S410E-SL MANUAL ISS1
Contents
1. and address and date of purchase Whatis covered Replacement parts amp labour on a back to base basis return transportation to the consumer main land U K only What is not covered Transportation from the consumer to Air Arms Damage caused by misuse abuse lack of routine maintenance transit damage between the dealer supplier and the consumer or unauthorised disassembly Parts subject to normal wear and tear Any other consequential cost incurred by the consumer Return transportation to consumers outside mainland U K No warranty is implied as to the fitness for any particular purpose AIR ARMS RESERVE THE RIGHT TO ALTER THE CONSTRUCTION APPEARANCE OR PERFORMANCE OF ANY PRODUCT WITHOUT PRIOR NOTIFICATION ALLILLUSTRA TIONS ARE FOR INFORMATION PURPOSES ONLY AND DO NOT NECESSARILY SHOW THEEXACT MODEL THAT WAS PURCHASED GENERAL MAINTENANCE AND LUBRICATION MAINTENANCE Fixings Regularly check the tightness of all fixings However do not be tempted to over tighten as some parts are made from aluminium and stripped threads may result Stripped threads are not covered by the manu facturers warranty Barrel For ultimate accuracy clean and re lube the barrel frequently It is difficult to advise how often 15 best for every circumstance but every 250 shots 15 not too often if the desire is to keep the barrel in the best possible condition The correct materials are very important Air arms only uses produc2. tes i ONIVV38 1795 el o fa YIdINVL LLNV LNNOWN 39NY9 1vOv9S 9 JVA ONIS 990tS S ASSY 3A1VA ONIMIS 0465 bt ons on ars So NI tay vt NO ETZSe CEN O ls AE 43431301S A908 MVA DAA asos Aao NoOHdiH2S3Q LW ON WLI i Air Arms Unit 6 Hailsham Industrial Park Diplocks Way Hailsham East Sussex England BN27 3JF Tel 01323 845653 Fax 01323 4405 3 Website www_alr arms co uk Email general air arms co uk Notes 16
3. the trigger guard Clockwise rotation increases pull weight If adjusted too far the spring will become coil bound And prevent trigger operation The second stage adjuster b 1s the rear screw located in the trigger blade This screw determines the exact point that the 2nd stage starts If the Ist stage screw 1s incorrectly adjusted this screw may not have any effect The first stage adjuster c 1s the front screw located in the trigger blade This screw determines the length of travel before the 2nd stage starts Clockwise adjustment reduces the first stage travel This rifle 15 fitted with a manual safety button located in the trigger blade To make the rifle safe the button must be pressed until it 1s flush with the side of the trigger blade Please note that it is possible to stop the safety button working with incorrect trigger adjustment With the button pressed in the rifle is safe With the button out the rifle is now ready to fire S32 54205 FILLING INSTRUCTIONS NOTE ONLY USE CLEAN DRY AND FILTERED COMPRESSED AIR PREFERABLY FROM A DIVING SHOP OVER PRESSURISATION MAY DAMAGE THE CYLINDER BEYOND REPAIR First the female part of the filling kit this was supplied with the rifle must be fitted to your filling equipment The female part S475 has a 1 8th BSP male thread that screws directly into the hose of your pump or bottle Next remove the dust cover from the end of your rifle This is achieved by unsc
4. MODEL S510 SL M Y CARBINE L2 AIR ARMS World Class Air Rifles USERS HANDBOOK THIS HANDBOOK REFERS S510 SIDE LEVER MODELS PLEASE READ THIS MANUAL BEFORE USING YOUR NEW RIFLE IT CONTAINS IM PORTANT SAFETY INFORMATION AND INSTRUCTION ON ADJUSTMENT AND MAINTENANCE Illustrated with optional telescopic sight and mounts wee SAFETY CODE I TREAT THIS AIR RIFLE AS IF LOADED 2 NEVER POINT IT AT ANYONE EVEN IF UNLOADED 3 NEVER LEAVE THIS RIFLE UNATTENDED WHEN COCKED OR LOADED 4 ALWAYS BE SURE OF WHAT LIES BEYOND YOUR TARGET 5 ALWAYS CONDUCT YOURSELF IN A SPORTSMAN LIKE MANNER ALWAYS BE AWARE THAT YOUR ACTIONS WILL BE UNDER THE SCRUTINY OF OTHER MEMBERS OF THE PUBLIC WHO MAY NOT SHARE YOUR ENTHUSIASM FOR AIR WEAPONS BAD PRACTICES PROMOTE BAD PUBLICITY DO NOT JEOPARDISE YOUR FUTURE ENJOYMENT BY MISUSING THIS WEAPON WARNING UNAUTHORISED DISASSEMBLY OF THIS RIFLE WILL INVALIDATE THE MANUFACTURERS WARRANTY ISSI 1 Contents of Box S510 Rifle Tool kit consisting of 1 1 5mm allen key 1 x 2 5mm allen key 1 x female filling adaptor Manual IMPORTANT INFORMATION PLEASE READ Before leaving the factory this rifle was Q A inspected and test fired using Air Arms PELLETS to check operation and final adjustment It was dispatched 1n a sealed purpose designed box with a contents label on the lid Air Arms may not be responsible for any damage to the contents or missing items if th
