Installation and - PDi Communication Systems
Contents
1. The SETUP menu is the first menu that appears All the other menus and all the settings can be accessed through it This manual explains and shows how to setup the different features of the PDI P23LCDD TV PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide P2ge 16 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Service Levels The P23 contains four separate Service Levels allowing the hospital to offer either basic or enhanced viewing The current Service Level can quickly be determined by accessing the SETUP menu using the remote control The Service Level can be changed to any of the 4 levels at any time Service Level Picture Sound Channels Features OSD Language Sources FM Radio Position A V Exit SETUP Next lt gt DISABLED This is like a mechanical key lock when in Disabled Service Level the TV can be turned off and on but it cannot be used for viewing A standard message appears on a black screen FREE This lets patients watch hospital education and information channels without renting the TV The channels containing programming for no charge are typically programmed into this level of service This is the factory default setting for Service Level BASIC This service level typically allows add2. bracket Position the Wall Bracket sos og and locate two mounting holes URI x36 Secure the bracket to the wall mounting hardware is not included 8 Ls i5 A C Wall Across Room Bracket Wiring amp CATV Signal mcm mcm mm m 2 Refer to Figure 2 Position the Back Mount on the LCD TV cabinet Attach with the four Figure 1 M4 screws that are provided 3 Mate the Back Mount to the Wall Bracket making sure the pivot pins are retained in the U shaped slot Using the pilfer security driver packed with the hardware secure with two 10x32 pilfer screws 4 Connect the AC power cord Pillow Speaker Jumper Cable and CATV Coax Cable See Pillow Speaker section on page 11 before connecting Jumper Cable 5 The TV s tilt can be adjusted by loosening both Pilfer Screws adjusting tilt and then tightening the screws Figure 2 Back Mount Screws 4 Pilfer Screws 2 f CATV Coax Connector H Coax Not Shown PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC FOLO Losses PDI P23LCDD TV Installation Guide o6 Systems Inc Better Solutions Are Within Reach M INSTALLATION and OPERATING INSTRUCTIONS Across Room Wiring A stereo style pillow speaker pendant control jack is located on the TV s connector panel on the backside This TV i
3. Component Input Picture When the TV s source is set to Component 1 or 2 additional picture adjustments are available Component 1 2 Input Picture Temperature Temperature is a measure of the warmth of m Temperature an image Two temperatures available are 6500K and 9300K ARC ARC Aspect Ratio Control Select the ratio of the screen m H Position size Horizontal Vertical 4 3 14 9 or 16 9 m V Position H Position Horizontal Position The H Position moves the picture left or right across the screen V Position Vertical Position The V Position moves the picture up or down on the screen Position A V Exit SETUP Next lt gt 1 Enter the Picture menu 2 Press A or V to highlight Component Input Picture 3 Access the menu by pressing P 4 Press A or V to highlight and select one ofthe settings 5 Press 4 and gt to adjust the setting See description of settings above 6 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Limited Warranty PDI Communication Systems Inc PDT warrants to the original purchaser only that the PDI P23 LCDD will be free from defects in materials and workmanship under normal use for 2 years from the date of original purchase This warranty does not cover any other equipment that may have been included with PDI s shipment of this product After receipt of written notice of a defect or malfunction occurring during the warr
4. Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Diagnostics This menu provides readouts of the TV s internal operation The Diagnostics menu items are read only and can not be changed Diagnostics Field ON Hours 000002 Field Power Hours 000098 Firmware VSN 1 06 Micom VSN 6 6 Exit SETUP Field ON Hours Cumulative time TV is actually on Field Powered Hours Cumulative time TV is powered Firmware VSN Main firmware version Micom VSN Micom firmware version Enter the Features menu Press A or V to highlight Diagnostics Press to select it Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear Soc Channel Up Power Off This feature causes the TV to turn off once it reaches the highest numbered last channel and is usually used with single button style pillow speakers When the feature is disabled the TV will continue on to the lowest channel and not turn off 1 Enter the Features menu 2 Press A or V to highlight Channel Up Power Off 3 Press 4 or gt to select Enabled or Disabled 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Channel to Other Source External signal sources connected to the TV such as DVD players or video game systems are shown in the current channel lineup after the highest channel and then shown on the TV Set this feature to
5. 32 Digital Mode Time Setup s099 Diagnostics 1 84 Channel Up Power Off 1 84 Channel to Other Source 134 Power On ARGC MOJE ooien aeae aaa a ad ureipe vate D IM IM Pts IDIOMS D MS MEE 35 Standby POW eR C P E aaa 35 On Screen Menu Language Selection ES Ec s 95 Power On Source 1 36 FM Radio 96 PAULO rere Ir RETRO iaa AE Eana SeA a eSATA KUNVE AO Dea ada Daai E DA aaa aaa i i aea DEA EANA AEE REE aa EENAA 36 PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 x Document Number PD196 158 DOC r LJ Communication PDI P23LCDD TV Installation Guide Pase 6 0f 42 Systems Inc Better Solutions Are Within Reach M INSTALLATION and OPERATING INSTRUCTIONS Add Delete Stations RRRRRRRRRMEMEMEMMMEEMMMEIMMMM 36 PHIL 37 Save Settings to USB drive ssssssssssssssssssssseseneeeennnen nennt ste tnns ihn rnts inns sintesi titres sh nnnt ssa nsn t Entenana tinta 37 Restore Setting to TV 98 Information 99 Firmware Appendix ARC adjustments A PC Analg ADMI Picture e SM 41 Component Aput PICIU ETT teda aa daa eaaa anwa a ra iaaa aa adap peda kaiaa doe 42 Limited Warranty coccciscice ccecciegese
6. A Adiust To V Exit SETUP Next lt gt Position A V Exit SETUP Next lt gt Enter the Channels menu Press A or V to highlight Copy Service Level Press to select it Press A to set the From Service Level Press V to set the To Service Level Press to copy the Service Level A confirmation page will appear Press A to proceed Press V or SETUP to return to the previous menu NOTE After a Service Level is copied the TV returns to the Copy Service Level menu If the To Service Level has been set to active in the Service Level setting see Service Levels on page 16 TV programming will appear 7 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Qui Pope pass Parental Control Parental Control allows you to block channels TV shows movies and devices that are connected to the P23 Parental Control TV Rating MPAA Rating Change Password Block Aux Source Unblocked Parental Lock Duration Always Parental Lock Enabled Position A V Exit SETUP Next lt gt Enter the Channels menu 2 Press A or V to highlight Parental Control 3 Press to select it PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 26 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATIN
7. AV Switches TV set on or off Selects the mode to watch TV or use a connected 3CC component Sets the closed caption function 7 Remote Control Sensor Accepts the IR signal from the remote control PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rr L i Communication PDI P23LCDD TV Installation Guide P 2e 13 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Remote Control PD108 420 A programming remote control is required to perform all TV setup adjustments including programming channels The remote is NOT included with the TV and must be ordered separately one remote is capable of programming an entire hospital of TVs Please order programming remote control part number PD108 420 1 POWER button 12 ARC button Turns the TV on or off Changes the aspect ratio 2 MUTE button Repeatedly press the ARC button Q Turns the sound on or off to select your desired picture 3 SETUP button format See page 41 for 5 Access programming instructions on adjusting picture menus up or down 4 TV AV button 13 CC button 8 Selects enabled external Cycles through Closed caption A inputs or TV choices 5 CHLIST button 14 PSMbutton B Display list of channels Adjust sound setting for content programmed into TV type User Standard Dynamic a5 6 TV FM button Mild or Game Switc
