight the Y character With N selected pressing the AUTO RETURN AUTO RETURN key will NOT store the selection but 5 4k simply return to the AUTO RETURN STORE Y STORE N Selection Menu This function is useful if Then press the key to you wish to view the current selection store the selection and return without making any changes to the Auto Return Selection Not stored Stored Menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Setup Menu Auto Return 4 9 Page 22 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Setup Menu T Comp Override 4 10 Temperature Compensation Override is used to manually set the actual probe or process temperature This is useful if the probe does not have a temperature sensor or if the process temperature is constant When the override is enabled the controller will use the selected temperature when performing temperature compensation calculations PROBE SELECTION DOWN TEMP UNIT DOWN TEMP SENSOR DOWN AUTO RET
36. THER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Setup Menu Auto Return 6 9 Page 55 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Setup Menu T Comp Override 6 10 Temperature Compensation Override is used to manually set the actual probe or process temperature This is useful if the probe does not have a temperature sensor or if the process temperature is constant When the override is enabled the controller will use the selected temperature when performing temperature compensation calculations COND RANGE DOWN TEMP UNIT DOWN TEMP SENSOR DOWN AUTO RETURN Gown Press the key once which will move the cursor to T COMP OVERRIDE lt gt T COMP OVERRIDE 25 the ON or OFF text COMPENSATE OFF OVERRIDE COMPENSATE OFF gt Use the C or keys to select either ON or OFF T COMP OVERRIDE COMPENSATE DIN Press the 4 key once which will move the cursor back to the RH side of the T COMP OVERRIDE COMPENSATE ON DOWN Press the ow key to accept the change and move to the Temperature Entry function The user can now enter the actual probe or process temperature T COMP OVERRIDE Press the key once TEMP 254C 3 7 which will move the cursor over the least significant digit Bown of the temperature display PRESS THE ans KEYS T COMP OVERRIDE D i TEMP 25 gt Usethe Qu and to TOGETHER TO GO IMMEDIATELY BACK TO adusi A Po iem RUN MODE wi
37. TI PARAMETER TRANSMITTER USER S MANUAL ETX RUN MODE TOTAL 0 4 UNITS OF VOLUME DOWN UNITS OF TIME DOWN AUTO RETURN DOWN DISPLAY DAMPING 3 DISPLAY DAMPING AY With N selected pressing the key will NOT store the selection but simply return to the Display Damping Menu This function is useful if you wish to view the current selection without making any changes Flow Setup Menu Display Damping 7 7 Flow Setup Menu Display Damping 7 7 The Display Damping menu allows the user to adjust the rate at which the display and the output is updated This allows the user to dampen out unstable process readings The damping can be set from 0 seconds to 10 seconds default value is 0 sec Press the G gt gt key once which will move the cursor over the seconds digit UPDATE 05 DOWN DISPLAY DAMPING UPDATE gt Use Q and ow to adjust the damping time the default setting is 0 seconds The setting can be adjusted from 0 to 10 seconds Press the 457 key once which will move the cursor back to the RH side of the display ISPLAY DAMPING UPDATE 1p 5 DISPLAY DAMPING UPDATE 10 SEC DOWN Press the key to accept the setting and move to the store function If you wish to save the setting press the 4 key to highlight the Y character DISPLAY DAMPING xr STORE Y DISPLAY DAMPING stoRe STORE N Then press the key to store the
38. TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 72 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K TX Flow Diagnostics Menu Firmware Rev 7 9 The FIRMWARE REV menu allows the user to see what revision of the firmware is currently installed in the controller This is a Read Only menu item FIRMWARE REV 40 gt PRESS THE AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Diagnostics Menu Firmware Rev 7 9 Page 73 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt R K TX Flow Diagnostics Menu Calibration Data 7 10 TOTAL 0 RUN MODE M The Calibration Data menu is a read only screen which allow the user to view the K factor entered during the last calibration DIAGNOSTICS Press 457 to view the first SERUORUM RUNE This screen shows the K factor CALIBRATION DATA entered during calibration K FACTOR 125 00 Press to return to the Calibration Data menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Diagnostics Menu Calibration Data 7 10 Page 74 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K TX Flow Diagnostics Menu Sensor Input 7 11 The Sensor Input Menu allows the user to view real time signals from the probe The display will show the current input pulse rate in Hz pulses per second DIAGNOSTICS Press G gt gt to view the Sensor In
39. ULTI PARAMETER TRANSMITTER USER S MANUAL TX Section 4 Using the Transmitter pH Mode 1 4 TURN SCREWS FOR SHARKTX ONLY LCD DISPLAY MAIN MENU INTERFACE SCREEN 2 LINE 16 CHARACTER ESL MM ENU PRESS DOWN toe ene UNIT OF MEASURE SHARK IS CONFIGURED FOR SIMPLE THREE BUTTON INTERFACE FOR FAST amp EASY SETUP REFER TO SECTIONS 4 0 TO 4 15 Section 4 Using the Transmitter in pH Mode Page 12 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Menu Overview 4 0 7 15pH 25 0C RUN MODE MANUAL CALIBRATE MANUAL CAL pH pH PROBE SEC 4 1 AUTO CALIBRATE pH PROBE SEC 4 2 CALIBRATE TEMP SENSOR IN pH PROBE SEC 4 3 SIMULATE PROCESS SELECT TYPE OF VERIFY OUTPUTS FROBE SELECT pH PROBE SEC 4 4 SEC 4 6 SELECT TYPE SELECT DEG C OR DEG OF METER SEC 4 7 SEC 4 5 SELECT TYPE OF TEMP SENSOR SEC 4 8 ENABLE TIME OUT FROM MENU SEC 4 9 TEMPERATURE SETUP FOR PROBE WITHOUT TEMP SENSOR SEC 4 10 SETUP DISPLAY AND OUTPUT RESPONSE TIME SEC 4 11 DISPLAY FIRMWAVE REVISION SEC 4 12 DISPLAY PREVIOUS CALIBRATION DATA SEC 4 13 DISPLAY UNCALIBRATED PROBE DATA SEC 4 14 4 20 mA OUTPUT SEC 4 15 NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Menu Overview 4 0 Page 13 This example shows a MANUAL calibration with buffers of 7pH amp 4pH When performing a manual calibration any two known buffer solutions can be used
40. URN DOWN Press the Gr key once which will move the cursor to T COMP OVERRIDE 4 T COMP OVERRIDE gt ON or OFF text COMPENSATE OFF DOWN T COMP OVERRIDE COMPENSATE gt T COMP OVERRIDE COMPENSATE gt Press the G key once which will move the cursor back to the RH side of the T COMP OVERRIDE display COMPENSATE ON DOWN Use or keys to select either ON or OFF Press the key to accept change and move to the Temperature Entry function The user can now enter the actual probe or process temperature Press the key once T COMP OVERRIDE 4 4 Which will move the cursor TEMP 254C over the least significant digit of the temperature display T COMP OVERRIDE TEMP 2508 gt Use the and ow to adjust the reading until it agrees with the known temperature of the NOTE probe or process PRESS THE C AND ww KEYS Press the 407 key once TOGETHER TO GO IMMEDIATELY BACK TO T COMP OVERRIDE which will move the cursor RUN MODE meme 357K gt back to the RH side of temperature display T COMP OVERRIDE TEMP 35 7C Press the key to accept the reading and move to the store function If you wish to save the setting press the key to highlight the Y character Vei T COMP OVERRIDE OVERRIDE wl Store the selection Du STORE Y STORE N simply return to the T Comp Override Menu
