FS-1750 FS-3750 - KYOCERA Document Solutions
Contents
1. 1 use copy modify merge or transfer copies of the Program except as provided in this license 2 reverse assemble or reverse compile the Program or 8 sublicense rent lease or assign the Program 2 Limited Warranty The Programs are provided AS IS THERE ARE NO OTHER WARRANTIES COVERING THE PROGRAMS OR CONDITIONS EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow the exclusion of implied warranties so the above exclusion may not apply to you SUPPLEMENT TO AGREEMENT FOR SOFTWARE BUNDLING AND DISTRIBUTION FOR ALDC 3 Limitation of Remedies IBM s entire liability under this license is the following 1 For any claim including fundamental breach in any form related in any way to this license IBM s liability will be for actual damages only and will be limited to the greater of a the equivalent of U S 25 000 in your local currency or b IBM s then generally available license fee for the Program This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable IBM will not be liable for any lost profits lost savings or any incidental damages or other economic consequen tial damages even if IBM or its authorized supplier has been advised of the possibility of such damages IBM will not be liable for any damages claimed by you based2. ENERGY STAR Program This function makes it possible to reduce the amount of electrical power consumed by the printer For maximum power savings turn off the printer s power supply when not using the printer for extended periods of time For details on the sleep timer function and printer power consumption refer to the instruc tion manual provided with the printer Initial settings of the sleep timer function and power saved using the sleep timer function Fe Power consumption in Initial sleep mode setting sleep mode FS 1750 30 minutes 30 minutes 14 W 30 W FS 3750 30 minutes 60 minutes 16 W 45 W ENERGY STAR program guideline The action program Energy 2000 Energy partnership for a sustainable development We get further with all our energy ENERGY Kyocera ECO PRODUCT This product has been developed and manufactured with the express interest of reducing the impact on the environment Using Kyocera s innovative cartridge free technology Kyocera has created an advanced printing system that does not require the 4 ECO wasteful replacement and disposal of a cartridge A P Q Q xii Introduction Introduction The Kyocera laser printer has many extremely desirable features It has been designed to make a contribution to a cleaner environment as well as to represent the latest generation of page printer technology Maintenance Features Compact design
3. This printer is certified in the U S to conform to the requirements of DHHS 21 CFR Sub chapter for Class I 1 laser products and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 825 1 Caution Laser radiation when open DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Introduction Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure kyocera FS 3750 kyocera FS 3750 220 240V V 50Hz 4A KYOCERA CORPORATION MADE IN JAPAN CLASS 1 LASER PRODUCT TO 1EC825 LASER KLASSE 1 NACH IEC825 KLASSE 1 LASER PRODUKT LH T 1EC825 LUOKAN 1 LASERLAITE cE 6S a oll ACNO03852444 Cor i A 220 240Vr SO 60Hz 44 CAUTION onp ere seme KYOCERA CORPORATION VORSICHT MADE IN JAPAN pod WARTUNG UND SICHERUNGS RME NETZSTECRER ZIEHEN CLASS I LASER PRODUCT TO 1EC825 ATTENTI ECECTROUES COUPER LALMENTATION D TR E REMPLACER LE FUS NU nt SE MIx DE ALIMENTACI N ANTES DEL SERVICIO Y DEARA O DEL OSIRE CAUTION PRECAUZIONE REMOVE POWER CORD BEFORE SERVICE DI ESEGUIRE RIPARA ZION o O AND FIRE REREACRUENT STACCATE IL CADO Di ALIMENTAZIONE Philippines European Asian countries CDRH regulations The Center of Devices and Radiological Health CDRH of the U S Food and Drug Admin istration implemented regulations for laser products on August 2 1976 These regulations appl
4. 64 MB Memory card slot One PC CARD PCMCIA 2 1 JEIDA 4 2 type I memory card Self test Performed at power up Scanning system Laser diode polygon mirror Maximum duty cycle 25 000 pages month 50 000 pages month Drum Amorphous silicon drum Developer Mono component dry developer Main charger Positive scorotron charger Transferring Negative charger roller Separation Curvature separation Drum cleaning Blade cleaner Drum discharging Illumination by eraser LED array Fuser Heat roller and pressure roller Toner saving Ecoprint mode Paper Plain paper See Appendix B in the User s Manual PDF file provided on the Kyocera Digital Library CD ROM Paper feed trays Cassette Legal size to A5 universal cassette 148 to 216 mm 5 13 16 to 8 1 2 x 210 to 356 mm 8 1 4 to 14 Holds 250 sheets of thickness 0 1 mm MP tray 80 to 148 mm 8 1 8 to 5 13 16 x 216 to 356 mm 8 1 2 to 14 see page B 2 in the User s Manual PDF file provided on the Kyocera Digital Library CD ROM Holds 100 sheets of thickness 0 1 mm 22 Printer Specifications Description Item FS 1750 FS 3750 Capacity ofoutput Face down tray 250 sheets of thickness 0 1 mm trays Face up tray 250 sheets of thickness 0 1 mm Ambient conditions Temperature 10 to 32 5 C 50 to 90 5 F Humidity 20 to 80 RH Optimum conditions 20 C 68 F 60 RH Altitude
5. Computer 13 9 Attach the Power Cord 13 10 Print a Status Page 14 11 Test the Interface with the Computer 14 12 Set the Emulation Mode s ssssersressrrrrrssrrrrrssrrrrrssrrrnrnsrsrnr rn 14 13 Install the Printer Driver s ssmssssssssrsrrrssrrerersrrrrrssrrrnrrsrrrnr rn 15 5 Memory Expansion Installation 18 Removing the Main Circuit Board 19 SIMM tobe used urine chloe cae 20 Installing and Removing SIMMS s ssssssessressererersrrsrrrsrnnrrssrnrrrsr 20 Testing the Expansion Memory cccccccessssseeceeesseeeeeseeenes 21 Printer Specifications ssssssnnnns 22 XVIII 1 Positioning the Printer 1 Positioning the Printer Clearance Allow at least the necessary minimum clearance around the printer see below A total space of 92 cm by 61 cm by 138 cm 36 1 4 by 24 1 16 by 54 5 16 inches is needed 30 cm 11 13 16 inches 40 cm 15 3 4 inches 20 cm 7 7 8 inches when the face up output tray is not installed Optional with the FS 1750 60cm 23 5 8 inches 25cm 9 7 8 inches Places to Avoid Avoid installing the printer in locations subject to Direct drafts of hot or cold air Direct drafts from outside Avoid locations near doors leading outside Sudden temperature or humidity changes Sources of high temperature for example near stoves or radiators Excessi
6. Max 2000m 6500 feet Illumination Max 1500 lx Power requirements 120 V 60 Hz max 5 8A 120 V 60 Hz max 7 8 A U S A Canada U S A Canada 220 to 240 V 50 60 Hz max 3 A 220 to 240 V 50 60 Hz max 4 A European countries European countries Max allowable voltage Max allowable voltage fluctuation 10 fluctuation 10 Max allowable frequency Max allowable frequency fluctuation 2 fluctuation 2 Power consumption Max 667 W Max 898 W During sleeping 14 W During sleeping 16 W Operating noise During printing LpA 50dB A During printing LpA 53 dB A in accordance with During standby LpA 39dB A Duringstandby LpA 39 dB A IS07779 Bystander During sleep mode Immeasurably low During sleep mode Immeasurably low Position sound pressure level at the front Dimensions 373 mm 14 11 16 wide x 310 mm 12 3 16 high x 383 mm 15 1 16 deep Excl the paper tray Weight 14 kg 30 1b main unit only 23 ce KYOCERA Printed in Japan Imprim au Japon 5KKT1750E AX 1199PS SG