8. B Y R Y Connections are color coded 6 ANT Connection to Cable TV Coax NOTE See page 11 7 SVC Service port 8 PC ANALOG IN D SUB Connection to the video output jack on your PC See resolutions in Appendix on page 42 9 SPDIF Provides a digital audio output signal for connecting to an external digital audio device 10 AUDIO OUT Connection for external audio amplifier or speakers 11 HDMI1 IN and 12 HDMI2 IN Connection for HDMI devices 13 USB PORT Firmware upgrading and cloning purposes NOTE See firmware updating and cloning instructions starting on page 37 14 MTI Used to connect to LodgeNet 15 CCI 16 PILLOW Pillow speaker port NOTE See page 11 before connecting PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC FOLO comiso PDI P23LCDD TV Installation Guide Pee 1 of Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Antenna ANT Connection Hospital Coax Cable CAUTION Some hospital cable systems provide power voltage on the coaxial cable This TV is NOT designed to be powered via a coaxial cable DO NOT connect to a powered coaxial cable Damage will result to the TV Pillow Speakers The pillow speaker pendant control jack is located on the TV s connector panel Control of the TV using an externally wired pillo
9. PDI P23LCDD TV Installation Guide Pese 8 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Color Temperature Color Temperature adjusts the color balance of the picture Standard Reddish Greenish and Bluish are preset adjustments You can customize the color temperature with the User setting Color Temperature Brightness Standard Contrast Reddish Color Greenish Tint Bluish Color Temperature User Sharpness PC Analog HDMI Picture Component Input Picture Position A V Position A V Exit SETUP Next lt gt Exit SETUP Next lt gt 1 2 3 4 5 6 Enter the Picture menu Press A or V to highlight Color Temperature Access the menu by pressing gt Press A or V to highlight and select one of the five settings For User press lt and gt to select R G or B or to get out of the customized adjustments Press A or V to adjust R G or B NOTE When you select one of the three colors to adjust the other two turn gray 7 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear PC Analog HDMI Picture and Component Input Picture See page 41 for instructions on how to adjust the settings for these two menu items PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm Li Communication PDI P23LCDD TV Installation Guide
10. Page 19 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Sound The sound menu allows precise adjustment of several sound parameters Balance Minimum Volume Maximum Volume Power on Volume Internal Speaker Enable HDMI 1 Audio Port HDMI 2 Audio Port Composite S Video Sound Mode Service Level Picture Sound Channels Features OSD Language English Sources FM RADIO Position A V Position A V Exit SETUP Next 4 Exit SETUP Next lt gt Press the SETUP button on the remote control 2 Press A or V on to highlight Sound 3 Press to enter the Sound sub menu Balance This controls how the sound is distributed between the left and right speakers 1 Enter the Sound menu 2 If Balance is not highlighted press A or V to highlight it 3 Press lt or P to select the desired number 0 100 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Minimum Volume Sets the minimum volume level the TV can reach Setting this to any value other than 0 guarantees that some level of sound will always be heard when the TV is operating Enter the Sound menu 2 Press A or V to highlight Minimum Volume 3 Press 4 or gt to select the desired number 0 100 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Maximum Volume Sets the maximum volume level
11. Press A or V to highlight Composite S Video Sound Mode 3 Press 4 or gt to select L R L L or R R 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide P2ge2 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Channels The Channels menu allows you to program different signal sources into three Service Levels Free Basic and Premium and to add or delete individual channels It also allows you to block channels TV programs movies and auxiliary sources that can be input to the TV Each Service Level contains a different channel map Signal Cable STD Auto Program Add Delete Channels Clear Service Level Copy Service Level Parental Control Power on Channel Channel Lock Disabled Channel Memory Override Enabled Service Level Picture Sound Channels Features OSD Language Sources FM RADIO Position A V Position A A Exit SETUP Next lt gt Exit SETUP Next lt gt 1 Press the SETUP button on the remote control 2 Press A or V to highlight Channels 3 Press to enter the Channels sub menu Signal Four different tuning types are available depending upon the healthcare facility s signal type Sele
12. TV Basic Service Level Enabled TV Premium Service Level Enabled Composite Video Enabled NA 10 10 Enabled Component 1 Enabled Component 2 Enabled HDMI 1 Enabled Balance Minimum Volume Maximum Volume Power on Volume Internal Speaker Enable HDMI 1 Audio Port HDMI 2 Audio Port Composite S Video Sound ode L E L E m E Ei Ei M HDMI 2 Enabled PC ANALOG Enabled FM RADIO Enabled Position A V Position A V Exit SETUP Next lt P gt Exit SETUP Next lt gt Enter the Sound menu Press A or V to highlight the component you want to change Press lt or gt to select Enabled or Disabled Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear hat ae E HDMI 1 and 2 Audio Port Sound can be routed to several other sources when the TV is set to HDMI video The HDMI Audio Port has three settings HDMI 1 or 2 PC and Component 1 or 2 NOTE HDMI 1 Audio Port has the settings HDMI I and Component 1 HDMI 2 Audio Port has the settings HDMI 2 and Component 2 1 Enter the Sound menu 2 Press A or V to highlight HDMI 1 or 2 Audio Port 3 Press 4 or gt to select HDMI lor 2 PC or Component 1 or 2 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Composite S Video Sound Mode Sound can be completely transferred to the left or right speakers It can also be balanced with the L R setting Enter the Sound menu 2
13. brackets support arms and appropriate hardware to assure TV will not fall from the mounted position Failure to do so may cause injury or death RAIN AND MOISTURE WARNING To avoid the hazards of fire or electrical shock DO NOT expose this television to rain or moisture OXYGEN ENVIRONMENT WARNING Do not use in any oxygen tent or oxygen chamber Such use may cause a fire hazard WET LOCATION Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Peepe NOTE TO CABLE TV INSTALLER This reminder is provided to call the cable TV systems installer s attention to Article 820 40 of the National Electrical Code The code provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of the cable entry as practical FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential or commercial installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following me
14. caption setting upon powering the TV off With this feature set to off the TV will always power on with captions disabled With this feature set to Last the TV turns on with the last caption setting l Enter the Features menu Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus 2 Press A or V to highlight Power on Caption Mode 3 Press 4 or P to select Last or Off 4 disappear Auto Power On Lock The TV will turn on and stay on whenever electrical power is applied to the set The feature is useful for controlling the TV from a wall switch or preventing the TV from being turned off by the TV power button or the remote control l 2 3 4 Enter the Features menu Press A or V to highlight Auto Power On Press lt or amp to select Disabled or Enabled Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC FOLO Queens PDI P23LCDD TV Installation Guide P s 3 of Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Inactive Power Off h mm The TV will automatically power off after a specific period of viewer inactivity providing energy savings 1 Enter the Features menu 2 Press A or V to highlight Inacti
