User Manual - Pro-Ject Audio Systems
Contents
1. 10 CD 3 75 BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Speed Box ll Dear music lover thank you for purchasing a PRO JECT AUDIO Speed Box ll The unit permits electronic speed change of your Pro Ject record player between 33 and 45 r p m and also permits the replay of shellac records by allowing 78 r p m with an appropriate pulley and cartridge In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse nes Important notice Only models with mains socket power supply 16V 190mA AC max lt i The Pro Ject Debut lll E Debut lll Phono SB 1 Xpression lll Comfort 2 Xperience Comfort RPM 6 1 SB and RPM 6 1 SB SuperPack may not be used with the Speed Box Connecting the record player Connect the low voltage plug of the power cable Output 16V from the Speed Box ll to the socket in the record player s motor V Make all connections whilst the Speed Box ll is disconnected from the power supply Mains power connection The Speed Box ll is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your house Connect the low voltage plug trom the power supply to the socket Power 16V before connecting the power supply to the mains Stand By Press and hold the speed change button Speed to p2. f the belt Use a piece of kitchen paper or a cloth to remove the belt Measure the height of the pulley above the plinth in order to ease correct refitting Using a small screwdriver loosen the grub screw in the neck of the pulley just enough to remove the pulley vertically without using force Refit the pulley in the opposite order Tighten the grub screw carefully making sure you do not overtighten it Fit the drive belt around the subplatter and the pulley Again use a piece of paper or cloth to avoid soiling the belt Replace the platter 78 r p m is not available with the Essential Debut lll E Xperience Basic 2 Xperience Comfort 2 Xperience Acryl 2 Xperience Classic 2 Xperience SuperPack 6 PerspeX 6 PerspeX SuperPack RPM 1 3 Genie RPM 9 1 RPM 9 1 SuperPack RPM 9 1 Acryl RPM 9 2 Evolution and S RPM 10 1 Evolution The models Debut lll Phono SB 1 Xpression lll Comfort RPM 5 SuperPack RPM 5 1 SuperPack RPM 6 1 SB RPM 6 1 SB SuperPack and Xtension are equipped with the 78 r p m pulley as a standard Technical specifications Pro Ject Speed Box ll Nominal speeds 33 and 45 r p m Optional 78 r p m Quartz oscillator Speed stability 0 001 Length power cable approximately 40cm Turntable connection 16V AC 190mA max 3W power consumption max Outboard power supply 16V 500mA AC suitable for your country s mains supply Dimensions W x H x D D with sockets 103 x 36 x 103 103 mm Weight 540g with
3. out power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions 5 for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to press The manufacturer reserves the right to make This guide was produced by Audio Trade GmbH changes to the technical specification without prior Copyright O 2005 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development Audio Trade GmbH Pro Ject Speed Box ll Revision 2013 2 1 3
4. ut the Speed Box ll into stand by Pressing the button Speed will switch on the Speed Box ll from stand by Switching on and off Pressing the power switch of your Pro Ject turntable alternately starts or stops the motor Speed selection 33 45 r p m gt o Project 33 45 Speed Box II Speed MY The belt must be on the smaller 50Hz models larger 60Hz models diameter part of the motor pulley Press the button Speed to switch between 33 and 45 r p m The selected speed is shown respectively by the lit LED To play at 45 or 78 r p m please always start the turntable at 33 r p m and then switch to the higher speed when it has attained full speed Replay at 78 r p m n order to replay shellac records at 78 r p m your turntable must be equipped with the 78 r p m pulley which is available as an optional accessory for most models After fitting the 78 r p m pulley please proceed as follows Remove the platter and using the tool from the accessory kit fit the belt around the larger diameter step of the pulley Replace the Platter start the turntable at 33 r p m and switch the speed to 45 r p m the platter will then revolve at 78 r p m 2 O Audio Trade GmbH Pro Ject Speed Box ll Revision 2013 2 1 Fitting the 78 r p m pulley Before beginning work fit the cartridge s needle protection cover Remove the platter and drive belt Please remember that sweat or sticky fingers will impair the function o
Download Pdf Manuals
Related Search