IMD-C Series - Autic system AS
Contents
1. Greenline Greenline Industrial Monitors IMD C Series User Manual INVOLUCRO COM Warning This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference Electric Shock Hazard Do not operate the machine with its back cover removed There are dangerous high voltages inside Disclaimer This information in this document is subject to change without notice In no event shall Indumicro com be liable for damages of any kind whether incidental or consequential arising from either the use or misuse of information in this document or in any related materials Table of contents Chapter 1 System description o A A a eens och A aa a Na a A E ad aaa a aa Ga aa a aa 1 12 Ordering INTO MATION sisa aaa aaa aaa naga wayae ya wa ya ya au ne ya adyan pa udut ya ayan ya nayana a ia aya dg ie aan aaa 1 1 3 Features of the IMD C series Chapter 2 Touch screen configuration 22. alas eMPla Technology Inc Version 9 11 0 9126 We provide full range of controllers for both analog resistive and capacitive touch panels The resistive controller communicates with the PC system directly through AS232 PS or USE port The design ts optimized for an accurate sensitive and quick touch performance as well as an ease of use Interface The diver supports a set of operating systems Le Windowe A 2000 windowes A MP Windows Mesta A wind ss I Le Cancel 23 IMD C Series User Manual This page intentionally left blank 24 Chapter 3 Dimensions drawings 3 1 Dimension drawing IMD CO70 P IT D 5 LA O r O r IMD C Series User Manual 0061 25 3 2 Dimension drawing IMD CO80 P T CCC NO NS Joued IMD C Series User Manual 26 3 3 Dimension drawing IMD C120 P T 227 0 A MB LUI NO 0 NO NS SUB Ho IMD C Series User Manual 3 4 Dimension drawing IMD C150 P T gt 310 0 OOP DD Y 290 0 o o Oo o AS a NO NS jsued lth IMD C Series User Manual 0 06 This page intentionally left blank This page intentionally left blank This page intentionally left blank SF Edition 1 0 gt Olndumicro com INVOLUCRO com Tel 31 0 318 668912 sales indumicro com www indumicro com
3. monitor automatically Check this box to enable the driver to generate the mouse event for the primary monitor even though the touchscreen is configured as other monitor mapping and multiple monitor function is enabled The eGalaxTouch driver supports split display mode for those applications which do not map the touchscreen to the full screen of the monitor The options are e Full Screen e Lower Screen e Left Screen e Upper Screen e Right Screen e Other 21 Other Operation Mode When Other is selected in the Operation Mode the user is presented with the following options Other Quarter 3 f Customized Quarter 2 C Quarter 4 Customized dead e 480 let TS tT Fight Bottom Beating ites O Top Cancel The user can opt for the top right quarter of the monitor the top left quarter the bottom left quarter the bottom right quarter or customized When Customized is selected the user can enter a customized area or draw a working area by pressing the Draw Working Area button Hardware eGalaxTouch USB Controller General Setting Tools Display Hardware About Controller Model PCAP7200 Series Firmware Version 1 000 T est OF Cancel IMD C Series User Manual 22 About Displays information about eGalaxTouch and its version IMD C Series User Manual eGalax Touch USB Controller Touch Screen Utility gt Copyright E 2000 2011 eGalax Tauch eh
4. to generate the mouse event A software filter is implemented inside the driver to filter some noise to stabilize and smooth the touch points Enabling this function results a more stable cursor Adjust this parameter for Constant Touch Hold function This criterion is used to judge if the most recent touched point is same as the previous touched point lf the difference in points is within this area it will be recognized as the same touch point and the driver does not generate new mouse event for this new touch point Adjust the Right click time for the Auto Right Click function If the touchscreen is touched and hold for this period of time the driver generates a mouse right click event Tools Calibration draw test tools and the linearity curve of the touchscreen are listed on this page eGalax Touch USB Controller General Setting Tools Display Hardware About Linearization Curve Do 4 points alignment to match display Clear linearization parameter and do 4 points Clear and Calibrate alignment Do 9 points linearization for better touchscreen linearity Do draw test to verify the touch accuracy Draw Test OF Cancel 4 Points Calibration A touchscreen needs calibration before it can work accurately The touchscreen can be re calibrated whenever the user feels the accuracy is lost When the 4 Points Calibration button is pressed a new window will pop up to guide the user through the 4 points ca