15. in the future 1 Inthe Parental Control menu press A or V to highlight Parental Lock 2 Press 4 or gt to select Enable or Disable 3 Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear Power on Channel Displays a certain channel each time the TV is turned on This feature is useful for hospitals that have a Welcome Channel and wish to have it displayed upon the initial use of the TV The patient can then tune to any other available channel Power on Channel m Free m Basic m Premium Position A V Exit SETUP Enter the Channels menu Press A or V to highlight Power on Channel Press to select it Press A or V to highlight the desired Service Level Free Basic or Premium Press lt or gt to scroll through the channels currently available in the Service Level or Last NOTE Last will cause the TV to turn on to the last channel before it was turned off Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear p Bo qo E Channel Lock Locks the currently viewed channel and prevents patients from tuning to any other channel This feature is useful when the TV is used for information display purposes 1 Enter the Channels menu 2 Press A or V to highlight Channel Lock 3 Press 4 or P to select Enable or Disable 4 Press the SETUP button to return to the previous menu To exit press SETUP un
16. makes no representation or warranties with respect to the accuracy or completeness of the contents of this manual and specifically disclaims any implied warranties or merchantability or fitness for any particular purpose and shall in no event be liable for any loss of profit or any other damages The information contained herein is believed to be accurate but is not warranted and is subject to change without notice or obligation Trademarks Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories All other brand names and product names used in this manual are trademarks registered trademarks or trade names of their respective holder PDI and Better Solutions Are Within Reach are registered trademarks of PDI Communication Systems Inc Springboro Ohio LOCATION GUIDELINES The model PDI P23LCDD Hospital Grade LCD TV is a specialized LCD TV This TV is intended for entertainment and educational purposes for use in a hospital a nursing home a medical care center or a similar health care facility in which installation is limited to a non hazardous area in accordance with the National Electrical Code ANSI NFPA 70 The PDI P23LCDD is designed for mounting to PDI manufactured mounts Installation of the TV on any other mount is not recommended WARNING The TV s VESA mounting holes are designed for M4 metric screws only Use of a non PDI approved mount or SAE A hardware could res
17. APO means the TV will turn off if there is no video 5 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear NOTE For PC ANALOG see your computer manual for display resolution adjustments See PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 36 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Power On Source The TV can be preset to power on to a selected source 1 Enter the Sources menu 2 Press A or V highlight Power On Source 3 Press 4 or gt to change to the source that you want the TV to power on to NOTE The source must be enabled before it can be chosen as a power on source The Last entry causes the TV to power on to the Last source selected 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear FM Radio You can listen to FM radio stations that are combined with the cable TV signals using this TV FM Radio Confirm FM Radio Auto Program m Auto Program m Confirmation m Frequency m Add Delete Position A V Exit SETUP Next 4 Exit SETUP Auto Program This will search for active radio stations to program into the P23 s FM tuner 1 Press A or V to highlight FM Radio 2 Press P to enter it 3 P
18. D196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide P2ge 23 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Add Delete Channels Individual analog TV channels that are missing can be manually added to a Service Level Free Basic or Premium Analog channels that require deletion can be manually removed from a Service Level Digital channels found during auto programming can be enabled or disabled in each Service Level Add Dice ORANG EeuIEe Teel Signal Cable STD m Free Programmed Auto Program m Basic Blank gt Add Delete Channels m Premium Blank gt Clear Service Level Copy Service Level Parental Control Power on Channel Channel Lock Disabled Channel Memory Override Enabled Position AV i C C C C Position A V Exit SETUP Exit SETUP Next lt gt Enter the Channels menu Press A or V to highlight Add Delete Channels Press to select it Press A or V to highlight the Service Level Free Basic or Premium Press to select the highlighted Service Level If you want to add or delete an analog channel press lt or to select the desired analog channel If you want to enable or disable digital channels go to step 10 Add Delete Channels m Analog Channel m Add Delete Analog Channel m Enable Disable Digital Channel QU yr Position A V Exit SETUP Next 4 a After you have selected the desired an
19. Disabled to require the activation of the external sources by pressing the remote s or the TV s TV AV button Set this feature to Enabled to allow access to external devices by pressing the channel up or down buttons on a remote or most pillow speakers 1 Enter the Features menu 2 Press A or V to highlight Channel to Other Source 3 Press 4 or gt to select Enabled or Disabled 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide P2ge 35 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Power on ARC Mode The TV powers on with a set screen sized aspect ratio of 4 3 14 9 16 9 16 9 Panorama or Last 1 Enter the Features menu 2 Press A or V to highlight Power on ARC Mode 3 Press P to select 4 3 14 9 16 9 16 9 Panorama or Last 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Standby Power Setting the TV to Low makes the TV Energy Star qualified However it takes longer to power on 1 Enter the Features menu 2 Press A or V to highlight Standby Power 3 Press to select Low or Normal 4 Press SETUP to return to the previous menu To exit press SETUP until the prog
20. Download the firmware you need and save it to your desktop NOTE Please contact technical support if you have issues downloading the latest firmware Open the zip file you just downloaded and open the PDITDF folder on the USB drive Drag the firmware file to the PDITDF folder Remove the USB drive from the computer Insert it into the cloning port of the P23 See Connections diagram on page 10 When the cloning menu appears press A or V to highlight Upload Firmware to TV Press and an Upload Firmware to TV menu appears Automatic uploads the latest version stored on the USB drive If there is more than one firmware version on the USB drive the Digital Firmware menu item allows you to choose the version Press A or V to highlight the option you want Press to select it PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Page 40 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Automatic Upload Firmware to TV Upload Firmware to TV Digital Firmware version in TV v1 04 m Upload v1 05 m Upload v1 06 Upload the latest version of all firmware to TV Back lt 4 Ware Position A V Next gt 14 Press the A direction button in the Automatic Upload Firmware to TV menu to begin uploading the latest firmware Or
