User manual
Contents
1. 6 8 6 5 TPT 8020A User manual 6 2 3 Short When two wires or more are attached to each other the tester is able to detect shorts report it at the bottom of the screen with the corresponding pin numbers and scrolling display for shorts of multi pairs If a remoter is connected to the other end of a cable a will be displayed in the position under the numbers of short pairs while one ended test only displays shorts pin number instead of wiremap Example For above situation see below Cable Test 12345678 H1 12345644 Short 78 6 6 TPT 8020A User manual 6 2 4 Miswire Miswire A wire or more wires are not connected to the correct pins at the other end of the cable There is one special kind cable 1 2 pair on one end to the 3 6 pair on the other This cable can be used to connect the two PCs If miswire was detected the LCD will display Miswire on the last line The one ended test mode doesn t support this function Example Wire 2 is connected to wire 3 on the other end See the displays below Cable Test 12345678 R1 13245678 Miswire 6 12. this function to trace its termination The tester flash the link LED indicator on the port of HUB or switch The tester will first find an active link entering this function interface See the display Flash link LED If an Ethernet link is active the world Flashing will be displayed on LCD and LED on the tester flashes simultaneously Flash link LED Link found Flashing 6 6 Ping Test Ping test is for testing the network connectivity using the ICMP protocol Before IP testing the IP address and the target IP 6 11 TPT 8020A User manual Press OK repeatedly to select a wire pair to be tested See the display below Length Test Unit 50 0pF m Pair Len 1 5m 6 4 Tone Generator The tester can generates audio tones for use with tone tracers on all pairs a selected pair or a selected pin in this mode Press t or to select wires or wire pairs for tone sending Do not connect the remoter and other devices to the other end of the cable Select the single wire can get the strongest signal Press or to change tone High Low Tone1 Tone2 Tone Generator Pin 12345678 Tone High 6 5 Flash Link LED When a cable connected to a switch or HUB you can use 6 10 TPT 8020A User manual 6 2 Cable Test Connect a remoter to one end of the cable and the tester to the other end for a full cable test Without remoter on the other end the tester will automatically perform the
3. to change the system language This is the system set menu system Set Language Bsitelisir 22 7 1 TPT 8020A User manual 3 Verification Verification is necessary before you begin using the tester This chapter provides an overview of your tester 3 1 Unpacking the tester Before unpacking please check whether there is any damage in the carton If any verify all parts per the packing list or Section 3 2 and perform self check per Section 3 4 till in the new tester is in normal operation In case that damaged bag or incomplete parts happen or the tester cannot achieve function tests please report to us immediately 3 2 Package Checklist TPT 8020A tester kit includes TPT 8020A tester RJ11 to RJ45 cable RJ45 to RJ45 cable 3 1 TPT 8020A User manual 3 3 Power Supply The TPT 8020A use 9V typical battery When the battery low icon which display on the top right is flashing the battery should be replaced as soon as practical Press marking OPEN lock and push down the battery cap then pull out battery snap and connect a new battery Don t pull the battery line directly when replacing the battery 3 4 Power On and Self Check When first time you use the tester must run a self test as follows Install a f Tester will turn on and display new welcome interface then run battery initialization and display main menu Note Disconnect any cables when running in initializing Press SETUP key in ma
