Askari Alarm I/O - ASKARI BEAMS www.askaribeams.co.za
Contents
1. Amna Opt Pulsed Arming Output nacaiver beep twice Latched Arming Latched Arming Output Receiver i a e Monitors up to 8 Askari Scouts signals When the siren is not running pressing the Disarm button 2100 Com fori d d on the Nano will disarm the system and turn off the LED Guard Tamper or Intruder auto test and tamper and the Alarm I O will confirm receipt of the signal the e Receives arm disarm and panic signals from the Nano will beep twice Askari Nano If the system has been triggered the disarm signal Transmitter confirmation will cause the Nano to beep twice with an Eaa additional high tone to alert the owner that the system e Transmits confirmation of receipt of all transmissions has been triggered from the Askari Nano except panic 2 On receipt of the disarm signal from the Nano the Alarm I O will also send the system zone status to the Nano The General _ Nano LED s will now show all the E NOTE Disarm does not reset the zone Can be armed and disarmed via a Pulsed or active and triggered zones on the Alarm I O This will alert Latched input l l ee LED s on the Alarm I O pu the owner of any intrusion and identify where the intru sion took place allowing the owner to make an informed Pulsed from cheap RX and TX set decision about re entering the property after an intrusion has occurred TO ARM DISARM amp PANIC THE ASKARI I O BOARD Latched from GSM modules or Alarm panels Has an Armed Disa2. is connected 1 Press and release the Program switch on the Alarm I O the Programming LED will light up 2 All the programmed zone LED s will light up 3 Wait for the Programming LED to briefly go off and on again all programmed zone LED s will switch off 4 Press and release the zone 1 button U 5 The zone 1 led will light up AS KARI
3. When the Arm and Disarm buttons on the Nano are pressed simultaneously the Alarm I O will trigger the Panic output for 2 seconds and will also drive the Siren Housing Tamper output 2 Housing Tamper NOTE The Nano will remain silent for this function and 12 Volts will not emit a beep Ground Com So 5 Guard 1 An Askari Nano must be programmed into the Alarm I O 6 ifm When the Arm button is pressed on the Nano the siren 8 Gad3 output will be armed for all active zones and the Status ve Led if connected will switch on 9 Com Guard 4 When the Arm signal is received by the Alarm I O d0 Guards it will confirm receipt the Nano will beep once and all the O C Stand Alone Siren and LED Outputs ASKARI ALARM I O active zone LED s will automatically reset to solid lights ie Com those active zones that were flashing due to being trig OPERATORS MANUAL gered will now stop flashing and burn solid a Guard 7 If an intruder signal is received the siren will run for 15 The Askari Alarm I O is a 30 eee teeny status LED wi start j flash 16 multifunctional receiver transmitter While the siren is running pressing the Disarm button Latched Arming Input stand alone alarm system and on the Nano will reset the siren but will not disarm the je puede AG IADUT Al 11 O Interf system but will reset Status LED to Armed on and the dal arm pane nterrace Alarm I O will confirm receipt of the signal the Nano will a pusen
4. isarm output 1 Latched Arm Disarm output A Programming Askari Scout detectors To Operate as a stand alone alarm system or combined with the alarm panel interface the 1 Remove the battery cover from the Askari Scout you wish to program or set the Alarm I O has the following outputs controlled by a Programmed Nano Nano into clone mode 1 Siren output 2 Press and release the Program switch on the Alarm I O the Programming Deleting 1 System status LED output LED will light up 3 All programmed zone LED s will light up none will light up if nothing is programmed in Zones can be turned on and off with the zone switches Active zones will have lit LED s 4 Wait for the Program LED to briefly go off and on again all programmed zone LED s When the zone is active the Led will burn solid when it has been triggered it will flash will switch off you are now in programming mode When an intruder signal triggers the zone it will drive the outputs for 2 seconds if the unit 5 Press and release the required zone button the zone LED will light up 6 Trigger the tamper switch on the Askari Scout or trigger the required zone on the ere Autotest is tne ee a a me Pi orang Tether ce shai a The system conducts auto test every 20 minutes and will trigger after 3 consecutive test programmed zone LEDS will be on failures The auto test clock will reset after every successful intruder signal When auto test 8 Repeat as above for all other zones failu
5. re triggers the zone the Sensor Check LED will switch on To determine which Detector has failed auto test and reset the Sensor Check light turn each zone off and on starting at zone 1 until the failed zone turns the Sensor Check light off A sound will be heard if a speaker is connected is armed B Deleting zones 1 Press and release the Delete switch on the Alarm I O the Programming Deleting LED will light up 2 All the programmed zone LED s will light up i ee ie DREN JOGAN Agal Epro ANENE The Alarm I O has its own tamper switch and output The outputs will latch open when the cover is removed 4 Press and release the required zone button 5 The Alarm 1 O will accept the programming return to standby mode and all Askari Scout Detector Tamper programmed LED s will be on the deleted zone will be off When the battery cover is removed from the Askari Scout Detector it will transmit a Tamper signal to the Alarm I O On Receipt of a Tamper signal the Tamper light will switch on and the Tamper output will trigger for 2 seconds C Programming an Askari Nano A programmed Askari Nano will be able to arm and disarm the siren output and LED output on the Alarm I O and trigger the panic output relay To determine which Detector has triggered the tamper signal and to reset the Tamper light turn each zone off and on starting at zone 1 until the tampered zone turns the Tamper light off a beep will be heard if the speaker
6. rmed O P 1 ARM push right hand side button twice Pulsed 2 DISARM push right hand side button amp the left Latched hand side button 3 PANIC push both side buttons similtamously then release them to send PANIC signal ISO 9000 2000 Approved CE X www askaribeams co za 6 Simultaneously press the Left and the Right side buttons on the Askari Nano PROG RAMM ALC Release the buttons 7 The Alarm I O will accept the programming and return to standby mode The Askari Scout Detector needs to be programmed into both the Askari Alarm I O and the i A 8 The Nano will beep once to confirm programming Askari Nano for systems using both devices These functions need to be performed sepa rately for each device If the Askari Nano has already been programmed with Askari Scout Detectors it can clone the information to the Alarm I O See the Askari Scout user manual for Detector data cloning There are 3 programming functions for the Askari Alarm I O 8 separate zone outputs The Askari Alarm I O is an alarm panel interface with the following N C outputs A Programming Askari Scout Detectors 1 Device tamper outputs B Deleting zones 1 Detector tamper outputs 1 Remote Nano panic outputs C Programming Askari Nano 1 Pulsed Arm Disarm input Before programming remove the cover from the Alarm I O and connect to 12 volts at the 1 Latched Arm Disarm input indicated terminal the power indicator LED will switch on 1 Pulsed Arm D
Download Pdf Manuals
Related Search