User Manual Netti I Allround
Contents
1. Netti Allround ALU REHAB Thinking ahead moving forward C I This product conforms to 93 42 EEC for medical products CONTENTS 1 INTRODUCTION 1 1 Areas of use indications for Netti I allround 1 2 Contraindications 1 3 Quality and durability 1 4 Environment and disposal 1 5 Information for re use 1 6 About this manual 1 7 Vital measurements 2 QUICK REFERENCE 3 DESCRIPTION 4 FEATURES OF NETTI ALLROUND 5 ACCESSORIES 5 1 Assembly of Hip Belt 5 2 Assembly of H Belt 5 3 Push handles 5 4 Seat cushion 5 5 Head support 6 ASSEMBLING AND ADJUSTING 6 1 Unpacking 6 2 Main wheels 6 3 Front fork 6 4 Front castors 6 5 Seat height at the front 6 6 Seat height at the rear 6 7 Back rest 6 8 Adjusting seat depth at the rear 6 9 Adjusting seat depth at the front 6 10 Anti tip 6 11 Adjusting arm supports Language English Model Netti I allround Version November 2010 No oannia sf 17 17 17 17 18 18 18 19 19 20 20 21 kn iT fe is T 6 12 Back rest cushion 21 6 13 Adjusting the velcro back 22 6 14 Foot support 22 6 15 Adjusting the brake 23 7 TRANSPORT 24 7 1 Folding for transport 24 7 2 Transporting in car 24 8 MANOEUVRING 25 8 1 Driving general techniques 25 8 2 Driving step up 25 8 3 Driving step down 26 8 4 Driving slope 27 8 5 Driving up stairs 27 8 6 Driving down stairs 28 8 7 Transfer 28 8 8 Point of balance 29 82. Be aware of potential squeeze hazard between brake and tyre 7 TRANSPORT Netti I allround is tested and approved to crash test ISO 7176 19 7 1 Folding for transport When wheelchair is unoccupied fold as described below Put wheelchair in trunk or back seat When placed in back seat secure frame using safety belt e Turn the anti tips upwards Chapt 6 10 e Remove the arm supports Chapt 6 11 e Remove the foot supports Chapt 6 14 e Remove the back rest cushion Chapt 5 7 e Lay the back rest down onto the seat Chapt 6 7 e Remove the main wheels Chapt 6 2 e Remove the front castors Chapt 6 3 7 2 Transporting in a car If the head support is mounted correctly it is very stable but does not replace the need for an external neck support mounted in the car The chair is marked with stickers in 4 positions showing where to fix the straps 5 24 Language English Model Netti I allround Version November 2010 Netti I allround has been successfully tested according to the requirement of ISO 7176 19 using a combined wheelchair an occupant restraint system W120 DISR developed by Unwin Safety Systems For further information www unwin safety com In front Use hook or strap attachment Mount an eye bolt in one of the holes in the wheel frame bracket Hook on a hook carabine hook in the eye bolt Item number 1 pair eye bolts with bushing 21074 The angle of the straps should be
3. A Check that the safety screw is properly tightened To remove the handles the safety screw at the bottom also has to be removed 5 4 Seat cushion The seat cushion is fixed to the seating using the velcro It is imperative to correctly set up the cushion in order to ensure good seating comfort The cushion covers are washable and thereby reuseable Follow the instruction on the back of the cushion for correct maintenance and washing of the cushion 5 5 Head support A Lever for depth adjustment B Wheel for angle adjustment C Lever for height adjustment D Head support bracket Language English Model Netti I allround Version November 2010 15 e Place the squared nut in the trace of the head support bracket as shown above e Place the head support in the head Support bracket e The height and the depth of the head Support is set to the required positions and tightened e The head support bracket is fixed by tightening the four screws two by two diagonally so the bracket is fixed with the same strength divided on the four screws Adjusting the head support in depth e Release the locking lever on top of the vertical bar A e Adjust the head support and fix it in required position Adjusting the head support in height e Release the locking lever on the head support adapter C e Adjust the head support and fix it in required position Adjusting the head sup
4. brakes might be too tight e The user are sitting very askew in the chair e The user might be stronger on one side than the other e The main wheel hubs might be incorrectly mounted e Clean the front castors and forks for dirt e Too much weight over the front castors Adjust the point of balance by moving the main wheels back e Control that the front castors are not fixed too hard e Adjust the angle of the bearing house e Heavy weight over the front castors e Adjust the point of balance e Too much weight over the front castors Adjust the point of balance by moving the main wheels back e The front castors are not fixed properly e Check that the front forks are fitted in the same height e The angle of the bearing house might not be 90 e Clean and grease the quick release e Adjust the length of the hub bushing e Adjust the brake Check screws and adjustment points in general Please contact your dealer for information about authorized service facilities that can give support if solution is not reached in this form When in need of spare parts please contact your dealer When making changes affecting frame construction contact dealer manufacturer for confirmation 32 Language English Model Netti I allround Version November 2010 11 TESTS amp WARRANTY 11 1 Tests Netti allround is tested and has been approved for usage both indoors and outdoors The chair is CE marked Maximum use