5. TNG 85 Soss 1S 1SOd SNIX3QNI YSTSS 9S TO ssl 31W1d 3015 TOENE 1500500 ss L 1117 st ONIN O luOddns TUU va el cc 15 HO8ES l sleet aaj SORCBEENENGERE dINV 12 LNOYS Aa TX asa e WariioxGniNS 775 16 cs nsswonows ses zs Wr SwmdsTmnd3oiuogw ges Oz Ls Omw suwS 1s ONN O INVA NM zzgs Gt 1 suwve Som o m i am EN 00056 Wr asooo ster a EN INoddnssenriswve os er PE ONO AA 9 Eu Tr ENT IONES EN SNIE O WODINNODTWA Us SL CC 3HHV8 JEOrS E AGO 3A1VA ONIT114 1675 tI E TONS ONES NIV MoNwvo zn er NIV es vr Wir PEI SP9s zi L3 weossswis te Jj 1 9wWorrss t 1 Hsn8 ros zv Nssxew eN Or EN Wii3os uxmus os 6 3 77 ov eft 80058 oes e EN Je Oy 8 Lz13 ANI ONDIDOD 7925 Hsne SAST 358
6. e box is not original if itis damaged or the seals are not intact Air Arms cannot be held responsible for damage or missing items due to transit damage mishandling or being tampered with after leaving the factory If this rifle 15 not received in the original box with the seals intact please examine carefully for any damage missing tools or documentation In the first instance any problems or complaints regarding this product should be referred to the supplier The air cylinder is a highly pressurised unit that must not be modified in any way Serious personal injury may result if this and the advice below is not followed Do not pressurise the cylinder if there are any surface abrasions or dents Contact Air Arms for advice Do not store the rifle in places with or near sources of high temperature such as fires or boilers Do not attempt to dismantle when pressurised Do not pressurise beyond the stated filling pressure see filling instruction section Damage caused by such action is not covered by the manufacturers warranty Only use clean filtered and dry compressed air Never use any other gas particularly industrial or welding gases such as oxygen carbon dioxide acetylene hydrogen argon etc If compressed air is being used other than from a diving shop the inside of the cylinder should be inspected for corrosion at least annually Ifin doubt contact Air Arms for advice In any event the cylinder should be inspected every tw
7. g to be in feet per second FPS Use fine measurement scales to weigh the pellet If scales are unavailable the pellet weight may be stated on the pellet container lid or contact the supplier The formula requires the weight to be in grains To convert from grams to grains multiply by 15 432 i e 0 69 grams x 15 432 10 65 grains To find the muzzle energy in ft lbs use the formula FPSxFPSxGrains 450240 i e 700x700x10 65 5218500 divide by 450240 11 59 CURRENT LEGISLATION LIMITS NON FAC HOLDERS TO AIR RIFLES WITH A MAXIMUM OF 12ft Ibs MUZZLE ENERGY WARNING IT IS A VERY SERIOUS OFFENCE TO BE IN POSSESSION OF AN AIR RIFLE THAT YOU ARE NOT CERTIFICATED FOR CONVICTION CAN RESULT IN CONFISCATION OF YOUR RIFLE A HEAVY FINE OR IMPRISONMENT EVEN A COMBINATION OF ALL THREE Do not store this rifle in a damp place such as garden shed or garage Do not store this rifle in a plastic or PVC gun bag without first applying a surface corrosion inhibitor Always ensure the loading bolt is fully closed before firing mF ITEDLIABILITY WARRANTY vv This product is warranted to the retail customer for 12 months from date of purchase against defects in materials and workmanship and is transferable to any subsequent owner Proof of purchase is required to receive warranty repairs retain your purchase invoice and return the warranty registration card as soon as possible after purchase The warranty card must show the dealer supplier name
8. his handbook This is best performed by a competent gun smith or the factory and in any case should not be required until the annual service Apply a small dab of grease or oil on the two pivot points shown in the diagram and work in by moving the bolt forwards and backwards Wipe off excessive grease Pre ferred grease is g95 gun grease On return from every shooting session wipe all over the exterior with an oily rag to preserve the surface finish during storage 5 OPERATING INSTRUCTIONS COCKING Hold securely in one hand and with the other pull the cocking lever out and to the rear At the end of the stroke the magazine will index and present a new chamber also the trigger mechanism will engage This can be determined by the trigger blade kicking forward at the end of the cocking stroke The effect required to cock the gun is quite low so minimal force should be used Note Itis very important that the cocking lever is pulled back to the correct position In one posi tive motion The magazine indexes to the next pellet position as the bolt is retracted and it 1s possible for a partial index if the lever is not pulled back fully If you find the mechanism has not cocked completely but the magazine has indexed Re cock but before closing the bolt remove the magazine and manually index it back to the empty chamber Replace the magazine and fire as normal If this procedure is not followed it is
