DAC-9013-R User Manual
Contents
1. 4 DAC 9013 R SDI to Analog Composite Component Video Converter with Reclocked Outputs User Manual IROSS Video Production Technology DAC 9013 R User Manual Ross Part Number 9013RDR 004 02 Release Date October 23 2012 The information contained in this manual is subject to change without notice or obligation Copyright O 2012 Ross Video Limited All rights reserved This work is proprietary and confidential to Ross Video Limited its subsidiaries and its other affiliated corporations and may not be copied distributed sold or otherwise used or relied upon without the express written permission of Ross Video Limited Reproduction or reverse engineering of copyrighted software is prohibited Patents This product is protected by the following US Patents 4 205 346 5 115 314 5 280 346 5 561 404 7 034 886 7 508 455 7 602 446 7 834 886 7 914 332 This product is protected by the following Canadian Patents 2039277 1237518 1127289 Other patents pending Notice The material in this manual is furnished for informational use only It is subject to change without notice and should not be construed as commitment by Ross Video Limited Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual Trademarks ROSS 15 aregistered trademark of Ross Video Limited Geartite is a trademark of Ross Video Limited Ross ROSS ROSS a2. a e e Figure 7 DAC 9013 R Fine Phase Potentiometer Setup Iss 02 14 Configuration The DAC 9013 R includes Function Select 16 position rotary switch that enables you to select specific functions and their options This switch works in conjunction with the Down and Up buttons to configure the DAC 9013 R to convert SDI signals to analog video signals This section provides information on configuring the DAC 9013 R using this switch and buttons Refer to Function Down Button Select Up Button Figure 8 DAC 9013 R Switch and Button Locations General Operating Rules Please note the following important operating rules for the DAC 9013 R For each of the supported Video Standards NTSC PAL B PAL N the card stores the default video settings independently in non volatile memory The module always powers up in the last configuration used Always check to see that the inputs are valid and the correct Video Standard has been selected from the Function menu Function Selection Start by setting the Function Select switch to Position 0 and adjust your video input to the correct SDI Video Standard NTSC 525 60 PAL B 625 50 PAL M 525 50 PAL N 625 60 Note that NTSC 525 60 is the default standard Refer to the section Function Setup and Configuration Menus on page 16 for complete settings information Example Configuration 1 Toconfigure the Format function Tum the Function
3. 16 Table 2 Function Setup and Configuration Menu Function LED Display Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN Position CVBS Y C Output Video YUV Format RGB SMPTE EBU N10 YUV MII Format Betacam x1 5 x1 to x1 5 x1 x0 to x1 x0 x1 x0 to x1 x0 x2 x1 to x2 x1 x0 to x1 x0 Chromas and burst On O O e Chromas and burst Off 17 7 Configuration Iss 02 Table 2 Function Setup and Configuration Menu Function LED Display Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN UP Position 22 5 From 0 to 22 5 0 From 0 to 22 5 22 5 22 5 From 0 to 22 5 Sub carrier Phase 0 From 0 to 22 5 22 5 Setup 15 From 0 to 15 IRE Black Level 0 IRE From 0 to 7 5 IRE ol 7 5 e x O OC e 0 0 Clip below 1 5 IRE Superblack Clip below 6 IRE Clip Level Clip below 11 IRE Pass all Narrow Blank VI Blanking O ej O Normal Pass Configuration Iss 02 18 Table 2 Function Setup and Configuration Menu Function LED Display Selection Function Up Down Buttons Mode Switch Me
4. The DAC 9013 R can be mounted in any convenient location However to ensure long life for this product observe the following precautions and operating requirements Maintain an ambient temperature of 20 C to 40 C Allow for air circulation around the chassis for convectional cooling Many different mounting positions are possible with the included mounting hardware Some installation options are permanent and require careful consideration of the final positioning before installation Please note that in some mounting locations the power adaptor must be affixed in a similar manner as the chassis Other possible options include the use of adhesive magnetic sheets not included affixed to the chassis and the power adaptor for removable mounting on metal cabinets etc Cable ties may be necessary in some applications to relieve strain on the mounting hardware and the connectors Surface Mount Strips The included VELCRO brand surface mount strips allow the GearLite module and power supply to be affixed to a permanent location during use and easily Installation Iss 02 8 removed for adjustments Carefully consider the installation location before proceeding adhesive is very aggressive and is not easily removed The adhesive will cure fully in 24 hours To install the Surface Mount Strips 1 Remove the Protective Backing Film from the adhesive on the bottom of the two VELCRO brand Surface Mount Strips 2 Adhe
