APAX-5570 Hardware Manual Ed1
Contents
1. N E 1 5 0 9 ae il ce B a O l a Sa 03 ar a e E co 3 eo En San J an is gt T oS Lu i CCC E l 2 gt I 1 132 00 113 90 2 ee 125 30 _ Of Scl 06 EIl T4484 LULU UN APAX 5570 User Manual 16 2 2 2 2 1 Power Supply Module APAX 5343 Input Rated Voltage 115 230 VAC E Voltage Range 902. 35 APAX 5570 User Manual Below are the procedures for the wall panel mounting 1 Hang the APAX 557X onto the screw on the wall panel The screws for APAX 557X need to be special designed We have provided it in the accessory 2 Mount APAX 557X to the wall panel using two screws APAX 5570 User Manual 36 3 Ifyou want to have stronger mounting effect pull down the DIN rail locks and screw the three DIN rail locks with three screws 4 If needed stack APAX 5002 backplane to APAX 557X Lock the APAX 557X backplane to APAX 557X by the backplane locks Mount that APAX 5002 back plane to the wall panel using two screws 37 APAX 5570 User Manual 5 Repeat Step 4 until all necessary APAX 5002 backplane are screwed on the wall panel When the total number of APAX 5520 and APAX 5000 1 0 modules is TES odd you can use APAX 5001 1 slot backplane as the last backplane in the system The procedure to screw APAX 5001 on
3. User Manual APAX 5570 5571 PC based Controller with Celeron M CPU AD ANTECH eAutomation Copyright The documentation and the software included with this product are copyrighted 2009 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Product Warranty 2 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liabilit
4. 264 VAC Input Current 1 5 A at rated load Input Frequency Range 47 63 Hz Inrush Current 50 A one cycle at 25 C Output Output Power 72 watt Rated Voltage 24 VDC Rated Output Current 3A Efficiency gt 87 at 115 230 VAC Input Voltage Rated load Protection Isolation Protection In Out 42 42 VDC Over Voltage Protection 26 29 VDC Latch off mode Over Load Protection auto recovery mode Short Circuit Protection auto recovery mode General Diagnostic LEDs 1 x Power E Dimensions W x H x D 75x 151 x 115 mm Operating Temperature 0 55 C Storage Temperature 20 75 C Relative Humidity 5 95 non condensing 17 APAX 5570 User Manual APAX 5570 User Manual 18 Installation and Initiation 3 1 Assembly and Power Connections 3 1 1 Combining APAX 5000 I O Modules with APAX 557X 1 There are two blank modules inserted on APAX 557X in default Pull up the module locks on the two blank modules 2 Detach the two blank modules from APAX 557X 3 Insert APAX 5000 I O module on the first slot on APAX 557X Use tongue and groove slots to move the module APAX 5570 User Manual 20 4 Lock the APAX 5000 I O modules to the APAX 557X by pulling down the mod ule locks 5 If needed insert another APAX 5000 I O module on the second slot on APAX 557X Use tongue and groove slots to move the module 6 Lock the second APAX 5000 I O module to AP
5. Description of your peripheral attachments Description of your software OS version application software etc A complete description of the problem The exact wording of any error messages Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage wm To avoid electrical shock always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC is on Disconnect power before making any configuration changes The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components jii APAX 5570 User Manual Safety Instructions 10 11 12 13 19 16 17 18 19 20 21 22 23 Read these safety instructions carefully Keep this User Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning For plug in equipment the power outlet socket must be located near the equip ment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is
6. Ethernet network Programmers can leverage the communication ability through Modbus RTU master slave and Modbus TCP server client APAX 557X provides one DVI I interface and Four USB ports Through these APAX 557X can be connected to Advantech Industrial Monitor FPM or standard monitor with DVI or VGA input Touch functionality is connected via USB Audio interface enables APAX 5570 to connect with other audio device such as microphone 1 2 System Architecture There are two slots on APAX 557X that you can insert various APAX 5000 I O mod ules making it a complete control system When connected with other APAX 5001 or APAX 5002 backplane modules even more APAX 5000 I O modules can be inte grated into the system to handle more complicated applications refer to section 3 1 1 for how to assemble APAX 5000 1 0 modules APAX 557X is powered by a standard power supply with 18 30 VDC voltage input through the power connector Users can also leverage the APAX 5343 power supply module provided by Advantech which features the same form factor as APAX 557X APAX 5343 can be stacked on the left side of APAX 557X Since APAX 557X supports dual power input two APAX 5343 s can be connected to one APAX 557X Refer to Section 3 1 2 for how to con nect APAX 5343 with APAX 557X Note With expansion port on backplanes users can build a remote expansion ru architecture remaining fast local bus data transmission speed Refer to E Section 3 1 1 for h