5. 1 Configuring a resistive touch screen IMD CxxxT LR 3 2 2 Configuring a projected capacitive touch screen IMD CxxxPT aaa aaa aa aaa anane eaaa aana eaaa 15 Chapter 3 Dimension drawings 3 1 Dimension drawing IMD GOZO T aaa aaa aa a Nana de ga a aga a aka 25 3 2 DIMENSION drawWingIMD GOS80IP TT ges ese eue a dead 26 23 DIMENSION AFAWINO IMC I ZOU PY lues nn Aa 27 3 4 Dimension drawing IMDEC TS0IP Ness sn de ss sh sn ns ns ns uen ce ma Be 28 Chapter 1 System description 1 1 Specifications moa or mo cosopr mocz mocion Display Display type 7 TFT LCD 8 TFT LCD 15 TFT LCD Luminance cd m 350 350 330 Touch Screen Type Resistive touch IMD CxxxT Anti scratch projected capacitive touch IMD CxxxPT Light transmission 80 IMD CxxxT 90 IMD CxxxPT Connectivity Connectors 1 x USB for touch 1x VGA 1 x DVI 1 x 3 pin terminal block for power Input voltage 9 36V DC Power consumption Max 2 4W Max 4 6W Max 11W OSD keypad 5 key keypad located on the backside Construction Aluminum front and chassis IP Rating IP65 front panel Mounting Panel mount VESA 75 Panel mount VESA 100 Dimensions mm 202 x 149 x 39 231 x 176 x 51 319 x 245 x 52 410 x 310 x 55 Environmental 0 50 C 20 60 C Storage humidity 10 to 90 40 C non condensing CE FCC Class A Operating temperature Storage temperature Certification 1 2 Ordering information IMD CO70T 7 Industrial display
6. are PenMount Monitor Menu Icon The PenMount monitor icon PM appears in the menu bar of Windows 2000 XP 7 system when you turn on PenMount Monitor in PenMount Utilities 10 54 PM 0 13 4015 The PenMount Monitor has the following functions Control Panel Beep Right Button Exit IMD C Series User Manual Control Panel Y Device Beep Right Button Exit Opens the Control Panel window Set Beep function for each device When you select this function a mouse icon appears on the desktop Click this icon to switch between right and left button functions Exits the PenMount Monitor function You can opt to display the Mouse Icon in the System Tray instead of on the desktop To do so follow these steps 1 Open the PenMount Control Panel 2 Select the Tools tab 3 Select the System Tray option Device Multiple Monitors Tools About Test by drarwing on the touch screen Bra cq Show Hide the icon for switchine Right Button Icon gt De The Mouse Icon will then appear in the System Tray 2 02 PM 0 14 4015 PenMount Rotating Functions The PenMount driver for Windows 2000 XP supports several display rotating software packages Windows Me 2000 XP support display rotating software packages such as e Portrait s Pivot Screen Rotation Software e ATI Display Driver Rotate Function e nVidia Display Driver Rotate Function e SMI Display Driver Rotate Function e Intel 845G GE Display Dri
7. eater accuracy Please follow the step as below 3 Come back to PenMount Control Panel select Device to calibrate then click Advanced Calibration Calibrate Setting Edge Compensation About Advanced Mode E Plot calibration data Standard Calibration Advanced Calibration Turn off EEPROM storage NOTE It is recommended to use a stylus during Advanced Calibration for greater accuracy IMD C Series User Manual Touch the red square Plot Calibration Data Check this function to have touch panel linearity comparison graph appear when you finish Advanced Calibration The black lines reflect the ideal linearity assumed by Penmount s application program while the blue lines show the approximate linearity calculated by Penmounts application program as the result of users execution of Advanced Calibration Turn off EEPROM storage This function disables the write in of calibration data in the controller This function is enabled by default IMD C Series User Manual Setting Calibrate Setting Edge Compensation About Operation Mode Beep Sound Buzzer Beep Beep Mode W Cursor Stabilizer UN en W Use press and hold as right click Stabilizer to remove 2 Delay jitter of cursor Operation Mode Mouse Emulation This operating mode will send left button down function when user presses and left button up function when user release its touch Click On Touch This operating
