User Manual
Contents
1. 1 1 Liability Statement Every effort has been made to ensure that this product is free of defects Audio Authority cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use It is the responsibility of the user of the hardware to check that it is suitable for his her requirements and that it is installed correctly All rights reserved No parts of this manual may be reproduced or transmitted by any form or means electronic or mechanical including photocopying recording or by any information storage or retrieval system without the written consent of the publisher Audio Authority reserves the right to revise any of its hardware and software following its policy to modify and or improve its products where necessary or desirable This statement does not affect the legal rights of the user in any way All third party trademarks and copyrights are recognized The Audio Authority logo and Double A logo are the registered Trademarks of Audio Authority All other trademarks are the property of their respective holders 1 2 Features e Composite video S Video or YCbCr inputs to PC HD outputs e PC Resolutions to 1280x1024 e All HDTV Progressive Scan resolutions e 32Mb frame memory e Integral picture adjustments On screen display for setup and adjustment Locking DC power connector for reliability 1 3 Getting the Best Results There are many factors affecting the quality of2. turn off the OSD menu left corner by pressing the menu button or cycle power on the 1362 Press the button until you see a picture on the display you should see the input menu in the upper right of the display If you cannot see the input menu try switching picture modes or try a different 1362 output resolution such as 720p that may better fit your screen If you still see no video image simultaneously press menu and buttons to reset the 1362 to 480p for HDTV If your display device is a PC monitor reset to XGA by pressing the and buttons If all connections are correct the output setting is most likely the problem Make sure the display is capable of accepting the resolution and refresh rate selected and make sure the output format selected RGB or YPbPr is appropriate for the type of cable being used at the output If none of these measures solve the problem call Audio Authority Technical Support at 800 322 8346 Monday through Friday 8 30am to 5 00 pm EST or e mail support audioauthority com 10 7 0 LIMITED WARRANTY Should any consumer product from Audio Authority fail due to defects in materials or workmanship within one year from the date of the original sale to the end user Audio Authority guarantees that we will replace the defective product at no cost Freight charges for the replacement unit will be paid by Audio Authority Ground service only A copy of the invoice showing the item number and date o
3. results when scaling video signals Some basic precautions will ensure the best possible performance from your 1362 Video Scaler Output Display Device The quality of the output signal will depend largely upon the type and quality of display device used For instance some video projectors perform better than others Using Compatible Resolutions Set the output resolution of the 1362 to the resolution and refresh rate most compatible with the display device This allows the 1362 to do most of the work which usually results in a superior picture The 1362 HDTV output resolutions include 480p 720p and 1080i at 50Hz or 60Hz Distance Between The 1362 And The Display Device This plays a major role in the final result Long distances are possible but special measures should be taken in order to avoid cable losses These include using high quality coax type VGA cables Line amplifiers may also be necessary Output Connection Cables Low quality cables are susceptible to interference They degrade signal quality due to poor matching and cause elevated noise levels Therefore cables should be of the best quality Coax type computer cables are recommended because of their superior internal shielding Characteristics Interference From Nearby Electrical Devices These can have an adverse effect on signal quality For example an older computer monitor often emits very high electromagnetic fields that can interfere with the performance of v
4. User Manual Model 1362 AudioAPAuthority Model 1362 H Composite Video to YPbPr VGA Converter www audioauthority com Composite Video to YPbPr VGA Video Converter AudioGpAuthority 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 Table Of Contents Introduction 64 24 od A Re A 3 Specifications cestos ea ee a ee 5 Checking Package Contents 0 4 6 Connecting the Hardware 2 6 Operating The Unit 0 kann aka 7 Troubleshooting 0 e eee 10 Limited Warranty 22 aar kaka ka kr knr nn 11 Regulatory Compliance 12 Contact Information vr rv rn rea 12 1 0 INTRODUCTION Thank you for purchasing this 1362 Video Converter from Audio Authority The 1362 has many uses but the vital need it answers is in a mixed signal distribution system Some high definition signal distribution systems include one or more standard definition sources To distribute these signals to HDTVs a quality scaler is required Model 1362 converts a standard analog NTSC or PAL video signal to HD component video YPbPr Input may be either composite S Video standard definition component YCbCr or RGsB format Output may be YPbPr or RGBHV Audio Authority also offers an extensive line of audio and video switchers converters and distribution amps splitters available for purchase online at www audioauthority com
