User Manual
Contents
1. smartphone and press to select where to share Remote Control Under standby mode press the menu button to enter system settings press the left right arrow buttons to choose remote then select Remote Match The message on the LCD Screen is Wait Remote Match and camera enters pairing mode At the same time press both buttons on the remote controller to start pairing Pairing is successful when the LCD screen shows Remote Match OK 1 Indicator light 2 Photo Button press to take photos 3 Inquiry Record Button press to start stop Press the Inquiry Record Button 3 and the Photo recording press and hold for 3 seconds to check button 2 simultaneously to enter Pairing mode the present status of the camera see below Remote Control Indicator Light Status Status LED Red LED Light Blue LED Light 1 time sec frequently Standb Off lied Flickers about 5sec Recording Off Light on 3 seconds then off Power off Light on 3 secs then off Off Long light Long light Pairing Mode Light on 3 secs then off Light on 3 secs then off Off 2 times sec frequent Off Flickers about 5sec 1 time sec frequent Off Flickers about 5sec Flashes once each time you take a photo Status Inquiry Connecting to External Devices Play back on HD TV Turn the camera on connect the HDMI port in the camera to the TV via an HDMI cable not included and choose the HDMI mode on TV The LCD screen on the camera w2. Action Sports Camera Part 9905 User Manual Please read through this user manual before using the product and keep the manual for future reference Product appearance and or specifications are subject to change without notification WASPcam is a division of 636 Distributing Inc Ariss ON 519 822 8400 TABLE OF CONTENTS System Requirements Features oo o A Installing SD Card o d 8 10 11 1 1 1 1 1 1 1 13 14 Remote Control Functions amp Indicators J Y Using the Camera s Wi Fi 13 15 7 1 1 2 2 2 3 6 7 8 Safety Precautions e Read the following guidelines before using this camera e Refer to the manual instructions to operate the camera properly Improper operation may cause damage to camera internal components e Do not store the product in dusty dirty or sandy areas as its components may be damaged e Do not leave the camera in places exposed to extremely high temperatures such as direct sunlight for extended periods of time High temperatures can shorten the life of electronic devices damage batteries and warp or melt certain plastics e Do not store the product in cold areas When the product warms up to its normal temperature moisture can form inside which may damage the electronic circuits e Do not attempt to open the casing or attempt your own repairs High voltage internal components create the risk of electric shock when exposed e Do not drop or knock the product Rough handling m
3. of upper lower case letters and numbers 4 Turn the camera on and press the menu button twice to enter system settings press the left right arrow buttons to choose WIFI and select open The WIFI icon will show onthe screen Search the Wlan using your mobile find the network name which you have set connect and enter the password XXXXXXXX whatever you saved and confirm Connection is successful when the LCD screen shows WIFI connected then open the WASPcam TACT APP and preview the camera s view take video and photos and also change menu settings directly from your smartphone to your camera such as video resolution photo size etc APP Interface Description Open WIFI and to connect click the WASPcam TACT icon to enter the APP This will show on your screen when the app is starting up F MD After connecting your smartphone will enter standby mode and live viewing screen will be showing on your phone Press this icon to switch to recording and photos Press this icon to record video or photo Press this icon to enter settings Video Resolution Photo Size Loop Recoding Record Audio Auto Off Clear Cache Wi Fi Press this icon to see all the files Press this icon to download files from the camera to smartphone Press this icon to see the files that have been downloaded to your smartphone Press this icon to change your WIFI setting Connect to the internet network and open the downloaded photo video on your
4. any language or computer language in any form or by any means electronic mechanical magnetic optical manual or otherwise without the prior written permission of the manufacturer For manuals in additional languages please visit www waspcam com
5. ay damage the internal components e Donot use harsh chemicals cleaning solvents or strong detergents to clean the product Wipe the product with a slightly damp soft cloth e Do not open the battery cover while an image is being recorded Doing so will not only make storage of the current image impossible it can also corrupt other image data already stored on file e Ifthe product or any of its accessories are not working properly please contact 636 Distributing Inc and our tech team will assist you and if necessary arrange for the product to be repaired or replaced e tis recommend to use the camera in temperatures between 0 C to 40 C e Turn off the camera before removing the memory card to avoid damaging the card or storage data e tis normal for the camera to be warm after long periods of use e Do not touch the lens while using the camera or it can affect video picture quality e Please use the air blower special lens blowing equipment to clean lens or use special lens cleaning cloth to clean fingerprint or dust on the surface e Always test for proper operation before using the camera e 636 Distributing Inc is not responsible for any damage or personal injuries resulting from the use of the WASPcam TACT or for replacing it if lost or stolen e 636 Distributing is not responsible for any legal repercussions from the use of the WASPcam TACT or from the sharing of footage System Requirements The camera requires a PC with the follo
