Vegetable Preparation Machine VPM Operating Manual
Contents
1. PANTHEON Catering Equipment Vegetable Preparation Machine VPM Operating Manual Introduction Thank you for purchasing a Pantheon Catering Equipment product In this booklet you will find instructions for safe operation so please read carefully and retain for future reference Warnings and Precautions The following warnings and precautions are important and must be observed e Ensure voltage and frequency power requirements for the vegetable preparation machine match that of the supply e The machine must be earthed when used There is a danger of electric shock if it is not earthed e Incase of emergency please turn off the power switch and unplug the machine e f the electric wire becomes damaged a qualified engineer or the manufacturer must replace it Pantheon Catering Equipment is not responsible for any accidents or faults caused by amendments made to the machine or improper use by the user Technical Data Specifications Model N Voltage V 220 240V 50Hz Power W 500 Disc Speed rpm Weight Kg 235w x 490d x 480h Installation Positioning The installation of the unit must be performed by a qualified technician only Place the device on top of a solid even safe and stable surface that tolerates the weight of the unit Ensure no flammable products are placed near the unit as it will get hot Position the device appropriately so that the plug is always accessible Also ensure the2. unit isn t placed close to any water Before attempting to set the unit up ensure it is switched off and unplugged The Cutting Blades and Graters Follow the instructions below and use figures 2 4 to ensure the blades and graters are correctly installed 1 To open the unit rotate the knurled locking handle and swing open the top cover See fig 2 2 Fitthe ejector disc ensuring it engages on the drive shaft via the two pegs 3 Locate the dicing grid if required N B Dicing grids will only fit one way See fig 4 4 Locate the slots on the cutting disc in the pegs on the drive shaft and turn through 90 degrees to secure See fig 3 The cutting disc is correctly fitted when its centre boss is flush with the head of the drive shaft Warning The cutting discs must be located removed by handling the plastic disc and NOT by handling the cutting blade 5 Return the cover to its operating position and relock into position using the knurled locking handle Figure 1 4 Br 4 D Figure 3 Figure 4 Operating Instructions 1 Select the correct feed hopper large half moon or small circular and insert the chosen vegetable 2 Then use the feed arm or feed stick to apply gentle constant pressure on the required food 3 As the VPM works rapidly once a vegetable has been placed in the hopper it is imperative to maintain constant pressure to achieve uniform cuts slices This is particularly importa
3. 3 300 004 300 005 Input body 300 006 300 007 300 008 300 009 300 010 Gasket Anchor spindie Knife disc Anchor board 300 014 Oil envelope Central spindle Isolated sheath 300 016 300 017 300 018 300 019 300 020 Block circle Anchor sheath Belt wheel Seat of bod Electric box Bottom board of electric box Bottom board of boc Magnet steel Umbrella bolt Steel sheath 300 024 300 026 300 027 300 028 300 029 300 030 Adjusting bolt Plastic pressing stick Seat of magnet Magnet steel Knife 300 033 300 034 300 036 300 038 Switch _ _ 30 040 Bet 30 0411 Motor 300 042 Gasket _____ _300 044 Bolt 300 046 Bolt
4. nt when using the chipper 4 With smaller vegetables a more uniform slice is achieved utilizing the smaller hopper Warning Under NO circumstances attempt to push vegetables into the machine by hand Maintenance Cleaning The unit should be cleaned after each use Before cleaning ensure the machine is disconnected from the mains All removable parts Ejector Disc Cutting Blades Dicing Grids and Feed Stick are dishwasher safe or may be washed in warm soapy water Prior to placing them back into the unit ensure they have been rinsed and dried thoroughly The body of the machine including the inside of the top cover should be wiped over with a damp cloth Again before operating the unit again ensure it has been dried thoroughly Do NOT use abrasives or other products which are likely to cause damage to the machine body WARNING Never immerse the body of the machine in water or spray directly with a jet of water Troubleshooting In the event the VPM does not operate check and try the following e Ensure the plug fuse is of the correct rating and type and that it has not blown e Check to make sure that both the top cover and the feed arm are correctly positioned and locked e Reset the machine by quickly switching OFF and then ON again Note If none of the above resolves the issue please contact the manufacturer 17 18 19 20 21 22 23 24 25 Parts Diagram __Pa 300 001 300 002 300 00
Download Pdf Manuals
Related Search