5. e OSD on the display device connected to the output e and Buttons These buttons allow navigation within the menu and adjustments of the parameters available e XGA Reset Simultaneously pressing the and buttons returns settings to factory defaults and sets the output to XGA for PC monitors e 480p Reset Simultaneously depressing the menu and buttons returns settings to factory defaults and sets the output to 480p for HDTV displays Pressing the menu button displays the main menu Move the cursor to the desired setup option by using the and buttons When you reach the option you desire press the menu button again to select that option Once the desired option is reached and selected a new menu will appear use the and keys to select the parameter you wish to change or adjust 5 2 Menu Map Display Setup Exit Return to main menu o to main menu Advanced Setup Film Mode Select between auto or off for film detection OSD Display Turn On Screen Display on or off No Signal Select blue or black screen when no signal is detected System Information Input Mode Displays current input format Display Timing Displays current output resolution RE ne en 5 3 Setup Example If you select the first item on the main menu Picture Adjust a secondary menu shows the following items Brightness Contrast Color Tint H Peaking Sharpness V Peaking Reset Exit Filter Filter If y
6. eceive the defective unit back at the factory it will be evaluated under the conditions of this warranty and if found to be in warranty a full credit will be issued to the Customer s Credit Card Return freight charges for the defective unit are the customer s responsibility Please contact our Technical Service Department for complete details concerning all in and out of warranty service matters We appreciate your confidence in our products and services and will always strive to meet or exceed your needs 11 8 0 REGULATORY COMPLIANCE This product complies with the relevant standards for FCC and CE approval The Power Adaptor Supply has been tested for compliance with UL CSA amp CE Regulations 9 0 CONTACT INFORMATION Should you have questions or require assistance with this product in areas not covered by this manual please contact Audio Authority using the information below Audio Authority Technical Service 800 322 8346 M F 8 30 AM to 5 00 PM EST International 859 233 4599 Fax 859 233 4510 Send email to support audioauthority com Audio Authority Corporation 2048 Mercer Road Lexington Kentucky 40511 1071 USA AudioGp Authority 2048 Mercer Road Lexington Kentucky 40511 1071 Phone 859 233 4599 Fax 859 233 4510 Customer Toll Free USA amp Canada 800 322 8346 Website http www audioauthority com 752 524 3 07
7. f purchase proof of purchase must be submitted with the defective unit to constitute a valid in warranty claim Units that fail after the warranty period has expired may be returned to the factory for repair at a nominal charge if not damaged beyond the point of repair All freight charges for out of warranty returns for repair are the responsibility of the customer Units returned for repair must have a Return Authorization Number assigned by the factory This is a limited warranty and is not applicable for products which in our opinion have been damaged altered abused misused or improperly installed Audio Authority makes no other warranties either expressed or implied including limitation warranties as to merchantability or fitness for a particular purpose Additionally there are no allowances or credits available for service work or installation performed in the field by the end user Warranty Service Procedures If you suspect a product defect contact Audio Authority s Technical Service Department at 800 322 8346 or 859 233 4599 for assistance in verifying the problem If a defect or potential defect is suspected a replacement unit will be shipped immediately on a defect exchange basis and a Return Authorization Number will be issued for the return of the defective product Replacement units are sent out at the Manufacturer s Suggested Retail Price which is debited to the Customer s Credit Card at the time of shipment Once we r