8. ined in the following sections Device In this window you can find out that how many devices are detected on your system Device Multiple Monitors Tools About Select a device to configure A PenMount 6000 R Calibrate This function offers two ways to calibrate your touch screen Standard Calibration adjusts most touch screens Advanced Calibration adjusts aging touch screens Standard Calibration Click this button and arrows appear pointing to red squares Use your finger or stylus to touch the red squares in sequence After the fifth red point calibration is complete To skip press ESC Advanced Calibration Advanced Calibration uses 4 9 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens Click this button and touch the red squares in sequence with a stylus To skip press ESC IMD C Series User Manual 3 To calibrate your touch screen 1 Please select a device then click Configure You can also double click the device too Device Multiple Monitors Tools About Select a device to configure Calibrate setting Edge Compensation About Advanced Mode E Plot calibration data Turn off EEPROM storage IMD C Series User Manual Touch the red square NOTE The older the touch screen the more Advanced Mode calibration points you need for an accurate calibration Use a stylus during Advanced Calibration for gr
9. is value will affect the double click behavior for all of the mice devices in the system Two continuous clicks in the same area within this specified time period will be recognized as a double click event The Double Click Area group is used to set the system double click area Changing this value will affect the double click behavior for all of the mice devices in the system Two continuous click in the specified area within the specified double click time will be recognized as a double click event There are 5 mouse emulation modes for eGalaxTouch touchscreen controllers Press the button to change the emulation mode Normal mode Normal mode behaves like mouse button down and mouse move User can select this mode to select and drag an object Click On Touch With this Click On Touch mode the driver emulates a mouse click event when the touchscreen state was switched from untouched state to touched state The driver will generate a mouse move event and tracks the touch position until the touchscreen state is switched to untouched state Click On Release When the Click On Release mode is selected the driver will emulate a mouse click event when the touchscreen state was switched from touched state to untouched state Click On Touch without moving cursor When this mode is selected the driver will behave similar as Click On Touch mode The cursor does not move to the touch position except the first touch point Click On Release witho
10. isplays Device Multiple Monitors Tools About i Multiple Monitor Support Map Touch Screens IMD C Series User Manual 10 2 When the mapping screen message appears click OK Device Multiple Monitors Tools About e Multiple Monitor Support 3 Touch each screen as it displays Please touch this monitor Following this sequence and touching each screen is called mapping the touch screens 4 Touching all screens completes the mapping and the desktop reappears on the monitors 5 Select a display and execute the Calibration function A message to start calibration appears Click OK To start calibration please touch the panel to calibrate in the following screen IMD C Series User Manual 11 6 Touch this screen to start its calibration appears on one of the screens Touch the screen 7 Touch the red square messages appear Touch the red squares in sequence 8 Continue calibration for each monitor by clicking Standard Calibration and touching the red squares NOTES 1 If you use a single VGA output for multiple monitors please do not use the Multiple Monitor function Just follow the regular procedure for calibration on each of your desktop monitors 2 The Rotating function is disabled if you use the Multiple Monitor function 3 If you change the resolution of display or screen address you have to redo Map Touch Screens so the system understands where the displays