5. 3 Flat Metal Plate Installation Option 3 Install the chassis in the desired location using the Mounting Holes on the Flat Metal Plate Mounting screws are not provided by Ross Video Angle Mounting Bracket The Angle Mounting Bracket Figure 4 allows a single GearLite module to be installed in positions not possible with the flat metal plate The bracket has a 90 angle Mounting screws are not provided by Ross Video Installation Iss 02 10 0 Figure 4 Angle Mounting Bracket 11 Installation Iss 02 Setup Power Adapter and Supply Connect PS 9000 power adaptor to power supply connector The PS 9000 provides up to 2A of regulated 5V DC 5 The DC power cord has a locking connector that securely fastens into the power supply DC jack on the DAC 9013 R The DAC 9013 R has a standard miniature power jack center pin positive If using an adaptor other than the PS 9000 ensure that the polarity is correct the voltage is 5V DC regulated to 5 sufficient current for the DAC 9013 R is supplied Caution Use of improper adaptors may damage the DAC 9013 R N and will void the warranty Installations outside of North America using line voltages of 200 240V require a plug certified for the country of use to be installed on the supplied line cord Refer to the section Important Regulatory and Safety Notices to Service Personnel at the front of this manual for details Cable Connection
6. Contact Us section on last page of this manual GearLite products are covered by a generous 3 year warranty and will be repaired without charge for materials or labor within this period See the Warranty and Repair Policy section in this manual for details Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources Ross Video encourages you to use the appropriate take back systems These systems will reuse or recycle most of the materials from your end of life equipment in an environmentally friendly and health conscious manner The crossed out wheeled bin symbol invites you to use these systems If you need more information on the collection reuse and recycling systems please contact your local or regional waste administration You can also contact Ross Video for more information on the environmental performances of our products Introduction Overview The DAC 9013 R SDIto Analog Composite Component Converter with Reclocked Outputs is a high quality signal conversion solution for SDI signals and part of a growing family of GearLite self contained small brick format modules The DAC 9013 R addresses program stream imaging
7. power cord from being walked on or pinching particularly at plugs convenience receptacles and point where they exit from the apparatus Warning Indoor Use WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Do not block ventilation openings Install in accordance with manufacturer s instructions Do not install near heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not use this apparatus near water Only use attachments accessories specified by the manufacturer Unplug this apparatus during lightning storms or when unused for long periods of time Clean only with a dry cloth To avoid electrical shock disconnect the A C power cord before any servicing Refer all servicing to qualified personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug damage liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped EMC Notices United States of America FCC Part 15 This equipment has been tested and found to comply with the limits for a class A Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This