9. hose will equalise and then the rifle will start to fill If you are filling your rifle from empty there may be some air exhausted through the barrel until the air pressure 1s sufficient to over come the firing valve spring S306 this will happen at approximately 50 bar 750psi The filling pressure of the S510 is 190 bar 2750psi Filling to a higher pressure will not increase either power or number of shots Over filling will lower the power and may cause irreparable damage to the cylinder Once the filling pressure has been reached close the valve on the bottle or stop pumping open the bleed valve on the filling kit to vent the hose if you do not vent the hose you will not be able to remove the female from the rifle Now the female connector can be removed from the rifle and end cap S483 can be replaced over the male connector ensuring not to over tighten The S510 range of rifles are fitted with a pressure indicator mounted on the underside of the rifle just in front of the stock screw This provides the user with a visual check on the amount of air remaining in the cylinder this indicator should not be used during the filling process as the needle reaction speed has been slowed to prevent damage whilst filling After filling the needle can take several seconds to synchronise with the air in the cylinder The picture below shows a guns with just over 150 bar of pressure Although every gun is slightly different the recommended ref
10. ill pressure for the 510 is between 100 and 110 bar NOTE On the front end of the cylinder is an engraved warning reading READ MANUAL MFP 200bar MSP 200bar DOM T45 INSPECTANNUALLY MFP Maximum Filling Pressure The pressure is stated MSP Maximum Safe Pressure The pressure is stated DOM Date of Manufacture The date is stated T45 Material used WARNING NOTE CONCERNING 300 BAR BOTTLES WITH THE ADVENT OF THE 300 BAR BOTTLE IT SHOULD BE NOTED THAT CARE HAS TO BE TAKEN WHEN FILLING YOUR RIFLE THE FILLING PROCEDURE DESCRIBED IN THIS MANUAL MUST BEFOLLOWED TO AVOIDED DAMAGE TO THE RIFLE PARTICULARLY THE SLOW OPENING OF THE VALVE ON THE BOTTLE OPENING THE VALVE QUICKLY WILL ALLOW UP TO 300 BAR OF PRESSURE INTO THE CYLINDER AT ONCE THIS COULD CAUSE SERIOUS PERSONAL INJURY OR IRREPARABLE DAMAGE TO THE CYLINDER 11 13 PLEASESTATE YOUR RIFLE NUMBER IN ANY CORRESPONDENCE 14 A BEE al 39 EI vEldj 9 aNIZVOWN LT SS TAE us XE JOOWIONdWWvONDOO 05 iE 15 LAT HSN 35H 1108 15 2055 15 2 HSN 35H 1108 15 TOSS LLV 4344N8 1N3130 1108 ONIGVOT TPIS 3NZvovwzc SSS 4309 L O o E Nid 13SSI8 YEZXL 9 Y34317 3015 IN31S 1108 INIAVOT ZZT Is vorss oz 43A31 3015 IN31S 1108 S9NIQVOT cC 15 80955 soss 09 ______________ zo es OW S
11. lance between the two stages and make the trigger inoperable if incorrectly adjusted If you have no experience of adjusting two stage triggers seek guidance or leave the trigger as set by the factory Note Incorrectly adjusted trigger mechanisms are not covered by the manufacturers warranty It is not possible to test this rifle with an incorrectly adjusted trigger therefore all triggers leave the factory with correct adjustment WARNING Please note that it is possible to stop the safety button working with incorrect trigger adjustment AN INCORRECTLY ADJUSTED TRIGGER CAN MAKE THE RIFLE UNSAFE TO HANDLE DESCRIPTION OF OPERATION The 5510 rifles have a true two stage trigger mechanism This means that as the trigger is pulled the bottom sear gradually disengages with the top sear until the two disengage completely and the rifle goes off If the pressure on the trigger 1s released at any point before full disengagement the bottom sear will auto matically return back to full engagement This type of trigger allows very fine but safe operation because it is the release of the 2nd stage that actually makes the rifle fire This arrangement is vastly superior to pseudo two stage triggers where the first stage 15 just a pivoting trigger blade that does not move sears The down side is that they are more difficult to adjust correctly ADJUSTMENT There are three adjuster screws a b c The weight of pull adjuster a 1s located in the front of
12. likely that you will load a second pellet into the barrel Push the lever back to the forward position The rifle is now cocked and loaded treat with caution MOUNTING DEMOUNTING THE MAGAZINE amp PELLETS DEMOUNTING Fully cock the rifle grip the magazine as shown in the first picture and slide out of the bolt housing without lifting Do not attempt to lift vertically as damage to the indexing spring will result MOUNTING Fully cock the rifle grip the magazine as in the sceond picture and slide into the bolt housing applying downward pressure with the fore finger to keep the base of the magazine against the bottom of the slot in the bolt housing Take care not to damage the indexing spring LOADING PELLETS Hold the magazine and drop a pellet into the chamber see below Manually index to the next empty chamber as in fig 4 and repeat until the magazine 1s full Finally line up the red dot on the pellet carrier with the v notch on the clear magazine cover Be very careful not to damage the Indexing spring when demounting or mounting the magazine Follow the instructions carefully pm Indexing Spring WARNING The rifle should only be fired when the magazine is fitted in the breech or damage to the seal carrier may occur TRIGGER ADJUSTMENTS The S510 models all have the same trigger mechanism It is a two stage unit with adjustment to both stages plus a weight of pull adjustment Itis easy to upset the ba