21. G INSTRUCTIONS TV Rating Most TV programs are now rated TV Rating allows the TV to selectively present only programming content that is unblocked per its preset level A program that is blocked displays a black screen only TV Rating ALL FV V SL D U Position A V Exit SETUP Next lt gt 1 From the Parental Control menu enter the TV Rating menu Press A or V to move to one of the six age based categories 3 Press 4 or f to cycle through the sub ratings ALL FV V S L or D or exit out of them in that category NOTE The U or B unblocked or blocked will turn red when it is highlighted 4 Press A or V to change the sub rating 5 Press the SETUP button to return to the previous menu Or press lt to get out of the sub category NOTE Categories that are rated for older audiences will be automatically blocked If you block TV Y category then TV Y7 will be blocked automatically Similarly if you block TV G category then TV PG TV 14 and TV MA will also be blocked TV Parental Guideline Rating System Meaning Young Children Content not offensive to most viewers Considered suitable for children over 7 may contain Children 7 and over Fantasy Violence Scenes Parental Audience Considered suitable for all audiences children may watch unattended Suggested Unsuitable for younger children may contain Parental Guid CUTS Suggestive Dialog Bad Language Sex and Violence Scenes Parents Strongly Unsu
22. OPERATING INSTRUCTIONS Table of Contents Warnings ep E NE 2 Safety INStrUCHONS MH E 3 FCC Copyright Disclaimer and Trademarks sininen neiaa ANAVEN anaE AVANE rtn einn rte nint sete nnt seen EEEREN EA 4 Location Guideline S Airinnis p a E 4 OSBPD dre E em UM AM 4 ec 4 Product ACCOSSOMIOS M 7 Wall Ier Ton ilaTo c EEE 8 Across Room Wirlng uio epe epe creta cotta dee dye An curie gere eo dye aenea nes Puede etu degree dye ea pde ba ber p Aan 9 Connections uusss 10 Antenna ANT Connection 441 Pillow speakers wi seen 12 Programming Remote Control iare er terere e ee elon cd aa iadaaa di eee de da eodeni eoe gb rares Aa 13 Patient Remote Control Programming tee egre uiu te m H Brightness Contrast Color Tint and Sharpness 17 Color Temperature cccccccecsceeeeeneeeseeeeeteeeeeeneeeeeas 218 PC Analog HDMI Picture and Component Input Picture 18 eom EE 19 Balance 19 Minimum Vol
23. alog channel press A or V to highlight Add Delete Analog Channel Press lt or gt to select Added or Deleted 9 Ifyou are done press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear If there are more analog channels to be added or deleted repeat steps 6 through 8 For enabling or disabling digital channels go to the next step 10 Press A or V to highlight Enable Disable Digital Channel ge PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 24 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS 11 Press to select Enable Disable Digital Channel NOTE f there are not any channels programmed in the Service Level No Channels Present will appear in the menu 12 Press A or V to highlight the digital channel that needs to be enabled or disabled Enable Disable Digital Channel Enable Disable Disable Disable Disable Enable Enable Position AV Exit SETUP 13 Press 4 or gt to select Enable or Disable 14 Press the SETUP button to return to the previous menu Clear Service Level This empties a service level of all its programmed channels leaving it blank Clear Service Level Signal Cable STD m Free Programmed Auto Program m Basic Blank Add Delete C
24. anty period PDI will repair or replace goods returned to its Springboro Ohio location at its discretion free of charge to the original purchaser the whole or any component part of any product manufactured by PDI and found by PDI to be defective As a condition to obtaining warranty service written notification must be received by PDI within at least ten 10 days after defect is first observed Repair of said product requires it to be shipped to the PDI factory in Springboro Ohio All shipments shall be F O B Springboro Ohio and all shipping and freight charges to PDI s factory shall be paid by the customer This warranty shall not apply to any PDI products subjected to improper use negligence or accident nor to tampering alterations or repairs by others without PDI s specific prior written authorization For information regarding authorized servicing and all other information pertaining to this warranty please contact PDI COMMUNICATION SYSTEMS Inc at 40 Greenwood Lane Springboro Ohio 45066 or phone 937 743 6010 This warranty gives specific legal rights and you may also have other rights which vary from state to state PDI s liability under this warranty is limited to repair or replacement of defective products and parts as provided above PDI shall not be liable for incidental or consequential damages The warranty contained herein is in lieu of all other expressed or implied warranties including any implied warranty of me
25. asures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help MAINTENANCE AND SERVICING Never remove the back cover of the TV this can expose you to high voltage and other hazards If the TV does not operate properly unplug it and call an authorized service center or PDI CLEANING AND DISINFECTION Clean the exterior of this television by removing dust with a lint free cloth CAUTION To avoid damage to the surface of the television do not use abrasive or chemical cleaning agents Spot test a new disinfectant by applying a test cleaning a non obvious small spot on the TV s back cabinet keypad and LCD panel Allow the disinfectant to soak per its instructions and then wipe clean Do not use the disinfectant if the TV s surfaces show any sign of discoloration or softening PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC r LJ Communication PDI P23LCDD TV Installation Guide Pase 3 0f 42 Systems Inc Better Solutions Are Within Reach M INSTALLATION and OPERATING INSTRUCTIONS SERVICE INSTRUCTIONS CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric
26. ault solid translucent transparent flashing Edge Style default none raised depressed uniform left drop shadow right drop shadow PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Page 33 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Digital Mode Time Setup The current time will be set automatically from a digital channel signal provided by a broadcasting TV station Digital Mode Time Setup m Time Zone Eastern m Daylight Savings Auto Position A V Exit SETUP Next lt gt Enter the Features menu Press A or V to highlight Digital Mode Time Setup Press to select it Press lt or to select your viewing area time zone Pacific Alaska Hawaii Newfoundland Atlantic Eastern Central or Mountain Press A or V to highlight Daylight Savings Press 4 or gt to select Auto On or Off depending on whether or not your viewing area observes Daylight Savings Time 7 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Bor exta PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Page 34 of 42
27. csececccccaceeecesaceccastens scenes csddecescdecansdedzcescaaeesseccceacecsecaudsczccecescdesaesccieczaneutersizacdesid 42 PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC r L I Communication PDI P23LCDD TV Installation Guide Pase 7 0f 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Product Accessories Included with TV Not Included with TV 100mm VESA Wall Mount PD168 103 74 to 6 Pin Jumper Cable PD106 416 Programming Remote Control PD108 420 74 to Jumper Cable PD106 417 Patient Remote Control PD108 421 TV Stand PD133 645 PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rr Lo 1 Communication PDI P23LCDD TV Installation Guide P3564 Systems Inc Better Solutions Are Within Reach M INSTALLATION and OPERATING INSTRUCTIONS Wall Mounting NOTE Across Room Wiring may need to be completed before mounting TV See Across Room Wiring diagram on page 9 1 Refer to Figure 1 Select a location on the wall approximately 7 72 inches below the ceiling NOTE DO NOT locate AC Across Room Wiring and CATV Signal outlets below the Wall Bracket s location as it will cause clearance issues and interfere with the TV s cabinet when mounted to the
