Manual
Contents
1. 4 Installing the Converter For as a standalone unit Verify the AC DC adapter conforms to your country AC power requirement and insert the power plug Connect the media cable for network connection For as a slide in unit gt The slide in Media Converter and Converter Rack should be supplied only from the same source both Media Converter and Rack are built to match on dimensions DC jack receptacle and power safety Turn off the 19 converter rack power Ensure that there is no activity in the network Locate 5VDC power jack on converter back carefully slide in and plug to 19 rack 5VDC power receptacle Connect the media cable for network connection Turn on the converter rack power the Power LED will light up Fiber Port Attach the fiber cable The Tx Rx fiber cable must be paired at both ends TP Port Attach UTP Cat 3 or 5 cable to TP port MPR To a Hub or Repeater DTE _ Toa workstation or NIC Slide switch DTE MPR is on the side panel Default MPR BNC Port Attach T Connector to BNC port and connect the RG 58 coaxial network Ensure the coaxial cable segment is terminated at both ends properly UU Note a b Use the straight through cable Cable pin outs for RJ 45 jack 1 2 3 6 to 1 2 3 6 MPR Default To a Hub or Repeater DTE Toa workstation or NIC DTE pin outs are crossover on board already Configure the MPR DTE slide switch on the side panel f2. 0Mbps at half duplex e LED Indicators FL Link Act TP Link Act Col Power e Power Requirement LA 5VDC e Ambient Temperature 0 to 50 C e Humidity 5 to 90 e Dimensions 26 2 H x 70 3 W x 94 D mm Note Connecting to Router Bridge or Switch please refer to the device s Technical Manual 6 __TP Fiber Technical Specifications 8 TP BNC Technical Specifications e Standards EEE802 3 10Base T 10Base 2 TP Port RJ 45 jack with a slide switch for MPR or DTE selection BNC Port BNC connector Cable and Distance Cat 3 5 unshielded or shielded twisted pair UTP STP wire maximum length 100 meters 328ft 0 2 inch diameter RG 58A U 50Q ohm coaxial cable maximum length 185 meters 607ft Data Transfer Rate 10Mbps at Half duplex mode LED Indicators BNC Act TP Link Act Col Power Power Requirement 1A 5V Ambient Temperature 0 to 50 C Humidity 5 to 90 Dimensions 26 2 H x 70 3 W x 94 mm D 9 DC Power Jack and AC DC Power Adapter The DC jack s central post is 2 5mm wide it conforms to the DC receptacle 2 5mm on the 19 inch Converter Rack slot DC Jack Keep the AC DC adapter as spare lt 2 5mm parts when Media converter is installed DC Input in a 19 inch Media Converter Rack 1A 5V AC DC power adapter AC Input 100 240VAC 50 60Hz DC Output 1A 5VDC
3. 1 Overview Checklist TEEE802 3 10Mbps Ethernet TP Fiber Converter TP BNC Converter User s Manual 620 0012 000 1 Overview IEEE802 3 10Mbps Ethernet supports various type media for network connection such as 10Base 2 10Base T and 10Base FL The media converter is used to convert one type media signal to other type equivalent that allows multiple type segments connect easily and inexpensively The converters can be used as a standalone unit or as a slide in module to the 19 converter rack up to 10 units for use at a central wiring closet 2 Model Description Model Connector Type TP FL RJ 45 lt gt 820nm ST multi mode TP BNC RJ 45 lt BNC 3 Checklist Before you start installing the Converter verify that the package contains the following The Converter AC DC Power Adapter This User s Manual T Connector for TP BNC Converter model only Please notify your sales representative immediately if any of the aforementioned items is missing or damaged 2_Front and Rear Panel 10Mbps TP to Fiber Converter Front and Side Panel Ethernet Converter 10Base T FL FL TP OO ac OO Col Pwr TX 3 Installation JOOUL Q DTE MPR O 10Mbps TP to BNC Converter Front and Side Panel Ethernet Converter 10Base T 2 BNC TP C OO ad Oo BNC Cal Pwr JUQUU O DTE MPR O
4. or cable connection to a Hub or NIC Network interface Card 4 NWay Device connection LED Description 5 Connecting to 10 100Mbps NWay Device rter Model 10 100 NWay Inter operating TP Fiber Converter 10 100Mbps is auto sensing and comes to 10Mbps Half duplex TP BNC Converter 10 100Mbps is auto sensing and comes to 10Mbps Half duplex 6 LED Description TP Fiber Converter LED Color Function Collision Power TP BNC Converter Lit when Fiber connection is good Blinks when any FL traffic is present Lit when TP cable connection is good Blinks when any TP traffic is present Blinks when any collision is present Lit when 5V power is coming up Function BNC Act Blinks when BNC traffic is present TP Link Act Collision Am Power Green Lit when TP connection is good Blinks when TP traffic is present Blinks when any collision is present Lit when 5V power is coming up 5 _TP Fiber Technical Specifications 7 TP Fiber Technical Specifications e Standards JEEE802 3 10Base T 10Base FL TP Port RJ 45 jack with a slide switch for MPR or DTE selection Fiber Port The 10Mbps Fiber Transceiver ST multi mode l 820nm Default e UTP Cable Cat 3 or 5 cable up to 100m Fiber Cable 50 125 62 5 125 or 100 140 4m multi mode 10Mbps Fiber Cable Limitations Fiber Multi mode 2Km e Data Transfer Rate 1
Download Pdf Manuals
Related Search