41. ack to the Temp Calibration menu DOWN pH Calibration Menu Temperature Calibration 4 3 If the Temperature Compensation Override is set to ON see section 4 11 the Shark cannot calibrate the temperature sensor This display will appear to alert the user to the condition TEMP CALIBRATION TEMP O R ON gt The controller displays the current probe temperature If this incorrect the controller can be adjusted to compensate 382 Press the key once which will move the cursor over the least sign digit of the temperature display Use the and to adjust the reading until it agrees with the known temperature of the probe Press the which will move the cursor back to the RH side of temperature display Press the key to accept the reading and move to the store function T FACTOR SHIFTED will be displayed for 5 seconds to indicate that the temperature sensor has been calibrated The Shark will then move to the store function TEMP CALIBRATION This will store the calibration data STORE and return back to the Temp Calibration setup so the user can DOWN select another function NOTE PRESS THE AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 16 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Utilities Menu Manual Test Mode 4 4 Manual Test Mode is used to simulate a process reading in order to verify the correc
42. ctivity readings If the user is unsure of the calibration test fixture then it would be best to leave the temperature calibration at it s factory setting Be sure to allow the temperature of the cell to stabilize before attempting to calibrate the temperature sensor this may take a significant amount of time as the sensor is buried behind a protective layer of epoxy which will cause some delay CALIBRATION 4 MANUAL CAL COND Ifthe Temperature Compensation Override is set to ON see section 6 11 the Shark cannot calibrate the temperature sensor This display will appear to alert the DRY CAL COND user to the condition DOWN TEMP CALIBRATION 4 TEMP CALIBRATION TEMP O R ON gt The controller displays the current probe temperature If this incorrect the controller can be TEMP CALIBRATION adjusted to compensate 224C RON Press the 4 key once which will move the cursor over the least significant digit of the temperature display DOWN TEMP CALIBRATION Use the and to adjust the reading until it agrees with the known temperature of the probe TEMPCALIBRATION CALIBRATION p he GE ress the G gt gt key once boce o which will move the cursor back to the RH side of temperature display tL Press the Gow key to accept the reading and move to the store function DOWN T FACTOR SHIFTED T FACTOR SHIFTED will be T displayed for 5 seconds to indicate that the temperature sensor
43. e and the reading until it agrees wii buffer pH value Then press Gr cursor to the RH posi Then press to store complete the Manual Calibra eys to adjust h the actual io move the ition he value and ion BUFFER2 After 5 seconds the controller will compute the slope of the calibration the estimated probe efficiency and the probe temperature SLOPE 61 22MV pH EFF 9596 24 8C If the calibration is OK use the Gr key to move the cursor over the Y text and press the down key If the calibration did not appear to be Press to store the calibration correct press ST Y which will return back to the Manual Cal menu data and return back to the Manual Cal menu so the user can select another function MANUAL CAL pH Y NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Calibration Menu Manual Calibrate 4 1 Page 14 MULTI PARAMETER TRANSMITTER USER S MANUAL RK TX RUN MODE CALIBRATION MANUAL CAL pH DOWN AUTO CAL pH 4 gt IF BUFFER1 READY PRESS DOWN DOWN RUNNING AUTO CAL BUFFER1 WAIT If an erros occurs the controller will indicate a BUFFER ERROR alarm This could be caused by using a defective buffer incorrect probe wiring defective probe Press to return to the Auto cal menu try to correct the problem and calibrate again or go to the diagnotics menus t
44. f a two wire pH probe is used which has no temperature sensor ensure that the Temp Comp Override is set to same tempera ture as the buffer before calibrating If a two wire ORP probe is used you can blank the Temp display with the T DISP OVERRIDE menu pH ORP METER SELECTION METER SELECTION SELECT COMBINATION PROBE SELECT COMBINATION PROBE PROBE SELECT RE PROBE SELECT 5 TWO WIRE PROBE WITH NO TEMP SENSOR TWO WIRE PROBE WITH NO TEMP SENSOR MANUAL CAL PH PH PROBE T COMP OVERRIDE MANUAL CAL PH ORP PROBE T DISP OVERRIDE SEC 4 1 MANUAL PROBE SEC 5 1 DISABLE TEMPERATURE TEMPERATURE SETUP DISPLAY 7 15pH 25 0C RUN MODE SEC 4 10 7 15pH 25 0C RUN MODE SEC 5 10 Section 3 Electrical Connections and Setup Page 8 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt R K TX Section 3 Electrical Connections and Setup 3 5 Conductivity Cell Contacting style connections and setup The drawing shows the connections for the Aquametrix Conductivity Cells Contacting style The cable should be run in a conduit seperate from the AC power wires and via a seperate conduit hole The cell cable length should not exceed 300ft 91 meters Figure 3 4 Connections for Conductivity Cells NOTE JUMPER Dwg N104 44 Once connnected step through the LCD menus to select the cell in the order shown The TEMP COMP CURVE setup default is 1 8 deg C This is accept able for most process appli cations If your process is s
45. has been calibrated The Shark will then move to the store function T the did i appear EMP CALIBRATION TEMP CALIBRATION This will store the calibration key which will return back tothe STORE STORE a Temp Calibration menu ON the can select another function NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Calibration Menu Temp Calibration 6 3 Page 49 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Utilities Menu Manual Test Mode 6 4 Manual Test Mode is used to simulate a process reading in order to verify the correct response of the output 10005 250 RUN MODE When in the Manual Test Mode the output is no longer placed on hold as it is when in the rest of the menu Press the Gr key once which will move the cursor over the least digit of the simulated process value Use the and keys to change the simulated process value The 4 20 mA output will follow the process value change The 4 20 mA output will track the change in process value TEST 13101 gt Press the key once to 14 4mA alls move the cursor to the RH side of the display TEST 1310 Press the key to return to the 14 4mA MANUAL TEST MODE menu E When the user exits the Manual Test Mode the 4 20mA output will remain in the Test Mode state until the operator enters the run mode The output will then revert back to the previous
46. hat the controller is configured for either pH ORP Conductivity or FLow Once selected the controller will initialize itself for the selected meter s functionality and move to run mode Press the 4 key to initialize the controller as a pH meter INITIALIZE YN 2 Press the 4 key to initialize the controller as an ORP meter OR INITIALIZE YN DOWN Press the Gr key to initialize the controller as a Conductivity meter CONDUCTIVITY INITIALIZE YN lt gt DOWN ICIONDUCTIVITY Press the Gr key to initialize the controller as a Flow meter FLOW FLOW INITIALIZE y N lt gt DOWN Press the X key to Exit and return to the Utilities menu If you do not wish to initialize to this type of meter after all then press key to return back to the Meter Selection menu If you do wish to initialize to this type of meter press the key to highlight the Y character INITIALIZE DOWN NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 18 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Setup Menu Probe Select 4 6 7 15pH 25 0 RUN MODE PROBE SELECT will allow the user to select whether the probe is a 2 or 4 wire combination probe or a 5 wire differential probe Press the 4 key once 4 3 PROBE SELECT lt gt PROBE SELECT gt which will move the cursor DIFFERENTIAL over the first character of the probe type