5. down A Doing this increases the risk of tipping backwards This technique is only for very experienced users a e Check that the anti tip is turned up e Drive towards the step e Make a firm grip on the push rims and push fast forward so that the wheelchair comes down on all four wheels at the same time A Turn the anti tip down 26 Language English Model Netti I allround Version November 2010 Companions drive down a step backwards e Check that the anti tip is turned up e Move the wheelchair backwards to the step e Drive carefully down the step and move the wheelchair backwards on the main wheel until the front castors have come away from the step e Put the front castors down on the ground A Turn the anti tip down 8 4 Driving techniques Slope Important advise for driving down and up hill avoiding the risk of tipping A Avoid turning the wheelchair in the middle of a slope A Always drive as straight as possible As It is better to ask for assistance than taking risks Driving uphill Move the upper part of the body forwards in order to maintain the balance of the chair Driving downhill Move the upper part of the body backwards to maintain balance of the chair Control the speed of the chair by clutching the push rims Do not use the brakes 8 5 Driving techniques Up stairs A Always ask for assistance A Never use escalators even if assisted by a co
6. sunlight Never stand on the foot supports due to risk of tipping forwards Never lift the wheelchair by the foot supports or arm supports Product configuration may vary between different countries For visually impaired people manuals and catalogues can be downloaded at www alurehab com If in doubt contact your dealer 8 Language English Model Netti I allround Version November 2010 3 1 2 J on CON 11 12 14 15 16 17 Seat cushion accessory Release handle for Universal foot support Main wheel Quick release axle Push rim 10 DESCRIPTION Push bow Back rest cushion Uno Arm support with pad arm support Anti tip Brake Front castor bearing house Quick release for front fork 6 Front castor Heel strap Foot plate Be aware that specifications may vary between countries If any of these parts are missing please contact your dealer For complete information please contact your dealer Language English Model Netti I allround Version November 2010 9 4 eR pa ALU_REHAB 4 FEATURES OF NETTI I allround Accessories options Seat e Trays amp reading stand for trays See chapter 5 e Hip belts and 4 point belts See chapter 5 Hjul e Puncture proof wheels See chapter 5 e Pneumatic wheels See chapter 5 e Wheels with drum brake See chapter 5 e Wheels with one hand drive See cha
7. up a step backwards This technique is only useful if the step is very low It also depends on the clearance between the foot plates and the ground e Check that the anti tip is turned up e Drive the chair backwards towards the step e Make a firm grip on the push rims and move the body forward while pulling A Turn the anti tip down Companions drive up a step backwards e Check that the anti tip is turned up e Pull the chair backwards next to the step e Angle the wheelchair backwards moving the front castors slightly up in the air e Pull the wheelchair up the step and go backwards long enough to put down the front castors on the step A Turn the anti tip down 8 3 Driving techniques Step down Users drive down a step forwards Companions drive down a step forwards e Check that the anti tip is turned up e Angle the wheelchair backwards moving the front castors slightly up in the air e Drive carefully down the step and angle the wheelchair forward putting the front castors back on the ground Turn the anti tip down Users drive down a step backwards This technique is only for very experienced users This technique should not be used if the height of the step is more than 10 cm e Check that the anti tip is turned up e Move the wheelchair backwards to the step e Move carefully down the step backwards while moving the body forward to keep the balance of the chair A Turn the anti tip
8. 0 45 8 MANOEUVERING 8 1 General techniques The weight and balance of the chair influences the manoeuvering abilyty of the wheelchair The weight size and sitting position of the user are also influencing factors Also the position of the wheels will influence the driving ability The more weight placed over the main wheels the easier it is to manoeuvre If heavy weight is placed over the front castors the chair will be heavy to manoeuvre Companion If the user is left alone in the wheelchair always lock the brakes and secure that the anti tips are turned down Parking Increase the underneath support of the wheelchair by moving the chair about 10 cm backwards making the front castors turn forward 8 2 Driving techniques Step up Users drive up a step forwards This technique is only for very experienced users e Check that the anti tip is turned up e Drive close to the step e Balance the wheelchair on the main wheelso that the front castors are lifted high enough to enter the step e Make a firm grip on the push rims and move the body forward while pushing A Turn the anti tip down Language English Model Netti I allround Version November 2010 25 f F MT Companions drive up a step forwards e Check that the anti tip is turned up e Angle the wheelchair backwards e Lift the push handles while pushing the chair onto the step A Turn the anti tip down Users drive
