SUNNY CENTRAL 500HE-US - Unpacking / Technical
Contents
1. NOTICE The straps are under tension and spring back when removed Cuts by straps springing back will result Wear personal protective equipment Keep safety distance to the straps 1 Cut through the straps with a knife 2 Remove the straps A WARNING Danger of crushing Damage of the Sunny Central will result The cabinets of the Sunny Central are no longer secured and they could fall off the pallet during transport Do not transport the Sunny Central on the pallet 3 Remove the cardboard which was underneath the straps 4 Remove the pieces of wood underneath the roof M The straps have been removed 18 SC500HE US_Aus TUS100710 Technical Description SMA America LLC Unpacking the Sunny Central 5 5 Lifting the Sunny Central off the transport crate floor A WARNING Danger of crushing Danger of damage of the Sunny Central Sunny Central may tip over if improperly transported e Transport the Sunny Central as described in the Sunny Central installation guide Technical Description SC500HE US_Aus TUS100710 19 Unpacking the components SMA America LLC 6 Unpacking the components The components of the Sunny Central are stowed in the Power Cabinet and in the Control and Interface Cabinet This chapter describes where the components are located and what must be taken into account when2. Any equipment used for the transport must be suitable for weight of the crate Do not tilt the crate during transport 4 1 Transporting the crate with a crane or a forklift The position for transport with a transport crane is marked on the transport crate see chapter 3 2 Symbols on the transport crate page 13 For transport you can use a crane fork or a burden chain 1 Push the crane fork the burden chain or the forklift at the marked positions under the transport crate Secure the crate against tilting Transport the crate 14 SC500HE US_Aus TUS100710 Technical Description SMA America LLC Transport the transport crate 4 2 Transporting the crate by pulling NOTICE The Sunny Central can be damaged by shock when pulling the crate over uneven ground Damage to the Sunny Central will result Do not pull the crate over uneven ground e Pull the crate along slowly For transporting the crate there are eyelets underneath the right and left panels 1 Secure the transport hooks on the eyelets 2 Harness the equipment used for transport 3 Transport the crate Technical Description SC500HE US_Aus TUS100710 15 Unpacking the Sunny Central SMA America LLC 5 Unpacking the Sunny Central The crate is closed using TX screws On the right side panel of the crate there is a flap behind which is kept a TX bit 5 1 Preparing the tools 5 2 Removing the transport crate The
3. Unpacking SUNNY CENTRAL 500HE US Technical Description SCSOOHE US_AusTUS100710 98 4025910 Version 1 0 Cus SMA America LLC Legal Restrictions Copyright O 2010 SMA America LLC All rights reserved No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photographic magnetic or otherwise without the prior written permission of SMA America LLC SMA America LLC makes no representations express or implied with respect to this documentation or any of the equipment and or software it may describe including with no limitation any implied warranties of utility merchantability or fitness for any particular purpose All such warranties are expressly disclaimed Neither SMA America LLC nor its distributors or dealers shall be liable for any indirect incidental or consequential damages under any circumstances The exclusion of implied warranties may not apply in all cases under some statutes and thus the above exclusion may not apply Specifications are subject to change without notice Every attempt has been made to make this document complete accurate and up to date Readers are cautioned however that SMA America LLC reserves the right to make changes without notice and shall not be responsible for any damages including indirect incidental or consequential damages caused by reliance on the material presented including but n
4. center of gravity A The center of gravity of the crate is not located in the middle of the crate The symbol for the center of gravity A marks the position of the center of gravity of the crate SC500HE US_Aus TUS100710 Technical Description SMA America LLC The transport crate 3 2 Symbols on the transport crate There are following symbols on the transport crate Symbol Explanation t The crate must be transported with this side to the top The contents of the crate are fragile 11 Do not use sharp tools to open the crate Do not place anything on the crate x Center of gravity of the crate Position for transport with a crane 3 3 Technical Data of the Transport Crate Weight 5025 lbs 2280 kg Width x Height x Depth 9 ft 6 3 6 in x 3 ft 9 3 in x 8 ft 5 in 2900 mm x 1150 mm x 2580 mm Technical Description SC500HE US_Aus TUS100710 13 Transport the transport crate SMA America LLC 4 Transport the transport crate You can transport the crate in 3 different ways e Transport with a crane e Transport with a forklift e Transport by pulling The following chapters describe what to take into account during transport A WARNING The crate will tilt if transported wrongly Serious injuries during transport of the Sunny Central will result Transport the crate as described in this manual Note the center of gravity label on the crate