8. Select switch to Position 1 The default configuration is CVBS Y C The DOWN LED will be lit and UP LED will be lit to indicate CVBS Y C configuration selection 15 Configuration Iss 02 2 To change Format configuration to RGB Keep the Function Select in Position 1 Press the Up button once The DOWN LED will be unlit and the UP LED will be lit to indicate RGB configuration selection 3 Tochange the Format configuration to YUV Keep the Function Select in Position 1 Press the Down button once to return to default configuration Press the Down button again to scroll down to YUV The DOWN LED will be lit and the UP LED will be unlit to indicate YUV configuration selection Function Setup and Configuration Menus A single press of the Down and Up buttons is a momentary click of the button unless indicated by h Table Legend Press the Up button from the default position Press the Down button from the default position Hold Up or Down button for 2 3 seconds forfaster adjustment or special function Factory default state Lit LED display e Unlit LED displav Xt Flashing LED display Table 2 Function Setup and Configuration Menu Function LED Display Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN UP Position NTSC 525 Input Video Sendai PAL B G 625 PAL N 625 Configuration Iss 02
9. Sync 300mV UV Levels 700mV Y Video 700mV YUV SMPTE EBU N10 525 or 625 Y Sync 300mV U V Levels 700mV a Other U V levels may be obtained by adjusting Menu items 4 and 5 Specifications Iss 02 22 Service Information Warranty and Repair Policy The GearLite DAC 9013 R is warranted to be free of any defect with respect to performance quality reliability and workmanship for a period of THREE 3 years from the date of delivery to the customer In the event that your GearLite DAC 9013 R proves to be defective in any way during this warranty period Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics Should you find that this GearLite DAC 9013 R has failed after your warranty period has expired we will repair your defective product should suitable replacement components be available You the owner will bear any labor and or part costs incurred in the repair or refurbishment of said equipment beyond the THREE 3 year warranty period In no event shall Ross Video Limited be liable for direct indirect special incidental or consequential damages including loss of profits incurred by the use of this product Implied warranties are expressly limited to the duration of this warranty This GearLite DAC 9013 R User Manual provides all pertinent information for the safe installation and operation of your GearLi
10. equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense approved by Ross Video Limited could void the user s authority to Notice Changes or modifications to this equipment not expressly operate this equipment CANADA This Class A digital apparatus complies with Canadian ICES 003 Cet appariel numerique de la classe A est conforme a la norme NMB 003 du Canada EUROPE This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive 93 68 EEC INTERNATIONAL This equipment has been tested to CISPR 22 1997 along with amendments A1 2000 and A2 2002 and found to comply with the limits for a Class A Digital device Notice This is a Class A product In domestic environments this product may cause radio interference in which case the user may have to take adequate measures Maintenance User Serviceable Parts Routine maintenance to this GearLite product is not required This product contains no user serviceable parts If the module does not appear to be working properly please contact Technical Support using the numbers listed under the
11. is not locked input signal conflicts with the setting of Menu item 0 loss of power to the DAC 9013 R When lit this LED indicates a valid input signal is present and no errors are detected The DAC 9013 R is functioning correctly STATUS Flashing When flashing green this LED indicates an input signal problem or an inconsistency between the SDI input standard and the selected output format Green When unlit this LED indicates a loss of power to the Of DAC 9013 R Yellow For menu items that have multiple selections these LEDs will be in a state as indicated in the Function Yellow Setup and Configuration Menu a A valid signal is defined as any analog composite video signal standard input into the DAC 9013 R which matches the setting of the Video Standard that has been selected in the Function Setup and Configuration Menu In other words if the converter is in its default state for NTSC 525 60 video then only an NTSC 525 60 composite video signal input will cause the OK LED to be lit Any other analog composite video signal of a different standard PAL B PAL M PAL N that is input into the converter will be invalid Fine Phase Adjustment The Fine Phase Adjust potentiometer located at the front panel of the DAC 9013 R allows the analog output to be moved approximately 18 5ns approximately 24 3 58MHz Figure 7 illustrates the potentiometer location Fine Phase Adjust U U