28. ction of the correct signal type is required for the TV to recognize all possible channels and before any channel programming can begin Enter the Channels menu Press A or V to highlight Signal 3 Press 4 or P to select Air Cable STD Cable IRC or Cable HRC NOTE Most hospitals use the Cable STD signal style 4 Now perform Auto Program or Add Delete Channels to store channels in the TV s memory PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 22 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Auto Program The TV automatically scans each available channel for activity Channels that display activity are memorized into the selected Service Level Signal Cable STD Mode Digital Only Auto Program Channel Sequence Interleave A D Auto Delete Channels Add Digital Signal None Clear Service Level Free Programmed gt Copy Service Level Basic Blank Parental Control Premium Blank Power on Channel Channel Lock Disabled Channel Memory Override Enabled Position AV Position A V Exit SETUP Exit SETUP Next lt gt After setting Signal press A or V to highlight Auto Program Press to select it 3 On Mode press lt or P to select the scope of channel scanning Analog Only TV searches for analog channe
29. e are 6500K and 9300K Temperature Clock Phase ARC H Position V Position Clock Clock adjustment is used to minimize any vertical bars or stripes visible on the screen s background Adjustment of the clock setting also changes the horizontal screen size Phase The phase adjustment removes any horizontal noise and is Auto i helpful in sharpening text characters ARC Aspect Ratio Control Select the ratio of the screen size Horizontal Vertical 4 3 14 9 or 16 9 H Position Horizontal Position The H Position moves the Position A V Exit SETUP Next lt gt picture left or right on the screen V Position Vertical Position The V Position moves the picture Enter the Pichire meni up or down on the screen Press A or V to highlight PC Analog HDMI Picture AUTO Automatic adjustment of screen position clock and phase Access the menu by pressing gt Press A or V to highlight and select one ofthe settings Press lt and gt to adjust the setting See description of settings above Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear AWRWNS PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 42 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS
30. e blade or the third prong are provided for your safety If the Servicing is required when the apparatus has been provided plug does not fit into your outlet damaged in any way such as power supply cord or consult an electrician for replacement of the plug is damaged liquid has been spilled or objects obsolete outlet have fallen into the apparatus the apparatus has been 10 Protect the power cord from being walked on or exposed to rain or moisture does not operate normally pinched p at plugs convenience h i d receptacles and the point where they exit from the or has been dropped apparatus 15 Use only PDI mounts and appropriate hardware Failure to do so could cause the set to fall and subsequent injury or death PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 x Document Number PD196 158 DOC r LOI Communication PDI P23LCDD TV Installation Guide Pase 40f42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Copyright PDI Communication Systems Inc claims proprietary right to the material disclosed in this user manual This manual is issued for user information only and may not be used to manufacture anything shown herein Copyright 2009 by PDI Communication Systems Inc All rights reserved Disclaimer The author and publisher have used their best efforts in preparing this manual PDI Communication Systems Inc
31. enus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rr L P Communication PDI P23LCDD TV Installation Guide P 2e 28 of 42 Systems Inc Better Solutions Are Within Reach M INSTALLATION and OPERATING INSTRUCTIONS Motion Picture Association of USA MPAA Rating System Grade Meaning General Audiences Content not offensive to most viewers Parental Guidance Content is such that parents may not want their children to view the PG P y Suggested program PG 13 Parental Strongly Program is inappropriate for preteens with a greater degree of Cautioned offensive material Suggested than a PG rated program P E Not for children under age 17 Restricted viewing Strong elements of sex and or violence No Children under Not for children under age 17 under any circumstances Neg age 17 Strong sexual content X Hard Core Films Same as NC 17 rating No Rating MPAA Not Rated Change Password The Parental Control access password can be changed using this menu NOTE The factory default password that is programmed into the TV is 0000 Change Password m Enter Password m Confirm Password Exit SETUP 1 From the Parental Control menu enter the Change Password menu 2 Enter a new password by using the number buttons on the remote 3 Confirm the password by entering the same digits NOTE After conf
32. g Main Menu will appear See Connections diagram on page 10 4 Press A or V to highlight Save Settings to USB Press to display the Save Settings to USB menu Cloning Main Menu Save Settings To USB m Restore Settings to TV m Save a Save Settings to USB m P23LCDD tdf a Upload Firmware to TV m Clear Filename m Information Position AV Position AV 6 Ifyou want to rename the file press the A or V to highlight the file name Otherwise go to step 7 a Press lt or gt to highlight each character b Press A or V to change each character c Repeat this process until you have the desired file name Up to 8 characters may be used d When done press lt until the characters are no longer highlighted 7 Press A or V to highlight Save 8 Press to download the TV s setup to the USB thumb drive A progress screen will be displayed PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC FOLO comis PDI P23LCDD TV Installation Guide se 50 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS 9 Press 4 to return to the Cloning Main Menu 10 Remove the USB drive to return to normal TV operation Restore Setting to TV m Restore Settings to TV gt m P23LCDD tdf 1 Press A or V to highlight Restore Settings to TV 2 Press P to display a list of previously stored TV setups
33. gramming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 32 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Digital Captions Customization of Closed Captions on ATSC QAM channels Digital Captions Font Size Default Font Style Default Foreground Color Default Background Color Default Edge Color Default Foreground Opacity Default Background Opacity Default Edge Style Default Position A V Exit SETUP Next lt gt 1 Enter the Features menu 2 Press A or V to highlight Digital Captions 3 Press P to select it 4 Press A or V to highlight the attribute you wish to change 5 Press to change it See the table below for the attributes of each setting 6 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Setting Attributes Font Size default small standard large Font Style default sizes 0 through 7 Foreground Color default white black red green blue yellow magenta cyan Background Color default white black red green blue yellow magenta cyan Edge Color default white black red green blue yellow magenta cyan Foreground Opacity default solid translucent transparent flashing Background Opacity def
34. h between TV and FM 15 SAP button Radio sources Adjust audio mode MTS 7 SLEEP button Stereo Mono or SAP Sets the sleep timer 16 SSM button ds 8 LAST button Adjust sound setting for content Return to previously viewed type User Flat Speech Movie channel or Music 9 VOL 4 buttons 17 Number buttons Raises or lowers volume Use to directly enter channels 0 Also used to navigate 9 programming menus 18 DASH button 10 OKbutton Use to enter second part of a Confirms the current channel digital channel selection 19 Teletext buttons 11 CH A Y buttons Navigates teletext displays Selects next channel Also Teletext is not actively used in the used to navigate USA programming menus PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC r Lo m Communication Systems Inc Better Solutions Are Within Reach Patient Remote PD108 421 PDI P23LCDD TV Installation Guide Peze 14 of 42 INSTALLATION and OPERATING INSTRUCTIONS POWER button Turns the TV on or off MUTE button Turns the sound on or off TV AV button Selects enabled external inputs TV FM button Switches between TV and FM Radio sources SLEEP button Sets the sleep timer Increments of 10 minutes up to 120 LAST button Return to previously viewed channel VOL 4 buttons Decreases or increases the volume OK button Confirms t