47. he C4 key once to TEST 500 ps4 move the cursor to the RH side 12 0mA of the display TEST 50 TEST 200 Press the ow key to return to the Sm MANUAL TEST MODE menu When the user exits the Manual Test Mode the 4 20mA output will remain in the Test Mode state until the operator enters the run mode The output will then revert back to the previous On line state NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Utilities Menu Manual Test Mode 5 3 Page 33 MULTI PARAMETER TRANSMITTER USER S MANUAL ETX 500mV 25 0C RUN MODE DOWN CALIBRATION DOWN UTILITIES 4 MANUAL TEST MODE To reset the controller back to all the factory default values reselect the current meter type Then press Gow The controller will initialize itself for a specific meter ORP Utilities Menu Meter Selection 5 4 ORP Utilities Menu Meter Selection 5 4 The Meter Selection menu is used to select the meter type that the controller is configured for either pH ORP Conductivity or FLow Once selected the controller will initialize itself for the selected meter s functionality and move to run mode Press the 4 key to initialize the controller as a pH meter INITIALIZE YN Ce Press the G gt gt key to initialize the controller as an ORP meter INITIALIZE DOWN Press the G gt gt key to initialize the controller as a Conductivity meter CONDUCTIVITY IN
48. he actual buffer mV value Then press to move the cursor to the RH position The controller will display the mV value and the probe temperature for 5 seconds If the T DISPLAY O R is enabled the display will show TEMP O R ON If the calibration is OK use the key to move the cursor over the Y text and press the down key Press Gow to store the calibration data and return back to the Manual Cal menu so the user can select another function NOTE PRESS THE C AND Gow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 31 CALIBRATION ETX MULTI PARAMETER TRANSMITTER USER S MANUAL MANUAL CAL ORP DOWN TEMP CALIBRATION 4r TEMP CALIBRATION 224C DOWN TEMP CALIBRATION TEMP CALIBRATION opc gt l TEMP CALIBRATION TFACTOR SHIFTED p E If the calibration did not appear to be correct press key which will return back to the Temp Calibration menu TEMP CALIBRATION STORE YN DOWN ORP Calibration Menu Temp Calibration 5 2 ORP Calibration Menu Temp Calibration 5 2 If the Temperature Display Override is set to ON see section 5 10 the Shark cannot calibrate the temperature sensor This display will appear to alert the user to the condition TEMP CALIBRATION TEMP O R ON Hom The controller displays the current probe temperature If this incorrect the controller can be adjusted to compensate 3 7 Press the key once
49. he damping time the default setting is 0 seconds The setting can be adjusted from 0 to 10 seconds Press the G gt gt key once which will move the cursor back to the RH side of the DISPLAY DAMPING UPDATE gt DISPLAY DAMPING UPDATE 10 SEC Press the Gow key to accept the setting and move to the store function DOWN If you wish to save the setting press the key to highlight the Y character With selected pressing the DISPLAY DAMPING key will NOT store the selection but STORE Y NI 4 simply return to the Display Damping Menu This function is useful if you wish GOWN to view the current selection without DISPLAY DAMPING making any changes STORE N Then press the Gow key to store the Not stored selection and return to the Display Damping Menu NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Setup Menu Display Damping 6 11 Page 57 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K TX Conductivity Setup Menu Temp Comp Curve 6 12 The Temperature Compensation Curve setting allows the user to select the temperature compensation to match a specific process The variation of Conductivity versus Temperature is dependent on the type of solids and liquids in water so no fixed compensation value will accurately compensate every process This setting allows the user to fine tune the compensation
50. ied on the sensor Then press G gt gt to move the cursor to the RH position Press the key to accept the change and move to the store function If the K Factor setting is OK use the Gr key to move the cursor over the Y text and press the down key K FACTOR Press to store the calibration data and return back to the menu so the user can select another function NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 65 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Utilities Menu Manual Test Mode 7 2 Manual Test Mode is used to simulate a process reading in order to verify the correct response of the output When in the Manual Test Mode the output is no longer 20 placed on hold as it is when the rest of the menu TEST 50 00 GPM Press G gt gt key once which will move the cursor over the least digit of the simulated process value TEST 50 0 Use the and ow keys to change 120mA the simulated process value UP TEST 65 0 14 4mA The 4 20 mA output will follow the process value change The 4 20 mA output will track the change in process value TEST 65 0 0 gt Press key once to 144 3 7 move the cursor to the RH side of the display TEST 65 00 GPM 144m Press the key to return to the Am MANUAL TEST MODE menu When the user exits the Manual Test Mode the 4 20mA output will remain
51. ignificantly different from this change the setting in the TEMP COMP CURVE menu WHITE CELL 8 STANDARD ow CONTACTING MUST BE SET TO STANDARD CONDUCTIVITY CELL SELECT COND METER METER SELECTION mn SELECT CONDUCTIVITY RANGE COND RANGE SET ENSURE SENSOR IS CORRECT TYPE TEMP SENSOR 3Kohm NTC thermistor 1Kohm RTD SEC 6 9 SET TEMPERATURE COMPENSATION TEMP COMP CURVE FOR PROCESS SEC 6 13 OR CALIBRATE WITH CALIBRATE WITH FACTORY MANUAL CAL COND REFERENCE SOLUTIONS DRY CAL COND SPECIFIED CELL CONSTANT SEC 6 1 SEC 6 2 1000uS 25 0C RUN MODE Section 3 Electrical Connections and Setup Page 9 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K Section 3 Electrical Connections and Setup 3 6 Paddle Wheel Flow Sensor connections and setup The drawing shows the connnections for a typical paddle wheel flow sensor The cable to the sensor should not exceed 2000 600 meters Figure 3 5 Connections for Flow Sensor SHIELD SHIELD SIGNAL 5 SIGNAL 5 SHIELD IF AVAILABLE 6 52 2 2 5 FLOW SENSOR FLOW SENSOR Ep EXTERNAL POWERED SELF POWERED jow O00000 NOTE JUMPER MUST BE SET TO FLOW Dwg N104 45 Once connected step through the LCD menus to select the METERSELECTION geo METER SELECTION sensor in the order shown The 2 Sensor K factor pulses per U S Hen xS Gallon is usually printed on the OF VOLUME
52. in series with the 4 20 mA output with the appropriate loads connected When the TUNE menu is selected the controller puts 20 mA out the terminals Use the or keys to adjust the 20mA output to get exactly 20 The TUNE value can be adjusted over the range from 0 to 1000 these are unitless numbers used for tuning purposes only With N selected pressing the Gow key will NOT store the selection but simply return to the OUTPUT Menu This function is useful if you wish to view the current selection without making any changes 4 20mA PROC STORE Y Not stored Or press the key to highlight the Y character 4 20mA PROC DOWN 4 20mA PROC DOWN 4 DOWN Stored 4 20mA PROC STORE N Then press the key to store the selection and return to the OUTPUT menu Conductivity Output Menu 4 20mA Output 6 16 20mA OUT 2000 ER 20mA TUNE 512 lt r Conductivity Output Menu 4 20mA Output 6 16 The Transmitter has a single 4 20mA output electrically isolated from the ground The output can source current into a maximum of 800 ohms See Section 3 9 for wiring diagram The channel has a fully adjustable 4 amp 20 mA output adjustments This will enable the operator to span the output over the desired range The example below shows the 4 20 mA set to 4mA 400 uS and 20mA 1800 uS The output would then span 4 to 20 mA for a conductivity swing of 400 to 1800 Note that the span can