5. covers on the sides of the unit For all repair and maintenance always return the unit to an authorized SMA Service Center Before installing or using the Sunny Central 500HE US read all of the instructions cautions and warnings on the Sunny Central 500HE US in this technical description Before connecting the Sunny Central 500HE US to the power distribution grid contact the local power distribution grid company This connection must be made only by qualified personnel Wiring of the Sunny Central 500HE US must be made by qualified personnel only 6 SC500HE US_Aus TUS100710 Technical Description SMA America LLC Table of Contents Table of Contents 1 1 1 1 2 1 3 2 2 1 2 2 2 2 1 2 2 2 2 3 3 1 3 2 3 3 4 1 4 2 5 1 5 2 5 3 5 4 5 5 Notes on this manual o ooooooooooooooo 9 Areg of validity o seese een 9 Target GrOUD 3 2 Nr AA 9 INMI bee di 9 Delivery of the Sunny Central 10 Checking for transport damage na iaa 10 Packingilis bs aie na sare ea ehren 10 Na OEL e T E abs 10 Components included in delivery 0 0 000 e eee eee eae 11 Storage sa uss EN ER 11 The transport erate u en aa ween 12 Parts of the transport crate and center of gravity 12 Symbols on the transport crate 2 2 2 ee eee ee eee eee 13 Technical Data of the Transport Crate 2222 22222222 13 Transport the transport crate ooooooooo o 14 Transpor
6. result in damage to or destruction of part or all of the SMA equipment and or other equipment connected to the SMA equipment or personal injury DANGER DANGER indicates a hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE NOTICE is used to address practices not related to personal injury 4 SC500HE US_Aus TUS100710 Technical Description SMA America LLC Important Safety Instructions Other symbols in this document In addition to the safety and hazard symbols described on the previous pages the following symbol is also used in this technical description Information e l This symbol accompanies notes that call attention to supplementary information that you must know and use to ensure optimal operation of the system Technical Description SC500HE US_Aus TUS100710 5 General Warnings SMA America LLC General warnings A General warnings All electrical installations must be done in accordance with the local codes and National Electrical Code ANSI NFPA 70 The Sunny Central 500HE US contains no user serviceable parts except for the fans on the bottom of the enclosure and the filters behind the fans as well as the handle
7. screw points on the transport crate are marked in red HSV MNOWRYDND HR o pp Move the flap to the left Pull out the pouch with the drill bit from the flap Remove the drill bit from the pouch Place the drill bit in the drill The tool is prepared Remove the TX screws from the roof Remove the roof Remove the TX screws from the back panel Remove the back panel Remove the TX screws from the front panel Remove the front panel Remove the TX screws from the right panel Remove the right panel Remove the TX screws from the left panel Remove the left panel The transport crate has been removed SC500HE US_Aus TUS100710 Technical Description SMA America LLC Unpacking the Sunny Central 5 3 Removing the foil from the Sunny Central The Sunny Central is packed in an airtight foil NOTICE Open the foil with a sharp object Damage to the Sunny Central coating or to the display will result Do not cut deeply into the foil 1 Open the foil carefully with a knife or scissors 2 Remove the foil from the Sunny Central M The foil has been removed from the Sunny Central Technical Description SC500HE US_Aus TUS100710 17 Unpacking the Sunny Central SMA America LLC 5 4 Removing the straps from the Sunny Central The Sunny Central is fixed with straps to the floor of the transport crate
8. and the components delivered 2 2 1 Accessories kit The accessories kit is packed in a box The description of the box is SC SOOHE US BEIP1 SC 500HE US BP1 Number Description 1 Hexagonal wrench 4 mm Non woven abrasive Sunny Central 500HE US installation guide Sunny Central 500HE US user manual Sunny Central 500HE US wiring diagram n Sunny Central 500HE US commissioning report Packaging material 10 SC500HE US_Aus TUS100710 Technical Description SMA America LLC Delivery of the Sunny Central 2 2 2 Components included in delivery Number Description 1 Back plinth panel Power Cabinet Front plinth panel Power Cabinet Side panel Power Cabinet Back plinth panel Control Interface Cabinet Front plinth panel Control Interface Cabinet Air baffle with middle wall Accessories kit carton ll Display cover 2 3 Storage Do not store the Sunny Central in the crate for a period longer than 6 months After months the Sunny Central is no longer protected against moisture penetration Technical Description SC500HE US_Aus TUS100710 11 The transport crate SMA America LLC 3 The transport crate 3 1 Parts of the transport crate and center of gravity The transport crate is made up of 6 parts Front panel Back panel Left panel Right panel Base Roof You can identify the front back wall by the symbol for the