35. hannels m Premium Blank gt Clear Service Level Copy Service Level Parental Control Power on Channel Channel Lock Disabled Channel Memory Override Enabled Position A V Exit SETUP Next lt gt Exit SETUP Enter the Channels menu Press A or V to highlight Clear Service Level Press to select it Press A or V to highlight the Service Level Free Basic or Premium Press to select the highlighted Service Level A confirmation page will appear Press A to proceed Press V or SETUP to return to the previous menu NOTE Afier a Service Level is cleared the TV returns to the Clear Service Level menu Blank will appear to the right of the Service Level 7 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear QUU Fe X Ears PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm I Communication PDI P23LCDD TV Installation Guide Page 25 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Copy Service Level This copies one Service Level s channels to another Copy Service Level Signal Cable STD m From Free To Basic gt Auto Program Add Delete Channels Clear Service Level Copy Service Level Parental Control Power on Channel Channel Lock Disabled Channel Memory Override Enabled Adiust From
36. he current channel selection CH A V buttons Selects next or previous channel 10 12 13 14 15 ARC button Changes the aspect ratio Repeatedly press the ARC button to select your desired picture format See page 41 for instructions on adjusting picture up or down CC button Cycles through Closed caption choices SAP button Adjust audio mode MTS Stereo Mono or SAP Number buttons Use to directly enter channels 0 9 DASH button Use to enter second part of a digital channel CODE button The remote offers independent Bed A or Bed B selectable codes and independent control of a single TV in a two TV room Insert a paperclip in this hole to select Bed A or Bed B PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Page 15 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Programming The PDI P23LCDD TV is programmed by a series of menus that can be accessed with a programming remote part number PD108 420 Access the menus by pressing SETUP on the remote These menus allow you to add TV channels adjust the picture and sound setup external components and change settings Service Level Picture Sound Channels Features OSD Language Sources FM Radio Position A V Exit SETUP Next lt gt
37. in Upload Firmware to TV press A or V to highlight the desired version of firmware Then press in the Upload Firmware to TV menu to begin uploading the new firmware 15 A message on the black screen will indicate when the upload is complete After the upload is complete remove the USB drive 16 After the uploading process is complete turn the TV off and then on to return to normal viewing mode NOTE The TV will take a few minutes to upload the new version of firmware PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm Li Communication PDI P23LCDD TV Installation Guide Pese 4 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Appendix ARC vertical adjustments The on screen image in certain aspect ratios can be moved up or down The Aspect Ratio is adjusted by pressing the ARC button on the remote 1 Press ARC button on the remote repeatedly until you come to the desired aspect ratio that will allow you to move the image up or down on the screen EE Position 2 2 Press A or V to adjust the position 31 to 31 3 Press ARC button to exit PC Analog HDMI Picture Adjustment of a computer s picture can be made only when the TV is in PC Analog or HDMI mode PC Analog HDMI Picture Temperature Temperature is a measure of the warmth of an image The two temperatures availabl
38. irming the password the TV will return to the Parental Control menu Block Aux Source Like TV programs and channels the auxiliary sources can be blocked too When the TV encounters an external signal source that is not appropriate per its settings a black screen appears with muted sound NOTE Parental Lock must be enabled for the sources to be blocked See Parental Lock on page 29 1 Inthe Parental Control menu press A or V to highlight Block Aux Source 2 Press 4 or gt to select Unblocked or Blocked 3 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Parental Lock Duration This sets how long an enabled Parental Lock will be active 1 Inthe Parental Control menu press A or V to highlight Parental Lock Duration 2 Press 4 or gt to select the desired number of hours 1 99 or Always 3 Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide P2ge 29 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Parental Lock This enables or disables the settings in the Parental Control menu Enabling it will require the password to be entered to access the Parental Control menu
39. itable for children under 14 may contain Cautioned Strong Dialog Bad Language Sex and Violence Scenes Mature Audience Adults only may contain Strong Dialog Bad Language Sex and Only Violence Scenes PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 27 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS The sub rating of TV rating Grade Meaning FV Fantasy Violence Violence Sexual Situation Adult Language Sexual Suggestive Dialog MPAA Rating Most televised movies are now rated MPAA Rating selectively allows the TV to only present movie content that is unblocked per its preset level MPAA Rating G Unblocked PG Unblocked PG 13 Unblocked R Unblocked NC 17 Unblocked X Unblocked No Rating Unblocked Position A V Exit SETUP 1 2 From the Parental Control menu enter the MPAA Rating menu Press A or V to highlight a particular MPAA Rating 3 Press 4 or gt to select Blocked or Unblocked NOTE Parental Control will automatically block any category that is rated for older audiences For example if you block the PG 13 category then R NC 17 and X will be automatically blocked also 4 Press SETUP to return to the previous menu To exit press SETUP until the programming m
40. itional channels beyond those offered in the FREE level PREMIUM This is the highest service level with typically the most channels available for viewing PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC r L21 Communication PDI P23LCDD TV Installation Guide Pese 17 of 42 Systems Inc Better Solutions Are Within Reach M INSTALLATION and OPERATING INSTRUCTIONS Picture This menu allows you to make changes to settings that will change the picture s appearance Brightness Contrast Color Tint Color Temperature Sharpness PC Analog HDMI Picture Component Input Picture Noise Reduction Enabled Position A V Exit SETUP Next lt gt Press the SETUP button on the remote control 2 Press A or V to highlight Picture 3 Press PF to enter the Picture sub menu Brightness Contrast Color Tint and Sharpness These settings have a range of 1 100 To change one of them change the number by following this process Enter the Picture menu Press A or V to highlight the setting you want to change Press 4 or gt to set the desired number Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear qupd PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rm LI Communication