12. it to help reduce the effects of jitter on the SDI input signal being passed on to the analog composite outputs In situations where the SDI input signal may have high amounts of jitter it is recommended that the PLL be enabled The PLL may be disabled if the user would prefer to have the analog composite output reflect the SDI input jitter The PLL is locked to the SDI input signal Disruptions of the SDI input i e untimed switches may cause the output to be disrupted In cases where the output of a router or other serial digital switch is required to be converted it is recommended that an SDI synchronizer such as the RossGear DVB 8020A S be used upstream immediately before the DAC 9013 R Status LEDs The front edge of the DAC 9013 R has four LED indicators that display the status of the input signals and indicate menu function and configuration selections Figure 6 REFERENCE LED U U e KEN e NE STATUS LED Figure 6 DAC 9013 R Front Edge Status Indicator LEDs Table 1 describes the status LEDs available on the DAC 9013 R Note that the DAC 9013 R is operating correctly when the REFERENCE and STATUS LEDs are continually lit 13 Setup Iss 02 Table 1 Status LED Descriptions Function When lit this LED indicates that a reference input signal is present and locked When unlit this LED indicates a reference input signal REFERENCE error such as a l missing input signal input signal
13. nd MLE are registered trademarks of Ross Video Limited e VELCRO is a registered trademark of Velcro Industries B V All other product names and any registered and unregistered trademarks mentioned in this manual are used for identification purposes only and remain the exclusive property of their respective owners Important Regulatory and Safety Notices to Service Personnel Before using this product and any associated equipment refer to Important Safety Instructions listed below to avoid personnel injury and to prevent product damage Product may require specific equipment and or installation procedures to be carried out to satisfy certain regulatory compliance requirements Notices have been included in this publication to call attention to these specific requirements Symbol Meanings Protective Earth This symbol identifies a Protective Earth PE e terminal which is provided for connection of the supply system s protective earth green or green yellow conductor This symbol on the equipment refers you to important operating and maintenance servicing instructions within the Product Manual Documentation Failure to heed this information may present a major risk of damage or injury to persons or equipment Warning The symbol with the word Warning within the equipment manual indicates a potentially hazardous situation which if not avoided could result in death or serious injury Ca
14. nu Selection Menu DOWN UP Position Odd Field Even Field 22 22 22 21 Start of 21 21 Up button requires a 1 second button press Default Reset All Down button requires a 1 second button press a In CVBS or RGB modes Position 2 has no effect and both LEDs will be off b Hue and Sub carrier Phase apply to CVBS mode only 19 Configuration Iss 02 Specifications Technical Specifications Specifications are subject to change without notification Table 3 DAC 9013 R Technical Specifications Category Serial Digital Video Inputs Analog Reference Analog Composite Output Parameter Number of Input Signals Specification Signal Standards Accommodated SMPTE 259M 270Mbps Input Impedance 75ohm terminating Return Loss gt 19dB to 270MHz Equalization Signal Standards Automatic up to 26dB 200m of Belden 8281 cable 270Mbps NTSC SMPTE 170M 1999 PAL B G ITU R BT 470 6 Input Impedance 750hm Return Loss Number of Outputs gt 37dB to 5MHz 3 Video Composite Analog Video Y C or RGB or YUV Supported Composite Formats NTSC NTSC EIAJ PAL B PAL G PAL N Output Impedance 750hm Output Return Loss gt 45dB to 5MHz Output Isolation gt 44dB to 5MHz Signal Level Refer to Table 4 on page 22 DC Offset for RGB
15. or Composite Video lt 50mV Frequency Response 0 25dB to 5 5MHz Sub carrier Jitter lt 0 5 typical Thermal Stability lt 0 1 C Specifications Iss 02 20 Table 3 DAC 9013 R Technical Specifications Category Parameter Specification Analog Composite Output Other Timing Adjustment 18 5ns Group Delay lt 20ns to 4 2MHz Differential Phase lt 0 7 Differential Gain lt 0 5 Outputs Short Circuit Protected Path Length SDI input to Composite output Yes 2 3us typical RMS Noise unweighted Require Voltage lt 57dB 0 5MHz 5V DC 5 regulation Current Consumption lt 640mA typical Total Power Thermal Environment 3 2W typical 20 C to 40 C 68 F to 104 F ambient non condensing Dimensions approx 13cm x 9cm x 2 5cm 5 x 3 5 x 1 Weight approx 21 Specifications Iss 02 312g 110z Analog Video Levels Table 4 Analog Video Levels Video Format Standard Levels NTSC Composite PAL B G Video PAL N Video Level 714mV Sync Level 286mV Video Level 700mV Sync Level 300mV Y Video 714mV YUV Betacam Y Sync 286mV U V Levels 934mV Y Video 700mV YUV Betacam Y Sync 300mV U V Levels 1000mVa Y Video 700mV Y Sync 300mV U V Levels 648mV YUV Y Video 700mV Y