9. 2 24 and 26 12 Language English Model Netti I allround Version November 2010 One hand drive 20 22 24 26 x 13 8 20 22 and 24 x 1 In addition you must order a tele scopic connection bar for the wheels Front castors Several models in 3 a 5 6 7 and g Front forks Standard w axle Long w axle Short w axle Wide w axle Long Wide w axle Sliding seat The seat can be pulled out and pusched in while the user sit in the seat This eases trans fer and positioning of the user Comfort plate The plate has a hole in the rear which in co cushion increases pelvic stabilization Calf pad hinged The user doesn t have to lift the legs when mounting or dismoun ting the foot supports Foot board with lock The foot supports can be swung to the side like standard foot supports Language English Model Side support Correction Meant for correction of bad postures in the upper trunk For optimal function use together with Flip back rest Pad for side support Correction Side support Stable Meant for users with de creased stability of the upper trunk For optimal function use together with Stable cushion Pad for side support Stable El components For tilt back rest and foot supports seperate or complete Frame extender Increases distance between main wheels and front castors Reduces tipping risk Upholstery for calf support brack
10. 9 Lifting the chair 29 8 10 Push rim 30 9 MAINTENANCE 31 9 1 Maintenance 31 9 2 Cleaning and washing 31 10 TROUBLESHOOTING 32 11 TESTS AND WARRANTY 33 11 1 Tests 33 11 2 Guarantee 33 11 3 Claim 33 11 4 Spare part guarantee 34 11 5 Special adjustment adaptations 34 11 6 Combination with other products 34 11 7 Service and repair 34 12 MEASUREMENTS AND WEIGHTS 35 Language English Model Netti I allround Version November 2010 3 1 INTRODUCTION Netti I allround is a wheelchair meant for both indoor and outdoor use It is tested to DIN EN 12183 2009 The tests were carried out by TUV SUD Product Service GmbH in Germany In Alu Rehab we believe that wheelchairs should be chosen based on a thorough assessment focusing on the needs of the user and demands from the environment Therefore it is important to know about the possibilities and restrictions of the wheelchair Netti allround is a wheelchair designed for users with the need for comfort and relief The combination between the seating system and the ergonomical solutions in the frame construction offers many possibilities for adaptation and adjustments Max user weight 150 kg When mounting accessories such as power kit etc the weight of the accessories must be subtracted from the max user weight Specifications varies between countries Language English Model Netti I allround Version November 2010 1 1 Areas of use indicat
11. a better a increase decrease the distance grip but the friction may increase between the push rims and the wheel When using the hands to stop the Prase re your ARANG chair the risk for burning of the hands increases 30 Language English Model Netti I allround Version November 2010 9 MAINTENANCE 9 1 Maintenance instructions The Netti chairs are built of modules Alu Rehab carries stock of all parts and is ready to supply these on short notice Necessary instructions for mounting will follow the parts Parts to be handled by user are defined in spare part catalogues that can be downloaded at www alurehab com These parts can if needed also be removed and sent to manufacutrer distributor upon request Parts related to wheel frame construction must be handled by manufacturer or authorized sercvice facility You can order original paint from Alu Rehab to repair scratches and minor damages to the paint Please contact your dealer to order if defects or damages occur please contact your dealer A Check re adjust screws and nuts at regular intervals Sand and sea water salt used for gritting in the winter can damage the bearings of the front castors and main wheels Clean the wheelchair thouroughly after use OD We recommend washing the wheel Weekly Monthly Check defects damages E g breakage missing X parts Twisting of wheekchar RI ong of bearings kn wasting o
12. aler Spoke protectors For 20 22 and 24 Black or transparent is optional Foot box Upholstred Abduction block The block reduces abduction Small 80 mm width Medium 120 mm width Large 140 mm width Language English Model Netti I allround Version November 2010 1 Foot support Angle adjustable Universal Adjustable in fixed positions between 33 to 105 using an adjustment wheel Amputation support Knee Thigh support The support reduces adduction Head supports Support C Large Support A Side support Support B Small Men Hygiene cover Protect the core of the head support Head cushion 40 x 40 cm cushion with Kospoflex filling and rubber band Head cushion Comfort Cushion with Kospo flex filling to pull onto head rest Back rest extender 12 cm extender To be used together with 60 cm back rest cushion Arm support pads Wide 415 x 80 mm Long 445 x 70 mm Long Wide 525 x 60 mm Short 333 x 58 mm Standard 38 x 58 mm Arm support bended Hemi arm support Offers extra support for the affected arm Can be set in fixed positions Hemi cushion A more accommodating Support than the hemi arm support Comfort pads To be attached to the skirt guard Offers a pressure distributing effect 2 5 3 5 and 4 5 cm Main wheels SP Several models in f R PR h site 24 and 26 Push rims Aluminium 20 2
13. anti tip will secure the chair from tipping backwards We strongly recommend use of the anti tips 1 6 About this manual In order to avoid damages while using the Netti allround wheelchair please read this manual carefully before starting to use the chair A Symbol of forbidden actions No warranty can be claimed when ever these actions are implemented Symbol of warning Whenever this symbol is used caution has to be taken Symbol for important information Symbol for useful tips Symbol for tools 6 Language English Model Netti I allround Version November 2010 1 7 Vital measures Netti I allround is a wheelchair designed for both outdoor and indoor use Specifications varies between countries Total weight 22 3 Kg 500 mm width chair Seat width 350 380 400 430 450 500 550 600 mm Seat depth From back rest cushion to front of seat plate 400 425 450 475 500 mm Seat height F Measured from floor to top of seat plate using 22 main wheels in upper hole position Standard Uno cushions measures 8 cm 390 mm By changing position of main wheels it is possible to achieve 32 47 cm seat height Backrest height 500 mm Using back rest extender gives 600 mm cat support Seat planeangle o Foot support to seat 280 mm 770 mm distance Leg to seat surface angle 182 Arm support to seat 185 mm 325 mm distance Front locat