53. in the Test Mode state until the operator enters the run mode The output will then revert back to the previous On line state NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Utilities Menu Manual Test Mode 7 2 Page 66 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Utilities Menu Meter Selection 7 3 K RUN MODE TOTAL 0 DOWN CALIBRATION DOWN UTILITIES 4 MANUAL TEST MODE To reset the controller back to all the factory default values reselect the current meter type Then press The controller will initialize itself for a specific meter Flow Utilities Menu Meter Selection 7 3 The Meter Selection menu is used to select the meter type that the controller is configured for either pH ORP Conductivity or FLow Once selected the controller will initialize itself for the selected meter s functionality and move to run mode Press the G gt gt key to initialize the controller as a pH meter INITIALIZE YN Ce Press the key to initialize the controller as an ORP meter OR INITIALIZE YN DOWN Press the key to initialize the controller as a Conductivity meter CONDUCTIVITY INITIALIZE YN e DOWN ICJONDUCTIVITY Press the key to initialize the controller as a Flow meter INITIALIZE Press the Gr key to Exit and return to the Utilities menu If you do not wish to initialize to this type of meter after all
54. ion 3 Electrical Connections and Setup Page 6 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt R K TX Section 3 Electrical Connections and Setup 3 3 pH and ORP Differential Probe connections and setup The drawing shows the connections for the Aquametrix Differential 5 wire probe The cable should be run in a conduit separate from AC power wires and via a separate conduit hole Figure 3 2 Connections for Differential 5 wire pH or ORP probe YELLOW 10 O O00000 NOTE JUMPER MUST BE SET TO STANDARD DIFFERENTIAL Dwg N104 42 pH or ORP PROBE Once connected step through the LCD menus to ture correctly for accurate temperature compensa tion The ORP probe does not require temperature compensation although the transmitter can dis play process temperature measured by the probe The factory temperature calibration is usually accurate enough that no adjustments are neces sary or ORP PROBE SEC 5 1 select the probe in the order shown The first two METER SELECTION SELECT pH SEC 48 steps may be skipped if the meter is already con IF NECESSARY figured for pH or ORP and a Differential Probe PROBE SELECT SELECT DIFFERENTIAL PROBE When using a pH probe it is important to ensure that the transmitter is reading the probe tempera MANUAL CALIBRE pH PROBE SEC 4 1 7 15pH 25 0 RUN MODE Section 3 Electrical Connections and Setup Page 7 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt
55. ion without making any STORE YN STORE changes Then press the key to store the selection and return to the COND Not stored Stored RANGE Menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Setup Menu Conductivity Range 6 6 Page 52 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Setup Menu Temp Unit 6 7 TEMP UNIT allows the user to select either Degrees Centigrade or Fahrenheit units for display TEMP UNIT TEMP UNIT Press the G gt key once DEG C E 5 7 which will move the cursor over the unit type C or F Use Qu or to select or F TEMP UNIT Press the which will move the cursor back to the RH side of the display TEMP UNIT Press the key to accept the change and move to the store function Orpressthe 4 key to highlight the Y character With N selected pressing the key will NOT store the selection but simply return to the TEMP UNIT Selection Menu This function is useful if you wish to view the current selection Then press the key to store the without making any changes Not stored selection and return to the TEMP UNIT Selection Menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Setup Menu Temp Unit 6 7 Page 53 MULTI PARAMETER TRANSMITTER USER S MANUAL ETX TEMP UNIT TEMP SENSOR
56. isplay Then press the key to store the selection and return to the OUTPUT menu ORP Output Menu 4 20mA Output 5 14 Page 44 MULTI PARAMETER TRANSMITTER USER S MANUAL lt gt K 7 Section 6 Using the Transmitter in Conductivity Mode 1 4 TURN SCREWS FOR SHARKTX ONLY pe 2 LINE 16 CHARACTER 1000us 25 0C MAIN MENU INTERFACE MEASURE SHARK IS SCREEN CONFIGURED FOR LCD DISPLAY J M E N UIPRESS DO NO ENTE UNIT OF SIMPLE THREE BUTTON INTERFACE FOR FAST amp EASY SETUP REFER TO SECTIONS 6 0 TO 6 16 Section 6 Using the Transmitter in Conductivity Mode Page 45 MULTI PARAMETER TRANSMITTER USER S MANUAL ETX 1000uS 25 0C FIRMWARE REV COND RANGE DISPLAY FIRMWAVE REVISION SEC 6 13 DISPLAY PREVIOUS CALIBRATION DATA SEC 6 14 DISPLAY UNCALIBRATED PROBE DATA SEC 6 15 Conductivity Menu Overview 6 0 MANUAL CAL COND SELECT MEASURING RANGE SEC 6 6 SELECT DEG C OR DEG F SEC 6 7 SELECT TYPE OF TEMP SENSOR SEC 6 8 ENABLE TIME OUT FROM MENU SEC 6 9 TEMPERATURE SETUP FOR PROBE WITHOUT TEMP SENSOR SEC 6 10 SETUP DISPLAY AND OUTPUT RESPONSE TIME SEC 6 11 SETUP TEMP COMPENSATION VALUE SEC 6 12 CALIBRATE PROBE WITH BUFFER SOL N SEC 6 1 CALIBRATE PROBE WITH MANUFACTURER S DATA SEC 6 2 CALIBRATE TEMP SENSOR IN PROBE SEC 6 3 SIMULATE PROCESS VERIFY OUTPUTS SEC 6 4 SELECT TYPE OF M
57. lay Press the key to accept the setting and move to the next setting Page 62 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Section 7 Using the Transmitter in Flow Mode 1 4 TURN SCREWS FOR SHARKTX ONLY 2 LINE 16 CHARACTER e i W 0 LCD DISPLAY E N UIPRESS DO GATE UNIT OF MAIN MENU INTERFACE SCREEN MEASURE SHARK IS CONFIGURED FOR SIMPLE THREE BUTTON INTERFACE FOR FAST amp EASY SETUP REFER TO SECTIONS 7 0 TO 7 14 Section 7 Using the Transmitter in Flow Mode Page 63 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Menu Overview 7 0 RUN MODE Eg M DR KEACTOR CALIBRATION FACTOR SEC 7 1 SIMULATE PROCESS VERIFY OUTPUTS SEC 7 2 SELECT TYPE OF METER SEC 7 3 SETUP OF UNITS UNITS OF VOLUME OF VOLUME SEC 74 SETUP OF UNITS OF TIME SEC 7 5 ENABLE TIME OUT FROM MENU SEC 7 6 SETUP DISPLAY AND OUTPUT RESPONSE TIME SEC 7 7 RESET TOTALIZER TO ZERO SEC 7 8 FIRMWARE REV Y RMWAVE REVISION EC 7 9 SPLAY PREVIOUS ALIBRATION DATA EC 7 10 SPLAY UNCALIBRATED ENSOR INPUT EC 7 11 SPLAY PERMANENT OTALIZER EC 7 12 DISPLAY TOTALIZER ROLLOVERS TO DATE SEC 7 13 4 20 OUTPUT NOTE SEC 7 14 PRESS THE C AND ow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Menu Overview 7 0 Page 64 NOTE ACCELERATOR KEYS Pressing the Ce or key once will change the value
58. light the Y character With selected pressing the AUTO RETURN AUTO RETURN key will NOT store the selection but 7 4 simply return to the AUTO RETURN STORE STORE N Selection Menu This function is useful if BOWN BOWN you wish to view the current selection without making any changes Then press the key to store the selection and return to the Auto Return Selection Menu Not stored Stored NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Setup Menu Auto Return 5 8 Page 38 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Setup Menu Temp Display Override 5 9 T Display Override is used to blank the Temperature Display on the LCD menu and place 4 dots on the LED menu when Temp display is requested This is to ensure the user isn t shown a temperature value that isn t valid PROBE SELECTION DOWN TEMP UNIT DOWN TEMP SENSOR DOWN AUTO RETURN Gown Press the key once which will move the cursor to T DISP OVERRIDE 45 7 DISP OVERRIDE the ON or OFF text OVERRIDE OFF DOWN T DISP OVERRIDE OVERRIDE gt Use the or keys to select either ON or OFF T DISP OVERRIDE OVERRIDE gt Press key once which will move the cursor back to the RH side of the T DISP OVERRIDE display OVERRIDE Gown Press the key to accept the change and move to the store functi
