complete sand filtration with six-way valve and pump
Contents
1. FILTERING TANK AND SIX WAY VALVE 1 Filling of the sand filtering medium The sand filtering medium is filled through the filter s upper opening a Release the tank branch plastic plugs b Protect the inner tube against infiltrating sand using a plastic cover c We recommend that you fill in the tank with water up to a half to ensure a damping effect after filtering sand is filled in This will protect the bottom drainage duct against an excessive impact d Carefully fill in adequate quantity and type of filtering sand Make sure that the central tube is in the middle of the opening The sand surface should be levelled and should reach up to approximately a half of the filtering sand Remove the plastic cover from the inner tube 2 Connect the control valve to the filtering tank a Insert the control valve with a correctly fitted sealing ring to the tank nozzle and ensure that the central tube connects to the opening in the bottom part of the valve b Place two plastic plugs on the valve flange and the tank nozzle and tighten them to ensure that the valve can rotate on the tank for the purpose of the final adjustment in a permanent position p C BRILX N e SWIMMING POOL EQUIPMENT SJ c Carefully fasten the pressure gauge with a correctly fitted sealing ring in the valve opening with an inside thread Do not over tighten d Use hose to connect the pump to the control valve opening identified PUMP After connecting tig2. Conditions of guarantee abide by the trading and guarantee conditions of your supplier Secure disposal of the product after the lifetime expiry After the lifetime expiry ensure its ecologic disposal made by a skilled company Complaints and customer service Complaints abide appropriate consumer protection rights In the event of unrecoverable defect please address the written complaint to your supplier Supplier
3. O ring of the cover on 3 Ensure the assembly on the body by screws of the cover Tighten them equally and alternatively Do not over tighten EE C BRIL X N m mm SWIMMING POOL EQUIPMENT Z WARNING e Turn the pump off before changing the position of the six way valve e Do never operate this installation without water e Do never connect the filter directly to the water source from the water supply system Water pressure from the water supply system might be much higher that the maximum pressure of the filter e Do never turn the pump on if the position on the six way valve is set on closed position or if pipes of the circulation system are impassable There is a risk of a higher pressure than the working pressure which can lead to the damage disruption separation of the six way valve cover that might cause injuries or deterioration of assets e It is not permitted to sit on or burden the installation e Do not clean the filter cover nor the filter container with a solvent it could damage its surface tarnishing transparency etc e Clean regularly the capillary filter of the pump and the skimmer basket in order to prevent the damage of the pump and ensure the proper operation of the system e Do not screw out flanged connectors if the pump is running e All connectors are equipped with the padding therefore there is no need to screw the nuts too tightly it could damage the plastic components Conditions of guarantee
4. back to the bottom part of the container Through the regulating valve the water comes back to the pool by hoses The whole process is continuous and automatic It ensures the complete re circulation of the pool water through the filter and the hose system After some time of operation the dirt accumulated in the filter may cause upsetting of water conduit through the sand and reduce he flow through the filtration unit This process indicates to the fact that the filter should be cleaned If you set the valve bar in the position BACKWASH the water flow will automatically return so it will flow from the bottom of the container through the filtration sand from which it rinses the sedimen tary dirt to the waste pipe If the filter is rinsed set the bar in set the bar in the position RINSE and activate the pump for a half to one minute then set up the valve stick back to the position FILTER to re initiate the standard filtration II Installation e Assemble the filtering system including the pump the filtering tank and the six way valve e The filtering system should be fitted as close to the pool as possible possibly 0 5 metre under the water level in the pool Make sure that water can run off from the place where the filter is installed PUMP 1 The pump and the electric power line should only be installed by qualified and authorized persons All pumps are supplied with 230 V power 2 Remember to fit in a closing valve in the suction line