6. box com sh o7glexh40dg6hri AAAnosSorWzAhRagI sXN p2Ha dl 0 Click download at the pop up dialog box to download wasp20150514 apk Connect mobile and computer by USB cable Copy wasp20150514 apk to your mobile Find wasp20150514 apk at your mobile Click wasp20150514 apk to install Using the Camera s WIFI Cont 2 Turn the camera on and press the menu button twice to enter system settings press the left right arrow buttons to choose WIFI SSID Press the OK button to select then press the menu button to select Del then press the Ok button to delete the WIFl name Then you can enter new a new WIFI name Press the menu button to select uppercase lowercase letters or numbers press the left right arrow buttons to choose the letters to spell the word you want then press the Ok button to confirm Press the menu button to select and Ok to confirm the setting 3 Turn the camera on and press the menu button twice to enter system settings press the left right arrow buttons to choose WIFI password Press the OK button to select then press the menu button to select Del then press the Ok button to delete the WIFI password Then you can enter anew WIFI password Press the left right arrow buttons to choose the letters to spell the word you want then press the Ok button to confirm Press the menu button to select and Ok to confirm the setting Note The WIFI name and passwords need to be at least 8 characters comprised
7. c Record to 2 mins for more options refer to Video Settings exit the menu and press the record button once to take a video The LED light between the 2 arrows will flash green and at the top of the LCD screen it displays the red flashing recording icon and the recording time 2 After 2 minutes the camera will stop recording automatically and save the video then continue recording 3 When SD card is full camera will delete the first video footage automatically and continue recording 4 At anytime during recording you can press the record button to stop and save the video The remaining time will display on the LCD screen at the top right Motion Detection 1 Press menu and use right arrow to choose Motion Detection and choose 30 SEC for example for more options refer to Video Settings press REC to enter Motion Detection mode The screen will say Motion Detecting 2 If there is movement the camera will auto record for 30sec or the time you set and stop If there is no movement the camera will stop recording automatically If there is constant movement the camera will detect this and the camera will keep recording at 30sec intervals or the time you have set Note If you need to pause recording press the record button once to stop it If you need to cancel motion detection please turn off this setting in the menu Also this setting will not work if the Cyclic Record is not turned off Image rotation Depending on th
8. confirm Press the menu button to return Menu Interface Introduction When you are in standby mode press the menu button to enter settings press the left right arrow buttons to choose the options then press the OK button to confirm press menu button again to quit Video Menu Settings Under Video mode press the menu button to enter video settings press the left right arrow buttons to choose the options then press the OK button to confirm press menu button again to quit MENU OPTION SETTINGS 1080P30FPS 720P60FPS WVGAGO FPS VGA120FPS 0 0 1 2 1 0 3 2 2 0 2 0 3 2 1 0 1 2 System Settings Under standby mode and playback mode press the menu button twice to enter the system settings press the left right arrow buttons to choose the option press the OK button to confirm press the menu button to exit settings Off 1 min 5 mins English French Spanish Portuguese German Italian WP X RaP PYCCKMN H St 101 Polski NTSC PAL Cancel Ok FWVer X X XXXX XX XX Photo Menu Settings Under Photo mode press the menu button to enter photo settings press the left right arrow buttons to choose the options then press the OK button to confirm press menu button again to quit 0 0 1 2 1 0 3 2 2 0 2 0 3 2 1 0 1 2 Using the Camera s WIFI 1 Before using this function download and install the WASPcam TACT App to your Apple iPhone iOS system smartphone or Android smartph