7. container is prop erly locked in the printer 3 Close the Top Cover Close the top cover by pressing the arrowed part in this figure 4 Install the Waste Toner Bottle The waste toner bottle is in the toner kit supplied with the printer The waste toner bottle must be installed in the printer Install the waste toner bottle in the printer as follows 1 Take the waste toner bottle from the toner kit supplied Donotcap the waste toner bottle Waste Toner Bottle 4 Setting Up and Interfacing 2 Open the side cover on the left side of the Side Cover printer 3 Insert the waste toner bottle with the bottle tilted slightly towards you as shown in the figure 4 Ensuring thatitis correctly inserted close the side cover 4 Setting Up and Interfacing 5 Adjusting the Paper Guides in the Cassette and Adding Paper The paper cassette provided with the printer can accommodate paper sizes from A5 to legal by adjusting the position of the paper guides and the paper stopper Paper sizes that are not standard sizes custom sizes but within the size limitations can also be loaded into the cas sette When loading custom sizes into the cassette the size must be input into the printer on the control panel Refer to 2 7 Setting Custom Sizes in the User s Manual PDF file pro vided on the Kyocera Digital Library CD ROM Standard size paper settings are indicated as fixed positions in the
8. on any third party claim This limitation of remedies also applies to any developer of Programs supplied to IBM IBM s and the developer s limitations of remedies are not cumulative Such developer is an intended beneficiary of this Section Some jurisdictions do not allow these limitations or exclusions so they may not apply to you 4 General You may terminate your license at any time IBM may terminate your license if you fail to comply with the terms and conditions of this license In either event you must destroy all your copies of the Program You are respon sible for payment of any taxes including personal property taxes resulting from this license Neither party may bring an action regardless of form more than two years after the cause of action arose If you acquired the Pro gram in the United States this license is governed by the laws of the State of New York If you acquired the Program in Canada this license is governed by the laws of the Province of Ontario Otherwise this license is governed by the laws of the country in which you acquired the Program ii Introduction Typeface Trademark Acknowledgement All resident fonts in this printer are licensed from Agfa Corporation Helvetica Palatino and Times are registered trademarks of Linotype Hell AG ITC Avant Garde Gothic ITC Bookman ITC ZapfChancery and ITC Zapf Dingbats are registered trademarks of International Typeface Corporation Agfa Japan License Agreemen
9. they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product Except as explained elsewhere in User s Manual do not attempt to service this product yourself Removing covers may expose you to dangerous voltage points or other risks Refer all servicing in those compartments to service personnel Unplug this product from the wall outlet and refer servicing to qualified service per sonnel under the following conditions A When the power cord or plug is damaged or frayed B If liquid has been spilled into the product C If the product has been exposed to rain or water D Ifthe product does not operate normally when the operating instructions are fol lowed Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E Ifthe product has been dropped or the cabinet has been damaged vii Introduction Declaration of Conformity U S A Model Number Page Printer FS 1750 FS 3750 as tested with enhancement optional units EF 1 PF 21 DU 21 HS 21 and ST 20 etc Trade Name Kyocera Responsible Party Kyocera Electronics Inc Address 11465 John s Creek Parkway Suite 250 Duluth GA 30097 U S A Telephone number 770 623 2150 Fax numbe
10. BE is a registered trademark of Kyocera Corporation PRESCRIBE 2e KPDL and KIR Kyocera Image Refinement are trademarks of Kyocera Corporation Diablo 630 is a product of Xerox Corporation IBM Proprinter X24E is a product of International Business Machines Corporation Epson LQ 850 is a product of Seiko Epson Corporation Hewlett Packard PCL and PJL are registered trademarks of Hewlett Packard Company Centronics is a trade name of Centronics Data Computer Corp PostScript is a registered trademark of Adobe Systems Incorporated Macintosh is a registered trademark of Apple computer Inc AppleTalk is a trademark of Apple Computer Inc Microsoft Windows and MS DOS are registered trademarks of Microsoft Corporation PowerPC is a trademark of International Business Machines Corporation ENERGY STAR is a U S registered mark This Kyocera page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL6 language emulation PeerlessPrintXL is a trademark of The Peerless Group Redondo Beach CA 90278 U S A This product was developed using the Tornado Real Time Operating System and Tools from Wind River Sys tems Contains UFST and MicroType from Agfa Corporation KIR uses Pixel Magic s resolution enhancement technology Magic Pixel Magic is a trademark of Oak Technology Inc 1999 by Kyocera Corporation All rights reserved Revision 1 0 October 1999 Introduction IBM PROGRAM LICENSE AGREEMENT THE DEVICE
11. Cy KYOCERA FS 1750 FSS7E0 Installation Manual Kyocera Laser Printer Introduction Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER S EMULATION MODE The printer is factory set to emulate the PCL 6 The emulation mode can be changed by following the procedures described in Chapter 2 in the User s Manual PDF file provided on the Kyocera Digital Library CD ROM Notice The information in this manual is subject to change without notification Additional pages may be inserted in future editions The user is asked to excuse any technical inaccuracies or typographical errors in the present edition No responsibility is assumed if accidents occur while the user is following the instructions in this manual No responsibility is assumed for defects in the printer s firmware contents of its read only memory This manual any copyrightable subject matter sold or provided with or in connection with the sale of the page printer are protected by copyright All rights are reserved Copying or other reproduction of all or part of this manual any copyrightable subject matter without the prior written consent of Kyocera Corporation is prohib ited Any copies made of all or part of this manual any copyrightable subject must contain the same copyright notice as the material from which the copying is done Regarding Tradenames PRESCRI