7. has individual MAC address and you can configure different IP address for the two Ethernet ports Therefore APAX 557X can link to two different Ethernet network Left LED Speed Or OMe Green 100 Mbps Orange 1000 Mbps Right LED Link Activity OFF Noik Orange lActviy 5 APAX 5570 User Manual LAN MDI 0 LAN MDI 0 LAN MDI 1 Tanz e pame e pamon e pwm Note The Ethernet port is only used in LAN not for connection to telecommu g nication circuits 1 3 4 USB Ports The USB connector is used for connecting any device that conforms to the USB inter face Many recent digital devices conform to this standard The USB interface sup ports Plug and Play which enables you to connect or disconnect a device whenever you want without turning off the computer The APAX 557X provides four connectors of USB interfaces The USB interface complies with USB EHCI Rev 2 0 compliant The USB interface can be disabled in system BIOS setup Refer to figure below for its pin assignments A N i VBUS Power 5V CE Data CE DC an APAX 5570 User Manual 6 1 3 5 1 3 6 VGA Display APAX 557X provides DVI I interface which transfer analog and digital data and is suitable for connection to analog graphics cards with 15 pin D sub connector and dig ital graphics card with DVI D output You could directly link your DVI monitor Besides the DVI interface uses VGA signal so the connec
8. AX 557X by pulling down the module locks 21 APAX 5570 User Manual If you need more than two APAX 5000 I O modules stack one APAX 5002 1 backplane to the right side of APAX 557X Warning When you assembly different backplanes with APAX 557x together remember to turn off the power connected to APAX 557x If not the backplanes may be damaged Turn on the power again after you com plete the assembly for all backplanes 8 Lock the stacked APAX 5002 backplane to APAX 557X by the backplane locks Insert the third APAX 5000 I O module to the stacked APAX 5002 backplane Use tongue and groove slots to move the module 22 APAX 5570 User Manual 10 Lock the third APAX 5000 module to the stacked APAX 5002 backplane 11 If needed insert the fourth APAX 5000 I O module to the stacked APAX 5002 backplane Use tongue and groove slots to move the module 12 Lock the fourth APAX 5000 I O module to APAX 5002 backplane If you need more APAX 5000 I O module repeat Step 7 Step 12 until all necessary APAX 5000 I O modules are inserted on the backplanes When the total number of APAX 5000 I O modules is odd you can use 1 slot APAX 5001 backplane module 5 the last backplane in the system 23 APAX 5570 User Manual APAX 5570 User Manual 24 There is an expansion port on front side of APAX 5002 With this port users can build a remote expansion architecture remaining fast local bus data transmission s
9. IN rail 32 3 3 2 Wall Panel Mounting sss 35 Error Handling and Diagnostics 41 Error Handling and Diagnostics nenne 42 V APAX 5570 User Manual APAX 5570 User Manual yi Chapter 1 Overview 1 1 Introduction APAX 557X is a high performance controller CPU module with Intel Celeron M grade CPU and Windows XP Embedded operating system The operating system is installed in the internal CF card Therefore no extra external HD is required for the operating system and application programs Besides APAX 557X provides an exter nal SD slot for data storage data logging By connecting with different APAX 5000 I O modules APAX 557X can execute con trol tasks for various industrial control and automation applications Through built in utility programmers can configure related hardware settings for the APAX 5000 I O modules Then programmers can build their own application programs under Microsoft Visual Studio NET or C C programming environment Note Please refer to APAX 557X software manual for how to configure the E 1 hardware and program under Microsoft Visual Studio NET or C C APAX 557X offers two serial ports 1 x RS 232 port and 1 x RS 422 485 port and two Ethernet ports to communicate with other devices The two Ethernet ports are served as two different MAC address enabling APAX 557X to connect with two dif ferent