59. o test the probe see Section 4 16 AUTO CAL pH This example shows an AUTO calibration with buffers of 7pH amp 4pH When performing an auto calibration any two standard buffers of 4 00 7 00 or 10 00 pH can be used The buffers will be automatically recognized if the probe measures them within 1 pH of their nominal value IF BUFFER2 READY PRESS DOWN RUNNING AUTO CAL B UFFER2 WAIT If an erros occurs the controller will indicate a BUFFER ERROR alarm This could be caused by using the same buffer twice using a defective buffer incorrect probe wiring defective probe Press C4 K to return to the Auto cal menu try to correct the problem and calibrate again or go to the diagnotics menus to test the probe AUTO CAL pH BUFFER2 4 005 SLOPE 61 22MV pH EFF 9596 24 8C If the calibration did not appear to be correct press the Gown key which will return back to the Auto cal menu AUTO CAL pH pH Calibration Menu Auto Calibrate 4 2 pH Calibration Menu Auto Calibrate 4 2 Place the probe in the first buffer solution be sure to clean and rinse the Probe first with D I water and then insert it in the 7 00 buffer Press Gown The controller will read the pH value averaging a number of results to get a stable calibration value Please wait for the controller to complete the measurement BUFFER ERROR CONTINUE When complete the controller
60. of the key to highlight 4 20mA PROC display Stored the Y character 20mA TUNE 540 Bown Press the ow key to accept the 4 20mA PROC setting and move to the next setting STORE Then press the Gow key to store the selection and return to the OUTPUT menu With N selected pressing the Not stored Flow Output Menu 4 20mA Output 7 14 Page 78 MULTI PARAMETER TRANSMITTER USER S MANUAL Appendix A Probe Configuration Table Appendix A Probe Configuration Table Page 79 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Return Policy amp Warranty Plan AQUAMETRIX INC RETURN POLICY Contact Aquametrix for a Return Material Authorization RMA form amp number This RMA number is required for all returns or they will not be accepted The RMA number must be written on the outside of the box for proper identification A copy of the RMA form along with a description of the problem model amp serial number must be attached with the returning item s All C O D freight collect shipments will be refused unless authorized by AquaMetrix Shipping documents must indicate RETURNING FOR REPAIR ONLY NO COMMERCIAL VALUE 12 MONTH AQUAMETRIX WARRANTY REPLACEMENT PLAN AquaMetrix Inc will replace or repair AquaMetrix SHARKrx SHARK re transmitter that fails due to defects in material or workmanship for a period of up to 12 months from the date of shipment from our facility
61. on If you wish to save the setting press the GF key to highlight the Y character key wil NOT store tne sehn bu T simply return to the T Disp Override YN STORE Menu This function is useful if you wish DOWN DOWN to view the current selection without making any changes Then press the ow key to store the selection and return to the T DISP OVERRIDE Menu Not stored NOTE PRESS THE Cv AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Setup Menu Temp Display Override 5 9 Page 39 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Setup Menu Display Damping 5 10 500mV 25 0C RUN MODE The Display Damping menu allows the user to adjust the rate at which the display and the output is updated This allows the user to dampen out unstable process readings The damping can be set from 0 seconds to 10 Bown seconds default value is 0 sec TEMP SENSOR DOWN AUTO RETURN DOWN T DISP OVERRIDE Gown Press the G gt gt key once which will move the cursor over the seconds digit DOWN DISPLAY DAMPING lt gt gt DISPLAY DAMPING 2 UPDATE 05 DOWN DISPLAY DAMPING Use the Cur and to adjust UPDATE OSEC gt the damping time the default setting is 0 seconds The setting can be adjusted from 0 to 10 seconds Press 4 key once NOTE which will move the cursor back PRESS THE Q AND KEYS to the RH side of the display TOGETHER TO
62. or wiring diagram The channel has a fully adjustable 4 amp 20 mA output adjustments This will enable the operator to span the output over the desired range The example below shows the 4 20 mA set to 4mA 200mV and 20mA 800 The output would then span 4 to 20 mA for a mV swing of 200mV to 800mV Note that the span can be reversed in that 4 mA can be set to a high mV value and 20 mA can be set to a low mV value effectively reversing the control direction If you wish to change the setting press the key once which will move the cursor to the first character of the value to be changed 4 20mA PROC TS 4 20mA PROC 4mA OUT 0 00 4mA OUT 0 CORN G Use the Cur and keys to change the setting 4 20mA PROC 4mA OUT 200 gt Press the G gt gt key once which will move the cursor back to the RH side of the display NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE 4 20mA PROC 4mA OUT 200 OWN Press the key to accept the setting and move to the next If you wish to change the setting setting The TUNE fuction allows the user to precisely adjust the 4 20 ma output to compensate for any errors in the output circuitry Normally fine tuning the 4 20mA output is not necessary To make the adjustment place an accurate current meter in series with the 4 20 mA output with the appropriate loads connected When the TUNE menu is selected the controller puts 20 mA out the terminals
63. put data FREQ 101 Hz Press to return to the menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Diagnostics Menu Sensor Input 7 11 Page 75 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Diagnostics Menu Permanent Total 7 12 TOTAL 0 The Permanent Total is a running total of all the volume units that have been accumulated by the controller It starts at zero when new and can only be set to zero at the factory This is a read only screen Press F to view the Total Life Flow to date TOTAL LIFE FLOW Press Ow to return to the 72143 j e NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Diagnostics Menu Permanent Total 7 12 Page 76 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Diagnostics Menu Total Rollover 7 13 RUN MODE The Total Rollover menu is another read only screen It is used to indicate how many times the Permanent and Resetable Totalizers have rolled over during the life of the controller DIAGNOSTICS PER indicate the number of times the Permanent Totalizer has rolled over RST indicates the number of times the Resetable Totalizer has rolled over Press G gt gt to view the Totalizer Rollovers to date TOTAL ROLLOVER Press to return to the menu NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Diagnostics Menu To
64. r then press the key to move to the left hand text character CUSTOM gt milliliters Again use P keys to select the appropriate text character then press the 47 key to move the cursor to the RH position UNITS OF VOLUME CUSTOM ML gt Press the key to accept the setting and move to the custom multiplier setting Press the 4 key once which will move the cursor over the smallest digit of the custom multiplier UNITS OF VOLUME CUSTOM 1 000 0 UP CUSTOM 1 0000 UNITS OF VOLUME CUSTOM 3785 4 With N selected pressing the Gow key will NOT store the selection but simply return to the UNITS OF VOLUME Menu This function is useful if you wish to view the current selection without making any changes Not stored Flow Setup Menu Units of Volume 7 4 UNITS OF VOLUME STORE Use the CUP or Gow keys to select the correct multiplier When complete press the Q key to move the cursor to the RH position Units of Volume and UNITS OF VOLUME ue 37854 COR key accepi DOWN the setting and move to the store function Setting the custom Or press the key to highlight the Y character UNITS OF VOLUME STORE Then press the key to store the selection and return to the UNITS OF VOLUME menu Stored Page 68 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Setup Menu Units