12. Thanks tothe inboard cassette configuration the printer requires no more space than the average computer Ultra long life modules The main modules in this laser printer such as the drum developer unit and fuser unit have been designed for ultra long life Amorphous silicon drum The drum has been developed using Kyocera s unique ceramic technology using amor phous silicon Print Engine Features Superb print quality Using 1200 dots per inch in Fast 1200 mode or Fine 1200 mode the printout is close to typeset quality Also with Kyocera Image Refinement KIR technology high quality printing can be achieved even at 600 dpi and 300 dpi High speed A4 sizes typically print at the rate of 18 14 for the FS 1750 pages per minute Actual time varies according to page complexity Large paper capacity Approximately 250 sheets can be loaded into the paper cassette and about 100 sheets can be loaded into the MP tray Wide variety of print media As well as standard paper the printer will print on Transparency labels and other types of special purpose media Sleep mode Conserves energy during the printer s idle periods Ecoprint mode Extends the toner yield by reducing the amount of toner used on the page Standard bi directional parallel interface Supports high speed data exchange with the computer xiii Introduction Software Features Wide variety of available fonts The printer comes with 80 PCL PS compatible font
13. YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS PRO GRAMS WHICH BELONG TO INTERNATIONAL BUSINESS MACHINES CORPORATION IBM THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM IF YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS LICENSE THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY RETURN THE DEVICE FOR A FULL REFUND IF YOU DO NOT SO RETURN THE DEVICE WITHIN THE 14 DAYS THEN YOU WILL BE ASSUMED TO HAVE AGREED TO THESE TERMS AND CONDITIONS The Programs are licensed not sold IBM or the applicable IBM country organization grants you a license for the Programs only in the country where you acquired the Programs You obtain no rights other than those granted you under this license The term Programs means the original and all whole or partial copies of it including modified copies or por tions merged into other programs IBM retains title to the Programs IBM owns or has licensed from the owner copyrights in the Programs 1 License Under this license you may use the Programs only with the device on which they are installed and transfer pos session of the Programs and the device to another party If you transfer the Programs you must transfer a copy of this license and any other documentation to the other party Your license is then terminated The other party agrees to these terms and conditions by its first use of the Program You may not
14. ase or otherwise transfer the Software and or Typefaces without the prior written consent of Agfa Japan Use duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Techni cal Data and Computer Software clause at FAR 252 227 7013 subdivision b 3 ii or subparagraph c 1 ii as appropriate Further use duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52 227 19 c 2 YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT UNDERSTAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS NEITHER PARTY SHALL BE BOUND BY ANY STATEMENT OR REPRESENTATION NOT CONTAINED IN THIS AGREEMENT NO CHANGE IN THIS AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY PROPERLY AUTHORIZED REPRE SENTATIVES OF EACH PARTY BY OPENING THIS DISKETTE PACKAGE YOU AGREE TO ACCEPT THE TERMS AND CONDITIONS OF THIS AGREEMENT iii Introduction FCC statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired opera tion Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reason able protection against harmful interferen
15. cable specifications Technical drawings Descriptions of the procedures that guarantee the conformity Other technical information KYOCERA ELECTRONICS EUROPE GmbH Mollsfeld 12 40670 Meerbusch Germany Phone 49 21599180 Fax 49 21 59 918 100 Declaration of Conformity Australia Manufacturer s name Kyocera Corporation Printer Division Manufacturer s address 2 14 9 Tamagawadai Setagaya Ward Tokyo 158 8610 Japan declares that the product Product name Page Printer Model number FS 1750 FS 3750 as tested with enhancement optional units EF 1 PF 21 DU 21 HS 21 and ST 20 etc Description of device This Page Printer Model FS 3750 is the 18ppm FS 1750 is the 14ppm A4 size and utilized plane paper laser dry toner etc The printer can be equipped with several enhancement optional units as a paper feeder as PF 21 a duplexer as DU 21 a sorter as ST 20 etc Conforms to the following product specifications AS NZS 3548 1995 EN 55 022 1994 Class B if operated without PF 7E and without HS 3E EN 55 022 1994 Class ifoperated with PF 7E and with HS 3E IEC60950 EN 60 950 1992 A1 A2 A3 A4 IEC60825 1 EN 60 825 1 1994 A11 The manufacturer and its merchandising companies retain the following technical docu mentation in anticipation of the inspection that may be conducted by the authorities con cerned User s instruction that conforms to the applicable specifications Technical drawings Descriptions of the p
16. cassette Before adding paper remove the paper cassette all the way from the printer Read the paper manufacturer s instructions concerning handling of the paper 1 Remove the paper cassette from the printer a and place it on a flat stable surface L Paper Cassette 2 Push the bottom plate down until it locks Bottom Plate 3 Turn the paper size dial so that the size of Paper Size Dial the paper you are going to use appearsin the paper size window Whenthe paper size dial is setto CUSTOM the paper size must be set into the printer on the control panel See 2 7 Setting Custom Sizes for the setting procedure in the User s Manual PDF file provided on the Kyocera Digital Library CD ROM 4 Adjust the paper guide and paper stopper positions Move the paper guides while lifting the green latch on the right Set the triangular markings on the guides to the size of paper that you are to use as indicated Triangle Mark Paper Guide 10 4 Setting Up and Interfacing Move the paper stopper while pushing on the green button at the back Set the paper Paper Stopper stopper to the size of paper that you are to use as indicated in the small windows on the floor of the cassette When using custom size paper move the paper guides and paper stopper all the way out insert the paper and then adjust the paper guides and paper stopper to suit Adjust them so that they are in light contact with the
17. ce in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communica tions However there is no guarantee that interference will not occur in a particular instal lation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures O Reorient or relocate the receiving antenna O Increase the separation between the equipment and receiver O Connect the equipment into an outlet on a circuit different from that to which the receiver is connected O Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the manufacturer for compliance could void the user s authority to operate the equipment Shielded circular cable should be used for interfacing with the computer Caution to user Any modification without prior permission may cause harmful interference If any modification change is introduced to this equipment without prior permission Kyo cera as the manufacturer cannot guarantee compliance with FCC rules To use equipment which does not comply with FCC rules is prohibited The printer may be optionally installed with the following units Con