10. No XXXXXXXXXX Edition 1 Printed in Taiwan June 2009 APAX 5570 User Manual ii Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech Please contact your local supplier for ordering information FCC Class A Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Technical Support and Assistance 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number
11. PAX 557X delivers one relay output to display if the two power inputs are both available through the RL and RL pin You can connect an alarm indicator buzzer or other signaling equipment through the relay output Refer to table below for how it changes its status Power Connector Serial Vit WI W2 V2 RL RL GND Txt Tx Rx Rx IGND APAX 5570 User Manual 10 Be Poe input LS CE LT CE LT CS ON Close Except connecting to standard DC power input Advantech also provides power sup ply module APAX 5343 It is the same that dual power inputs are supported so you can combined two APAX 5343 modules to one APAX 557X Refer to Section 2 2 1 for its specification and Section 3 1 2 for how to assembly it with APAX 557X 11 APAX 5570 User Manual APAX 5570 User Manual 12 Chapter 2 Product Specifications 2 1 2 1 1 CPU Modules APAX 5570XPE CPU Intel Celeron M 1 GHz Memory 512 MB DDR2 DRAM onboard Dual Channel Mode Battery Backup Memory 512 KB Operating System Windows XP Embedded Diagnostic LEDs 1 x Power 1 x Run controlled by software 1 x Battery 1 x Error controlled by software 2 x LAN link activity speed Real time Clock Yes battery backed Watchdog Timer Yes Reset Button Yes Control Software NET class library and C C API Power Consumption 30 W 24 VDC typical without module inserted VGA 1 DVI I interface Audio Interface MIC input Line Ou
12. ach APAX 557X module one APAX 5002 backplane is stacked backward for expansion The APAX 5000 I O modules are inserted on the backplanes Unmanaged industrial Ethernet switches such as EKI 2528 with 100 Mbps transmission speed and standard Ethernet cable connect the two APAX 557X modules and APAX 5000 I O modules APAX 5000 series will automatically decide which one is the master controller Be aware that two APAX 557X modules MUST be configured with different controller ID numbers Ethernet Switch VIDS Warning 1 It is suggested to power on all the I O modules and the two APAX 557X controllers together to avoid any unpredictable situation A 2 DO NOT use managed switch hub or router between backplanes for expansion 3 The network for the expansion should be a local network NOT an external network such as public network including Internet 4 Shielded industrial Ethernet cable MUST be used instead of standard Ethernet cable when the system is used in harsh environment such as factory automation Cat 6 Ethernet cable is strongly recommended for better data transmission quality Note The maximum length for the Ethernet cable between two backplanes is 100 m IH 3 APAX 5570 User Manual 1 3 Hardware Functionality 1 3 1 RS 232 Interface COM 1 The APAX 557X offers one standard RS 232 serial communication interface port COM 1 9 pin Sub D plug connector and it is located on the front panel of APAX 557X Ref
13. an 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein APAX 5570 User Manual iv Chapter Chapter Chapter Chapter 1 i i i N 2 2 1 2 2 3 3 1 3 2 3 3 4 4 1 OverVi eW asas 1 MOC UC OEE a See 2 System Architec Ure nennen ka ne SE Aaa ER 2 Hardware Functionality sass 4 1 3 1 RS 232 Interface COM 1 4 1 3 2 RS 422 485 Interface COM 2 4 193 EVIE FON ee aes x EE K EA ek 5 Taa USB PONS Sa O aa ae an 6 DA ee E ae 7 1 3 6 Battery Backup RAM and SD Card 7 13 7 15895861 8 1101 cece aise mn ee ne en a an un 9 TG PUNO E E E 9 1 3 9 Real Time Clock RTC 10 1 19 Fan CAR ee ee 10 18 11 Power Gonneel r unse 10 Product Specifications 13 COS ee nee ee see 14 eee ee eee 14 2 1 2 APEX PRE ee 15 2 1 3 APAX 557X Dimensions 16 Power Supply Module ss 17 22l APA SG eee eee 17 Installation and initiation 19 Assembly and Power Connections 20 3 1 1 Combining APAX 5000 I O Modules with APAX 557X 20 3 1 2 Combine with APAX 5343 Power Supply Module 27 Decommission and Disposal nennen 32 IVO UELI ee en E nee 32 3 3 1 D