65. rees Centigrade or Fahrenheit units for display Press 4 key once which will move the cursor over the unit type C or F TEMP DEGREE Use Qu to select or F TEMP UN Press the 457 key once DEGREE which will move the cursor back to the RH side of the display TEMP UNIT DEGREE RI Press the key to accept the change and move to the store function Or press the Gr key to highlight the Y character With N selected pressing the Gow TEMP UNIT TEMP UNIT key will NOT store the selection but STORE YN STORE simply return to the TEMP UNIT Selection Menu This function is useful if you wish to view the current selection Then press the key to store the without making any changes Not stored selection and return to the TEMP UNIT Selection Menu NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Setup Menu Temp Unit 4 7 Page 20 MULTI PARAMETER TRANSMITTER USER S MANUAL TX pH Setup Menu Temp Sensor 4 8 TEMP SENSOR allows the user to select the type of temperature sensor used the in the probe The factory default for pH is a 3000 NTC Thermistor The user can also select a 3000 0 NTC Thermistor or a 1000 RTD TEMP SENSOR Ap Press the G gt gt key once 3000 NTC which will move the cursor over to the sensor type Use the CUP to select the sensor type TEMP SENSOR 3100 NTC gt the
66. reversed in that 4 mA can be set to a high conductivity value and 20 mA can be set to a low conducivity value effectively reversing the control direction If you wish to change the setting press the key once which will move the cursor to the first character of the value to be changed 4 20mA PROC 4mA OUT lo gt Usethe and Cow keys to change the setting 4 20mA PROC 4mAOUT 400 4 20mA PROC 4mAOUT 400 DOWN Press the 47 key once which will move the cursor back to the RH side of the display Press the Gown key to accept the setting and move to the next setting If you wish to change the setting press the G gt gt key once which will move the cursor to the first character of the value to be changed 4 20mA PROC 20mAOUT 2001 gt Use CuP gt and Gow keys to change the setting 4 20mA PROC 20mAOUT 1800 gt 4 20mA PROC 20mAOUT 1800 DOWN Press the 4 key once which will move the cursor back to the RH side of the display Press the key to accept the setting and move to the next setting If you wish to change the setting press the 4 key once which will move the cursor to the first character of the value to be changed 4 20mA PROC 20mA TUNE 51D gt Use the and ow keys to change the setting 4 20mA PROC 20mA TUNE 540 gt 4 20mA PROC 20mA TUNE 540 DOWN Press the 07 key once which will move the cursor back to the RH side of the disp
67. robe tag DRY CALIBRATION K FACTOR 10 00 0 gt Then press G gt to move the cursor to the RH position DRY CALIBRATION K FACTOR 10 000 If the setting is OK use key to move the cursor over the Y text and press the down key If the calibration did not appear to be correct press the Gout key which will return back to the Manual Cal Cond menu DRY CALIBRATION Press to store the calibration data and return back to the Dry Cal Cond menu so the user can select Conductivity Calibration Menu Dry Cal Cond 6 2 another function NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 48 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Calibration Menu Temp Calibration 6 3 Temperature Calibration In most cases the factory temperature calibration is accurate enough to ensure correct temperature readings However in some circumstances the user may wish to ensure the temperature sensor is calibrated accurately especially when operating at the extreme end of the conductivity cell temperature operating range or where the temperature compensation is critical to correct process readings This menu allows the user to calibrate the temperature anywhere within it s range Be aware that the conductivity reading is affected by the temperature reading due to the temperature compensation so accurate temperature calibration is vital to obtaining accurate condu
68. roller to exit the menu and revert back to the online run mode after 10 minutes with no buttons pressed This feature ensures that if a user forgets to return back to run mode the controller will not be left in UNITS OF VOLUME an offline state If for some reason the user would like to DOWN remain in the menu mode for extended periods of time the UNITS OF TIME AUTO RETURN function can be set to OFF Gown To change the MENU RETURN setting AUTO RETURN lt RETURN Press the gt key once MENU ON 4 gt which will move the cursor to the ON or OFF text DOWN AUTO RETUR Use the keys to select either ON or OFF AUTO RETUR MENU Dr Press the G once which will move the cursor back to the AUTO RETUR RH side of the display MENU OFF Bown Press the key to accept the change and move to the STORE function Or press the Gr key to highlight the Y character With N selected pressing the AUTO RETURN AUTO RETURN key will NOT store the selection but STORE YN 5 STORE simply return to the AUTO RETURN Then press the key to Selection Menu This function is useful if SOWN store Wo you wish to view the current selection to the Auto Return Selection without making any changes Menu Not stored Stored NOTE PRESS THE AND ow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Flow Setup Menu Auto Return 7 6 Page 70 MUL
69. selection but STORE Y N STORE simply return to the TEMP SENSOR Selection Menu This function is useful if you wish to view the current selection without making any changes Then press the ow key to store the Not stored Stored selection and return to the TEMP SENSOR Selection Menu NOTE PRESS THE C AND Cow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Setup Menu Temp Sensor 5 7 Page 37 MULTI PARAMETER TRANSMITTER USER S MANUAL TX ORP Setup Menu Auto Return 5 8 AUTO RETURN is used to select what conditions will cause the controller to time out of the operations menu MENU ON will cause the controller to exit the menu and PROBE SELECTION revert back to the online run mode after 10 minutes with no RON buttons pressed This feature ensures that if a user forgets to return back to run mode the controller will not be left in an offline state If for some reason the user would like to remain in the menu mode for extended periods of time the TEMPSENSOR i TEME SENSOR AUTO RETURN function can be set to OFF DOWN gt T RETURN setting Bown Press the key once which will move the cursor to the ON or OFF text DOWN Use the C or keys to select either ON or OFF Press the G gt gt key once which will move the cursor back to the RH side of the display Gown Press the key to accept the change and move to the STORE function Or press the key to high