16. re the Surface Mount Strips to the bottom side of the chassis Figure 2 e SURFACE MOUNT STRIPS SERIAL NUMBER LABEL PROTECTIVE BACKING FILM Figure 2 Surface Mount Installation Option 3 Remove the Protective Backing Film from the other side of the VELCRO brand Surface Mount Strips 4 Press the chassis into position on the surface you want to mount it to Operating Tip An additional VELCRO brand Surface Mount Strip is available to mount the power adapter Non Slip Pads Four non slip adhesive pads have been supplied for desktop placements Simply remove the protective backing film from the adhesive and affix one non slip pad to each of the four corners on the bottom of the chassis Optional Mounting Accessories Ross Video is committed to providing practical solutions for the needs of your high quality broadcast facility 9 Installation Iss 02 Flat Metal Plate Use the flat metal plate for permanent mounting to a rack a desk or any other location where bolts or screws can be applied Be sure to position the module to allow for operator adjustments if required To install the Flat Metal Plate 1 Remove 2 screws from the bottom of the chassis 2 Install the Flat Metal Plate onto the bottom of the chassis Figure 3 using the screws provided in the Mounting Kit Do not use the screws removed during Step 1 SERIAL NUMBER LABEL FLAT METAL PLATE MOUNTING HOLES Figure
17. requirements by converting 10bit SDI video to analog composite video CVBS or analog component video RGB or YUV Y C outputs are also supported The DAC 9013 R has a full 10bit data path and a reference input for color framing NTSC and PAL B G only The front panel of the DAC 9013 R chassis provides an Input Status LED and a Reference LED for visual reference In addition user selectable settings are available for proc amp controls The GearLite DAC 9013 R provides conversion of 525 and 625 SDI signals SMPTE 259M NTSC PAL and PAL N standards are supported Component levels can be set to Betacam MII or SMPTE standards The DAC 9013 R also has two reclocked SDI outputs Special measures have been taken to ensure excellent return loss at both input and output The DAC 9013 R includes a universal power adaptor and line cord suitable for the country of use Various mounting options are included that allow a wide range of installation choices The DAC 9013 R provides a flexible high quality SDI conversion solution in a small stand alone package Simplified Block Diagram RECLOCKED SDI SDI OUT 1 pee ee See ee Soe eee ee eee eee SDI OUT 2 EQUALIZER amp ANLG C V R OUT DESERIALIZER no MATRIX MULTIPLIERS ENCODER amp DIA CONVERTERS 10BIT ANLG Y U B OUT COLOR BLACK REFERENCE IN FRAMING p ANLG cvasiviG OUT SEQUENCER Figure 1 Simplified Block Diagram of DAC 9013 R Functions In
18. s Overview Connect the cables to the DAC 9013 R according to the designations indicated on the chassis label and Figure 5 The input is internally terminated at 75ohm It 15 not necessary to terminate unused outputs SDI OUT 2 Y U B OUT REF IN 99696963 SDI OUT 1 C V ROUT CVBS YIG OUT Figure 5 DAC 9013 R Connections Input and Output Signal Details The DAC 9013 R accommodates a SMPTE 259M C SDI input signal The input is equalized reclocked and then de serialized to 10bit parallel data This data stream is encoded to composite video or scaled and converted to the selected component format YUV or RGB The digital data is then converted to Setup Iss 02 12 analog using 10bit DACS The DAC 9013 R enables the userto adjustanumber of parameters Such as video level hue etc The DAC 9013 R also has an input for an analog composite reference signal This reference signal must comply with either SMPTE 170M 1999 or ITU R BT 470 6 The reference signal is used to determine in which color field the output should be for composite output only This color framing circuit works in NTSC and PAL B G modes Note that the reference signal and the SDI input to the DAC 9013 R must be co timed The color framing circuit identifies Color Field 1 on the reference input The next SDI odd field will be set to Color Field 1 on the analog encoded output Phase Locked Loop Circuit The DAC 9013 R incorporates a high quality PLL circu
