PLCBUS IR Motion Sensor - X10
Contents
1. Rated Dissipation lt 1W Load 300W resistive load 100W inductive load Working Temperature 10 C 40 C Working Humidity lt 85 Detection Zone 120 Side view x 360 Top view Delayed Channel CH1 CH2 Delayed Time 1 3 5 10 20 min and another six intelligent levels Active Illumination 10Lx 500Lx Mounting Height 1 8m 3m Dimension 110mm x 47mm Factory Setting Active illumination in the middle and the delayed time is 1 min 6 Notice e Avoid installation in the area that direct under sunshine air and temperature changes significantly Such as outdoor or beside AC heating fan Avoid production which is a strong reflection of the object Such as glass surfaces smooth metal surface In the monitoring area should not be blocking things Do not use sharp hard objects or coarse pollutants grazing lens Prevent the water spray Power must be cut when installation 3 32. Automation Home www automation at home com PLCBUSII T 4220E PLCBUS IR Motion Sensor 1 Main Features PLCBUSII T4220 This product uses pyroelectric infrared sensor to detect IR of human body moving and then send out a PLCBUS commands also have one load appliance can be connect to the device As long as the human body in its cross section through the detection range red indicator light flashes and turn on the lights and send PLCBUS ON command after delay a specific time it will turn off the lights and send PLCBUS OFF command During lights on if detect body moving will accumulate delay time 2 PLCBUS Scene Setup PLCBUSII T 4220 Scene emitter can control 16 addresses at the same time 2 1 Press and hold Setting button for 5 seconds and the indicator flickers ve e GeO a ee Setting LED Use any PLCBUS controller to send the address K N AN Button 2 2 Total 16 addresses entered exiting automatically MF aw y i 2 3 Tap Setting button once for exiting by force 2 4 Press Setting button for 5 times continuously and the last time holding the button for 5 seconds and the Beep long once for 1 phase Beep short 3 times for 3 phase the default setting is 1 phase 2 5 Press and hold Setting button for 15 seconds it turns to default Y N x setting oe atl 2 6 Screw it to the base after setting 3 IR setup This product can set 3 settings on the left of
3. enter Inactive Mode Hints If you want the device always in Active Mode please adjust Preset Illumination level knob to Right sign Inactive Mode working status Local Connected Appliance Indicator LED PLCBUS Command Active Mode working status Detect Local Connected Indicator LED PLCBUS Command i No Motion Detected No command will send Motion Detected Detected e a t Send ON command Detected Detected After Delayed time Send OFF command Duration of lighting limited The duration of lighting limited is 6 hours when it is over 6 hours loads will be turned off constrainedly later work as follow Night Working Status Daime a Last less than 1H get into Night working status Daytime Working Status Last more than 1H get into Night working status 4 Notice Base screwed to the appropriate location on the ceiling Connect power line and load as drawing Clockwise rotate the main object to fix it to the base 2 3 Automation Home www automation at home com PLCBUSII T 4220E Black phase Ac220v white neutral wire pea pe Red Load wire i oi LL W all i l ie al Adjustor at dta Installation Diagram Connection Diagram Side View Notice This device can connect to one load appliance And it will also work fine without connect to any loading 5 Technical Parameters Rated Voltage 220V 10 50Hz
4. the panel is Preset oa AN k Illumination level adjust knob On the right of the panel S L is delayed o a oe a p I time adjust knob At the bottom is the delayed channel switches CH1 p aw bee l CH2 l l i Delayed channel switch Choose CH1 could through set delayed time adjust knob pointing left j middle and right to choose the delayed time as 1 3 and 5 minutes umararo e E E Choose CH2 could through set delayed time adjust knob pointing left middle and right to choose 10min 20min and intelligent delay 20 10 or 5min Intelligent time delay perceived by the micro controller integrated frequency the duration of lighting and lighting times conditions to determine a specific delay time Delayed time adjust knob Unit Min e E E relig 20 10er8 1 3 Automation Home www automation at home com PLCBUSII T 4220E Preset Illumination level knob Left sign Middle lt gt Right sign Preset Illumination Level When power on there is 30s for testing of lighting During this time indicator is flickering with 2Hz frequency If all connection supply power and load are right than load on 30s later this product gets into normal working status If installation environment s Illumination level is lower than preset Illumination level then device will enter Active Mode If installation environment s Illumination level is higher than preset Illumination level then device will
Download Pdf Manuals
Related Search