9. d 3 Cut the cable ties attaching the accessories kit in the Sunny Central by a knife and remove them 4 Remove the accessories kit from the lower part of the Control and Interface Cabinet 5 Attach the plinth panel to the Control and Interface Cabinet 6 Unpack the accessories kit 24 SC500HE US_Aus TUS 100710 Technical Description SMA America LLC Unpacking the components 6 5 1 Assembling the air baffle Loosen and unpack the filter plate from the side of the Sunny Central Remove the middle wall of the air baffle and plinth panels from the Interface Cabinet Remove the screws from the filter plate Put the middle wall on the filter plate Attach the middle wall to the filter plate using the screws provided Hor wn a The air baffle is assembled Installing the air baffle o I The Sunny Central installation guide describes how to install the air baffle 6 6 Removing the display packaging NOTICE During mounting and installation of the Sunny Central objects can scratch the surface of the display Damage to the display will result Remove the display packaging only after all mounting and installation work on the Sunny Central is completed Remove the adhesive strips Pull off the lid toward the front CoN o Remove the protective foil from the display M The display packaging has been removed 6 7 Further installation steps All further installation wo
10. ective film above the system control board before commissioning the Sunny Central 1 Open the doors of the Control and Interface Cabinet NOTICE Electrostatic discharge when touching the components Damage to the components will result Ground yourself by touching a grounded surface before touching the components Remove the adhesive strips at the protective film Remove the foil completely Check the Control and Interface Cabinet for packaging remains and remove them 5 Close the doors of the Control and Interface Cabinet 6 5 Unpacking the plinth plate for Control Cabinet and air baffle The air baffle is made up of two parts a filter plate and a middle wall The air baffle has been removed for the transport The filter plate is attached to the side on the outside of the enclosure of the Sunny Central The middle wall of the air baffle and the plinth panels are in the lower part of the Interface Cabinet Technical Description SC500HE US_Aus TUS 100710 23 Unpacking the components SMA America LLC Position Name A Accessories kit B Plinth panels for Control Cabinet middle wall of the air baffle Filter plate 1 Loosen the 7 screws at the right side of the plinth panel of the Control and Interface Cabinet by turning them counterclockwise 2 Pull the right plinth panel of the Control and Interface Cabinet forwar
11. onal protective equipment Keep a safe distance from the straps 1 Hold the filter plate so that it cannot fall over 2 Cut through the straps with a knife and remove them 3 Put the filter plates aside Technical Description SC500HE US_Aus TUS100710 21 Unpacking the components SMA America LLC 6 3 Removing the power unit packaging The power units are located in the Power Cabinet You have to unpack the power units before commissioning of the Sunny Central Li Unlock the door of the Power Cabinet 2 Pull the handle of the Power Cabinet upwards and turn it to the right 3 Open the right door of the Power Cabinet 4 Inside of the left door is a handle Turn the handle by 180 to the top left M The door is released 5 Open the left door of the Power Cabinet NOTICE Touching the components can result in electrostatic discharges Damage to the components will result Ground yourself by touching a grounded surface before touching the components 6 Remove the adhesive strips Remove the foil completely 8 Check the Power Cabinet for packaging rests and remove them M The power unit packaging has been removed 22 SCSOOHE US_Aus TUS100710 Technical Description SMA America LLC Unpacking the components 6 4 Removing the protective film of the system control board The system control board of the Sunny Central can be found in the Control and Interface Cabinet You have to remove the prot
12. ot limited to omissions typographical errors arithmetical errors or listing errors in the content material All trademarks are recognized even if these are not marked separately Missing designations do not mean that a product or brand is not a registered trademark The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by SMA America LLC is under license SMA America LLC 3801 N Havana Street Denver CO 80239 U S A Technical Description SC500HE US_Aus TUS100710 3 Important Safety Instructions SMA America LLC IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for Sunny Central 500HE US PV inverter that must be followed during installation and maintenance of the PV inverter The Sunny Central 500HE US is designed and tested according to international safety requirements but as with all electrical and electronic equipment certain precautions must be observed when installing and or operating the Sunny Central 500HE US To reduce the risk of personal injury and to ensure the safe installation and operation of the Sunny Central 500HE US you must carefully read and follow all instructions cautions and warnings in this technical description Warnings in this document A warning describes a hazard to equipment or personnel It calls attention to a procedure or practice which if not correctly performed or adhered to could