14. el Netti I allround Version November 2010 35 ALU REHAB Bedriftsvegen 23 NO 4353 Klepp Stasjon NORWAY Tel 47 51 78 62 20 Fax 47 51 78 62 21 E mail post alurehab com www alurehab com UM0102UK
15. et Reduces pressure Tool set Netti allround Version November 2010 5 1 Mounting of hip belt 5 2 Mounting of H Belt bar Picture 1 e Remove the push handles and pull the H belt attachment bar onto the push handles from the lower end Picture 1 e Pull the belt thorough the hole in the hip belt bracket Picture 1 Picture1 Picture 2 PE e Fix the push handles in correct position I EE and lock firmly Then fix the bar at the right position height The height should be level with the shoulders of the user Picture 2 Picture 3 e Fix the hip belt bracket to the rearmost hole in the back hinge using the enclosed screws and nuts Picture 3 e Thread the belt through the rolls and lock the belt by pulling the belt through the belt clamp Adjust to the requested length of belt Picture 3 x 2 pcs 13 mm open end spanner Picture 3 14 Language English Model Netti I allround Version November 2010 5 3 Push handles Mounting of the push handles e Mount the push handles in the hole in every side in the push bow e Mount the safety screw and lock nut in the hole in the bottom of the push handles Adjustment of push handles e Release the lever on the side and lift the handle all the way up e Turn the handles into required position e Adjust height e Lock the handle in required position by tightening the lever Be sure to lock the handle properly
16. etti I allround Version November 2010 19 f F 7 By using the adjustment strap in the rear you can gain a few cm on the depth When adjusting the seat depth at the rear the screw in the back rest hinge must be tightened with 14 Nm x 6 mm Allen key 13 mm open end spanner When changing seat depth you also change the tipping point of the chair This can be prevented by changing the position of the main wheel in the main wheel bracket See chapter 6 6 6 9 Adjusting seat depth at the front It is possible to adjust the seat depth up to 10 cm at the front Do the following e Unfix the screw holding the pull out piece for the foot support e Set the pull out piece to the required position e Fix the screws tighten them with 25 Nm x 6mm Allen key By setting the pull out pieces to different positions it is possible to compensate for a rotated pelvis or different length of thighs 6 10 Anti tip e Adjust the anti tip so that it doesn t stick outside the radius of the wheel e Pull the anti tip out rearwards from chassis e Turn it down 180 e Lock it in position by moving forwards with Spring tension The anti tips are delivered adjusted according to ordered main wheel size in standard position If other adjust ments are carried out anti tips have to be adjusted accordingly Adjusting anti tip The anti tips must be adjusted whenever position or dimension of ma
17. f ewshions x cheek ant tip function Ka check brake adjustment _ X Check tyre wear Asa rule of thumb use oil on movable parts and all bearings Alu Rehab recommends use of ordinary bicycle oil 9 2 Cleaning and washing 1 Remove cushions before washing the wheelchair 2 Clean cushions and covers according to instructions printed on cushions Cushion cleaning procedures com gt Tato dave roe Tardy standing gwe omme 3 Clean frame using water and a rag chair in washing chamber at gt 85 C 4 If jet water washing avoid pointing For small damages to the surface original surface paint can be ordered from the manufacturer Language English Model Netti I allround Version November 2010 directly towards gas springs labels and back cushion 5 We recommend using soft soap 6 Wash the wheelchair well using clean water to remove all the soap 7 Use methylated spirit to remove any dirt left 31 y 10 TROUBLESHOOTING The wheelchair is going askew The wheelchair is heavy to manoeuvre The wheelchair is hard to turn The front castors are wobbling The main wheels are difficult to take off and put on The brakes are not functioning well The wheelchair feels shaky e The angle of the bearing house might not be 90 e Check that the front castors are fitted in the same height e The main wheel hubs might be incorrectly mounted e One of the
18. g house See chapter 6 5 6 7 Back rest The back rest can easily be folded down by pressing the release stay to allow to lay the back rest down onto the seat Ensure the back rest click back into position when raising it again The back rest angle can be changed in 3 different positions Standard back rest angle is 97 Alternative angles are 107 97 amp 83 To hange the angle of the back rest e Loosen the screw shown in the picture e Place the screw in the desired position e Tighten the screw To ensure that the screws are properly locked in position the edge of the screw should be parallel to the back rest hinge See picture 6 8 Adjusting seat depth at the rear The seat depth can be adjusted 10 cm in the rear and 10 cm in front Adjusting seat depth at the rear e The back rest hinge has 5 holes with 2 5 cm distance between e The seat depth can be adjusted from 40 50 cm Measured from front of seat plate to back rest tube without back rest cushion e Pull out the locking bolt for the back rest and place the back rest forward in the seat e Remove the screws holding the back rest hinge and set the back rest to the required position Do both side at the same time e Place the screws back and fix them When using the comfort seat plate it is recommended to change seat plate when changing seat depth The seat plate comes in depth 40 cm 43 cm and 46 cm Language English Model N