18. d on the right side of the printer doubles as the memory card slot Be sure to remove the memory card first if inserted before lifting or moving the printer 3 Names of Parts 3 Names of Parts This section takes you on a guided tour ofthe printer pointing out its major parts The part names introduced here will be used throughout this manual Symbols appearing with the part names have the following meanings UT See page XX in this manual See Chapter or Appendix XX in the User s Manual PDF file provided on the Kyo cera Digital Library CD ROM Front View Face down Paper Stopper Output Tray EU 12 h a Control Panel apter Paper Full Sensor Chapter 2 Model FS 3750 only MP Multi Purpose Tray Chapter 1 Side Cover Paper Feed Unit UUP 9 Release Lever Chapter 1 4 Chapter 4 Power Switch Paper Cassette a Up 10 Paper Size Window Chapter 1 LUP 10 Transfer Roller Registration Rolloer Chapter 4 Option Paper Feeder Connector Paper Feed Unit Memory Card Slot Chapter 4 Chapter 1 2 3 Names of Parts Interior View Toner Container Release Lever Green Toner Container Side Cover CU P 7 CU P 9 Chapter 1 Chapter 1 4 Cleaner Knob Green Waste Toner Bottle Chapter 4 pe Main Charger Unit Chapter 4 Chapter 4 Rear View Rear Cover Serial Interface RS 232C RS 422A Connector COP 13 Appendix C Parallel Interface Connector Powe
19. des Druckers einge baut ist muB eine leicht zug ngliche Steckdose in der Nahe des Ger tes vorhanden sein Wenn der Drucker mit dem gesonderten Sorter SO 6 oder Stapler ST 20 ver wendet wird mu darauf geachtet werden da diese Ger te einwandfrei an separate Steckdosen angeschlossen sind um Kurzschlu zu vermeiden 2 Unpacking and Inspection The printer is packed as shown below Unpack the printer following figures 1 and 2 on the next page While unpacking it check that the listed parts are all accounted for Examine the package for any signs of damage that may have been caused during transpor tation Ifthe carton is found to be badly damaged leave the carton unopened and immedi ately notify the dealer from whom you purchased the printer Save the box and other packing materials in case you have to repack the printer for trans portation at a later date 2 Unpacking and Inspection List of Shipped Components QO A Face up Output Tray FS 3750 only B Toner Kit Box for the Developer Unit C Power Cord D Installation Manual and Kyocera Digital Library CD ROM including the printer drivers and manuals E Paper Stopper FS 3750 only I I I QO Printer To remove the printer from the box grasp the handholds on either side of the printer Lift the printer from the carton as shown below Always use these handholds whenever you lift or move the printer The handhol
20. emove the three screws from the printer s rear cover 3 Pull the main circuit board all the way out of the printer Before pulling the main board out clean an area on the table etc at the back of the printer s rear panel Foreign objects acci dentally sticking to the back of the main board can cause serious damage to the printer Install the SIMM as described on the next page 19 5 Memory Expansion Installation SIMM to be used See your Kyocera dealer for purchasing information of the SIMMs that are best suited for use with this printer Either 4 MB 8 MB 16 MB or 32 MB SIMMs can be used for memory expansion Installing and Removing SIMMs Installing SIMMs Insert the SIMM into the socket as shown right 1 Remove the SIMM from its package 2 Insert the connector end of the SIMM into the socket 3 Carefully push the board upright until it snaps into place Make sure that the catches at the ends of the socket fit into the holes at the ends of the SIMM board Removing SIMMs To remove a SIMM carefully pull the end catches slightly outwards and tilt the SIMM as shown then pull the SIMM out of the socket Reverse the procedure under Withdrawing the Main Circuit Board from the Printer to put the main circuit board back into the printer 20 5 Memory Expansion Installation Testing the Expansion Memory After you have finished installing SIMMs in the printer test the printer to see
21. esolution Printing condition 1200 dpi 300 dpi 600 dpi Fast mode Fine mode PCL 6 duplex mode None 8MB 8MB 8 MB 8 MB PCL 6 duplex mode On 8 MB 8MB 8 MB 12 MB KPDL duplex mode None 8MB 8 MB 8 MB 8 MB KPDL duplex mode On 8 MB 8 MB 12 MB 12 MB PCL 6 KPDL resource protection duplex mode None PCL 6 KPDL resource protection duplex mode On 10 MB 10 MB 10 MB 14 MB 14 MB 14 MB 5 Memory Expansion Installation Removing the Main Circuit Board The main circuit board of the printer is equipped with two sockets for memory expansion Expansion memory is available in the form of a SIMM The following instructions are intended for the technician only Notes on Handling the Main Circuit Board and SIMM Protect the electronics by taking these precautions O Before touching the main circuit board touch a water pipe or other large metal object to dis charge yourself of static electricity While doing the work it is recommended that you wear an antistatic wrist strap O Touch the main circuit board and SIMM only by the edges Withdrawing the Main Circuit Board from the Printer Be sure to remove the memory card first if inserted in the printer s memory card slot Withdraw the main circuit board completely from the printer as follows 1 Turn the printer s power off Unplug the printer s power cable and disconnect the printer from the host computer 2 R
22. forming to the Class A limits O HS 3E Bulk Paper Stacker for FS 3750 O PF 7E Bulk Paper Feeder IV Introduction Conforming to the Class B limits EF 1 Envelope Feeder DU 20 Duplexer for FS 3750 DU 21 Duplexer for FS 1750 FS 3750 HS 20 Paper Handler Stacker for FS 3750 HS 21 Paper Handler Stacker for FS 1750 FS 3750 PF 20 PF 20mini Paper Feeder for FS 3750 PF 21 PF 21mini Paper Feeder for FS 1750 FS 3750 SO 6 Sorter Stacker ST 20 Bulk Paper Stacker 0000000000 Interface connectors Important note on the interface connectors Be sure to turn off printer power before connecting or disconnecting an interface cable to the printer For protection against static discharge which may be applied to the printer s inter nalelectronics through the interface connector s keep any interface connector which is not in use capped using the protective cap supplied Use shielded interface cable Safety information Laser safety This printer is certified as a Class 1 laser product under the U S Department of Health and Human Services DHHS Radiation Performance Standard according to Radiation Control for Health and Safety Act of 1968 This means that the printer does not produce hazardous laser radiation Since radiation emitted inside the printer is completely confined within protective housings and external covers the laser beam cannot escape from the printer dur ing any phase of user operation Laser notice
23. if the instal lation has been successful To test the expansion memory proceed as follows 1 Make sure the power switch is off Plug the power cord into the printer and turn power on 2 When the printer is on line press the STATUS key 3 Iftheinstallation has been successful the amount of memory shown on the status page in the User s Manual PDF file provided on the Kyocera Digital Library CD ROM will correspond with the amount of expanded memory The factory installed memory size is 8 MB for the FS 1750 and 16 MB for the FS 3750 21 Printer Specifications Printer Specifications depends on input data Description Item FS 1750 FS 3750 Printing method Electrophotography laser scan Printing speed 14 pages minute A4 or letter size 18 pages minute A4 or letter size paper when printing multiple copies paper when printing multiple copies of the same page of the same page Resolution 1200 dpi Fine 1200 mode Fast 1200 mode 600 dpi with KIR Kyocera Image Refinement 300 dpi with KIR Kyocera Image Refinement First print Approx 15 seconds A4 or letter size Approx 12 seconds A4 or letter size depends on input data Warm up time Approx 50 seconds at 23 C 120 or 220 V Approx 40 seconds at 23 C 120 or 220 V Controller PowerPC 603e 100 MHz PowerPC 603e 166 MHz Main memory 8 MB expandable up to 72 MB 16 MB expandable up to