13. ral SOOHE US 1 2 Target group This manual is for qualified personnel only Qualified personnel have received training and have demonstrated skills and knowledge in the construction and operation of the device Qualified personnel are trained to deal with the dangers and hazards involved in installing electric devices 1 3 Syntax In this document the Sunny Central 500HE US is referred to in the following as Sunny Central In this document SMA America Production LLC is referred to in the following as SMA Technical Description SC500HE US_Aus TUS100710 9 Delivery of the Sunny Central SMA America LLC 2 Delivery of the Sunny Central 2 1 Checking for transport damage In order to determine any damage that may have occured during transport two impact indicators are affixed to the transport crate of the Sunny Central The indicators show whether the Sunny Central was subjected to an impact during transport which may have damaged it Upon delivery check the impact indicators How the impact indicator shows an improper transport of the transport crate is either described on the impact indicator itself or in a manual on the impact indicator included in the delivery 2 2 Packing list The Sunny Central is delivered in a wooden crate The crate contains both cabinets of the Sunny Central The accessories kit is in the cabinets as are the components which were dismounted for transport This chapter lists the content of the accessories kit
14. rk is described in the installation guide of the Sunny Central The installation guide is included in the delivery of the Sunny Central Technical Description SC500HE US_Aus TUS100710 25 Contact 7 Contact SMA America LLC If you have technical problems with our products contact the SMA Serviceline We require the following information in order to provide you with the necessary assistance e Inverter type of the Sunny Central Serial number of the Sunny Central SMA Solar Technology America LLC 4031 Alvis Court Rocklin CA 95677 Tel 1 916 625 0870 Tel 1 877 MY SMA TECH Tel 1 877 697 6283 Toll free available for USA Canada and Puerto Rico Fax 1 916 625 0871 Service QSMA America com www SMA America com 26 SC500HE US_Aus TUS100710 Technical Description SMA America LLC
15. ting the crate with a crane or a forklift 14 Transporting the crate by pulling o0o o 15 Unpacking the Sunny Central 16 Preparing the tools AA A gute see ae 16 Removing the transport crate 0 eee eee eee 16 Removing the foil from the Sunny Central 17 Removing the straps from the Sunny Central 18 Lifting the Sunny Central off the transport crate floor 19 Technical Description SC500HE US_Aus TUS100710 7 Table of Contents SMA America LLC 6 1 6 2 6 3 6 4 6 5 6 5 1 6 6 6 7 Unpacking the components oooooooooooo o 20 Position of the keys and of the hexagonal wrench 20 Removing the filter plate from the outer wall of the Sunny Central ee 21 Removing the power unit packaging 222222220 0 22 Removing the protective film of the system control board 23 Unpacking the plinth plate for Control Cabinet and air baffle 23 Assembling the air baffle 0 6 0 cece eee eens 25 Removing the display packaging 00000e 25 Further mstallationstepscacac san 25 Contact 23 nen sr ere 26 SC500HE US_Aus TUS100710 Technical Description SMA America LLC Notes on this manual 1 Notes on this manual This manual describes the unpacking of the Sunny Central 500HE US Keep this manual in a convenient place for future reference 1 1 Area of validity This manual is valid for the Sunny Cent
16. unpacking the components Parts of the Sunny Central Position Name A Power Cabinet B Control and Interface Cabinet Cc Display D Front plinth panel Control and Interface Cabinet E Front plinth panel Power Cabinet 6 1 Position of the keys and of the hexagonal wrench The keys and the hexagonal wrench are in a bag affixed to the Control and Interface Cabinet door The bag contains 2 keys for the Stop Start switch below the display 2 keys for the Sunny Central doors e 1 hexagonal wrench 20 SC500HE US_Aus TUS100710 Technical Description SMA America LLC Unpacking the components Removing the keys 1 Remove the bag with the keys from the Sunny Central 2 Keep the keys in a safe place You need the keys to open the Sunny Central doors and to start or stop the Sunny Central You need the hexagon allen key for loosening and attaching the enclosure s screw fitting 6 2 Removing the filter plate from the outer wall of the Sunny Central The filter plate A is attached with straps to the side of the Sunny Central You have to remove the straps to open the Sunny Central NOTICE The straps are under tension and spring back when removed Injury due to straps springing back will result e Wear pers
Download Pdf Manuals
Related Search