19. in wheels is changed 20 Language English Model Netti I allround Version November 2010 dn gt is Correctly adjusted anti tips should be positioned just on the inside of the radius of main wheel Anti tips are adjusted as follows e Unfix the locking clamp on the anti tip bar using an Allen key e Pull or push the bar to required position e Fix the locking clamp e Do the same procedure on the opposite Side x 6 mm Allen key A Check that both anti tips have the same length The gap between the anti tip wheels and the ground must be max 3 cm A if the anti tip is positioned on the outside of the main wheel radius it will interfere with curbs and stairs A The anti tip should always be used for the safety of the user 6 11 Adjusting arm supports e Turn the release handle to the side and hold e Adjust the armrest to the required height and release the handle Lift or lower the armrest slightly until it locks The armpad and locking screw are set in the middle position This can be adjusted to suit the user 6 12 Back rest cushion The back rest cushions are fixed and adjusted on the wheelchair using the velcro It is imperative to correctly set up the cushion in order to ensure good seating comfort The cushion covers are washable and thereby reuseable Follow the instruction on the back of the cushion for correct maintenance and washing of the cushion Language Engl
20. ion of arm 330 mm 460 mm support structure Push rim diameter Horizontal axle location 185 mm Model width 50 cm Measured without cushions Language English Model Netti I allround Version November 2010 7 2 0 QUICK REFERENCE The content of this page is a summary of the whole manual It gives you a brief introduction to the use and care of the Netti allround wheelchair A The quick reference is not a replacement for the manual only a reminder check list e Unpack the wheelchair Chapter 6 1 e Mount the main wheels Chapter 6 2 e Mount the front castors Chapter 6 4 e Mount the arm supports Chapter 6 11 e Lift up the back rest Chapter 6 7 e Mount the back rest cushion Chapter 6 12 e Mount the foot supports Chapter 6 14 e Mount accessory See chapter 5 for more information Mounting descriptions will accompany the accessory For troubleshooting see chapter 10 For adjustment see chapter 6 Drive carefully Be aware that friction against push rims can create a warm surface Salt water can increase risk of corrosion Further precautions related to environmental conditions not needed When the chair is tilted rearwards the anti tips and brakes should always be in use Be sure to lock all handles properly The anti tips should always be used for the safety of the user Surface temperature of metal parts in frame structure might increase when exposed to direct
21. ions for Netti I allround Netti I allround is a multi function wheelchair for partially or fully immobile persons with physical and or mental disabilities These disabilities may have multiple causes It is possible for the user to change the position mobilisation or posture correction stabilisation wherever the following functional impediments with their multiple possible causes are present e limited or lacking mobility e limited or lacking muscle power e limited movement range e lacking or limited trunk and body stability e hemiplegia e rheumatic type disorders e craniocerebral injuries e amputations e other neurological or geriatric disorders 1 2 Contraindications Netti allround is not suited for persons with a strongly enhanced muscular spasticity In this case we recommend the Netti HD which offers a version with reinforced frame and leg rests for this particular need Ignoring this advice could in unfavourable circumstances lead to the deformation or fracture of metal parts in the area of the back tube the leg rests or the arm rests Language English Model Netti I allround Version November 2010 1 3 Quality and durability The Netti allround wheelchair is tested at TUV SUD Product Service GmbH in Germany following the European Standard DIN EN 12183 2009 As manufacturer Alu Rehab A S evaluates the test to be equal to 5 6 years of normal use of the chair The disability of the user as we
22. ish Model Netti I allround Version November 2010 21 F E 777 _____ 6 13 Adjusting the velcro back Mounting of foot support e Mount the foot support be holding onto the bar bending down towards the foot plate Hold it in an angle of app 20 to the side frame Put it into the black plastic lock attached to the extracable adjustment bar Swing it in and push down e Loosen the straps and place the back rest cushion so that the user gets room for the bottom and the integrated lumbar support in correct position e Tighten the straps so that they follow the curvature of the spine and gives a little extra support at the top of the sacrum Adjusting the angle of the foot support 6 14 Foot supports e The angle of the foot support can be adjusted using the star wheel in center of the hinge point e Loosening this star wheel enables you to adjust the foot support to the required angle e Fix the angle by tightening the star screw Universal foot support The Universal foot support is fixed with the possibility of angle adjustment It is swingable and removeable The foot plates are foldable and can be angled in fixed positions 22 Language English Model Netti I allround Version November 2010 Oo dn SS So ies Adjusting the length of the foot support Removing the foot support a e Untighten the screw A to make the e Take the foot support off by pulling it up adjustment tube move and swinging it ou