41. ls only Digital Only TV searches for digital channels only Analog and Digital TV searches for both analog and digital channels 4 Press A or V to highlight Channel Sequence 5 Press 4 or P to select the channel sequence in which the channels are displayed nterleave A D Channels are displayed in the order of channel number All A then D All digital channels are displayed after all analog channels 6 Ifyou want to allow the TV to program additional digital channels Press A or V to highlight Add Digital Signal Press lt or gt to select Air NOTE This feature is only available if Mode is set to Digital Only or Analog and Digital 7 Press A or V to highlight the Service Level Free Basic or Premium you wish to program The menu displays the current programming status of each level as either Programmed or Blank NOTE A programmed service level can also be reprogrammed if desired 8 Press to start auto programming 9 A confirmation menu will appear before proceeding Press A to start auto programming Press V to cancel the operation The TV now will search all available channels Auto programming requires several minutes to complete NOTE Digital channel auto programming may take longer than 10 minutes to complete 10 Press the SETUP button to return to normal TV viewing NOR PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number P
42. on the USB thumb drive 3 Press A or V to highlight the desired setup file 4 Press P to select it 5 A confirmation screen will appear Press A to restore the selected setup file or press lt to return to the previous menu without restoring A progress screen will appear as the settings are restored 6 The TV will return to the Cloning Main Menu after restoring is complete 7 Remove the USB thumb drive PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 x Document Number PD196 158 DOC d Communication PDI P23LCDD TV Installation Guide Pese 39 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Information This allows you to check what version of firmware the TV is using a Digital Firmware v1 06 1 Inthe Cloning Main Menu press A or V to highlight Information 2 Press P to display screen 3 Press 4 to return to the previous menu Firmware The firmware for the model PDI P23LCDD TV is field upgradeable A data file is written to a USB thumb drive connected to the TV s USB interface cable and updated using the TV s menus Once complete the TV settings must be reprogrammed One a dB Insert a USB thumb drive into a computer Create a new folder on the drive called PDITDF if one does not already exist Open your web browser and go to http www pdiarm com support Click on Firmware and Driver Updates
43. r L i Communication PDI P23LCDD TV Installation Guide Pase 0f 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Installation and Operating Instructions P23 Hospital Grade TV Model PDI P23LCDD NK NKP WI Communication Better Solutions Are Within Reach Systems Inc 40 Greenwood Lane Springboro Ohio 45066 PH 937 743 6010 FX 937 743 5664 http Avww pdiarm com PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC r LOI Communication PDI P23LCDD TV Installation Guide Pase 2 0f 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS WARNINGS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock DO NOT remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel This symbol is intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons OVERHEAD FALLING HAZARD TV can pose a striking hazard when mounted at an elevated position Use only PDI mounting
44. ramming menus disappear On Screen Menu Language Selection You can adjust the language used in displaying the OSD on screen display Press SETUP 2 Press A or V to select the OSD Language menu 3 Press 4 or gt to select your desired language English Francais Espanol 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Sources The TV s signal sources can be individually Enabled or Disabled The available sources in this menu correspond with the components you have connected to the TV s connectors See page 10 for a diagram of connections NOTE Please disable all of the TV s sources that are not being used A TV that is switched to a non connected source generates nuisance hospital maintenance calls of TV Not Working when in fact the TV does work but has been set to an inactive source Sources TV Enable APO Composite Video Enable APO S VIDEO Enable APO Component 1 Enable APO Component 2 Enable APO HDMI 1 Enable APO HDMI 2 Enabled APO PC ANALOG Disabled FM RADIO Enabled Power On Source Last Position A V Exit SETUP Next lt gt From the SETUP menu press A or V to highlight Source Press lt or gt to select it Press A or V to highlight a desired source Press lt or gt to change the source status to either Disabled or Enabled APO Auto Power Off NOTE Sources that are gray are not installed in the TV For the TV source Enabled
45. rchantability or fitness for any particular purpose PDI neither assumes nor authorizes any person to assume on its behalf any other obligation or liability Some states DO NOT allow the exclusion of limitation of incidental or consequential damages or a disclaimer of warranties implied by law so the above limitation or exclusion may not apply The information and technical data in this manual is believed accurate but is not warranted and is subject to change without notice or obligation PDI and Better Solutions Are Within Reach are registered trademarks of PDI Communication Systems Inc Copyright O 2004 2009 by PDI Communication Systems Inc All rights reserved PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC
46. ress A or V to highlight Auto Program 4 Press P to select it 5 A confirmation page will appear Press A to proceed Press V or SETUP to return to the previous menu Add Delete Stations 1 Press A or V to highlight Frequency 2 Press 4 or gt to select the frequency you wish to add or delete 3 Press A or V to highlight Add Delete 4 Press 4 or gt to select Added or Deleted NOTE When you return to the normal viewing screen a station you deleted will be playing Press A or V to tune to another station Now the station is deleted 5 Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC P EON PDI P23LCDD TV Installation Guide Pese 37 0f42 Systems Inc Better Solutions Are Within Reach M INSTALLATION and OPERATING INSTRUCTIONS Cloning Cloning allows quick programming of a TV from a USB thumb drive The cloning operation involves first downloading setup information from a programmed host TV to a USB thumb drive and then uploading the setup information to another TV Cloning also can be used to re program a programmed TV Save Settings to USB 1 Using a computer create a folder called PDITDF on a USB thumb drive 2 Turnon the TV 3 Insert the USB thumb drive into the cloning port in the back of the TV A Clonin
47. s designed to work with either a digital pillow speaker that generates digital style control codes or a single button analog switch style pillow speaker A rear panel mounted switch allows use of different brands of pillow speakers and supports the major brands Zenith Philips and RCA pillow speakers Please refer to the Pillow Speakers section on page 11 for details Optional Jumper SPEAKER PD106 417 DATA SWITCH SPEAKER COMMON Optional Jumper PD106 416 DATA SWITCH ACROSS ROOM WIRING PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC Communication m i LA Systems Inc Better Solutions Are Within Reach Connections PDI P23LCDD TV Installation Guide Page 10 of 42 INSTALLATION and OPERATING INSTRUCTIONS o p og ec M hag ra 1 AC INPUT AC power cord connection 2 AN IN Connect these outputs to the Audio Video inputs of external equipment NOTE Connections are color coded 3 S VIDEO IN If the external equipment you are connecting has an S VIDEO jack you can use an S VIDEO cable for improved picture quality NOTE Audio connections are color coded 4 COMPONENT2 IN and 5 COMPONENT1 IN The TV supports two inputs for devices such as a DVD that offer Component type signals NOTE Some device s Y Pb Pr connections might be labeled as Y Cb Cr or Y
