ECO Spot™ LED40DE User Manual
Contents
1. ECO Spot LED40DE User Manual ECO Spot LED40DE User Manual The ECO Spot LED40DE is intended for exterior applications but a is also suitable for interior use Thank you for choosing an ECO gi Spot Gobo projector This unit is equipped with a fan cooled heat 9 pipe to keep the 40W High Power LED running cool It is also available as interior version ES LED40D ee Please read this manual before installing or operating this fixture La follow the safety precautions listed below and observe all warnings WARNING To prevent damage to the LED always connect the driver cable to the projector FIRST before plugging it into the power outlet Package Contents v Projector External LED Driver Test Gobo Spare gobo retaining ring and spare drive belt Gobo adapter ring for E Size Gobos Safety Information Place your fixture at a suitable place with good air flow Keep flammable materials away from the fixture Minimum distance to flammable material 1 ft 0 3m Minimum distance to illuminated surface 3 3 ft 1 0m Provide a minimum clearance of 4 in 10cm around air vents Use only genuine spare parts for part replacement Do not look directly into the lamp it can cause eye damage Always unplug the unit from the power mains before any service is done Light fixtures should be installed and maintained only by qualified personnel with experience in lighting equipment and general electrical experience Disconne2. ct the fixture from AC power before handling the fixture Always ground earth the fixture electrically Use only a power source that complies with local building and electrical codes and has both overload and ground fault protection Do not use the fixture if the power cable or power plug is in any way damaged defective or wet or if they show signs of overheating Copyright 2014 Globus New Media LLC Page 1 ECO Spot LED40DE User Manual Handling Instructions There is a weatherproof connector between the driver power supply and projector which can be opened for easier handling Always make this connection first before powering up the driver otherwise the LED can be damaged by the power surge Before the initial start up please unpack and carefully check for damage caused during transportation Place your fixture at a suitable place with good air flow Make sure there are no flammable materials close to the lamp When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices e Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Warranty One Year from Date of Purchase Keep your receipt for reference and contact your dealer in case of warranty issues Projection Lenses The projector accommodates interchangeable projection lenses to allo
3. ifications for exact dimensions For max image size and brightness use D Size gobos The recommended gobo image diameter is 35mm An Image Diameter of up to 40mm is possible with some loss in focusing quality for optimal focus stay within 32mm image size Unscrew the thumbscrews to remove the front cover with the projection lens Push the two pins of the gobo retaining ring together and pull out the retaining ring Carefully remove the old gobo and replace it with the new gobo Tip Tilt the projector forward while placing the palm of your hand inside the old gobo will fall into your hand If you have a glass gobo place the more reflective side towards the light bulb Replace the retaining ring and make sure it evenly pushes the gobo all the way back Replace the front cover and adjust the focus by threading the projection lens in or out Copyright 2014 Globus New Media LLC Page 3 ECO Spot LED40DE User Manual Line Voltage 100 240V 50 60Hz 0 6A 48W Ambient Operating Temperature 13 to 104 F 25 to 40 C Dimensions Weight Body without yoke 10 5 x 6 x 3 75in Lx W x H 267 x 153 x 95mm The projection lens adds 0 5 to 2in 12 to 50mm to the length Height with yoke 7 75in 197mm Weight 7lbs 3kg Gobo Dimensions D Size Metal or Glass Gobos and Dichroic filters The projector takes D Size gobos Outer Diameter OD 53mm Image Diameter ID 35mm max 40mm Max Thickness 4m
4. m Larger ID up to 40mm is possible with some loss in focusing quality for optimal focus stay within 32mm image size An adapter for the smaller E Size gobos is included Page 4 Extremely high light density for ultra efficient projection Power 40W 6 Bulb life 50 000h Color Temperature 5 500k 500k Rated Luminous flux 2 000Im Effective luminous flux 1 500Ilm The projector can be equipped with standard projection lenses of the ECO Spot line These lenses are marked based on a gobo image size of 25mm With the larger gobo image size a given lens produces a larger image than the lens specification see the effective lens angles in below The more narrow the lens the smaller and brighter the image will be at a given distance Currently these lenses are available Wide 25 effective 35 Medium 20 eff 28 Medium Narrow 15 eff 21 Narrow 10 eff 14 IP Ratings LED Driver IP65 e Fixture equivalent to IP62 Copyright 2014 Globus New Media LLC
5. w optimizing the projection size and resulting brightness at varying distances The more narrow the lens the smaller and brighter the image will be at a given distance For example cutting the projection size in half will quadruple its brightness Gobo Rotator If the fixture is equipped with a gobo rotator it can be turned on off with the silver push button on the front plate underneath the lens There are no controls for rotating speed or direction Power up the projector If the fixture is equipped with a gobo rotator turn it on once the gobo projects in the desired position turn it off Loosen the outer ring around the lens that acts as a water seal Focus the projection by twisting the lens in and out until the image is well focused When used for the first time the lens will often need to be twisted outwards many rotations to reach the focusing point When in doubt keep going Re tighten the outer ring to ensure a tight seal of the lens Page 2 Copyright 2014 Globus New Media LLC ECO Spot LED40DE User Manual Multi functional Yoke The yoke can slide over the whole length of the fixture body to accommodate a wide range of pointing directions The yoke can also serve as stand The yoke can be screwed to a wall or ceiling or fastened with a C clamp Gobo Placement see Specifications for Gobo Dimensions The ES LED40DE uses D Size gobos or E Size gobos with an adapter ring See the Spec
Download Pdf Manuals
Related Search