23. just the point of balance by changing the position of the main wheel in the main wheel bracket e Move the main wheel hub and the main wheel Chapt 6 6 e Adjust the brakes Chapt 6 15 x 2 pcs 24 mm open end spanner 5 mm Allen key When the main wheels are moved forward it will be easier to manoeuvre the wheelchair but the risk of tipping backwards increases The point of balance can also be changed by adjusting the seat angle and or angle of back rest A Itis recommended to use the anti tip Check that the main wheel and quick release are locked properly Chapt 6 2 8 9 Lifting the wheelchair e The wheelchair should be lifted in the frame push bar and push handles only It is marked with the above symbol where it should be lifted AA Never lift the wheelchair by the foot supports or arm supports Language English Model Netti I allround Version November 2010 29 8 10 Push rim Netti I allround is delivered with aluminium push rims as standard The material and distance to the main wheel influences the ability of the user to grip Contact your dealer to get information about push rims A squeezing and trapping hazard of the fingers may occur when passing through narrow passages and if the fingers come between the spokes To avoid this risk we recommend spoke protectors as accessory that fit your chair l If you want need to change push rims Alternative push rims may give
24. ll as the level of maintenance done foremost decides the durability of the wheelchair Thus the durability will vary depending on these two factors 1 4 The environment and waste disposal Alu Rehab and its suppliers wish to protect the environment This means e That we avoid using environmentally harmful substances and processes to the greatest extent possible e That Alu Rehab s products are ensured a long service life and a high degree of flexibility to benefit the environment and economy e That all packaging can be recycled e That the wheelchair was designed to be separated into its component materials to make recycling easier Contact your local recycling agent to get correct information how to handle in you area f F Me EE 1 5 Information for re use All products from Alu Rehab are designed to give years of maintenance free service All products can be adapted for re use by an authorised dealer In order to guarantee performance and safety Alu Rehab recommends the following tests prior to any re use Please examine the following components for function integrity etc and replace parts as necessary e Wheels tyre tread e Wheelchair frame e Cushions e Hubs e Brake function e Headset bearings test for wear lubrication e Directional stability of wheels e Bearings Please also note the content of chapter 9 2 Cleaning and washing Anti tip Correctly fitted the
25. mation please contact your dealer or Alu Rehab A S Norway directly 11 7 Service and repair Information about service and repair services in you area please contact your local dealer OD A unique identification number serial number is to be found on the bottom frame on left side of the chair A spare part catalogue for the wheelchair can be obtained through your local dealer or downloaded at www alurehab com A refurbisment manual for the wheelchair can be obtained through your local dealer or downloaded at www alurehab com 34 Language English Model Netti I allround Version November 2010 7 12 MEASUREMENTS amp WEIGHTS Size Seat depth Back rest Total width Transport Weight Standard height width Extender Gjem sen Measured between edges of frame tubes For distance between skirt guards add 2 5 cm Measured from front of seat plate to back rest hinge without cushion Using standard Uno back rest cushion subtract app 3 cm Measured from seat plate to top of back rest velcro OD The weight is including main wheels front castors foot support and arm support No cushions Recommend inflation pressure using air tyres is 60 65 PSI OD Max user weight is 150 kg When mounting accessories such as power kit etc the weight of the accessories must be subtracted from max user weight Dealer Serialno Date supplied S a Language English Mod
26. mpanion With assistance backwards e Check that the anti tip is turned up and that the push handles are fixed properly e Pull the wheelchair backwards to the first step of the stairs e Angle the wheelchair backwards on the main wheels e Pull the wheelchair slowly up the stair one step at the time keeping the balance on the main wheel e Reaching the top of the stair pull the wheelchair backwards far enough to put the front castors safely down on the floor Turn the anti tip down If two companions are present one person can assist lifting in the front of the frame ZS Do not lift the wheelchair holding onto the foot supports Language English Model Netti I allround Version November 2010 27 f F 7 ZS Do not lift the wheelchair holding onto the arm supports The companions should use the strength in their legs carrying the chair avoiding unnecessary stress on the back 8 6 Driving techniques Down stairs A Never use escalators even if assisted by a companion With assistance forwards e Check that the anti tip is turned up and that the push handles are fixed properly e Drive the wheelchair forward to the first step of the stair e Angle the wheelchair backwards on the main wheels e Have a firm grip on the push handles and keep the balance on the main wheel taking One step at the time e Reaching the bottom of the stair put the front castors safely down o