4. other end Ping lest My 192 168 001 009 Ta 192 168 001 010 TPT 8020A User manual address of the tester must be set first If these two address are not in the same LAN the gateway and subnet mask should be set too 6 6 1 Quick Setup For easy to use please set the tester s IP and the target IP follow these steps A Press OK to select the tester s IP with the selected value highlighted B Press or gt to go to the number of IP address to be modified and press 1 or to change the value C Press OK key again and select the target IP D Set the target IP according to B then press OK to escape and start a ping test Example The following diagram shows modifying the last value of the tester s IP Ping lest My 192 168 001 ras Target IP Ta 192 168 001 010 Ping 6 6 2 Complete Setup In the Ping test mode press SETUP key to enter the Ping Setup screen in which you may modify values of My IP tester s 6 12 TPT 8020A User manual 6 Function Description Press POWER key to power on the tester then select a function to begin test To turn the tester off hold POWER key until the display turns off The tester can save the last testing state after power off When connecting to unknown jacks or cables it is best to begin with Jack ID test mode The following chapters will take you through every test function in details 6 1 Jack ID The Jack I
5. D test identifies what equipment connected to the other end of the jack or cable The test first looks for voltage being present on the connector pins If voltages are found in the telephone volt range the LCD will display this voltage If no voltage is detected test for the Ethernet link pulse If the link pulses are detected the tester will report the Ethernet information i e speed The tester default cable for connecting is the straight through cable In case the network card is connected to the other end of the cable the tester will display NIC while HUB or SWITCH is connected the tester will display HUB or SWITCH Warning if you use the crossover cable to connect the tester the tester will incorrectly display HUB or SWITCH instead of NIC In the case where the tester reports Auto MDI MDI X it means the remote device supports auto adapting crossover and straight through cables The tester will display POE Equipment if a POE Power over Ethernet device is connected Such equipment typically provides power for IP phones or wireless transceivers on the Same wires that carry the Ethernet data signals 6 1 TPT 8020A User manual IP Phone LM equipment SWITCH If the tester connects to a POE cable like this The tester will display that a POE device has been detected POE Equipment 100BASE TX full HUB or SWITCH Press OK to start a new test 6 2 TPT 8020A User manual
6. TPT 8020A User manual Contents LHCFOGUCTION see 1 1 PD DP Cal aNCe seele 2 1 NTPC AG OM ea dat hanna meine ena eae tenants 3 1 3 1 Unpacking the tester eeeeeeeeeeeeee 3 1 3 2 Package Checklist x eei E EE i 3 1 35 9 POWT SUDD nee 3 2 3 4 Power On and Self Check eere 3 2 User Interface nung 4 1 Interface and Menu Management zusssessnnnnnnnnnnnn nn 5 1 F UNELION DESERIPEION nenn 6 1 5 Jack Dessen 6 1 6 2 CADIS Test ee 6 1 9 21 CablePAS Sirie 6 3 0 2 2 ODER ee E ebene 6 4 02 9 GNO amaa 6 6 DOSE MISWI G asinn aa a Ta D 6 7 62 9 SPIE Pall rrna vta vie Dx O inn UE 6 8 6 5 EENGEN Test nnd 6 9 6 4 Tone Generator sce cssssnesspemieracmneerecnenenatnnernanes 6 10 6 5 Flash Wink WED SEHE 6 10 626 lt PING Test ae eilt 6 11 TPT 8020A User manual 6 6 1 Quick SOLID use eier 6 12 6 6 2 Complete Setup eene 6 12 6 6 3 Test Status Introduction 6 13 0 7 DHCP TES ee ee eer USD CU MEDIUM 6 15 8 9 E CA ee od bete pda tanc ders dtt edd 6 16 MEE I II TIT 7 1 Fok WANGUAG rennen 7 1 2 CUON ee na nee ee 8 1 Cl PUNO OM near 8 1 8 2 WSC SEU Gilden 8 1 9 Appendix A How to use Tone traCeP sseeseeeeeeeeeeeeees 9 1 TPT 8020A User manual 9 Appendix A How to use Tone tracer Nothing connected Press while testing Battery Indicator Battery Low When pressing the test button of tone
7. cceed the tester display numbers of packets Ta 192 168 001 010 TPT 8020A User manual 5 Interface and Menu Management First time power on the tester will display initializing and then the main menu in 8 sec lt lt lt Function gt gt gt 1 Jack ID 2 Length Test 3 Cable Test Press t or key to select a function in the main menu and press OK key to start the selected function Press ESC key can return to main menu in any function Function Table 1 Jack ID Indentify possible conditions of an RJ45 jack 2 Length Test Test cable length 3 Cable Test Test cable for shorts opens and split pairs display wiremap 4 Tone Generator Generate Tone on all pairs of cable 5 Flash Link LED Blinking a link indicator to find a HUB or switch port 6 Ping Test Ping to verify connectivity of devices 7 DHCP Test Dynamically acquire IP DNS host and Gateway and detect network connectivity 8 Net Scan Scan active devices in the LAN 9 1 TPT 8020A User manual IP Target IP Gateway and Subnet Mask and view the MAC physical address of the tester Ping Set MyIP 8 68 001 008 Operations A Press or gt to move the cursor B Press 1 or to change the value C Press OK to select MyIP Target IP Gateway NetMask MAC D Press ESC return to Ping Test mode 6 6 3 Test Status Introduction A Link not Found The cable was disconnect or no device on the