8. ideo equipment in its proximity 2 0 SPECIFICATIONS Input Format Composite Video S Video or YCbCr Input Signal Levels Composite Video O 1V p p 75Q S Video OY 1V p p C 0 7 V p p 75Q Pb Cb Pr Cr 0 7V p p 75Q Output Format Output Signal Levels RGBHV YPbPr RGB 0 7V p p 75Q H amp V Sync O 3 5V p p TILY O 1V p p 75Q Pb Pr 0 7V p p 75Q Input Connector Type Input CV RCA S Video 4 Pin DIN YCbCr 8 pin DIN Output Connector Type Control HD 15 Front Panel Buttons Information Display On Screen Display Video Adjustments Power Source Brightness Contrast Color Tint Sharpness H amp V Peaking In Plug Switching Adapter 100 240VAC to 5VDC 2 0A Weight 1 5 lbs 680 grams Dimensions HxWxD 1x7 x4 25x175x100mm Accessories Included Power adapter composite video cable 8 pin Mini DIN to 3 RCA cable 6 ft HD15M cable user manual Output Signal Specifications PC Resolutions Vert Rate Scan Type 50 60 72 75 85 Hz Progressive 640x480 gre 50 60 72 75 85 Hz Progressive 800x600 50 60 70 75 85 Hz Progressive 1024x768 3 50 60 Hz Progressive 1280x768 50 60 Hz Progressive 1280x1024 f 9 HDTV Resolutions Vert Rate Scan Type 720x480 720x576 1280x720 1920x1080 50 60Hz 50 60Hz 50 60Hz 50 60Hz YPbPr RGBHV YPbPr RGBHV YPbPr RGBHV YPbPr RGBHV Note 2 Progressive Progressive Progressive Pseudo Interlaced The 1080i Output
9. is actually a doubled 540p signal It will appear as 1080i on most displays however it is not technically 1080i signal format 3 0 CHECKING PACKAGE CONTENTS Before attempting to use this unit please check the packaging and make certain the following items are contained in the shipping carton e Scaler Unit e 100 240VAC AC DC Power Adapter e Composite Video Input Cable e 8 Pin Mini DIN to 3 RCA Cable e 6 ft HD15M Cable e User Manual Note Please keep the original packing material in case the unit ever needs to be returned If you find any items are missing contact Audio Authority immediately Have the model number serial number and invoice available for reference when you call 4 0 CONNECTING THE HARDWARE The first step is to connect a video source to one of the inputs of the 1362 and to connect its output to a display device The drawing of the unit shows the location of the inputs output and power connectors cv DC 5V IN IN occo fee PC HD OUTPUT 480PTXGAY 00000 eC 00000 O MENU 00000 O O O INPUT 4 1 Connecting an Input The 1362 can accept composite Video S Video or YCbCr inputs Composite video is connected to the scaler via the RCA connector S video connects via the 4 Pin Mini DIN connector and YCbCr connects via the 8 Pin Mini DIN connector using the 3 RCA to 8 Pin Mini DIN cable provided 6 Proper signal levels are very important to the operation of this product so make sure your inpu
10. ou want to change the color level for example you would use the and keys to navigate to that Item on the menu and press the menu key again to select that option When color is selected a sub menu for the adjustment appears Color MN 48 Use the and buttons to increase or decrease the value of the setting Press menu again to leave the setting Move the arrow to exit and press menu enter again to exit 5 4 Display Setup When this is selected an output resolution sub menu appears PC SXGA 1280x1024050 60Hz WXGA 1280x768050 60Hz XGA 1024x768 50 60 70 75 85Hz SVGA 800x600060 72 75 85Hz VGA 640x480060 72 75 85Hz HDTV 720p YPbPr 576p YPbPr 480p YPbPr 1080i YPbPr 1280x720 50 60Hz 720x576 50 60Hz 720x480 50 60Hz 1920x1080 50 60Hz 1080i is actually 540p doubled see Note on Page 4 Use the and buttons to choose the desired PC or HDTV output resolution from the available selections in the sub menu 5 5 Advanced Setup Advanced setup allows you to turn off the Film Mode 3 2 pull down turn off the OSD On Screen Display and set the no signal display to either blue or black 5 6 System Information When this is selected the OSD allows changes to be made to the 1362 s current output resolution and vertical refresh rate 6 0 TROUBLESHOOTING e First check for faulty cables or bad connections e If you see no video image the 1362 may be set to the wrong input If it is on
11. ts are of the levels specified on page 4 If the unit does not seem to function correctly after all instructions in this manual are followed and the unit has power the most likely cause of the problem is high or low signal levels or the use of the wrong input cable Be sure to follow instructions in 5 0 4 2 Connecting the Output The 1362 scaler can output analog RGBHV or YPbPr formats When a PC RGBHV output is used select an HD 15 to HD 15 cable to connect the 1362 output to the destination device When an HDTV YPbPr output is used select an HD 15 to 3 RCA cable to connect the 1362 output to the destination device 4 3 Connecting Power to the Unit The 1362 is shipped with an in plug power adapter to convert 100 240VAC 50 60Hz to 5VDC Connect the DC output cord from the power adapter to the back of the unit and then plug the power adapter into an AC receptacle the power LED indicator illuminates 5 0 OPERATING THE UNIT The 1362 does not automatically sense the input you have connected You must identify the active input by pressing the key before you activate the menu Power all components in the signal path and press the key until the correct input name appears in the upper right corner of the screen composite S video YCbCr RGsB 5 1 Settings The 1362 is controlled via three buttons with status indicated by OSD On Screen Display See the menu map on page 9 e Menu Button This button displays the menu options via th
Download Pdf Manuals
Related Search