14. ckup mem Ory APAX 557X has built in Microsoft Windows XP Embedded operating system The operating system is installed in the internal CF card Your application program will also be stored on the internal CF card Besides APAX 557X provides one external SD card slot for data storage and you can use standard SD card to store your data The maximum size for the SD card is 16 GB Refer to figure below for the location of SD card slot Battery Note There are four disk devices provided by APAX 557x Internal CF C D T External SD slot E and Battery Backup RAM Disk Z Refer to the fig ure below The operating system Windows XP Embedded and pro gram applications are installed on the internal CF Considering data storage for your applications we strongly suggest NOT to use the inter nal CF Repeat writing CF will decrease the life for CF card You can store your data in the battery backup RAM or SD card APAX 5570 User Manual 8 1 3 7 1 3 8 My Computer ol x File Edit View Favorites Tools Help ae gt Search Wey Folders gt F x if Address P My Computer Go Files Stored on This Computer mm Shared Documents C3 Administrator s Documents Hard Disk Drives RZ ge APAX 5570 C op New Volume D Le Devices with Remorable Storage lt Removable Disk Ei 1 objects selected My Computer Battery Specifications M Battery Type CR2032 wm Electr
15. correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or electrical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment does not work well or you cannot get it to work according to the user s manual The equipment has been dropped and damaged The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAMAGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s position according to IEC 704 1 1982 is no more th
16. er to figure below for RS 232 port pin assignment 12345 OOOOO OOOO 6 7 8 9 Assignment Description DCD Data Carrier Detect Receive Data TxD Transmit Data u o Data Terminal Ready NO Gm Request to Send Clear to Send 1 3 2 RS 422 485 Interface COM 2 APAX 557X delivers one isolated RS 422 485 serial communication interface port COM 2 to connect with other devices RS 422 485 interface uses the same connec tor as power input APAX 5570 User Manual 4 1 3 3 Serial Power Connector RS 422 gt _ nn RS 485 I Vite Vi V2 V2 RL RL GND Txt Tx Rx IGND pin Asstnment eset Zn Data Receive RS 485 Pin assignment Description Tf e oo mooo Data In RS 485 mode it supports auto data flow control functionality it automatically detects the direction of incoming data and switches its transmission direction accord ingly So no handshaking signal e g RTS signal is necessary This lets you conve niently build an RS 485 network with just two wires More importantly application software previously written for half duplex RS 232 environments can be maintained without modification Ethernet Ports The APAX 557X is equipped with two Ethernet ports which are fully compliant with IEEE 802 3u 10 100 1000 Mbps Ethernet The two Ethernet ports provide a standard RJ 45 jack on board and LED indicators on the front side to show its status Refer to Table below Each Ethernet port
17. ical Properties Nominal voltage 3 0 V Nominal capacity 210 mAh Load 15 k End voltage 2 0 V m Dimensions Diameter 21 0 mm Height 5 5 mm Weight 3 0 g Warning Battery may explode if mistreated Do not recharge disassemble or dis pose of in fire Reset Button APAX 557X features a reset button on the front panel Operators can manually reboot the system with the reset button Audio APAX 557X offers the audio interface MIC input and Line Out output are available The audio interfaces are accessed via the operating system 9 APAX 5570 User Manual 1 3 9 Real Time Clock RTC APAX 557X delivers built in real time clock and programmers can use it in their application programs When the power is loss the RTC can still run using the power from battery which has been described in section 1 3 6 1 3 10 Fan Cartridge APAX 557X with higher performance CPU needs fan for heat dissipation such as APAX 5571XPE The fan is fixed on the side of the heat sink with screws A cover is provided to prevent items enter and damage the fan when the fan is running The fan is powered by APAX 557X without any external power device 1 3 11 Power Connector APAX 557X needs external DC power supply though the connector on the left side APAX 557X supports dual 18 48 VDC power input and power fail relay output Two DC power inputs can be connected to the system through the four pins V1 V1 V2 and V2 A