24. ing options are available for the printer Printer Printer 1 DU 20 Duplexer for FS 3750 DU 21 Duplexer for FS 1750 FS 3750 Performs duplex printing Attaches to the bot tom of the printer 2 EF 1 Envelope feeder Allows continuous feeding of envelopes and postcards Can be installed by removing the MP tray from the printer 3 HS 20 Paper handler stacker for FS 3750 HS 21 Paper handler stacker for FS 1750 FS 3750 Required in order to use the printer with the DU 20 DU 21 duplexer the SO 6 sorter stacker or the ST 20 stacker XV Introduction HS 3E Bulk paper stacker for FS 3750 Large capacity stacker that holds up to approximately 2 000 sheets of paper Attaches to the rear of the printer PA 1 PA 20 Paper path adaptor Necessary when optional feeders sorters and duplex units are attached to the printer The point of attachment varies depending on the option installed PF 20 PF 20mini Paper feeder for FS 3750 PF 21 PF 21mini Paper feeder for FS 1750 FS 3750 Holds approximately 500 sheets of paper Up to two paper feeders can be attached to the bot tom of the printer unit However the PF 20mini PF 21mini cannot be used together with options such as duplexers or sorters PF 7E Bulk paper feeder Holds up to about 2 000 sheets of paper Can be installed by removing the MP tray from the printer PT 4 Face up output t
25. is installed click on Close to close Control Panel 17 5 Memory Expansion Installation 5 Memory Expansion Installation In this section is explained how to expand the printer s memory Expanded printer memory enables you to print more complex pages download more fonts and define more macros It begins by explaining how to remove the main circuit board from the printer and explains how to install a SIMM single in line memory module on the main circuit board The FS 1750 comes supplied with 8 MB of memory installed and likewise the FS 3750 comes with 16 MB of memory supplied Two slots are provided for expanding the memory in your printer so that more complex printing can be done as well as increasing the printing speed By installing optional memory cards into your printer the memory in the FS 1750 can be increased to a maximum of 72 MB and the FS 3750 can be increased to a maximum of 64 MB A 16 MB SIMM is installed in one of the SIMM sockets in the FS 3750 so in order to increase the memory to the maximum 64 MB this SIMM must be changed The expansion memory should be installed only by a Kyocera authorized dealer or Kyocera certified technician Kyocera shall not be liable for damage due to improper installation of the expansion memory The minimum memory requirements for the printer with various options installed are listed in the table below Please refer to this table when expanding the printer s memory R
26. is off Ds 2 Plug one end of the power cord into the Power Cord receptacle at the back ofthe printer 3 Plug the other end into the wall outlet Power Cord Receptacle 13 4 Setting Up and Interfacing 10 Print a Status Page Test that the printer works by printing out a status page as follows 1 Switch on the printer s power The message display should indicate When the printer is first switched on after installation there will be a delay of several minutes are nee 6 to 7 minutes Botore the printer oe ready to print During this 2 Wait until the ON LINE indicator is also lit and the message display indicates F 3 Press the STATUS key The printer should print a page listing the positions of margins memory allocation and other information Asample status printout is shown in Chapter 2 in the User s Manual PDF file provided on the Kyocera Digital Library CD ROM 11 Test the Interface with the Computer Test that the printer and computer are correctly connected If you have connected the printer and computer with a parallel interface cable follow the procedure below i4 and that the ON LINE 1 Check that the printer s message display indicates Fix indicator is ON 2 Boot the computer in DOS mode or set the computer to DOS prompt mode 3 At the DOS prompt type the following ECHO R STAT EXIT gt PRN If the printer prints a status page the computer and printer are c
27. mp Start Menu FR Settings 4 x Control Panel l Folder Options AlActive Desktop 2 Fed CESSE GES Windows Update 2 Help A Taskbar HS Start button R Shut Down Aseri 1 A1 Y Windows 95 Windows 98 3 The printer folder will open Double click on Add printer CR TE 2 File Edit View Help File Edt View Go Favorites Help e XX B Cut Copy Address a Printers Add Printer Back Forward Up Printers Windows 95 Windows 98 4 The Printer Wizard screen will appear Click on Next gt 5 Ascreen for selecting the printer to be connected will appear Select the most appropri ate printer and click on Next 6 Next Click the manufacturer and model of your printer screen will appear At this point select Have Disk located at the lower right See the figure for Step 7 7 Ascreen for installing from floppy disk will appear Copy manufacture s files from inside the box or input one of the following directories Standard PCL5E driver CD ROM Drive Name drivers Language pcl 9x Standard PCLXL driver CD ROM Drive Name drivers Language pcl 9x enhanced 16 Cm 4 Setting Up and Interfacing Standard KPDL driver CD ROM Drive Name drivers Language kpdl 9x Add Printer Wizard SZ Click the manufacturer and model of your printer If your printer came with an CA installation disk click Have Disk If your printer is
28. not listed consult your printer documentation for a compatible printer Manufacturers Printers Insert the manufacturer s installation disk into the drive selected and then click OK Cancel Copy manufacturer s files from Have Dick CD ROM Drive Name x Browse lt Back Next gt Cancel Select Kyocera FS 1750 or Kyocera FS 3750 click on Next gt and follow the on screen instructions to install Once the driver has been properly installed a Kyocera printer icon will be added to the printers folder When printing under Windows 95 98 be sure to set the emulation of this printer to PCL 6 default setting Windows 3 1 To install the printer driver for Windows 3 1 proceed as follows 1 LJ 2 3 Insert the Kyocera Digital Library CD ROM in your CD ROM drive Start Windows on your computer Double click on Control Panel Double click on Printers Click on Add Click on Install Select Install Unlisted or Updated Printer under List of Printers Click Install Select the drive into which you inserted the Kyocera Digital Library CD ROM and then select one of the following directories Standard PCL5E driver CD ROM Drive Name drivers Language pcl 3x Standard PCLXL driver CD ROM Drive Name drivers Language pcl 3x enhanced Standard KPDL driver CD ROM Drive Name drivers Language kpd1 3x Click OK and follow the instructions that appear on the screen 10 When the driver