70. selection and return to the Display Stored Damping Menu Not stored NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 71 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Setup Menu Totalizer Reset 7 8 TOTAL 0 Totalizer Reset is used to reset the Flow totalizer to zero Note that once complete this action cannot be reversed The accumulated total will be erased permanently UNITS OF VOLUME DOWN UNITS OF TIME DOWN AUTO RETURN DOWN DISPLAY DAMPING DOWN If you wish to reset the totalizer press the TOTALIZER RESET key to highlight the Y character RESET Y TOTALIZER RESET 4 DOWN TOTALIZER RESET RESET N then Press the key to confirm the action If you do not wish to reset the totalizer Press the Gow key which will return back to the Totalizer Reset menu TOTALIZER RESET PI CONFIRM YN If you do not wish to reset the totalizer DOWN The controller will ask once more If you wish to reset the totalizer press the key to highlight the Y character Press the key which will return TOTALIZER RESET back to the Totalizer Reset menu CONFIRM then Press the key to complete the action TOTALIZER RESET Flow Setup Menu Totalizer Reset 7 8 The controller will confirm the action and return back to the Totalizer Reset menu NOTE PRESS THE AND KEYS
71. splay damping of unstable process Net Weight 0 71 Ibs 0 32 kg 5 0 25 Ibs 0 12 kg Approvals ULC pending Section Specifications Page 2 Ch MULTI PARAMETER TRANSMITTER USER S MANUAL TX Section 2 Installation 2 1 Unpacking Save the shipping carton and packing material in case the instrument needs to be stored or returned Inspect the instrument and packing material for shipping damage and report any problems immediately 2 2 Location Locate the transmitter close to the sensor The list below gives typical maximum distances for various sensors Refer to the sensor specifications for exact information Aquametrix Differential PH Probe Aquametrix Combination PH Probe Aquametrix Conductivity Probe Aquametrix Flow sensor 2 3 Mounting Fig 2 1 SHARK7x Transmitter dimensions MOUNTING BRACKET 1 45 37 MINIMUM INTERIOR CLEARANCE 3 80 FOR PANEL 97 _ MOUNTING 2 79 TOP VIEW 71 mE inches FRONT VIEW SIDE VIEW Dwg N106 128 Section 2 Installation 3000 ft 914 meters 10 ft 3 meters 300 ft 91 meters 2000 ft 610 meters 3 91 60 PANEL CUTOUT 00 26 07 4PLCS MOUNTING BRACKET Page 3 MULTI PARAMETER TRANSMITTER USER S MANUAL ETX Fig 2 2 SHARK7xP Transmitter dimensions p 0 75 19 MINIMUM 1 INTERIOR CLEARANCE FOR PANEL MOUNTING 0 75 inches 19 mm TOP VIEW
72. splay the meter selection screen where the meter type must be selected refer to section 4 5 Meter Selection This meter selection screen will only be displayed when the Shark is powered up for the first time After the user selects a meter type the Shark will remain set to that meter type until it is changed with the meter selection menu function in the Utilities menu To return the Shark to its factory settings the user must re select the current meter type from the meter selection menu function This will override all set points and return all settings back to the factory settings The Shark Users menu has been divided into five main categories Calibration used to calibrate the Shark with the selected sensor Utilities used to manually control or override the outputs Setup used to configure the Sharks many options Diagnostics used to troubleshoot problems with the Shark or sensor Outputs used to configure the Shark s 4 to 20mA output SHARK xis packaged a rugged NEMA 4X polycarbonate enclosure with a universal mounting kit for surface panel and pipe mount applications This enclosure is perfect for stand alone or panel mount operation SHARK rxe enclosure is also polycarbonate with a NEMA 4X front panel Panel mount and DIN rail mounting hardware are supplied Introduction Page 1 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Section Specifications pH ORP Conductivity Flow Display 2 x 16 alpha n
73. t response of the output 7 15pH 25 0C RUN MODE When in the Manual Test Mode the output IS no longer placed on hold as it is when in the rest of the menu Press the 07 key once which will move the cursor over the least digit of the simulated process value Use and keys to change the simulated process value 19 0mA The 4 to 20 mA output will follow the process value change The 4 20 mA output will track the change in process value Press the key once to 13 15 move the cursor the RH side T 19 0 of the display TEST 1315 Press the key to return to the MANUAL TEST MODE menu When the user exits the Manual Test Mode the 4 20mA output will remain in the Test Mode state until the operator enters the run mode The output will then revert back to the previous On line state NOTE PRESS THE AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE pH Utilities Menu Manual Test Mode 4 4 Page 17 MULTI PARAMETER TRANSMITTER USER S MANUAL ETX RUN MODE 7 15pH_25 0C DOWN CALIBRATION DOWN UTILITIES 4 MANUAL TEST MODE To reset the controller back to all the factory default values reselect the current meter type Then press Gow The controller will initialize itself for a specific meter pH Utilities Menu Meter Selection 4 5 pH Utilities Menu Meter Selection 4 5 The Meter Selection menu is used to select the meter type t
74. tal Rollover 7 13 Page 77 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Flow Output Menu 4 20mA Output 7 14 The Transmitter has a single 4 20mA output electrically isolated from the ground The output can source current into a maximum of 800 ohms See Section 3 9 for wiring diagram The channel has a fully adjustable 4 amp 20 mA output adjustments This will enable the operator to span the output over the desired range The example below shows the 4 20 mA set to 4mA 20 and 20mA 90 The output would then span 4 to 20 mA for a flow swing of 20 to 90 Note that the span can reversed in that 4 mA can be set to a high flow value and 20 mA can be set to a low flow value effectively reversing the control direction ar If you wish to change the setting press the G gt gt key once which will move the cursor to the first character of the value to be changed 4 20mA PROC ay 4 20mA PROC 4mA OUT 000 DOWN 4 20mA PROC NOTE 4mA OUT 20001 s Press the G gt gt key once PRESS THE C AND KEYS which will move the cursor TOGETHER TO GO IMMEDIATELY BACK TO back to the RH side of the RUN MODE 4 20mA PROC display 4mA OUT 20 00 Bown Press the Gow key to accept the setting and move to the next setting Use the Cur and keys to change the setting The TUNE fuction allows the user to precisely adjust the 4 20 mA output to If you wish to change the setting press the G gt gt compensate for any errors in
75. th the known temperature of the probe or process T COMP OVERRIDE Press the Q key once TEMP 35 which will move the cursor back to the RH side of temperature display T COMP OVERRIDE TEMP 35 7 Press the key to accept the reading and move to the store function If you wish to save the setting press the 47 key to highlight the Y character erail ecu pressing ine Cony OVERRIDE r COMP OVERRIDE simply return to the T Comp Override STORE Y N STORE MN Menu This function is useful if you wish DOWN DOWN to view the current selection without making any changes Not stored Then press the key to store the Stored selection and return to the T COMP OVERRIDE Menu Conductivity Setup Menu T Comp Override 6 10 Page 56 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Setup Menu Display Damping 6 11 The Display Damping menu allows the user to adjust COND RANGE the rate at which the display and the output is updated This allows the user to dampen out unstable process readings UNIT The damping can be from 0 seconds to 10 Bown seconds default value is 0 sec TEMP SENSOR DOWN AUTO RETURN DOWN T COMP OVERRIDE Press the Gr key once which will move the cursor over the seconds digit DOWN DOWN DISPLAY DAMPING 3 1 IDISPLAY DAMPING UPDATE 0 SEC DOWN DISPLAY DAMPING Use the CuP gt and Cow to adjust UPDATE gt t