18. ionality Therefore you can detach the APAX 5000 I O modules when the system is powered on No matter they are inserted on the APAX 5570 or APAX 500x backplane It is the same that the APAX 5000 I O modules can be inserted back to the backplane when the system is pow ered on There are some PCI modules such as APAX 5090P which can only be inserted on the two slots on APAX 557X If you want to detach these PCI modules remember to power off the system before detaching them Then pull up the module lock and detach the PCI modules from APAX 557X The device must be fully dismantled in order to dispose of it Electronic parts must be disposed of in accordance with national electronics scrap regulations 3 3 Mounting 3 3 1 DIN rail Mounting APAX 557X can be mounted to the following DIN rails 35 x 7 5 mm or 35 x 15 mm Below are the procedures for the DIN rails mounting 1 Pull down the DIN rail lock at the back of APAX 557X APAX 5570 User Manual 32 2 Latch the APAX 557X to the DIN rail DIN rail E A i a eS 2 3 Slide the DIN rail lock of APAX 557X into the position to fix APAX 557X on the DIN rail 33 APAX 5570 User Manual 4 If more than two APAX 5000 I O modules are needed other APAX 5002 back planes are needed to attach to the DIN rail Pull down the DIN rail lock a
19. oftware program controlling when this LED is lit BAT When the battery runs out of power this LED will be lit ERR Programmer can use software program controlling when this LED is lit APAX 5570 User Manual 42
20. output USB Ports 4 USB 2 0 LAN Ports 2 10 100 1000 Mbps Serial Ports 2 COM 1 RS 232 COM 2 RS 422 485 Serial Baud Rate RS 232 50 bps 115 2 kbps Serial Baud Rate RS 422 485 50 115200 bps Storage 1 x SD card slot External Dimensions 270 x 142 x 126 mm Width x Height x Depth Weight Approximate 2 46 kg Cooling System Heat Sink with fan Power Input 18 30 VDC Supports dual power input and power input reversal protection Isolation Protection 2500 VDC between RS 422 485 and backplane Operating Temperature 10 55 C Vertical mounting Storage Temperature 40 70 C Relative Humidity 5 95 non condensing Shock Resistance 30 G wall mounting duration 11 ms tested to IEC 60068 2 27 Vibration Resistance 2 Grms wall mounting random 5 500 Hz 3 axes 1 hr axis Tested to IEC 60068 2 64 15 APAX 5570 User Manual 2 1 3 APAX 557X Dimensions
21. ow to build remote expansion APAX 557X supports backup function To leverage this functionality two CPU mod ules controllers with the same control program are installed in one system After both controllers have enabled the backup function APAX 5000 system will automati cally delegate one of the two controllers as the master controller The master control ler will run the control program to execute the control process while another controller the backup controller is put on standby APAX 5570 User Manual 2 The master controller will periodically send live messages to the backup controller If within 500 milliseconds it will automatically become the master controller take con trol responsibility and restart the control process The maximum operation time for the backup controller to become master controller the take over time won t be greater than 1 5 seconds Changing the master controller means there is something wrong with the previous master controller Therefore engineers can check or change the previous master controller with anew one and enable it to have backup function ality becoming a second backup controller Then if the new master controller fails again the second backup controller will automatically take control This mechanism ensures the system will continuously run the control process and won t be stopped even if controller fails In the figure below there are two APAX 557X modules installed in one system For e
22. peed Standard Ethernet cables can be used to connect any two APAX 5002 However shielded industrial Ethernet cable MUST be used instead of standard Ethernet cable when the system is used in harsh environment such as factory automation Unman aged industrial Ethernet switches such as Advantech EKI 2528 with 100 Mbps transmission speed can also be used between two APAX 5002 Therefore you can flexibly build any remote expansion with line tree or star topology All the APAX 5000 I O modules can benefit from the remote expansion architecture with local bus speed Refer to figure below for the expansion topology Warning 1 DO NOT use managed switch hub or router between backplanes for expansion 2 The network for the expansion should be a local network NOT to con nect with other external network such as public network in enterprise network including Internet 3 Cat 6 Ethernet cable is strongly recommended for better data trans mission quality 4 It is suggested to power on APAX 557X and all the I O modules together to avoid any unpredictable situation Warning For the line topology as shown by figure above the maximum distance between two backplanes is 100 m And there are maximum 30 APAX A 5002 backplanes used in the system for line topology to remain real time performance 25 APAX 5570 User Manual 155 GND Y Ethernet Switch a Warning For the star topology use an unmanaged industrial Ethe