8. er can use the RJ45 to Alligator clip cable and set pair 1 2 The tester automatically runs a new test every second The LCD displays is shown below Length Test Unit 49 0pF m Pair 1 2 Len 1 5m Press t or 1 to adjust the capacitance per unit length and the tester will display as follows Length Test Unit D F m Pair 1 2 Len 1 5m For cables of unknown capacitance per unit length a cable of known length of the same kind will be as the cable whose length is to be measured is connected to the tester To reduce the error at maximum it is suggested to use the cable above 20 meters 6 9 TPT 8020A User manual TPT 8020A User manual 6 2 5 Split Pair The twisted pair cables are made up of eight wires twisted together in 4 pairs T568A B standard prescribes the pairs 1 2 3 6 4 5 7 8 A split pair cable is wired with correct continuity but not with correct pairing For a long cable split pair fault will Example greatly affect the signal transportation Example Qo c CR Cn BR Go Bo CO cJ CR On B amp MI For the above situation the tester displays as follow Cable Test Wires 1 3 are twisted together wires 2 6 are twisted together LCD displays is shown below 12345678 H1 3456 8 Cable Test Open 12345678 Ri 12345678 Split 1236 corresponding pair at the remote end won t be displayed Open will be displayed on the last line and pin 1 amp 2 for the
9. in menu to display the battery capacity and enter system setup menu Press ESC key return to main menu Check battery status 3 2 TPT 8020A User manual Scan progress Net Scan Amount of found devices Found 005 The tester stops scan when it gets to the end of the IP range User can press OK to interrupt a scan progress Press t Jor to see the device s IP and MAC Example Amount of found devices See number 001 005 IP 192 168 001 009 MAC 00E04C582D84 Note Maximal records can save 255 devices information TPT 8020A User manual Try times for DHCP Test connecting DHCP host Requesting If got response from the DHCP host LCD display as follow DHOP Test Got a IP for the tester Got response My 192 168 001 002 Press OK to Ping Press OK once to ping the DNS server Press OK twice to ping the Gateway Press OK thrice to ping a target IP Press SETUP to set the target IP 6 8 Net Scan You must press SETUP to set the IP range before a new test Press ESC return to net scan mode after set the range then press OK to start a scan test The follow screen display that the tester is scanning OK Key Enter into a test mode or move to next screen TPT 8020A User manual 4 User Interface The TPT 8020A tester is very easy to use To help you make full use of its extensive and flexible testing capabil
10. ities please read through this chapter carefully Link Indicator Cursor Keys Menu Backlight selection Scroll and LCD adjust values Power Key Short press to control back light Hold to turn off on tester Setup Key Set ESC Return to arameters i higher level menu Battery Cap Press lock and push down TPT 8020A User manual Tx transmit packets Rx receive packets If the two values are not the same it means that some packets may be lost D IP Conflict When the tester s IP has been used by other devices the LCD displays MyIP is used E No ARP response In case the target IP devices in the network are not being in use or switch off the tester will display No ARP response F Ping Fail Because of network problem or intercepted by Firewall no ping packets response 6 7 DHCP Test In DHCP test mode the tester can get its network information including tester s IP DNS server s IP and Gateway s IP from a DHCP host Press OK to ping these devices When the tester find an active link it will display as follow TPT 8020A User manual B Doing ping test When detecting an active link the tester will start Ping test automatically See the below display Ping Test My 192 168 001 009 Ta 192 168 001 010 Ping C Ping OK When a response is received Ping Test My 192 168 001 009 Ta 192 168 001 010 Ping OK lt 1ms If Ping su