9. e need under the system menu Image Rotation Select Open and press OK button to confirm the screen will show inverted images This may be necessary if you are mounting the camera upside down Photos Snap Shots While you are recording video you can press the power button to take a picture Note when you are taking a snap shot video is still being recorded continuously You can only view the snap shots in browse mode 1 Normal photo Press Mode button until you see the camera icon in the top left corner The white balance exposure and ISO icons will also show on the LCD screen At the top right of the LCD screen the display shows the remaining amount of photos resolution SD Card amp battery icons Press the record button to take a photo 2 Capture Mode Single 3s 10s 30s Timer Press the menu button to enter camera settings press the left and right arrow buttons to choose capture mode and select the time press OK button to confirm press the record button and the camera will count down the time you ve selected and then take a photo Press the record button again to stop or change the capture mode to single Note when taking pictures please try to hold the camera steady or it may affect the picture quality 3 Auto Photo off 3 5 10 seconds Press the menu button to enter camera settings press the left and right arrow buttons to choose Auto Photo mode and select the time and press ok Press menu to exit Press th
10. e record button once and the camera will take a photo at the chosen interval continuously The screen will show the countdown and when the time is up the camera will take a photo automatically and then save the photo then continue photographing according to the time you set To stop please turn the auto photo setting Off 4 Sequence Off On Photo Burst Press the menu button to enter camera settings press the left and right arrow buttons to choose sequence then turn it on press OK button to confirm press Menu to exit Press the record button and the camera will take and save 3 consecutive photos To stop please change the sequence setting Off 5 Quick Review Off 2seconds 5seconds Press the menu button to enter camera settings press the left and right arrow buttons to choose Quick Review choose 2 or 5 seconds press OK button to confirm then press Menu to exit Press the record button and the camera will take 1 photo and hold it for you to preview it for 2 5 seconds according to the time you have set then it will go back to photo standby mode 6 Zoom in out While in record or photo mode you can use the left and right arrow buttons to zoom in out 7 Playback mode Under standby mode press the mode button twice to enter into playback mode the gt will be in the top left corer Press the arrow buttons to choose the file you want to review press the OK button to confirm Press again to pause then press OK button again
11. ft D Mode Button M Record Button Top Right Menu Button OK Button O Left Button G Right Button gt LED Light On Off Button To turn the camera on amp off To clear the screen To delete files under playback mode To switch to picture mode video mode and playback mode Start and stop taking photos videos Returns to the photo video mode when you are in the menu To enter exit menu settings To browse photos and videos to enter and confirm settings under setting mode Choose the last menu or file zoom in and to reduce volume under playback mode Press and hold to rewind playback video To choose the next menu or file to zoom out and to increase volume under playback mode Press and hold to fast forward playback video To turn the LED light on and switch between bright normal flashing and off BASIC CAMERA FUNCTIONS Installing the Micro SD Card 1 Inserting the SD card e With the camera off open the back cover e Press the card slot to the right e Place the SD card in the slot e Close and lock the card slot e Do the reverse to remove the SD card Note Please ensure that the SD Card is inserted in the right direction or you may damage the SD card Using the LED Lights Press the light bulb button Q above the arrow buttons to turn on the LED lights in bright mode press again for normal mode press the 3rd time to make the LED lights flash and press the 4th time to
12. ill turn off automatically and now all operations and functions can be seen on the TV Play back on TV Turn the camera on connect the camera with the AV cable to the TV choose USB mode on the TV then go into the camera menu settings and make sure the TV Out is set to open The LCD screen on the camera will turn off automatically and now all operations and functions can be seen on the TV Note TV AV cable is not included and when connected it will only transmit images videos but no sound View Files on PC MAC Connect the computer to the camera using the USB cable The LCD Screen displays Mass Storage and Camera press the left right buttons to select Mass Storage and press the record button to confirm Open the cameras hard drive and go to the CARDV folder Click on this folder and there are two sub folders MOVIE and PHOTO Select any folder to open and view the corresponding files Open the camera PC Only Connect PC with camera using USB cable The LCD Screen displays Mass Storage and Camera press the left right buttons to select Camera and press the record button to confirm Goto My Computer and you can now use the camera as a web cam Technical Specifications Lens 170 Video Format MOV Image Format JPG WF Copyright 2015 All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into
