Telephone Call Blocker T
Contents
1. Step 3 Press UP or DOWN buttons lt or gt to toggle feature ON and OFF Step 4 When ON is shown hang up handset and wait 15 seconds to exit 7 0 Changing the Pass Code The T Lock s factory default pass code is 0000 Follow steps below to change it Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 7 LCD display INPUT Step 3 Input old pass code default 0000 and press SET LCD displays N PASS Step 4 Input the new pass code up to 4 digits press SET button Step 5 Re enter new pass code and press SET to save it LCD displays SUCCEED Step 6 Hang up handset and wait 15 seconds to allow T Lock to exit programming mode Note You may use 8289 if you forget your pass code to reset back to default 0000 8 0 Browse Incoming Phone Numbers You may press the UP or DOWN buttons lt or gt to view recent incoming call records last 100 calls received The LCD will display the phone number up to 16 digits date and time of each call 9 0 Browse Outgoing Phone Numbers Press OUT to browse recent outgoing phone numbers dialed from phone s connected to the PHONE socket of the T Lock Press UP or DOWN buttons lt or gt to browse list LCD displays NO CODE when there are no calls Each record can display up to 16 digits 10 0 Removing Numbers from Lists INCOMING OUT and BLACKLIST 10 1 Removing Phone Numbers from INCOMING List To remove numbers from the INCOMING2. Telephone Call Blocker T Lock User Manual m ar a l Thank you for choosing the T Lock Call Blocker T Lock to help you eliminate unwanted phone calls Please visit TelephoneCallBlocker com to obtain the latest information on how to use and program your T Lock as well as important safety instructions and answers to frequently asked questions FAQs Installation IMPORTANT THIS DEVICE IS LINE POWERED AND DOES NOT NEED BATTERIES OR AN EXTERNAL POWER SUPPLY PLEASE IGNORE BATTERY COMPARTMENT Gonmei to phiri Cinnan to line Packing list _ Your packaging should contain the following items fo ETI VT cy 1 T Lock Call Blocker device with LCD display DO a e bese 6 buttons SET OUT BLACKLIST REMOVE UP amp DOWN lt or gt buttons a a and two RJ 11 sockets TO LINE TO PHONE ree retin ean 1 Telephone cord at ae 1 Wall Desktop bracket 1 User Manual i d o m ee f r f Jj L l i There are 2 ways of installing your T Lock as shown below The T lock should work well in both settings however we recommend that you test both to find out the best setup for you SERIES INSTALLATION PARALLEL INSTALLATION 3 TAY Splitter T Lock inet included TORPKOKE Call A Blocker FR PHOWE X YOUR PHOtwe Getting Started The T Lock is shipped from the factory ready to start working when connected to any FSK DTMF compatible phone line using the LINE socket Once ins
3. efix you wish to block Step 4 Press UP or DOWN buttons lt or gt to save LCD displays SUCCEED Repeat steps 3 4 to continue inputting number s you wish to block Step 5 When done hang up handset and wait 15 seconds to exit programming mode indicating input mode 3 1 Removing Outgoing dialing Blocked numbers from the BLACKLIST To remove a number from the blocked list you need to press SET press 3 use the UP amp DOWN buttons lt or gt to browse the list of blocked numbers you wish to remove and then press the REMOVE button to remove the number displayed LCD displays DEL and SUCCESS 4 0 Adding Incoming Phone Numbers to the BLACKLIST Follow the instructions below to add incoming phone numbers to the BLACKLIST Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 4 LCD displays the first number stored in the BLACKLIST If empty a blinking cursor should be shown as _ indicating input mode Step 3 Input phone number to be added to the incoming BLACKLIST Step 4 Press UP or DOWN buttons lt or gt to save LCD displays SUCCEED Repeat steps 2 4 to add up to 1 200 numbers up to 16 digits in length each Step 5 When done hang up handset and wait 15 seconds to exit programming mode Refer to Section 10 2 to REMOVE incoming phone numbers from BLACKLIST 5 0 Adding Incoming Area Codes or Prefixes to BLACKLIST Follow the steps below to add inc
4. egard the voice messages or any audible line errors you may hear on your telephone line 2 In input mode you may press the OUT button anytime to correct numbers 3 When removing a number the LCD may show a blinking cursor _ That s normal 4 This device uses a technology called EEPROM that allows it to retain all the programming and stored numbers even when disconnected from the phone line Warranty amp Service Hi Q Telecom Inc warrants its products to be free of defects of material and workmanship for a period of one 1 year from the date of purchase All items to be repaired under warranty are to be sent together with the original sales slip to Hi Q Telecom Inc 16562 NW 83 PL HIALEAH FL 33016 Product Support Please visit us online at http telephonecallblocker com to find the latest information on this product including frequently asked questions You may use our online contact us form to ask questions and provide feedback and or suggestions In addition our support staff is available via phone at 1 786 221 5997 Monday to Friday 11 00 am to 7 00 pm EST This manual is also available online in other languages Dutch Chinese French German Italian Spanish Russian and others Copyright Notice This document is a copyright material of Hi Q Telecom Inc and it is intended for the exclusive use of TelephoneCallBlocker com clients No one else is authorized to use copy or duplicate any part of this document with
5. list of recent calls T Lock holds up to 100 records 16 digits each simply use the UP or DOWN buttons lt or gt to browse list Then press the REMOVE button to delete number from list LCD displays DEL To remove entire list of incoming call records press the REMOVE button gently for more than 3 seconds 10 2 Removing Phone Numbers from the BLACKLIST To remove numbers from the BLACKLIST memory up to 1 200 records press the BLACKLIST button then use UP or DOWN buttons lt or gt to browse list Then press the REMOVE button to delete number from list LCD displays DEL To remove entire list press the REMOVE button more than 3 seconds NOTE You will need to input pass code default 0000 followed by the REMOVE button when LCD displays PASS This is a safety feature to prevent deleting the list unintentionally 10 3 Removing Phone Numbers from the OUT list To remove numbers from the outgoing list of recent phone numbers up to 50 records press the BLACKLIST button then use the UP or DOWN buttons lt or gt to browse list Now you can press the REMOVE button to delete any phone number you wish LCD displays SUCCEED To remove the entire list press the REMOVE button more than 3 seconds 11 0 BLACKLIST Operation T Lock will automatically disconnect off hook and hang up the call if the calling number is stored in the BLACKLIST You may hear 0 2 rings before calls are disconnected 11 1 Adding New Phone Number