48. shock do not perform any servicing other than contained in the operating instructions unless you are qualified to do so PRODUCT MODIFICATION Do not attempt to modify this product in any way without written authorization Unauthorized modification could void the user s authority to operate this product Important Safety Instructions Important safeguards for you and your new product 1 Read these instructions 11 Only use attachments accessories specified by the 2 Keep these instructions manufacturer 3 Heed all warnings 4 Follow all Re tulis 12 Use only with the cart stand 5 Do not use this apparatus near water tripod bracket or table 6 Clean only with dry cloth specified by the manufacturer 7 Dono block any ventilation openings Install in or sold with the apparatus accordance with the manufacturer s instructions When a cart is used use 8 Do not install near any heat source such as caution when moving the cart radiators heat registers stove or other apparatus t bination t ae including caplet that produces heat ule RM d 9 Do not defeat the safety purpose of the polarized avoid injury from tip over or grounding type plug A polarized plug has 13 Unplug this apparatus during lightning storms or when two blades with one wider than the other A unused for long period of time grounding type plug has two blades and a third 14 Refer all servicing to qualified service personnel grounding prong The wid
49. the TV is allowed to reach Enter the Sound menu 2 Press A or V to highlight Maximum Volume 3 Press 4 or P to select the desired number 0 100 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Power On Volume Sets the initial volume for when the TV is turned on NOTE f Power on Volume is set to Last and the physical power was removed the TV will power on with a volume of 0 Enter the Sound menu 2 Press A or V to highlight Power On Volume 3 Press 4 or gt to select the desired number 0 100 or Last NOTE Power On Level can only be set between Minimum Volume setting and Maximum Volume setting Last will cause the TV to be at the last volume setting before it was turned off 4 Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide P2ge 20 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Internal Speaker Enabled This allows audio for different sources to be enabled Sound is also routed externally to the attached pillow speaker NOTE This only affects the internal speakers The pillow speaker will always have sound Internal Speaker Enable TV Free Service Level Enabled
50. til the programming menus disappear Channel Memory Override Allows a channel to be entered with the remote s number buttons that is not memorized in the current Service Level Enter the Channels menu 2 Press A or V to highlight Channel Memory Override 3 Press 4 or gt to select Enabled or Disabled DISABLED Service Level Channels only ENABLED All possible channels 4 Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC Communication i LV P Systems Inc Better Solutions Are Within Reach M Features The Features menu provides adjustable settings that customize the TV to your hospital Power on Caption Mode Auto Power On Lock Inactive Power Off h mm Bed A B Caption Text Modes Digital Captions Digital Mode Time Setup Diagnostics Channel Up Power Off Channel To Other Sources Power on ARC Mode Standby Power Position A V Exit SETUP 1 2 3 Press the SETUP button PDI P23LCDD TV Installation Guide Pase 30 of 42 INSTALLATION and OPERATING INSTRUCTIONS Last Enabled Disabled A Disabled Disabled Disabled 16 9 Low Next lt gt Press A or V to highlight Features Press to enter the Features sub menu Power on Caption Mode Power on Caption Mode memorizes the
51. ult in a condition where the TV could unexpectedly fall and cause injury or death The PDI P23LCDD TV mounts to the wall typically at the foot of a patient s bed with the supplied bracket Select a location that is near an AC wall outlet and that does not expose the TV to bright room lights or sunlight if possible The LCD TV also requires connection of both CATV cable signal and across room wiring for the pillow speaker OSHPD State of California Only The combined weight of the PDI P23LCDD TV and PDI wall mount is less than 20 pounds At the time of this writing the involvement of a written submitted reviewed and approved plan by OSHPD is not required to install the PDI P23LCDD TV in the state of California Energy Star The PDI P23LCDD TV is ENERGY STAR qualified in its factory default setting PDi pe Communication an Energy Star Partner has determined that this product meets energy efficiency guidelines Changes to certain features settings and functionalities of the TV can change the amount of power it consumes The changes could possibly PARTNER set the amount of power consumption beyond the limits required for ENERGY STAR qualification PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 lt Document Number PD196 158 DOC rf LJ Communication PDI P23LCDD TV Installation Guide Pase 5 0f 42 Systems Inc Better Solutions Are Within Reach M INSTALLATION and
52. ume ERR 19 Maximum Bol Uode DT E EAEE EI E AEEA E E AEAEE AN AA EEEN 19 Power on Volume 19 Internal Speaker Enabled 20 HDMI 1 amp 2 Audio Port 2 20 Composite S Video Sound Mode 20 Channels tette ceesene x21 Ir Me c 21 PAULO Progra susien e raaa AITEN 22 Add Delete Channels 2229 Clear Service Level 24 Copy Service LOVeGl e 25 Parental Control REM 25 WAM Rating acre etes 26 TV Parental Guideline Rating System The sub rating of TV rating MPAA Rating iccirco egere Yat d e dae dida 2227 Motion Picture Association of USA MPAA Rating System 28 Change Password E 28 BIOCK AUX SOURCE DRITTER IDEE 28 Parental Lock Duration 29 Parental Lock 29 Power on Channel 29 Channel Lock 29 Channel Memory Override 29 ug MEE 30 Power On Caption Mode 2 2 eevee eret dene edge ede Cede deed dre Vetra adaa iadaaa ed De Edd pe ded addons 30 Auto Power On Lock 90 Inactive Power Off h mm 31 Bed AB cct M mA MM EUEE 31 Caption Text occ M es 31 Digital Captions
53. ve Power Off h mm 3 Press 4 or gt to select an active time or select Disabled to disable this feature 4 Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear NOTE Auto Power On must be set to Disabled for this function to operate Bed A B The TV can be controlled by a patient IR remote PD108 421 The TV offers Bed A and Bed B selectable codes for independent control of a single TV in a two TV room The patient remote can be toggled between Bed A and Bed B codes by pressing the CODE button with a paperclip 1 Using programming remote PD108 420 enter the Features menu 2 Press A or V to highlight Bed A B 3 Press 4 or P to select A or B 4 Press the SETUP button to return to the previous menu To exit press SETUP until the programming menus disappear Try the patient remote PD108 421 to make sure it works with the Bed setting 6 fit does not insert a paperclip into the CODE button at the bottom of the remote and hold it in for a few seconds 7 Try the remote again ijo Caption Text Modes Teletext can be displayed in addition to Captions Teletext is not normally broadcast in the USA Caption Text Modes should be set to Disabled for TVs operated in the USA 1 Enter the Features menu 2 Press A or V to highlight Caption Text Modes 3 Press 4 or gt to select Disabled or Enabled 4 Press SETUP to return to the previous menu To exit press SETUP until the pro
54. w speaker is possible 1 Select the appropriate brand of digital pillow speaker using the recess slide switch next to the PILLOW jack CZ for Zenithe CP for Philipse CR for RCAe OFF to disable the pillow speaker For analog style pillow speakers set the switch to CZ CP or CR CAUTION Confirm the pillow speaker type and set the side switch appropriately BEFORE connecting the pillow speaker to the TV Failure to follow this procedure could result in damage to the pillow speaker or cause improper operation of the TV NOTE The TV is shipped from the factory with the switch in the OFF position 2 Connect the pillow speaker to the PILLOW jack 3 Operate the pillow speaker and verify correct control PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 1 937 743 6010 PH 1 937 743 5664 P Document Number PD196 158 DOC rm LI Communication PDI P23LCDD TV Installation Guide Pese 2 of 42 Systems Inc Better Solutions Are Within Reach INSTALLATION and OPERATING INSTRUCTIONS Buttons on TV There are buttons on the front of the P23 that allow basic operation of the TV 1 2 3 4 5 6 7 1 Power Indicator 4 Y CH A Channel Down Up Illuminates in red when the TV is off Selects the previous next channel Used to navigate menus llluminates in green when the TV is switched 5 lt VOL Volume Decrease Increase on Adjusts the volume Used to navigate menus 2 Power ON OFF 6 TV
Download Pdf Manuals
Related Search