29. nserted into the computer if the computer is set for CD auto run Proceed with the installation according to the instructions that appear on the screen Read the explanation below for information about the main screens during installation The screens shown below are typ ical examples Specific screen content may vary slightly according to the version of the Kyo cera Digital Library CD ROM being used Select FS 3750 or FS 1750 from this screen Select a Kyocera printer model KYOCE Ra Select your Kyocera model Once selected click Next Available models High performance laser printer The types of drivers are shown below Select the driver that you need When you click an explanation appears below the box Select a driver type KYOCE Ra T the driver type you wish to use with this printer and click Available drivers Kyocera FS 3750 XL Kyocera FS 3750 KPDL 2 Version 3 170 English Bock en Depending on the computer installation screens may not appear If this happens install the printer driver according to the procedure below 15 4 Setting Up and Interfacing 1 Insert the supplied CD ROM Kyocera Digital Library into the CD ROM drive of the computer 2 Click on Start with the mouse on the Windows95 98 Task Bar and align the cursor with Settings Click on Printers among the items displayed Control Panel fal Programs z EDER 3 Documents ls Taskbar a
30. ntil the last use of the Software and Typefaces unless sooner terminated This License may be terminated by Agfa Japan if you fail to comply with the terms of this License and such failure is not remedied within thirty 30 days after notice from Agfa Japan When this License expires or is termi nated you shall either return to Agfa Japan or destroy all copies of the Software and Typefaces and documen tation as requested You agree that you will not modify alter disassemble decrypt reverse engineer or decompile the Software Agfa Japan warrants that for ninety 90 days after delivery the Software will perform in accordance with Agfa Japan published specifications and the diskette will be free from defects in material and workmanship Agfa Japan does not warrant that the Software is free from all bugs errors and omissions THE PARTIES AGREE THAT ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE EXCLUDED Your exclusive remedy and the sole liability of Agfa Japan in connection with the Software and Typefaces is repair or replacement of defective parts upon their return to Agfa Japan IN NO EVENT WILL AGFA JAPAN BE LIABLE FOR LOST PROFITS LOST DATA OR ANY OTHER INCI DENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES CAUSED BY ABUSE OR MISAPPLICA TION OF THE SOFTWARE AND TYPEFACES New York U S A law governs this Agreement You shall not sublicense sell le
31. onnected correctly For details on the status page refer to Chapter 2 in the User s Manual PDF file provided on the Kyocera Digital Library CD ROM If you do not get this result check that the cable is securely plugged in at both ends and repeat the test Ifyou still do not get the right result you may have a defective or improperly wired cable Try using a different cable 12 Set the Emulation Mode The printer emulates the operation of five other printers Itis factory set to emulate the PCL 6 at power up If you primarily use software that supports PCL 6 or that supports the Kyocera printer itself the factory setting is the one you want If you primarily use software that sup ports another printer it is convenient to change the printer s power up emulation mode The emulation mode can be changed from the printer control panel To change the emula tion mode refer to the Mode Select Menu diagram on the last page of the User s Manual PDF file provided on the Kyocera Digital Library CD ROM 14 4 Setting Up and Interfacing 13 Install the Printer Driver Printer drivers are provided for using the printer with Windows 95 Windows 98 or Windows 3 1 Use the Kyocera Digital Library CD ROM supplied with the printer To install the printer driver proceed as follows Reference to the Windows manual is also rec ommended Windows 95 Windows 98 The automatic installation screen appears when the CD ROM for the printer is i
32. paper Tap the edges of the paper to align the sheets When loading the paper Limitation neatly Set the paper in the cassette as make sure the leading mark edge of paper is not bent shown The side of paper that faces down any way ward in the cassette is the one on which printing is done Do not load paper into the cassette higher than the limitation mark on the right The cassette should hold approximately 250 sheets of paper with a 0 1 mm thickness Set the stack of paper so that it is under the clips as shown Hold the cassette as shown in the illustra tion and insert the paper cassette into the printer cassette slot Push it straight in as far as it will go If the paper size dial on the cassette is not set to match the size of paper inserted a paper jam may result 11 4 Setting Up and Interfacing 6 Open the Paper Stopper on the Face down Output Tray Open the paper stopper as shown right Paper Stopper 7 Install the Face up Output Tray This face up output tray is a separate option PT 4 with the FS 1750 If you want the printed pages stacked face up in reverse order mount the face up output tray as follows Depending on the size of the paper you use mount the paper stopper on the face up output tray as shown below Legal Size A4 Size Letter Size 12 4 Setting Up and Interfacing 8 Connect the Printer to the Computer The printe
33. r 770 623 2151 Contact person for technical matter Paul Bosak Phone 770 623 2163 Manufacturer s name Kyocera Corporation Printer Division Manufacturer s address 2 14 9 Tamagawadai Setagaya Ward Tokyo 158 8610 Japan This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Marking Directive according to Council Directive 89 336 EEC and 73 23 EEC Manufacturer s name Kyocera Corporation Printer Division Manufacturer s address 2 14 9 Tamagawadai Setagaya Ward Tokyo 158 8610 Japan declares that the product Product name Page Printer Model number FS 1750 FS 3750 as tested with enhancement optional units EF 1 PF 21 DU 21 HS 21 and ST 20 etc conforms to the following product specifications EN 55 022 1998 Class B if operated without PF 7E and without HS 3E EN 55 022 1998 Class A if operated with PF 7E and with HS 3E EN 61 000 3 2 1995 EN 50 082 1 1992 IEC 801 2 1991 IEC 801 3 1984 IEC 801 4 1988 EN 60 950 1992 A1 A2 A3 A4 EN 60 825 1 A11 1994 vill Introduction The manufacturer and its merchandising companies retain the following technical docu mentation in anticipation of the inspection that may be conducted by the authorities con cerned User s instruction that conforms to the appli
34. r Cord Receptacle COP 13 Appendix C LP 18 Option ieee Chapter 1 Handler Stacker Option Interface Slot Cover Connector CU p 13 Appendix C To protect the printer against static discharge the connector must be covered with the supplied pro tective cap when not in use 4 Setting Up and Interfacing 4 Setting Up and Interfacing Before you can use the printer for the first time you must set up the printer by installing the printer components and interfacing with the computer Follow the steps that follow 1 Open the Top Cover 1 Remove the packing tape from the printer 2 Open the printer top cover all the way 2 Install the Toner Container 1 Take the toner container from the toner kit 2 With the label side down thoroughly shake the toner container in the direction of the arrow ten times or more to loosen and mix the toner inside 3 The bottom of the toner container is sealed with a sealing strip Peel off the seal on the toner container and carefully pull off and dispose of the sealing strip Be sure to peel the seal off the toner con tainer before the toner container is fitted into the developer unit 4 Install the toner container on the developer as show in the figure 7 4 Setting Up and Interfacing 5 When the toner container is installed cor rectly on the developer push the top of the container unit PUSH HERE until it locks in Make sure that the toner