6. oming phone area codes and prefixes to BLACKLIST Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off handset and press 5 If your BLACKLIST is empty a blinking cursor should be shown as Otherwise the LCD will display the first stored number in the BLACKLIST Step 3 Input the area code or prefix you wish to block example area code 305 prefix 305 558 using the dial pad on your indicating input mode telephone handset Step 4 Press UP or DOWN buttons lt or gt to save number LCD displays SAVE and SUCCEED Repeat steps 2 amp 3 to add up to 10 sets up to 10 digits in length each Step 5 When done hang up handset and wait 15 seconds to exit programming mode 5 1 Removing Incoming Area codes or Prefixes from BLACKLIST Follow steps 1 amp 2 above then follow these additional steps Step 3 Use UP or DOWN buttons lt or gt to browse list of blocked numbers Step 4 When displaying the number you wish to remove press REMOVE LCD displays DEL Step 5 When done hang up handset and wait 15 seconds to exit programming mode 6 0 Turn ON OFF feature to Block all Incoming Calls with no Caller ID Info This feature is disabled OFF as a factory default setting Please follow the steps below if you wish to turn this feature ON and block all calls with no caller ID information Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 6 LCD displays OFF
7. out written consent Violators will be prosecuted under copyright laws of the United States of America
8. s to BLACKLIST There are 2 ways of adding unwanted phone numbers to the BLACKLIST 1 When an unwanted call is ringing Simply press the BLACKLIST button while your phone is ringing before answering it to disconnect the unwanted call and add the number to the BLACKLIST 2 After answering an unwanted call You can use the scrolling UP DOWN buttons lt or gt to browse the list of recent incoming calls then press the BLACKLIST button to add unwanted phone number to list LCD displays SAVE and SUCCEED 12 0 LOCK Feature The LOCK feature is turned OFF as a factory default setting You may lift off handset and input 000111 to turn ON the LOCK feature and LOCK all functions LCD displays LOCK If your T Lock s LCD displays LOCK then lift off handset and input 123456 to turn OFF the lock function and enable all T Lock s functions 13 0 LCD Display Alerts and Messages The LCD display will show the following messages or alerts The NEW alert indicates that the phone number is new e g recently added to the T Lock s memory The REP alert indicates that the phone number is already in memory The MAIL alert indicates that you have a new voicemail this feature is provided by your phone service provider as part of the Caller ID service The LCD also shows the current date of week SUN MON TUE WED THU FRI SAT 14 0 Programming Notes 1 When using the handset to program your T Lock please disr
9. talled simply wait to start receiving calls then use the scrolling UP or DOWN buttons lt or gt to browse the list of recent incoming calls While browsing you may press the BLACKLIST button to add unwanted numbers to the BLACKLIST It s that simple IMPORTANT Please make sure your phone line has the Caller ID service Your T Lock will not work without it If you are not sure contact your telephone service provider Programming your T Lock Call Blocker PREPARATION Before you can start programming your T Lock you need to have a telephone handset wired or wireless with a dial pad connected to the PHONE socket on the back of the T Lock as shown in Series installation diagram 1 0 Setting the Year Follow these steps to change the 4th digit on the year e g from 2012 to 2013 Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 1 using the dial pad LCD displays 2012 and 3rd digit is blinking indicating that it can be changed Step 3 Press SET button again to move from the 3rd to the 4th digit of the year 2012 Step 4 Press UP button lt 4 to change the blinking digit 3 4 5 Step 5 Once the correct digit is displayed hang up handset and wait 15 seconds to exit programming mode 1 1 Setting Date amp Time If your phone service provider is FSK compatible the DATE amp TIME on your T Lock will be automatically updated when connected after the first call comes in Otherwise follo
10. w these steps to set the DATE amp TIME After setting the year s last digit in step 4 press SET again to change the Month MM use dial pad to input the correct month then press SET again to change the Day DD use dial pad to input the correct month then press SET again to change the HOUR HH use dial pad to input the correct month and then press SET again to change the Minutes MM Then hang up the handset and wait 15 seconds to exit programming mode 2 0 Setting the LCD Display Brightness Levels The factory default settings for the display brightness is 2 Follow the instructions below to change the settings Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 2 using the dial pad LCD displays LCD 2 Step 3 Press UP or DOWN buttons lt or gt to change the LCD levels from 2 to 1 2 3 4 Step 4 When done hang up handset and wait 15 seconds to exit programming mode 3 0 Adding Outgoing dialing Blocked Numbers to the BLACKLIST Follow the steps below to manually add phone numbers also prefixes or area codes that you wish to block dialing from your phone line IMPORTANT Make sure your T Lock is installed in series with your existing phone s in order for the T Lock to block all the outgoing numbers calls Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 3 LCD displays a blinking cursor Step 3 Input the phone number or area code or pr
Download Pdf Manuals
Related Search