Composite Thrusters
Contents
1. Composite Thrusters Max Power Quick User Manual Manuel d utilisateur Max Power Max Power Benutzerhandbuch Max Power Manual del usuario Max Power Guida rapida Serial Number Num ro de S rie Serien Nummer N de serie Thruster Model Mod le du Propulseur Ruder Modell Modelo de h lice Numero di serie Elica di manovra modello 10 All e F Coli 06210 Mandelieu France Tel 33 4 92 19 60 60 Fax 33 4 92 19 60 61 mp max power com www max power com General Safety Guidelines a b c d e f g Care must be taken not to use the thruster in swimming areas or at any time when people maybe in the water close to the thruster Never tamper with thruster or thruster turbine if not 100 sure that all thruster electrical circuits have been cut off Under no circumstances should the thruster or its motor be run with the boat out of the water When taking possession of a boat equipped with a Max Power thruster you must familiarise yourself with the thruster system as installed on your boat Make sure that you know where the following components are located on your boat l The thruster unit li The battery bank used for your thruster lil The power fuse as installed in the main positive battery supply cable of the thruster iv The manual battery isolator switch as installed in the main positive battery supply cable of the thruster v The isolator switch on the DC equipment panel of your b2. R When switched ON the unit will beep once and the green LED in the red push button will light up When switched OFF the unit will beep twice and the green LED in the red push button will go out If the thruster motor overheats the unit will start beeping while the green LED will flash until the thruster motor has cooled down Once the overheat alarm starts the user has 10 seconds of actual thruster use before the unit automatically shuts down The unit will then not be able to be switched on again until the motor has cooled down If the thruster unit has not been used for a period of ten minutes the unit will automatically switch off Before switching off automatically the unit will warn you by beeping once followed by a second beep a few seconds later after which the unit switches off Basic Operation With the switch or isolator on DC equipment panel and the manual battery isolator switched on a b c d switch on control panel as described previously in manual Push red button or incline joystick to the left boat moves to the left Push green button or incline joystick to the right boat moves to the right When manoeuvring take into consideration the inertia effects remember the boats momentum continues after you release the joystick button therefore remember to release the control prior to reaching your desired position Keep in mind when starting your manoeuvre that your thruster can not be run c
3. oat for the thruster Always switch off both the isolator on the DC equipment panel for control supply amp the thruster manual battery isolator thrusters power supply after having left port amp when the manoeuvre is finished after docking The thruster unit should be kept dry and ventilated at all times Failing to respect this will result in pre mature failure of the unit as well as creating a risk of an electrical fault condition or short circuit Under no circumstances should any inflammable products be stored next to the electric components of the thruster installation Control Panel amp Control System Functions To switch the thruster ON or OFF follow the instructions on the diagram below VASE Single Touch Panel POWER for one second Red Push button To Switch ON or OFF push with Green LED n a down both red amp green push button Green Push button a o Single Joystick Panel M To Switch ON or OFF push ns lt m gt i down the red push button while Rist Puati button w pushing joystick to the right for with Green LED il one second THRUSTER Red Push button with Green LED a b c d e Double Joystick Panel To Switch ON or OFF push down the red push button while pushing joystick to the right for one second for both bow and stern thruster Joystick Joystick C l Rep Red Push button Sa with Green LED an n STERN THRUSTE
4. ontinuously for more than 1 5 minutes Overheat Alarm The electric motor of the thruster is fitted with an over heat sensor If the thruster motor overheats the buzzer in the control panel will start beeping while the green LED In the red push button will flash Once the overheat alarm starts the user has 10 seconds off actual thruster use before the unit automatically shuts down The unit will then not be able to be switched on again until the motor has sufficiently cooled down Information or assistance please refer to the Installation Operation amp Maintenance manual for your specific thruster model which are available on our web site www max power com J or contact your closest Max Power distributor See Distributor Contact List for further assistance Warranty The purpose of this document is to set out the terms of warranty cover offered in relation to products purchased by the End User from Max Power or its approved network of resellers This document will adhere to the following format 1 Definitions Authorized Repair Number The number given by Max Power on reporting a fault with your thruster Dealer An authorized Max Power sales centre End User The boat supplied with supplied equipment and the owner thereof Installer The authorized centre responsible for the installation of your thruster Manufacturer supplier of the equipment under warranty Pleasure Craft Vessels used for owner s personal u
5. se that have no commercial use i e Charter boats or work boats Resellers Max Power approved distributors and dealers Serial Number Number in upper right hand corner of Warranty document Supplier The manufacturer Max Power Warranty The terms and conditions that are covered by the manufacturer 2 Period of Coverage The equipment manufactured by the Supplier is guaranteed to be free from defective workmanship components and materials under normal usage conditions for a period of two years from the date of purchase by the End User This warranty Is transferable to subsequent owners of this equipment during the period of coverage If the material is used for anything other than for pleasure craft the guarantee Is limited to a six month period 3 Warranty Registration Register your purchase now to receive free extended warranty coverage This can be done using one of the following methods NB proof of purchase must be included to establish that equipment is still under warranty a The quickest and easiest method to register your warranty is to fax the attached installation check list and warranty registration to the Manufacturer Fax 33 4 92 19 60 61 b Mail in your warranty registration document please ensure that you make a copy before sending it 10 All e F Coli 06210 Cannes Mandelieu France 4 Warranty Terms Year 1 All factory testing diagnosis repairs and replacements are performed at no charge to the End U
6. ser All parts and up to two hours of labour are covered for repairs and replacements conducted in the field Year 2 All factory testing diagnosis repairs and replacements are performed at no charge to the End User This excludes any damage or faults occurring from normal wear and tear on the following items engine oil seals relay contacts If warranty is registered within the 3 month period following installation also excluded labour amp shipping costs 5 Warranty Exclusions Damage due to modifications or installation contrary to published specifications Cost of hauling the boat Damage due to repairs performed by an unauthorized service centre Damage due to lack of normal maintenance services Damage due to water Parts replaced due to normal wear and tear Repairs performed without knowledge of manufacturer please contact dealer to receive Repair Authorization Number Tampering of equipment by the End User Cost of travel to and from the job site Cost of economic loss including injury to any person damage to property loss of income or profit Communication lodging inconvenience Consequential damage due to failure including those arising from collision with other vessels or objects 6 Procedural Guidelines PLEASE VIEW THE TROUBLE SHOOTING LIST TO ASCERTAIN OR SOLVE ORIGIN OF PROBLEM PRIOR TO CONTACTING THE DEALER INSTALLER 1 Contact your dealer installer to report the problem a If you do not know who this is contac
7. t the nearest Max Power distributor b If you are in foreign waters please contact the nearest Max Power distributor 2 Ensure you have your serial number and model number to hand top right hand corner of warranty 3 Dealer Installer will come to site to decipher the cause of the fault 4 Ifthe cause of fault is due to a manufacturing problem the dealer will contact Max Power to receive Repair Authorization Number 9 If the problem is due to an installation error please contact your installer
Download Pdf Manuals
Related Search