11. libration User should follows the guide to touch and hold the blinking symbol in the calibration window until it shows OK to make sure that the utility can gather enough data for computation IMD C Series User Manual 19 Clear and Calibrate Press this button to erase the calibration linearization parameters and Linearization Draw Test re calibrate using the 4 points calibration The driver reads the data input from the controller to generate a mouse event However it can be enabled or disabled to generate the mouse event This function is used for accuracy and performance check User can press the Clear button to clear the window Press Quit button to terminate this draw test IMD C Series User Manual 20 Display In this window it shows the mode of display eGalaxTouch USB Controller General Setting Tools Display Hardware About Enable Multiple Monitors Map to main monitor when the system has only one monitor Operation Mode IMD C Series User Manual Display Double click on the monitor area to map the touchscreen to the display monitor iw Enable Multiple Monitor Map to main display if system has only one display monitor Operation Mode a v f Full Screen f Lower Screen f Lett Screen f Upper Screen f Right Screen Other coed Check this check box to enable multiple monitor support When this function is disabled the touchscreen will be mapped to the primary
12. mode will send a mouse click only on user s touch Dragging is disabled in this mode Pen Input Emulation When using Pen Input Emulation the PenMount device driver will not send left mouse button right away therefore it is recommended to use this mode with the press and hold right mouse button emulation it will be able to activate right mouse function on Start Menu and other utility Click On Release This operation mode will send a mouse click when user release its touch operation This feature works well when browsing certain web pages NOTE The actual mouse functions generated by the above operating modes can be viewed from the PenMount DRAW utility IMD C Series User Manual 7 Beep Sound Enable Beep Sound Turns beep function on or off Beep on pen down Beep occurs when pen comes down Beep on pen up Beep occurs when pen is lifted Beep on both Beep occurs when pen comes down and when it s lifted Beep Frequency Modifies sound frequency Beep Duration Modifies sound duration Cursor Stabilizer Enable this function to prevent cursor shake Use press and hold as right click Set the time and area as needed Edge Compensation The Edge Compensation function is used to optimize the cursor accuracy on the edges lt is only supported by Advanced Calibration not for Standard Calibration Calibrate Setting Edge Compensation About Small Large Left 3 Back
13. rollers eGalax Touch supports plug and play for USB devices The icon object for an additional USB controller will be shown automatically in the controller list window when the USB controller is connected with the system USB port Remove This function is used for serial controllers only Setting eGalax louch USB Controller Frequency HE jan Beep On Release er i Beep From System Beep LINE Beep From Sound Card J ES Double Click Time Shorter a Longer Double Click Area Smaller lt lt a Y gt gt Bigger Normal Mode Option caca to Beep On Touch Check this check box to enable driver to generate a beep sound when touch touchscreen state is switched from untouched to touched state Beep On Release Check this check box to enable driver to generate a beep sound when touchscreen state is switched from touched state to untouched state Beep From System Beep Check this check box to make the beep from system speaker Beep From Sound Card Check this check box to make the beep from sound card Frequency Adjust this frequency to control the beep sound frequency generated by the driver Duration Adjust this duration to control the beep sound duration IMD C Series User Manual 16 Linearization Style Double Click Time Double Click Area Mouse Emulation Mode IMD C Series User Manual Select 9 points or 25 points The Double Click Time group is used to set system double click time Changing th
14. to Default IMD C Series User Manual About This panel displays information about the PenMount controller and driver version Device Multiple Monitors Tools About P Penmount Control Panel Version 1 0 0 63 Installed Device s Device 0 PenMount 6000 R5232 Support E mail penmountiseed ret tw Support Website tbo fun pre rro con kyu IMD C Series User Manual Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system The PenMount drivers for Windows 2000 XP support Multiple Monitors This function supports from two to six touch screen displays for one system Each monitor requires its own PenMount touch screen control board either installed inside the display or in a central unit The PenMount control boards must be connected to the computer COM ports via the RS 232 interface Driver installation procedures are the same as for a single monitor Multiple Monitors support the following modes e Windows Extends Monitor Function e Matrox DualHead Multi Screen Function e nVidia nView Function NOTE The Multiple Monitor function is for use with multiple displays only Do not use this function if you have only one touch screen display Please note once you turn on this function the rotating function is disabled Enable the multiple display function as follows 1 Check the Enable Multiple Monitor Support box then click Map Touch Screens to assign touch controllers to d