76. the calibration did not appear MANUAL CAL COND MANUAL CAL COND Press to store the to be correct press the calibration data and return key which will return back to the back to the Manual Cal Cond Manual Cal Cond menu menu so the user can select another function NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Calibration Menu Manual Calibrate 6 1 Page 47 K MULTI PARAMETER TRANSMITTER USER S MANUAL TX Conductivity Calibration Menu Dry Cal Cond 6 2 DRY CAL COND NOTE ACCELERATOR KEYS Pressing the or key once will change the valu by the smallest digit Holding the key down will cause the value to change at an increasing rate until the key is released Pressing the key again will cause the value to start changing at it s slowest rate again This allows the user to get to the new multiplier value quickly Dry Calibration eliminates the need for conductivity reference solutions the user inputs the Cell K factor supplied by the factory If the conductivity cell has a tag attached to it specifying the exact cell constant the user is prompted to enter this value DRY CALIBRATION E KFACTOR 1 0000 DRY CALIBRATION KFACTOR 10000 gt Press the Gr key once which will move the cursor over the least sign digit of the display Use and keys to adjust the value to the K factor specified on the p
77. the output key once which will move the cursor to the first circuitry Normally fine tuning the 4 20mA character of the value to be changed output is not necessary 4 20mA PROC 4 4 20mA PROC The make the adjustment place an 20mA OUT 100 00 20mA OUT 100 0101 gt Ge accurate current meter in series with the 4 20 mA output with the appropriate gowy keys to change the setting loads connected When the TUNE menu 4 20mA PROC is selected the controller puts 20 mA out 20mA OUT 90001 gt Press the key once the terminals Use the CUP which will move the cursor keys to adjust the 20mA output to get back to the RH side of the exactly 20 display The TUNE value can be adjusted over the range from 0 to 1000 these are unitless Bown Press the key to accept the numbers used for tuning purposes only setting and move to the next setting If you wish to change the setting press the key will NOT store the selection but key once which will move the cursor to the first character of the value to be changed simply return to the OUTPUT Menu This function is useful if you wish to view the 4 20 PROC 4 20mA PROC TS i i i 20mA TUNE 512 20mA TUNE 512 m m without making any m m D gt Use the CF 2 ges keys to change the setting 4 20mA PROC 45 4 20mA PROC STORE YN 20mA TUNE 540 gt Press the G gt gt key once which will move the cursor fw Or press the back to the RH side
78. the store function to save the selection PROBE SELECT COMBINATION Press the Gr key once which will move the cursor back to the RH side of the display PROBE SELECT COMBINATION DOWN Press the Gow key to accept the setting and move to the store function ap NI Or press the key to highlight With N selected pressing the the Y CH key will NOT store the selection but simply return to the PROBE SELECT PROBE SELECT PROBE SELECT Menu This function is useful if you TORE Y N 1 STORE wish to view the current selection without making any changes Then press the key to store the Not stored Stored selection and return to the PROBE SELECT Menu Note Refer to Appendix A Probe Configuration Table NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE ORP Setup Menu Probe Select 5 5 Page 35 MULTI PARAMETER TRANSMITTER USER S MANUAL TX ORP Setup Menu Temp Unit 5 6 TEMP UNIT allows the user to select either Degrees Centigrade or Fahrenheit units for display Press key once which will move the cursor over the unit type C or F Use the Qu or Gow to select C or F Press the G gt gt key once which will move the cursor back to the RH side of the display TEMP UNIT DEGREE gt Press the key to accept the change and move to the store function Or press the Gr key to highlight the
79. umeric LCD display Power Requirements 4 to 20mA Loop Powered 16 to 32 VDC Measuring Range Temperature Compensation Flow 0 to 9999 with selectable flow rate units Volume 0 999 with Auto Range Flow rate units Gallons GP Cubic Feet CF Liters LP Cubic Meters CM custom by entering factor related to Gallons 701999 0 to 2 000 0 01 pH 0 01 to 14 00 ORP 1999 to 1999mV Dependent on sensor uS cm m TT o 200 Temp 0 to 100 C or 1 32 to 212 F Temp 0 to 100 C or 32 to 212 F 0202000 o EE to 100 C or 32 to 212 F Hours Automatic or Manual Time units Seconds S Minutes M Temp Automatic or Manual 0 100 C 32 to 212 F User selectable temperature compensation slope 0 0 to 10 0 C 0 to 100 C 32 to 212 F Not required Not required Temperature Unit C or F Not required Temperature Sensor User selectable 3000 NTC Thermistor 3000Q NTC Thermistor or Pt 1000 RTD Not required Auto Calibration Dry Calibration Manual Calibration Calibration Modes Manual Calibration cd Sample Calibration K factor Input Temperature Calibration Temperature Calibration Temperature Calibration Ambient Conditions Temperature 20 C to 60 or 4 F to 140 F Humidity 0 to 90 RH non condensing Sensor to Transmitter Differential Sensor 3000 ft 300 ft 2000 ft Distance Combination Sensor 10 ft Analog Output
80. which CALIBRATION DATA Dry Cal does not use a buffer so CAL TEMP 25 2C calibration was performed CAL TEMP Probe Temperature was 25 2 not recorded PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Diagnostics Menu Calibration Data 6 14 Page 60 MULTI PARAMETER TRANSMITTER USER S MANUAL 7 Conductivity Diagnostics Menu Sensor Input 6 15 1000uS 25 0C The Sensor Input Menu allows the user to view real time uncompensated process data from the conductivity cell This is a Read only menu item This Live Data screen is useful for trouble shooting purposes when diagnosing cell or process problems FIRMWARE REV Press to view the Sensor Input data CELL 966 The top line shows the resistance of the cell The bottom line shows the actual value of the TEMP 2953 Q temperature sensor in ohms NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Conductivity Diagnostics Menu Sensor Input 6 15 Page 61 MULTI PARAMETER TRANSMITTER USER S MANUAL ETX 4 20mA PROC AmAQUT 0 lt r DOWN NOTE PRESS THE C AND KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE The TUNE fuction allows the user to precisely adjust the 4 20 mA output to compensate for any errors in the output circuitry Normally fine tuning the 4 20mA output is not necessary The make the adjustment place an accurate current meter
81. which will move the cursor over the least sign digit of the temperature display Use the and to adjust the reading until it agrees with the known temperature of the probe Press the key once which will move the cursor back to the RH side of temperature display Press the key to accept the reading and move to the store function T FACTOR SHIFTED will be displayed for 5 seconds to indicate that the temperature sensor has been calibrated The Shark will then move to the store function 45 TEMP CALIBRATION This will store the calibration data STORE and return back to the Temp Calibration setup so the user DOWN select another function NOTE PRESS THE AND ow KEYS TOGETHER TO GO IMMEDIATELY BACK TO RUN MODE Page 32 MULTI PARAMETER TRANSMITTER USER S MANUAL TX Utilities Menu Manual Test Mode 5 3 Manual Test Mode is used to simulate a process reading in order to verify the correct response of the output When in the Manual Test Mode the outputs is no longer placed on hold as it is when in the rest of the menu The range is 0 to 1000 Press the 07 key once which will move the cursor over the least digit of the simulated process value Use the and keys to change the simulated process value 16 8mA The 4 20 mA output will follow the process value change The 4 20 mA output will track the change in process value Press t

Manual - Process Controls

Contents

Download Pdf Manuals

Related Search

Related Contents