23. rnet switch such as Advantech s EKI 2528 with 100 Mbps transmission speed for A expansion DO NOT use management switch hub or router between backplanes The network for the expansion should be a local network do not connect with other external network like public network in enter prise network including Internet APAX 5570 User Manual 26 3 1 2 Combine with APAX 5343 Power Supply Module As described in Section 1 2 APAX 557X can be power on by the power connector or APAX 5343 power supply module Refer to figures below for how to assembly APAX 5343 with APAX 557X 1 Pull up the module locks on the upper case of one APAX 5343 Then you can separate the upper case of APAX 5343 from its backplane Unlock 2 Then you can separate the upper case of APAX 5348 from its backplane 27 APAX 5570 User Manual 3 Remove the power connector on the left side of APAX 557X 4 Stack the backplane of APAX 5343 to the left side of APAX 557X 5 Lock the stacked APAX 5343 backplane with APAX 557X by the backplane locks on the APAX 557X APAX 5570 User Manual 28 6 Insert the upper case of APAX 5343 back on its backplane Use tongue and groove slots to move the upper case 7 Lock the upper case of APAX 5343 to its backplane by pulling down the module locks on the upper case Connect AC power code to the power connectors on the upper case of APAX 5343 Then the whole system is powered on 29 APAX 5570 User Man
24. t output USB Ports 4 USB 2 0 LAN Ports 2 10 100 1000 Mbps Serial Ports 2 COM 1 RS 232 COM 2 RS 422 485 Serial Baud Rate RS 232 50 bps 115 2 kbps Serial Baud Rate RS 422 485 50 115200 bps Storage 1 x SD card slot External Dimensions 270 x 142 x 126 mm Width x Height x Depth Weight Approximate 2 42 kg Cooling System Heat Sink fanless Power Input 18 30 VDC Supports dual power input and power input reversal protection Isolation Protection 2500 VDC between RS 422 485 and backplane Operating Temperature 10 55 C Vertical mounting Storage Temperature 40 70 C Relative Humidity 5 95 non condensing Shock Resistance 30 G wall mounting duration 11 ms tested to IEC 60068 2 27 Vibration Resistance 2 Grms wall mounting random 5 500 Hz 3 axes 1 hr axis Tested to IEC 60068 2 64 APAX 5570 User Manual 14 2 1 2 APAX 5571XPE CPU Intel Celeron M 1 5 GHz 1 MB L2 cache Memory 512 MB DDR2 DRAM onboard Dual Channel Mode Battery Backup Memory 512 KB Operating System Windows XP Embedded Diagnostic LEDs 1 x Power 1 x Run controlled by software 1 x Battery 1 x Error controlled by software 2 x LAN link activity link Real time Clock Yes battery backed Watchdog Timer Yes Reset Button Yes Control Software NET class library and C C API Power Consumption 45 W 24 VDC typical without module inserted VGA 1 DVI I interface Audio Interface MIC input Line Out
25. t the back of APAX 5002 backplane Unlock 5 Latch the APAX 5002 backplane to the DIN rail Repeat Step 4 Step 5 until necessary APAX 5002 backplanes are all attached on the DIN rail 6 Note When the total number of APAX 5000 I O modules is odd you can use APAX 5001 1 slot backplane as the last backplane in the system And the procedure to attach APAX 5001 on the DIN rail is similar as APAX 5002 7 Move all backplanes to stack all the backplanes and APAX 557X together Then slide the backplane locks on the backplanes to fasten all backplanes and APAX 557X Similar to Step 7 and 8 in section 3 1 1 APAX 5570 User Manual 34 8 Slide the DIN rail lock of all backplanes into the position to fix all backplanes to the DIN rail 9 Insert all necessary APAX 5000 I O modules to the APAX 557X slots and stacked backplanes Similar to Step 3 Step 5 Step 9 and Step 11 in section 3 1 1 10 Slide the module lock of all APAX 5000 I O modules into the position to fix these modules to related backplanes including APAX 557X slots Similar to Step 4 Step 6 Step 10 and Step 12 in section 3 1 1 3 3 2 Wall Panel Mounting Mount the APAX 557X module to a wall panel through backplane using 5 screws per module You can use 8 screws to strengthen the mounting Refer to figure below for the dimensional template