15. ut moving cursor When this mode is selected the driver will behave similar as Click On Release mode The cursor does not move to the touch position except the lift off point Desktop Mode When Desktop Mode is selected the driver will behave similar as Normal Mode But the driver will not report mouse button down immediately after user touches down User needs to touch and stay at one point for a few milli second then the driver will report mouse touch down Option The advanced functions are Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Hold Area Auto Right Click Time IMD C Series User Manual Option Function iW Enable Auto Right Click iW Enable Touch if Enable Cursor Stabilization Constant Touch 4rea E Smaller lt lt gt Bigger Auto Right Click Time 1000 ras Shorter lt lt gt Longer Cancel Constant Touch is the function to check if the most recent touched position is same as the previous touched point If the difference in points is smaller than the defined area the driver does not generate any mouse event to reduce system loading If the touchscreen was kept touched for a specified time the driver will generate a mouse right button click event if this function was enabled The driver reads the data input from the controller to generate a mouse event However it can be enabled or disabled
16. ver Rotate Function IMD C Series User Manual 13 Configuring the Rotate Function 1 Install the rotation software package 2 Choose the rotate function 0 90 180 270 in the 3rd party software The calibration screen appears automatically Touch this point and rotation is mapped Touch the red square NOTE The Rotate function is disabled if you use Monitor Mapping IMD C Series User Manual 2 2 Configuring a projected capacitive touch screen IMD CxxxPT eGalaxTouch Control Panel The functions of the PenMount Control Panel are General Setting Tools Display Hardware and About which are explained in the following sections General This window will show the installed USB Controller eGalaxTouch USB Controller General Setting Tools Display Hardware About Installed Touchscreen Controllers gt USB USB Controller Monitor ddd Remove Mapping Cancel Apply 3 Option buttons are shown Monitor Mapping The eGalax Touch driver utility supports multiple monitors This function allows the user to map the monitors When this option is selected a pop up window will pop up Please touch the touchscreen panel to map the monitors Press ESC to quit naass SPACE bar to skip to Next Screen Auto skip to next screen After the mapping has finished the monitors should be calibrated IMD C Series User Manual 15 Add This function button is only used to add serial RS232 cont
17. with resistive touch screen IMD CO70PT 7 Industrial display with projected capacitive touch screen IMD CO80T 8 Industrial display with resistive touch screen IMD CO80PT 8 Industrial display with projected capacitive touch screen IMD C120T 12 Industrial display with resistive touch screen IMD C120PT 12 Industrial display with projected capacitive touch screen IMD C150T 15 Industrial display with resistive touch screen IMD C150PT 15 Industrial display with projected capacitive touch screen IMD C Series User Manual 1 3 Features of the IMD C series The IMD C series feature an excellent viewing ability for monitoring and control applications The front panel of the display monitor is sealed with a gasket for NEMA 4 IP 65 rating when it is panel mounted in a NEMA rated cabinet or enclosure The T models are equipped with an analog resistive touch screen while the PT models come with a projected Capacitive touch screen Projected capacitive touch screens are not only resistant to scratch and abrasion but also to most chemicals Apart from that glass is transparent and does not impair the brilliance of the picture at all IMD CO70 P T IMD C150 P T IMD C Series User Manual 2 Chapter 2 Touch screen configuration 2 1 Configuring a resistive touch screen IMD CxxxT PenMount Control Panel The functions of the PenMount Control Panel are Device Multiple Monitors Tools and About which are expla
Download Pdf Manuals
Related Search