11. one end test One end test mode can only diagnose cable faults for shorts and split pairs but unable to display the wiremap The tester will automatically perform a new test every 3 seconds with Testing displaying If you connect a cable immediately at that time you ll only get the incorrect result You d better connect the cable to be tested before testing See the connection diagram below 6 2 1 Cable PASS If the cable conforms to the T568A B the tester will display PASS and report cable length If the remoter was connected the tester will display its serial number S at the end of the wire map means the cable is STP Wiremap at the tester end Wiremap at the Ri 123456788 R moter end Serial Number of 6 3 PASS 1 5m TPT 8020A User manual See the below diagram of correct wire arrangement per T568A B One end Test pass cable tester displays as follow Cable Test One end Test PASS 1 5m 6 2 2 Open This error can only be detected with remoter in the manner of pairs which are wired to T568A B as 1 amp 2 3 amp 6 4 amp 5 and 7 amp 8 The tester will report Open when any wire is not attached to a pin correctly 6 4 TPT 8020A User manual 6 3 Length Test The length test function measures the length of a cable by measuring its capacitance it is supported in one end test mode The capacitance per unit length can be adjusted When test a cable un crimped us
12. splaying thus allowing easy management of LAN Quantity Main Function TPT 8020A tester e For twisted pair coax cable and security wire etc testing e Intuitive LCD display of wiremaps e Conduct tests of STP UTP and diagnoses faults for opens shorts and Perform cable tests per T568A B standard Maximal cable length for testing 457 meters Test several cables simultaneously by selecting multi remoter Quick identification at unknown RJ45 jacks Support static and dynamic DHCP IP configuration Ping test to detect faults i e packet loss Find active device with NetScan function Blinks link indicator to identify cable termination on hub or router Generates selectable tones on selected pins for use with tone tracers LCD displayer with backlight 3 1 TPT 8020A User manual 8 Cautions 8 1 Auto off The tester turns off automatically when none key was press for a long time LCD back light will turn off after 5 minutes The tester will turn off after 15 minutes in all modes except Tone Generator which is 60 minutes and Flash Link LED which is 30 minutes 8 2 User set data To preserve user set data the tester must be off by holding POWER key and the battery disconnected for no more than one minute 8 1 TPT 8020A User manual 2 Appearance 2 1 TPT 8020A User manual TPT 8020A User manual 7 System Set Press SETUP in the main menu the tester will enter system set mode 7 1 Language Press or gt
13. tracer the battery indicator turn on all the time means battery should be replaced as soon as possible 9 1 TPT 8020A User manual TPT 8020A User manual 3 Verification 1 Introduction Verification is necessary before you begin using the tester The TPT 8020A is an easy to use and portable test set with This chapter provides an overview of your tester advanced cable locator and simple network tester in one unit 3 1 Unpacking the tester Besides identifying wiremap measuring the cable length diagnosing cable faults for opens and shorts etc and tracing cables the TPT 8020A can also be used to detect the outlet connectivity and device types i e PBX and Ethernet etc and generate distinctive tones for tracing cable termination in the wall ceiling and DDF Besides its has comprehensive network test functions including static and dynamic DHCP IP configuration PING test for connectivity to network devices Before unpacking please check whether there is any damage in the carton If any verify all parts per the packing list or Section 3 2 and perform self check per Section 3 4 till in the new tester is in normal operation In case that damaged bag or incomplete parts happen or the tester cannot achieve function tests please report to us immediately through ICMP network protocol and NetScan for scanning 3 2 Package Checklist active hosts in the LAN with detected host quantity and IP MAC TPT 8020A tester kit includes address di
Download Pdf Manuals
Related Search