26. the wall panel is similar as APAX 5002 Note 6 Inserted all necessary APAX 5000 I O modules on the APAX 557X slots and the backplanes Similar to Step 3 Step 5 Step 9 and Step 11 in section 3 1 1 APAX 5570 User Manual 38 7 Slide the module lock of and all APAX 5000 1 0 modules into the position to fix these modules to related backplanes and APAX 557X slots Similar to Step 4 Step 6 Step 10 and Step 12 in section 3 1 1 Warning APAX 557X will generate a significant heat which is dissipated via a passive ventilation system This system requires the unit to be mounted correctly placed vertically In order to have better ventilation please keep enough space between the enclosure and adjacent equipment The APAX 557X can also be placed vertically for better ventilation Toward ground 50 mm Top 50 mm Toward amm ground Slide Slide APAX 5000 I O Module APAX 5000 1 0 Module APAX 5000 1 0 Module APAX 5000 1 0 Module APAX 5000 I O Module D N O 0 Ic gt Ts 0 Oe lt CL 50 mm Bottom 39 APAX 5570 User Manual APAX 5570 User Manual 40 Error Handling and Diagnostics 4 1 Error Handling and Diagnostics There are four LED for diagnostics on the front panel of APAX 557X When the LED is lit its color will become orange Below are the meanings for the 4 LED PWR When the APAX 5520 is powered this LED will be lit RUN Programmer can use s
27. tion of CRT VGA monitor to APAX 557X using a DVI to VGA adapter is also possible The adapter is available as an accessory Refer to figure below for DVI I pin assignments Crises efofnrlislalisfe Lzbelrefeol21 22 28 424 1 TMDS Data 2 13 N C 4 Analog DDC Clock Hot Plug Detect 5 Analog DDC Data 17 TMDS Data 0 DDC Clock TMDS Data 0 DDC Data TMDS Data 0 Shield S Analog Vertical Sync Pin Assignment cross in Assignment Analog Red Video Out C2 Analog Green Video Out 3 Analog Blue Video Out 4 Analog Horizontal Sync 5 Analog Ground Battery Backup RAM and SD Card APAX 557X provide 512 KB battery backup RAM for saving important data This ensures that you have a safe place to store critical data You can now write software applications without being concerned that system crashes will erase critical data from the memory When the external power for the system is loss the battery can continu ously provide power to the battery backup RAM to keep the data 7 APAX 5570 User Manual There is a BAT LED on the front panel of the APAX 557X Please replace the lithium battery with a new one if the BAT LED is activated Meaning battery runs out of its power Note The battery is special designed to connect with APAX 557X Spare bat Tas teries can be ordered from Advantech Warning Don t turn off the external power supply connected to APAX 557x when changing the battery to prevent from data loss in battery ba
28. ual 8 APAX 557X supports dual power input If you need the second power input repeat step 1 step 2 to separate another APAX 5343 9 Stack the backplane of the second APAX 5343 to the left side of the first APAX 5343 When you stack the backplane of the second APAX 5343 to the first APAX 5343 remember to turn off the power connected to the first APAX 5343 If not the backplanes may be damaged Turn on the power again after you complete the assembly for second APAX 5343 Warning A 10 Lock the second APAX 5343 backplane with the first APAX 5343 by the back plane locks on the first APAX 5343 APAX 5570 User Manual 30 11 Insert the upper case of second APAX 5343 back on its backplane Use tongue and groove slots to move the upper case 12 Lock the upper case of the second APAX 5343 to its backplane by pulling down the module locks on the upper case Connect AC power code to the power con nectors on the upper case of the second APAX 5343 Then there are two power supply modules for the whole system 31 APAX 5570 User Manual 3 2 Decommission and Disposal The procedure to disassembly APAX 5000 I O modules are opposite to the proce dure of assembling APAX 5000 I O modules Before detaching every APAX 5000 I O modules pull up the module locks first And then detach the APAX 5000 I O modules from the APAX 5570 or APAX 500x APAX 5001 or APAX 5002 backplane APAX 5000 I O modules support hot swap funct
29. y under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer Part
Download Pdf Manuals
Related Search