27. n as a defect is discovered Language English Model Netti I allround Version November 2010 33 as Normal wear incorrect use or incorrect handling is not a reason for claims A The user is to use maintain and handle the wheelchair as described in the user manual 11 4 Spare part guarantee e Alu Rehab offers a 5 year guarantee as a minimum for spare parts The periode of guarantee is defined as beginning at the date Alu Rehab cancels the production of a specified type of chair e During the periode of spare part guarantee Spare parts are delivered within 14 days e During the periode of spare part guarantee Alu Rehab offers a 1 year guarantee for defect spare parts 11 5 Special adjustment adaptations Special adjustments adaptations are defined as all adjustments that are not included in this manual Wheelchairs that are especially adjusted adapted by the customer can not keep the CE mark given by Alu Rehab A S Norway If this is the case the warranty given by Alu Rehab A S Norway will not be valid If any uncertainty about special fitting and adaptations please contact Alu Rehab A S 11 6 Combinations with other products Combinations of Netti and other products not manufactured by Alu Rehab A S Generally in these cases the CE mark of all the products involved will not be valid However Alu Rehab A S has made agreements with some manufacturers about somecombinations For further infor
28. n the floor turn the anti tip down If two companions are present one person can assist lifting in the front of the frame As Do not lift the wheelchair holding onto the foot supports Do not lift the wheelchair holding onto the armrests 28 Language English Model Netti I allround 8 7 Transfer Techniques for transfering to from the wheelchair should be practiced well with the persons involved Here we give some important advices for preparation of the chair With or without companion sideways Before transfer e The wheelchair should be placed as close as possible to the destination of the transfer e Pull the wheelchair backwards 5 10 cm in order to make the front castors turn forward e Lock the brakes e Remove foot support and arm Support on the side of the transfer Version November 2010 With or without companion forwards Before transfer e The wheelchair should be placed as close as possible to the destination of the transfer e Pull the wheelchair backwards 5 10 cm in order to make the front castors turn forward e Lock the brakes Using a lift Before transfer to chair e Remove the foot supports e Open the back rest angle slightly e Replace the components when transfer is finished Never stand on the foot plates without making sure that they are touching the ground due to the risk of tipping the chair forwards 8 8 Point of balance Ad
29. ngle adj 2 kg each Uno Back 1 25 kg VB Sit 1 kg Head support A 1 kg Head support C 0 9 kg Necessary tools are described under each chapter Accessories described in chapter 5 is a presentation of options and will be delivered with separate mounting descriptions 6 2 Main wheels To mount the main wheel remove the quick release bolt from the hub bushing lead it through the centre of the main wheel and into the hub bushing while pressing the knob in center To check that the main wheel is properly attached to the hub remove the finger from the central knob and pull the main wheel If the main wheel doesn t lock don t use the wheelchair but contact your dealer Sand and sea water salt used for gritting in the winter can damage the bearings of the main wheels Clean the wheelchair thoroughly after exposure 6 3 Front fork Front forks come as standard with quick release axles The front fork is easily removed by pressing the knob in centre above the wheel Chek angle of castor bearing house See chapter 6 5 Quick Release Language English Model Netti I allround Version November 2010 17 f F MT EE 6 4 Front castors To take of e Press the release button under the front fork To mount e Lead the quick release axle into the bearing house Pull the fork slightly to ensure that the fork is fully locked Sand and sea water salt used for gri
30. port in angle e Release the adjustment wheel at the rear of the horizontal bar B e Adjust the head support and fix it in required position Adjusting the head support sideways e The head support adapter can be moved both to the right and left giving the possibility to accomodate special needs for head support e Untighten the four screws holding the adapter together e Move the adapter to the required position and fix the adapter by tightening the screws diagonally A Remember to release the levers when adjusting the head support If the head support stand does not fit the bracket perfectly the bracket is probably fixed too tight or unevenly After fitting the head support fix it properly by tightening the little set screw in the centre on top of the head support bracket using an Allen key If the head support seems to short in height it can be turned 180 by releasing the adjustment wheel at the rear of the horizontal bar B 16 Language English Model Netti I allround Version November 2010 6 ASSEMBLING AND ADJUSTING 6 1 Unpacking See chpt 5 amp 6 1 Unpack all the parts and check that everything is there according to the packing list 2 Mount main wheels and front castors 3 Mount back rest arm supports cushions and foot supports 4 Mount accessories Weight of components 45 cm width chair Main wheels 1 9 kg each Front castors 0 8 kg each Foot support a