19. te Product Ross Video policy dictates that all repairs to the GearLite DAC 9013 R are to be conducted only by an authorized Ross Video Limited factory representative Therefore any unauthorized attempt to repair this product by anyone other than an authorized Ross Video Limited factory representative will automatically void the warranty Please contact Ross Video Technical Support for more information In Case of Problems Should any problem arise with your GearLite DAC 9013 R please contact the Ross Video Technical Support Department Contact information is supplied at the end of this publication A Return Material Authorization number RMA will be issued to you as well as specific shipping instructions should you wish our factory to repair your GearLite DAC 9013 R If required a temporary replacement module will be made available at a nominal charge Any shipping costs incurred will be the responsibility of you the customer All products shipped to you from Ross Video Limited will be shipped collect The Ross Video Technical Support Department will continue to provide advice on any product manufactured by Ross Video Limited beyond the warranty period without charge for the life of the equipment 23 Service Information Iss 02 Notes Service Information Iss 02 24 Notes 25 Service Information Iss 02 Notes Service Information Iss 02 26 A Contact Us Contact our friendl
20. troduction Iss 02 6 Features The DAC 9013 R includes the following features NTSC PAL PAL N operation 10bit DAC e 10bit data processing e 2 reclocked SDI outputs YUV or RGB or CVBS YC e User adjustable Proc Amp Color framing of analog composite output signal e Color bar test signal with valid SDI input Normal or narrow Vertical Interval Blanking on composite output Axover sampling 54MHz 5V universal adapter with locking DC connector Separate status and reference LEDs Excellent I O specifications Small brick form factor 5V universal adapter with locking DC connector 3 year warranty 7 Introduction Iss 02 Installation Static Discharge Whenever handling DAC 9013 R and other related equipment please observe all static discharge precautions as described in the following note to sensitive semiconductor devices Avoid handling circuit boards in high static environments such as carpeted areas and when wearing synthetic fiber clothing Always exercise proper grounding precautions when working on circuit boards and related equipment ESD Susceptibility Static discharge can cause serious damage Unpacking Unpack each DAC 9013 R module you received from the shipping container and check the contents to ensure that all items are included If any items are missing or damaged contact your sales representative or Ross Video directly Mounting and Installation
21. ution The symbol with the word Caution within the equipment manual indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Warning Hazardous Voltages This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons ESD Susceptibility This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event bb b b B Important Safety Instructions 1 10 11 12 13 14 15 Warning Read these instructions Keep these instructions Heed all warnings Follow all instructions The safe operation of this product requires that a protective earth connection be provided A grounding conductor in the equipment s supply cord provides this protective earth To reduce the risk of electrical shock to the operator and service personnel this ground conductor must be connected to an earthed ground Do not defeat the safety purpose of the grounding type plug A grounding type plug has two blades and a third grounding prong The third prong is provided for your safety If the provided plug does not fit in to your outlet consult an electrician for replacement of the obsolete outlet Protect the
22. y and professional support representatives for the following Name and address of your local dealer Product information and pricing Technical support Upcoming trade show information Telephone Technical After Hours Emergency Support i Email Telephone General Fax Information Email Website Visit Us Visit our website for Company information and news 1 613 652 4886 1 613 349 0006 techsupport rossvideo com 1613 652 4886 1 613 652 4425 solutions rossvideo com http www rossvideo com Related products and full product lines Online catalog Testimonials ROSS Video Production Technology
Download Pdf Manuals
Related Search