5. COMPLETE SAND FILTRATION WITH SIX WAY VALVE AND PUMP ON BASE PLATE Models FSP350 FSP450 FSP500 FSP650 INSTALLATION AND USER GUIDE Please read the user manual EM Content I PUL CUION ssptonnena mnanaa II T stallati oikeen ann MI Main proportions ccccessseeeeees IV Installation starting up the filtration V List of filtration components VI List of six way valve components VII List of pump components VII Functions of six way valve and meaning of its positions of the equipment or unwanted injury BRILX SWIMMING POOL EQUIPMENT Thank you for choosing our product and for trusting our company Please read the instructions carefully and follow the steps indicated in our user guide before the initiation of this product in order to avoid the damage p C BRILX N m pmm SWIMMING POOL EQUIPMENT I Function The filter uses a special filtration sand to capture the dirt components from the pool water A filter container operating as a permanent dirt collector is filled with the filtration sand When the regulating valve remains in the position FILTER the pool water containing the dirt sucked through the system of hoses is auto matically forced in the regulating valve with patented filter and it is led from this place to the top part of the filtration container The water pushed through the sand removing the fine dirt is taking
6. ate the pump and let it run for about half a minute to one minute until the water in the aperture is not clean Turn the pump off set the valve back in the position FILTER and re activate the pump The filtration is running now in the standard filtration mode and filter off the dirt from the pool water 5 Adjust the suction and reversible valves in a way to reach the required flow Check that the water doesn t leak from the system and the filter and if necessary tighten the connections screws or nuts 6 Write down the pressure while initiating the filtration cycle when the filtration is clean This value will vary according to the pool used pump and the length and shape of pipes After some time the pressure will increase and the water flow will reduce due to the accumulation of the dirt in the filtration If the pressure gauge shows 1 5 Bar which is more than the initial pressure while the filter is clean it is time to rinse the filtration see BACKWASH in the chapter Filtration and regulating valve functions Note During the first cleaning of the new pool water there might be necessary to rinse the filtration sand more often because this water contains more dirt V List of filtration components Pressure gauge with O ring o ieem rana DO o U LJ MUNS eN ITT O BRILX SWIMMING POOL EQUIPMENT VI List of Six Way Valve Components 1 Lever 6 fowngeoer E i E a o Sorese ni
7. et 11 Filtration bag spider 12 Body diffuser 13 O ring of the end piece p C BRIL X N i pmm SWIMMING POOL EQUIPMENT VII List of Pump Components o pns e pe o o oee 44 a A Q W p C BRILX N A SWIMMING POOL EQUIPMENT J VIII Functions of Six Way Valve and Meaning of its Positions WASTE Filter bypass is used for the drain suction or lowering the water level RECIRCULATION Filter bypass for water pumping to the pool without filtration CLOSED Closing of the flow to the filter or to the pool FILTRATION WASTE CLOSED Waste Waste Waste Input Output Input Output Input Output BACKWASH RINSE RECIRCULATION Waste Waste Waste Input Output Input Output Input O utput General instructions 1 The valve stud is set for adjustable pressure gauge 2 Reparation and maintenance of the valve Before initiation of your work turn the pump off and close the valve of the suction and draining pipes a Set the bar in the position FILTER b Remove the screws from the cover c Pull and remove the cover and the valve separator set Setting up 1 Place the valve separator in a way that the separator opening is on the TOP neck lever is in the position FILTER The flat edge of the cover screw stud must be in the same level as the flat edge of the body screw stud 2 Put the
8. hten the plugs using a screwdriver and tap the screwdriver handle on the plug to ensure that the plug settles on the valve flange 3 Connect the pool tube to the control valve opening identified RETURN and complete other necessary installations and lines such as the suction pipeline to the pump drain etc 4 Ensure that all pipeline connections are duly tightened to prevent water leakage III Main proportions Maximum water temperature 40 C Maximum operating pressure 200 kPa Sand grain size 0 5 0 8 mm Table of dimensions Deen Power input Voltage discharge kW V Eon IV Installation starting up the filtration 1 Make sure there is a sufficient amount of the filtration sand in the filter container and that all necessary connections have been executed and ensured 2 Press the bar of the regulating valve and turn it in the position BACKWASH To prevent he damage on the valve scale press always the stick before turning p C BRIL X N m m SWIMMING POOL EQUIPMENT 3 Irrigate the pump and turn it on according the instructions make sure that all suction and reversing pipes are opened to fill the filtration container with water When water is running out through the waste hose leave the pump in operation at least for one minute The primary sand rinse is recommended due to the removing of the dirt and fine particles 4 Turn the pump off and set the valve in the position RINSE Activ
Download Pdf Manuals
Related Search