31. pter 5 e Pneumatic front castors See chapter 5 e Spoke protectors See chapter 5 e Push rims See chapter 5 Back rest e Back rest extender See chapter 5 e Lumbar support and Wedge See chapter 5 e Back rest cushions Foot support e Angle adjustable foot support See chapter 5 e Amputation support See chapter 5 e Knee and thigh support See chapter 5 Arm support e Different pads See chapter 5 e Hemi arm rest and Hemi cushion See chapter 5 Head support e Different models See chapter 5 10 Language English Model Netti I allround Version November 2010 5 ACCESSORIES Belts Several models Hip belts with or without upholstery and with plastic lock or car lock See chapter 5 1 and 5 2 for mounting H Belt attachment bar To be mounted onto the push handles Come in two sizes with telescopic bar See chapter 5 2 Trays 3 models Swingable lockable and standard push on model Reading stand Upholstery for tray Offers a soft base for the arm resting on the tray Half tray Swingable upholstered half tray The tray replaces the existing standard armrest Wedge Increases side support Lumbar support Increases lumbar curvature Brake extenders 90 mm 120 mm 250 mm LI VN Vital Base Integral Pelvic stabilizer Seat cushions Many to choose from Please contact your dealer Back rest cushions Many to choose from Please contact your de
32. r weight 150 kg It is tested by TUV SUD Product Service GmbH according to DIN EN 12183 2009 a Crash tested at Millbrooke Proving Ground Bedford UK according to ISO 7176 19 Seating system is tested for fire resistance according to ISO 7176 16 11 2 Guarantee Alu Rehab is providing you with a 5 year guarantee on all frame components and on the cross tube assembly There is a 2 year guarantee on all other compo nents except batteries Alu Rehab is not responsible for any damage resulting from inappropriate or unprofessional installation and or repairs neglet wear from changes in wheelchair assemlies or instutions not approved by Alu Rehab or by use of spare parts delivered or produced by third parties In such cases this guarantee shall be considered null and void 11 3 Claim e Claim is to be addressed to the sales agent of the wheelchair Please note that sales documentation has to be filled in and signed correctly in order to document time and and place of the purchase of the wheelchair e Generally defects are accepted as reason for claims The sales agent and Alu Rehab are to decide whether a defect has to be repaired or the customer is entitled to a reduced prize due to the defect e This decision is based on an evaluation of defect 14 days after receiving a claim the customer receives a report from the sales agent and or Alu Rehab are going to handle the defect e Claim are to be forwarded as soo
33. t Ill 6 14 2 e Adjust the foot support in required position and fix the screw properly Adjusting the angle of the foot plate Il 6 14 2 e The foot plates can be adjusted in angle e Untighten the screw B and adjust the foot plate to the required angle Fix the screw properly Ill 6 14 1 A Never lift the wheelchairs by the foot supports A Never stand on the foot supports 6 15 Adjusting the brakes e The brakes are freely adjustable along the frame tube e To activate the brake push the handle forward Ill 6 15 1 Il 6 14 1 x 5 mm Allen key While making the adjustment there must be no load on the foot plates Ls For outdoor use there should be a clearence of 4 5 cm between the foot plate and the ground IIl 6 15 1 Language English Model Netti I allround Version November 2010 23 e To release the brake pull the handle rearwards Ill 6 15 2 III 6 15 2 e To reposition the brake loosen the two screws on the inside of the brake clamp Ill 6 15 3 e Adjust the brake position and tighten the screws Il 6 15 3 e For fine adjustment loosen the upper screw on the inside of the brakes III 6 15 4 Ill 6 15 4 x 5 mm Allen key A Check that the brakes are correctly adjusted by activating the brakes and be sure that the wheel chair doesn t move The brakes are constructred as parking brakes and shall not be used as driving brakes
34. tting in the winter can damage the bearings of the front castors Clean the wheelchair thoroughly after exposure 6 5 Seat height at the front The seat height depends on e Size of front castors e Size of front fork e Check the angle of the castor bearing house In chapter 5 there is several models of both front castors and front forks to choose between For to change the front castors or front fork unfix the wheel and place it in the required position in the front fork Angle of bearing house Correctly adjusted angle of the front fork is important to achieve proper manoeuvring qualities of the wheelchair Unfix the two screws on the inside of the frame enough to adjust the the eccentric nuts Angle the bearing house so that it is 90 relative to the ground tighten the screws with 16 Nm x 1 pc 5 mm Allen key A The bearing house can not be adjusted in height A Check the position of the anti tip 6 6 Seat height at the rear The seat height at the rear depends on e Size of main wheel e Position of main wheel Main wheel Unfix the hub bushing including washer and nut and mount it in required position in the main wheel bracket x 2 pcs 24 mm open end spanner Make sure that the nut on inside of frame totally wreathes the wheel bushing Language English Model Netti I allround Version November 2010 Readjust the brakes See chapter 6 15 A Readjust the angle of the bearin
Download Pdf Manuals
Related Search