13. o to three years depending upon usage Air Arms can provide this service at a reasonable cost To maintain this rifle in good working order it should be serviced annually by competent gunsmith your supplier may be able to provide this service or contact air arms A reasonable amount of advice will be provided to enable the end user to service their own rifle however this is at the discretion of Air Arms and may not be given in all cases The velocity of this rifle has been set using Air Arms field pellets If any other make or type of pellet 1s to be used the rifle must be re tested with the pellet that is to be used to ensure the muzzle energy is within the limits determined by current legislation Due to the nature of hand pumps and their relative inefficiency in removing moisture from the com pressed air the chances of corrosion damage to the cylinder and other internal components are increased Therefore the rifle should be regularly serviced and or checked for any signs of damage by a competent gunsmith Air Arms recommend using a dry pack filter kit on any hand pumps used to fill our air rifles If accessories not manufactured by Air Arms are used on this rifle Air Arms can not be held responsi ble for any loss of performance Contact your supplier or Air Arms for any advice on this matter IMPORTANT INFORMATION Continued CHECKING VELOCITY Use a reliable chronograph to check velocity the formula below requires the readin
14. rewing the cover in an anti clockwise direction Once the connector is exposed the female part of the filling kit can be place on the male and press all the way on making sure that O rings on the male part are covered It is a wise precaution to hold the female part of the connector during the filling procedure as shown in the pictures below This will ensure the female adaptor is located completely over the male part and prevent any accidental dislodging of the connector before you start to refill the cylinder Using hand pumps The procedure for using hand pumps is the same as for bottle It is more important to turn the female on the gun to lock it in place When using the pump it must be remembered that the first few pump are filling the hose and NOT the gun When the pressure in the hose equalises to that in the gun the gun will start to fill It can take some effort to fill the gun using a pump and we reccomend using the pump to top up instead of filling from empty 10 With the female in place the gun can now be filled If the rifle is empty the mechanism will need to be cocked to allow the firing valve to close If the rifle is not cocked when the bottle is opened or the pump used the air will past the valve and exhaust through the barrel Check that the bleed valve on the filling equipment is closed turn clockwise to close then slowly open the main valve on bottle or start using the pump The pressure in the
15. ts made by napier Listed below is the napier product and a more generally available alternative If possible use napier for the best results CLEANER NAPIER GUN CLEANER ALTERNATIVELY WHITE SPIRIT OIL NAPIER GUN OIL ALTERNATIVELY 3 IN 1 OIL PULL THROUGH PAD NAPIER RIFLE CLEAN ALTERNATIVELY SOFT COTTON CLOTH PULL THROUGH LINE NAPIER PULL THROUGH KIT ALTERNATIVELY 205 FISHING LINE As a rule cleaners and oils intended for shotguns and small fullbore weapons are not suit able Cut a piece of three times the length of your barrel fold in half and tie ends together Remove silencer if fitted Open loading bolt 2 Feed un knotted end down barrel from the muzzle end until folded end protrudes about 50mm Cut a 100mm length of rifle clean 100x50mm piece of cloth and pass it between the pro truding loop Spray the pad with gun cleaner or white spirit turn the rifle upside down and pull the line back through the barrel slowly 4 Repeat steps 2 amp 3 until the pad is clean Repeat steps 2 amp 3 once more without cleaner on pad to dry barrel 6 Repeat steps 2 amp 3 once more with the pad sprayed with gun oil or 3 in 1 oil Important The reason for turning the rifle upside down is to prevent excess cleaner oil from passing down the transfer port into the firing valve chamber Lubrication Lubrication of the internal mechanism 1s not covered in t
Download Pdf Manuals
Related Search