35. r has two computer cable connectors and a slot for installing an option interface The one marked B is for a parallel Centronics standard interface The one marked IOIOI is for a serial RS 232C RS 422A interface You may use whichever is convenient for your computer with the option interface if you have already have one installed All interface connectors can be used simultaneously with different computers Serial RS 232C RS 422A Interface Connector Parallel Interface Connector Option Interface Slot Cover Only connect or disconnect cables to the connectors while the printer and computer power are switched off Parallel interface Plug one end of the cable into the connector marked Parallel on the printer Close theclipson Rear Panel both sides to hold it in place Plug the other end into a parallel Centronics interface connector on your computer This con nector is usually marked PRINTER Printer Cable For more details about the parallel interface see Appendix C in the User s Manual PDF file pro vided on the Kyocera Digital Library CD ROM Serial interface The serial interface of this printer is set to RS 232C mode before leaving the factory but can also be set to RS 422A mode to suit your operating environment Follow the instructions in Appendix Cin the User s Manual PDF file provided on the Kyocera Digital Library CD ROM 9 Attach the Power Cord 1 Check that the power switch
36. ray for FS 1750 This is a face up output tray It attaches to the rear of the printer SO 6 Sorter stacker A sorter stacker providing 15 sorter trays and 1 bulk tray Attaches to the bottom of the printer 10 ST 20 Bulk paper stacker Large capacity stacker that holds up to approximately 1 500 sheets of paper Attaches to the bottom of the printer XVI Introduction Guide to the Manual Unless specifically stated otherwise information in this manual applies to printer models FS 1750 FS 3750 The printer illustrations used in this manual are of the FS 3750 Installation Manual This booklet The Installation Manual is this booklet This manual guides you through the following topics O Installation O Printer operation CD ROM Kyocera Digital Library The CD ROM supplied contains the printer User s Manual PRESCRIBE 2e Programming Manual and PDF417 Two Dimensional Bar Code Implementation Manual To gain access to these documents insert the CD ROM into the appropriate drive and follow the instruc tions on the insert accompanying the CD ROM To view these documents you need the Adobe Acrobat software installed in your computer For details read the instructions on the CD ROM package The User s Manual guides you through topics concerning the operations and maintenance of the printer User s Manual on CD ROM O Installation O Printer operation Control panel operations O Font
37. rocedures that guarantee the conformity Other technical information Introduction The manufacturer has been employed with ISO9001 scheme The manufacturer has been attested by JQA and BS KYOCERA ELECTRONICS AUSTRALIA PTY LTD Unit 6 112 Talavera Road North Ryde NSW 2113 Australia Phone 61 2 9888 9999 Fax 61 2 9888 9588 Canadian Department of Communications compliance statement This Class B digital apparatus complies with Canadian ICES 003 Avis de conformit aux normes du minist re des Communications du Canada Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada ISO 7779 Maschinenlarminformationsverordnung 3 GSGV 18 01 1991 Der h chste Schalldruck pegel betr gt 70 dB A oder weniger gem ISO 7779 Disclaimer We shall have no liability or responsibility to customers or any other person or entity with respect to any liability loss or damage caused or alleged to be caused directly or indirectly by equipment sold or furnished by us including but not limited to any interruption of ser vice loss of business or anticipatory profits or consequential damages resulting from the use or operation of the equipment or software Introduction Prolonged Non Use and Moving the Printer Prolonged Non use If you ever leave the printer unused for a long period of time remove the power cord from the wall outlet We recommend you consult with your dealer about the additional action
38. s g Well ventilated not too hot or cold and not too damp or dry Temperature 10 to 32 5 C 50 to 90 5 F Humidity 20 to 80 If you install the printer where the temperature or humidity is outside the above ranges you may not get the best print quality and there will be an increased chance of paper jams 2 Unpacking and Inspection Power Supply The printer should not be on the same power circuit as an air conditioner fluorescent light copier or shredder because these devices generate electrical noise on the power line If it must share a power circuit with equipment like this a high frequency noise filter or isola tion transformer is advisable Filters and transformers are available commercially Avoid using plug multipliers to connect a large number of devices on the same circuit as the printer Ifthe power from the outlet itself appears to be unstable a line stabilizer should be used In places where the voltage tends to fluctuate it may be necessary to install a voltage regulator As the disconnect device is not incorporated in the printer s AC primary cir cuit an easily accessible socket outlet must be provided near the equipment Ifthe printer is used with the optional Sorter SO 6 or Stacker ST 20 in order to avoid short circuiting it should be ensured that these devices are plugged securely into their respective power outlets Da kein Trennschalter in den Wechselstrom Prim rkreis
39. s O Maintenance and troubleshooting PRESCRIBE 2e Programming Manual on CD ROM O PRESCRIBE 2e command reference O Fonts O Bar codes O Printer permanent parameters O Emulation PDF417 Two Dimensional Bar Code Implementation Manual on CD ROM O PDF417 overview O PRESCRIBE 2e commands for PDF417 XVII Table of Contents Table of Contents 1 Positioning the Printer 1 Clearance Gaee eeni 1 Places to AYold sas sscsstoreststs rsesset aain ii i iae 1 Basic requirements 2 Power SUPPLY accenda niea i ie E EKRAR ek tenue 3 2 Unpacking and Inspection 3 List of Shipped Components 4 3 Names Of Pal tS s sssisssssvons nn snssnssesnenensnnbsnnss sessarernsnnen 5 Front Views dee ids tes invest dented cease el teases enter sheets 5 Interior View ba nr Mis onto Gand FANA R aa sr stR aaia ien 6 Rear Views nn inner tennis rare etes nant een 6 4 Setting Up and Interfacing 7 1 Op en the Top Cover 7 2 Install the Toner Container 7 38 Close the Top Cover ss 8 4 Install the Waste Toner Bottle 8 5 Adjusting the Paper Guides in the Cassette and Adding Paper senior iei i teste 10 6 Open the Paper Stopper on the Face down Output Tray 12 7 Install the Face up Output Tray 12 8 Connect the Printer to the