13. one Installing the WASPcam TACT App Apple iPhone iOS system Smartphone There are two ways to download the WASPcam TACT App to your iPhone 1 Download from iTunes Store through your computer s iTunes program 2 Download from the App store through your iPhone Note Before you do the following steps please confirm that your computer has the iTunes program installed and you have set up an Apple account It needs to be the Apple iOS 6 0 system or above Download from iTunes Click iTunes icon to open iTunes Click iTunes Store Icon to open the iTunes Store iTunes Store i Enter WASPcam TACT into the search bar Once it s finished the WASPcam TACT icon will show on your home screen Download by iPhone Click the App Store icon Q WASPcam TACT Click the search field and enter WASPcam TACT click the blue search button Click the icon and click download WASP LZ LE s Once it s finished the WASPcam TACT icon will show on Tar your home screen WASPcam TACT Android Smartphone Open the Google Play store on your phone Enter WASPcam TACT into the search bar and hit search i Click on the WASPcam TACT icon to view the app page TEL Click the install button to install the WASPcam TACT app to your phone s Once download is complete the WASPcam TACT app will appear in your rr application menu WASPcam TACT Android by Computer Open the computer internet and enter this link https www drop
14. to continue playing the file During Video playback press and hold the right or left arrow buttons to fast forward or reverse playback Press and hold the right left arrow buttons to stop playback ad press the right left arrows to adjust the volume Deleting Protecting Files Slide Show Deleting Files Under standby press the mode button to enter into playback mode Press the menu button to enter settings the press the left right arrows to select Delete press the OK button to confirm Press the left right arrows to Delete all or Delete Current then press the OK button to confirm Press the left right arrow buttons to choose Cancel or OK to deleting the file Press OK to confirm delete mode will exit Protecting Files Under standby mode press the Mode button to enter into playback mode Press the menu button to enter settings and press the left right arrow buttons to select the protect setting Press OK to confirm and then press the left right arrow buttons to select Lock Current Unlock Current Lock All Unlock All then press OK to confirm Press Menu button to exit Slide Show Under standby mode press the Mode button to enter into playback mode Press the menu button to enter settings and press the left right arrow buttons to select Slide Show then press the OK button to confirm Press left right arrow buttons to select 2 5 or 8 Seconds then press the OK button to
15. turn them off Charging the Battery Connect camera and power supply using USB and charger The red indicator at the front of the camera will be on while the camera is charging Once it is fully charged the red indicator light will turn off Note To improve the charging efficiency of the camera please turn the camera off while it s charging Turning the Camera On Off To turn on the camera press the power button for 3 seconds and a chime will sound the WASPcam TACT screen will turn on and the red indicator light at the front of the camera will also turn on To turn off the camera press the power button again for 3 seconds until the chime sounds and the screen goes black At the left of LCD screen it displays the video icon loop recording icon white balance icon and audio record icon At the right of LCD screen it displays the remaining recording time resolution SD card icon and battery icon on the bottom of the LCD screen it displays date and time Recording Functions Normal Recording Turn on the camera and press the record button once to take video and the green LED light between the arrows will flash and the recorded time and recording icon are displayed on the top of LCD screen Press the record button again to stop recording and save the file then remaining recording time is displayed at the top of LCD screen Loop recording 1 Turn on the camera press the menu button and use the right arrow to choose Cycli
16. wing specifications for full HD 1080p 30fps and 720p 60fps playback Windows 8 Windows 7 Vista XP SP2 MAC OS X 10 5 and later Intel AMD Dual Core CPU and later At least 1 GB of RAM or higher At least DirectX 9 video card DirectX 10 is recommended Standard USB 1 1 port and later At least 2GB or greater available hard disk space Features The camera offers a variety of features and functions including Full HD 1080p 30fps H 264 Video Clip 170 Wide Angle Lens WLAN 802 11 b g n 2 4GHz RF remote control 12 Megapixel Photos Li ion Rechargeable Battery Smartphone App Supported WASPcam TACT App ACCESSORIES The following items should be in your the package If any items are missing or damaged contact your dealer immediately Bar Mount User Manual 3M Stickers Curved Mount w 3M Tape Li lon Battery Wrist Remote Camera Function Quick Guide Diagram Refer to the following illustrations to familiarize yourself with the buttons and controls of this camera Record Button a Power Button i A Indicat LED Lights j USB amp HDMI Ports Rs Back Panel Lock Mode Button A _ LED On Off Button a Wa Se Ne 0 pappa Menu Button AN I Left Button indicator OK Button Right Button i Indicator LCD Screen Battery Compartment SD Card Slot Back Cover en at BUTTON FUNCTIONS Power Button Top Le
Download Pdf Manuals
Related Search