40. s installed Kyocera s own PRESCRIBE 2e printer language Allows advanced graphic capabilities that allow you to print out any outline shape or solid form as well as providing a variety of special effects such as patterned fills gray scale shading a user accessible print image model and multiple page orientations and print directions within the same page Automatic rotation of fonts and graphics Images and fonts are automatically rotated to match the page orientation A wide variety of internal symbol sets The printer supports most PCL 6 symbol sets Display of printer messages in any of four languages English French German or Italian As an option it is also possible to download the mes sages in other languages Please contact your Kyocera dealer Memory card slot for option fonts macros forms etc Data in the memory card can be selectively read from the printers control panel Simple network management protocol SNMP compliance Offers network managers complete open network management Kyocera PrintMonitor Provides network wide management of the Kyocera FS family oflaser printers Refer to the readme file located in the Kyocera Digital Library CD ROM included with the printer for details PDF417 two dimensional bar codes The printer includes the capability that allows the user to implement the two dimen sional stacked bar code symbology PDF 417 or Portable Data File 417 XIV Introduction Options The follow
41. s you should take to avoid possible damages that may occur when the printer is used next time Moving the Printer When you move the printer O Move it gently O Keepit as level as possible to avoid spilling toner inside the printer O Ifyou need to move the printer to another location first remove the toner container waste toner bottle and developer unit After removing the developer unit from the printer put it into the supplied plastic bag and place it into the box in which the toner container is packaged Make sure that the waste toner bottle is securely capped and place it in the plastic bag together with the toner container Be sure to consult a service man before attempting long distance transportation of the printer 1 Remove the developer unit 2 Close the protect cover 3 Pack the developer unit 1 Disconnect Developer unit Toner container box Plastic bag supplied To reinstall the developer unit in the printer use the reverse procedure of the above xi Introduction ENERGY STAR As an ENERGY STAR Partner Kyocera Corporation has determined thatthis product meets the ENERGY STAR guidelines for energy effi ciency PTA The basic objective of the ENERGY STAR Program is to reduce environmental pollution by encouraging the manufacture and sale of equipment that uses energy more efficiently This printer is equipped with a sleep timer function that conforms with the standards ofthe
42. se instructions for later use Unplug this product from the wall outlet before cleaning Do not use this product near water Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings in the cabinet and the back are provided for ventilation to ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation unless proper ventilation is provided This product is equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the purpose of the grounding type plug Do not allow anything to rest on the power cord Do not locate this product where per sons will walk on the cord If an extension cord is used with this product make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord ampere rating Never push objects of any kind into this product through cabinet slots as
43. t Guidelines 1 10 11 12 Software shall mean the digitally encoded machine readable scalable outline data as encoded in a special format as well as the UFST Software You agree to accept a non exclusive license to use the Software to reproduce and display weights styles and versions of letters numerals characters and symbols Typefaces solely for your own customary business or personal purposes at the address stated on the registration card you return to Agfa Japan Under the terms of this License Agreement you have the right to use the Fonts on up to three printers Ifyou need to have access to the fonts on more than three printers you need to acquire a multi user license agreement which can be obtained from Agfa Japan Agfa Japan retains all rights title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement To protect proprietary rights of Agfa Japan you agree to maintain the Software and other proprietary infor mation concerning the Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and Typefaces You agree not to duplicate or copy the Software or Typefaces except that you may make one backup copy You agree that any such copy shall contain the same proprietary notices as those appearing on the original This License shall continue u
44. ve dust Vibration Ammonia or other harmful fumes If you are planning to fumigate the room or make liberal use of insecticide remove the printer first Excessive sunlight or humidity Lack of ventilation Low air pressure e g located more than 2000 meters 6500 feet above sea level 20000200 200 1 Positioning the Printer Basic requirements The printer will work best if it is installed in a location that is O Near the computer Ifthe parallel interface is used to connect the printer to the computer the connecting cable should be shielded type and not be longer than 3 meters 10 feet O Level and well supported Place the printer on a sturdy table or desk Do not place the printer on an unstable cart stand or table The printer may fall causing injury or serious damage to the printer O Near an AC wall outlet preferably one that can be used for the printer alone see section Power Supply on next page Power requirements are 120 V U S A Canada 220 to 240 V European countries Voltage 10 at each voltage 60 Hz 120 V 2 ERPRUENES 50 60 Hz 220 to 240 V 2 FS 1750 Max 5 8 A at 120 V or Max 3 A at 220 to 240 V Current capacity ES 3750 Max 7 8 A at 120 V or Max 4 A at 220 to 240 V The outlet should be earthed or an adapter should be used If an extension cord is used the total length of the power cord plus extension should be 5 meters 17 feet or les
45. y to laser products manufactured after August 1 1976 Compliance is mandatory for products marketed in the United States A label indicating compliance with the CDRH reg ulations must be attached to laser products marketed in the United States A KYOCERA FS 3750 120V 60Hz 78A KYOCERA CORPORATION MIE PLANT TAMAKI D 204 19 NIMO AVARI IOWI GIATARAL GOUR I MIE PRE JAPAN MANUFACTURED AHIS LASER PRODUCT CONAN TO INE APPUCAOUE RUES OF IDEAL A EHAPIEN SUBCHAPTER nsen UL 1959 US LISTED pes ily Par 15 al tho FCC fates in be lle ora dus de la cause B est ottaen A la noue MDG93 du Gera wm MADE IN JAPAN CAUTION TEMOVE POWER cono BRFORR sence AND FUSE REPLACE HA ATTENTION OUN privenia LES Goes ELEC ITUCUES COUPER UALIMENTATIOH M be REMPLAGER Ue FUSING PR ERMA DU GAMGIANE FTESIOILI O Di ESECUIFE NIPARAZION STACGATE AU DI ALIMENTAZIONE U S A Canada Ozone concentration The labels shown are affixed to the FS 3750 Similar labels are affixed to same location on the FS 1750 The printers generate ozone gas 03 which may concentrate in the place of installation and cause an unpleasant smell To minimize concentration of ozone gas to less than 0 1 ppm we recommend you not to install the printer in a confined area where ventilation is blocked vi Introduction IMPORTANT SAFEGUARDS 1 2 3 4 5 10 11 Read all of these instructions and save the
Download Pdf Manuals
Related Search